There are two cases in which the min_def isn't used:
a) if FILS will be enabled
b) if FTM responder is enabled
Both of these apply to AP mode only, but for FILS we're
not checking that right now. Change the code to iterate
the interfaces and links using the channel context, and
check for AP mode for both, not just for FTM responder.
In the case of iwl_mvm_enable_fils() this might also fix
an issue where FILS is enabled for an IBSS network that
happens to be started on 6 GHz, though that's not very
likely to be possible due to regulatory.
However for RX OMI bandwidth reduction the driver needs
to use the min_def in client mode as well, in order to
actually reduce bandwidth when it requested that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241231135726.7b91025e103d.I4c99c03fd32363d574ab5e34798b6099401f0729@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My recent restart related work has made this race more likely
to happen and we've now noticed it, but it seems that it was
always possible. The race is that the add stream work can be
scheduled just before a restart is scheduled and then execute
before the restart, accessing the device while it's doing the
restart and not accessible.
To fix this, check if the device is restarting and abort the
work in that case. Reschedule it after the restart as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241228223206.9c30af039b4d.I1a32936776f8ba5e83dda0a68ffc2722d9d37950@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to later add the ability to do deeper resets of the
device when it crashes, first restructure the firmware error
handling. Instead of having just a single nic_error() method
that handles all, split it:
- nic_error() just handles and prints the error itself,
- dump_error() synchronously creates an error dump, and
- sw_reset() will be called to request doing a SW reset.
This changes the architecture so that the transport is now
responsible for deciding how to do the reset, and therefore
the handling of reprobe if error occurs during reconfig
moves there, which necessitates adding a method there that
notifies the transport that the recovery was completed.
Actually introducing the model under which deeper resets can
be done will be in future patches.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241227095718.6d4f741ae907.I96a9243e7877808ed6d1bff6967c15d6c24882f0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Approximately three years ago, in commit ddb6b76b6f
("iwlwifi: yoyo: support TLV-based firmware reset"), the code
was (likely erroneously) changed to no longer treat error
interrupts as firmware errors. As a result, this meant that
the fw_restart counter was only applied in case of command
queue being stuck, which never seems to happen. Also, there's
no longer any way to set the mvm->fw_restart to a value that
doesn't match exactly the module parameter behaviour.
Instead of trying to fix this, simply remove the logic that
limits the number of restarts, it's clearly unused.
However, restore the logic that restart isn't unconditional,
by checking the module parameter.
Since the "fw_error" argument to iwl_mvm_nic_restart() is now
always true (except in the "never happens" case of CMD queue
stuck), just remove it too and treat command queue stuck the
same way as everything else.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241227095718.b0489daf323c.I0cd3233b2214c5f06e059f746041b19d08647e40@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, the sequence goes like this (among others):
1. flush all stations (including the AP ones) -> this will tell the
drivers to remove the stations
2. notify the driver the vif is not associated.
Which means that in between 1 and 2, the state is that the vif is
associated, but there is no AP station, which makes no sense, and may be
problematic for some drivers (for example iwlwifi)
Change the sequence to:
1. flush the TDLS stations
2. move the AP station to IEEE80211_STA_NONE
3. notify the driver about the vif being unassociated
4. flush the AP station
In order to not break other drivers, add a vif flag to indicate whether
the driver wants to new sequence or not. If the flag is not set, then
things will be done in the old sequence.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://patch.msgid.link/20241224192322.996ad1be6cb3.I7815d33415aa1d65c0120b54be7a15a45388f807@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Kalle Valo says:
====================
wireless-next patches for v6.13
Most likely the last -next pull request for v6.13. Most changes are in
Realtek and Qualcomm drivers, otherwise not really anything
noteworthy.
Major changes:
mac80211
* EHT 1024 aggregation size for transmissions
ath12k
* switch to using wiphy_lock() and remove ar->conf_mutex
* firmware coredump collection support
* add debugfs support for a multitude of statistics
ath11k
* dt: document WCN6855 hardware inputs
ath9k
* remove include/linux/ath9k_platform.h
ath5k
* Arcadyan ARV45XX AR2417 & Gigaset SX76[23] AR241[34]A support
rtw88:
* 8821au and 8812au USB adapters support
rtw89
* thermal protection
* firmware secure boot for WiFi 6 chip
* tag 'wireless-next-2024-11-13' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (154 commits)
Revert "wifi: iwlegacy: do not skip frames with bad FCS"
wifi: mac80211: pass MBSSID config by reference
wifi: mac80211: Support EHT 1024 aggregation size in TX
net: rfkill: gpio: Add check for clk_enable()
wifi: brcmfmac: Fix oops due to NULL pointer dereference in brcmf_sdiod_sglist_rw()
wifi: Switch back to struct platform_driver::remove()
wifi: ipw2x00: libipw_rx_any(): fix bad alignment
wifi: brcmfmac: release 'root' node in all execution paths
wifi: iwlwifi: mvm: don't call power_update_mac in fast suspend
wifi: iwlwifi: s/IWL_MVM_INVALID_STA/IWL_INVALID_STA
wifi: iwlwifi: bump minimum API version in BZ/SC to 92
wifi: iwlwifi: move IWL_LMAC_*_INDEX to fw/api/context.h
wifi: iwlwifi: be less noisy if the NIC is dead in S3
wifi: iwlwifi: mvm: tell iwlmei when we finished suspending
wifi: iwlwifi: allow fast resume on ax200
wifi: iwlwifi: mvm: support new initiator and responder command version
wifi: iwlwifi: mvm: use wiphy locked debugfs for low-latency
wifi: iwlwifi: mvm: MLO scan upon channel condition degradation
wifi: iwlwifi: mvm: support new versions of the wowlan APIs
wifi: iwlwifi: mvm: allow always calling iwl_mvm_get_bss_vif()
...
====================
Link: https://patch.msgid.link/20241113172918.A8A11C4CEC3@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since we no longer shut down the device in suspend, we also no longer
call iwl_mvm_mei_device_state() and this is a problem because iwlmei
expects this to be called when it runs its own suspend sequence. It
checks mei->device_down in iwl_mei_remove() which is called upon
suspend.
Fix this by telling iwlmei when we're done accessing the device.
When we'll wake up, the device should be untouched if CSME didn't use it
during the suspend time. If CSME used it, we'll notice it through the
CSR_FUNC_SCRATCH register.
Fixes: e8bb19c1d5 ("wifi: iwlwifi: support fast resume")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20241028135215.525287b90af2.Ibf183824471ea5580d9276d104444e53191e6900@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Revert commit dfdfe4be18 ("wifi: iwlwifi: remove retry loops in
start"), it turns out that there's an issue with the PNVM load
notification from firmware not getting processed, that this patch
has been somewhat successfully papering over. Since this is being
reported, revert the loop removal for now.
We will later at least clean this up to only attempt to retry if
there was a timeout, but currently we don't even bubble up the
failure reason to the correct layer, only returning NULL.
Fixes: dfdfe4be18 ("wifi: iwlwifi: remove retry loops in start")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20241022092212.4aa82a558a00.Ibdeff9c8f0d608bc97fc42024392ae763b6937b7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This shouldn't happen at all, since in station mode all MMPDUs
go through the TXQ for the STA, and not this function. There
may or may not be a race in mac80211 through which this might
happen for some frames while a station is being added, but in
that case we can also just drop the frame and pretend the STA
didn't exist yet.
Also, the code is simply wrong since it uses deflink, and it's
not easy to fix it since the mvmvif->ap_sta pointer cannot be
used without the mutex, and perhaps the right link might not
even be known.
Just drop the frame at that point instead of trying to fix it
up.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240808232017.45ad105dc7fe.I6d45c82e5758395d9afb8854057ded03c7dc81d7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, the driver handles SMPS decisions by tracking AP
capabilities, BT coexistence changes, sending necessary SMPS
frames to the AP, and updating firmware with RX chain info
using the RLC_CONFIG_CMD.
Starting with version 3 of the RLC_CONFIG_CMD, the firmware
takes over this responsibility. It now tracks SMPS, sends
frames, and configures the RLC.
In this patch:
1. Stop sending RLC_CONFIG_CMD when firmware supports RLC
offload (version 3), as rlc.rx_chain_info is not needed by
firmware, and no other field in the cmd is used.
2. Prevent the driver from forwarding any SMPS requests to
mac80211, i.e., the driver should not transmit SMPS frames
to the AP as firmware handles that.
3. Set NL80211_FEATURE_DYNAMIC_SMPS and NL80211_FEATURE_STATIC_SMPS
conditionally based on RLC version.
Signed-off-by: Daniel Gabay <daniel.gabay@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240808232017.45da23be1f65.I0d46db82dd990a82e8a66876fe2f5310bc9513be@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is a WARNING in iwl_trans_wait_tx_queues_empty() (that was
recently converted from just a message), that can be hit if we
wait for TX queues to become empty after firmware died. Clearly,
we can't expect anything from the firmware after it's declared dead.
Don't call iwl_trans_wait_tx_queues_empty() in this case. While it could
be a good idea to stop the flow earlier, the flush functions do some
maintenance work that is not related to the firmware, so keep that part
of the code running even when the firmware is not running.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240825191257.a7cbd794cee9.I44a739fbd4ffcc46b83844dd1c7b2eb0c7b270f6@changeid
[edit commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Kalle Valo says:
====================
wireless-next patches for v6.11
Most likely the last "new features" pull request for v6.11 with
changes both in stack and in drivers. The big thing is the multiple
radios for wiphy feature which makes it possible to better advertise
radio capabilities to user space. mt76 enabled MLO and iwlwifi
re-enabled MLO, ath12k and rtw89 Wi-Fi 6 devices got WoWLAN support.
Major changes:
cfg80211/mac80211
* remove DEAUTH_NEED_MGD_TX_PREP flag
* multiple radios per wiphy support
mac80211_hwsim
* multi-radio wiphy support
ath12k
* DebugFS support for datapath statistics
* WCN7850: support for WoW (Wake on WLAN)
* WCN7850: device-tree bindings
ath11k
* QCA6390: device-tree bindings
iwlwifi
* mvm: re-enable Multi-Link Operation (MLO)
* aggregation (A-MSDU) optimisations
rtw89
* preparation for RTL8852BE-VT support
* WoWLAN support for WiFi 6 chips
* 36-bit PCI DMA support
mt76
* mt7925 Multi-Link Operation (MLO) support
* tag 'wireless-next-2024-07-11' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (204 commits)
wifi: mac80211: fix AP chandef capturing in CSA
wifi: iwlwifi: correctly reference TSO page information
wifi: mt76: mt792x: fix scheduler interference in drv own process
wifi: mt76: mt7925: enabling MLO when the firmware supports it
wifi: mt76: mt7925: remove the unused mt7925_mcu_set_chan_info
wifi: mt76: mt7925: update mt7925_mac_link_bss_add for MLO
wifi: mt76: mt7925: update mt7925_mcu_bss_basic_tlv for MLO
wifi: mt76: mt7925: update mt7925_mcu_set_timing for MLO
wifi: mt76: mt7925: update mt7925_mcu_sta_phy_tlv for MLO
wifi: mt76: mt7925: update mt7925_mcu_sta_rate_ctrl_tlv for MLO
wifi: mt76: mt7925: add mt7925_mcu_sta_eht_mld_tlv for MLO
wifi: mt76: mt7925: update mt7925_mcu_sta_update for MLO
wifi: mt76: mt7925: update mt7925_mcu_add_bss_info for MLO
wifi: mt76: mt7925: update mt7925_mcu_bss_mld_tlv for MLO
wifi: mt76: mt7925: update mt7925_mcu_sta_mld_tlv for MLO
wifi: mt76: mt7925: add mt7925_[assign,unassign]_vif_chanctx
wifi: mt76: add def_wcid to struct mt76_wcid
wifi: mt76: mt7925: report link information in rx status
wifi: mt76: mt7925: update rate index according to link id
wifi: mt76: mt7925: add link handling in the mt7925_ipv6_addr_change
...
====================
Link: https://patch.msgid.link/20240711102353.0C849C116B1@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This flag is annoying because it puts a lot of logic into mac80211
that could just as well be in the driver (only iwlmvm uses it) and
the implementation is also broken for MLO.
Remove the flag in favour of calling drv_mgd_prepare_tx() without
any conditions even for the deauth-while-assoc case. The drivers
that implement it can take the appropriate actions, which for the
only user of DEAUTH_NEED_MGD_TX_PREP (iwlmvm) is a bit more tricky
than the implementation in mac80211 is anyway, and all others have
no need and can just exit if info->was_assoc is set.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240627132527.94924bcc9c9e.I328a219e45f2e2724cd52e75bb9feee3bf21a463@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When UATS isn't enabled (no VLP/AFC AP support), we need to still
set the right bits in the channel/regulatory flags, so remove the
uats_enabled argument to the parsing etc.
Also, firmware deals just fine with getting the UATS table if it
supports the command even if the bits aren't set, so always send
it, since it's also needed if BIT(31) is set, but the driver need
not have any knowledge of that. Remove 'uats_enabled' entirely.
Fixes: 0d2fc8821a ("wifi: iwlwifi: nvm: parse the VLP/AFC bit from regulatory")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240618195731.a81e7234c4f6.Ic0131180d38e0f1ead2f7fa0e7583407ceaa0bd1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/broadcom/bnxt/bnxt.c
1e7962114c ("bnxt_en: Restore PTP tx_avail count in case of skb_pad() error")
165f87691a ("bnxt_en: add timestamping statistics support")
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
