In the current xdp_xmit implementation, if any single frame fails to
transmit due to insufficient buffer descriptors, the function nevertheless
reports success in sending all frames. This results in erroneously
indicating that frames were transmitted when in fact they were dropped.
This patch fixes the issue by ensureing the return value properly
indicates the actual number of frames successfully transmitted, rather than
potentially reporting success for all frames when some could not transmit.
Fixes: 6d6b39f180 ("net: fec: add initial XDP support")
Signed-off-by: Gagandeep Singh <g.singh@nxp.com>
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should check whether the current SFI (Stream Filter Instance) table
is full before creating a new SFI entry. However, the previous logic
checks the handle by mistake and might lead to unpredictable behavior.
Fixes: 888ae5a395 ("net: enetc: add tc flower psfp offload driver")
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It appears that dpaa_enable_tx_csum() only calls skb_reset_mac_header()
to get to the VLAN header using skb_mac_header().
We can use skb_vlan_eth_hdr() to get to the VLAN header based on
skb->data directly. This avoids spending a few cycles to set
skb->mac_header.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These have been useful in debugging various problems related to frame
preemption, so make them available through ethtool --register-dump for
later too.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This was left as TODO in commit 01e23b2b3b ("net: enetc: add support
for preemptible traffic classes") since it's relatively complicated.
Where this makes a difference is with a configuration as follows:
ethtool --set-mm eno0 pmac-enabled on tx-enabled on verify-enabled on
Preemptible packets should only be sent when the MAC Merge TX direction
becomes active (i.o.w. when the verification process succeeds, aka when
the link partner confirms it can process preemptible traffic). But the
tc qdisc with the preemptible traffic classes is offloaded completely
asynchronously w.r.t. the MM becoming active.
The ENETC manual does suggest that this should be handled in the driver:
"On startup, software should wait for the verification process to
complete (MMCSR[VSTS]=011) before initiating traffic".
Adding the necessary logic allows future selftests to uphold the claim
that an inactive or disabled MAC Merge layer should never send data
packets through the pMAC.
This change moves enetc_set_ptcfpr() from enetc.c to enetc_ethtool.c,
where its only caller is now - enetc_mm_commit_preemptible_tcs().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The MMCSR register contains 2 fields with overlapping meaning:
- LPA (Local preemption active):
This read-only status bit indicates whether preemption is active for
this port. This bit will be set if preemption is both enabled and has
completed the verification process.
- TXSTS (Merge status):
This read-only status field provides the state of the MAC Merge sublayer
transmit status as defined in IEEE Std 802.3-2018 Clause 99.
00 Transmit preemption is inactive
01 Transmit preemption is active
10 Reserved
11 Reserved
However none of these 2 fields offer reliable reporting to software.
When connecting ENETC to a link partner which is not capable of Frame
Preemption, the expectation is that ENETC's verification should fail
(VSTS=4) and its MM TX direction should be inactive (LPA=0, TXSTS=00)
even though the MM TX is enabled (ME=1). But surprise, the LPA bit of
MMCSR stays set even if VSTS=4 and ME=1.
OTOH, the TXSTS field has the opposite problem. I cannot get its value
to change from 0, even when connecting to a link partner capable of
frame preemption, which does respond to its verification frames (ME=1
and VSTS=3, "SUCCEEDED").
The only option with such buggy hardware seems to be to reimplement the
formula for calculating tx-active in software, which is for tx-enabled
to be true, and for the verify-status to be either SUCCEEDED, or
DISABLED.
Without reliable tx-active reporting, we have no good indication when
to commit the preemptible traffic classes to hardware, which makes it
possible (but not desirable) to send preemptible traffic to a link
partner incapable of receiving it. However, currently we do not have the
logic to wait for TX to be active yet, so the impact is limited.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Current enetc_set_mm() is designed to set the priv->active_offloads bit
ENETC_F_QBU for enetc_mm_link_state_update() to act on, but if the link
is already up, it modifies the ENETC_MMCSR_ME ("Merge Enable") bit
directly.
The problem is that it only *sets* ENETC_MMCSR_ME if the link is up, it
doesn't *clear* it if needed. So subsequent enetc_get_mm() calls still
see tx-enabled as true, up until a link down event, which is when
enetc_mm_link_state_update() will get called.
This is not a functional issue as far as I can assess. It has only come
up because I'd like to uphold a simple API rule in core ethtool code:
the pMAC cannot be disabled if TX is going to be enabled. Currently,
the fact that TX remains enabled for longer than expected (after the
enetc_set_mm() call that disables it) is going to violate that rule,
which is how it was caught.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
PFs which support the MAC Merge layer also have a set of 8 registers
called "Port traffic class N frame preemption register (PTC0FPR - PTC7FPR)".
Through these, a traffic class (group of TX rings of same dequeue
priority) can be mapped to the eMAC or to the pMAC.
There's nothing particularly spectacular here. We should probably only
commit the preemptible TCs to hardware once the MAC Merge layer became
active, but unlike Felix, we don't have an IRQ that notifies us of that.
We'd have to sleep for up to verifyTime (127 ms) to wait for a
resolution coming from the verification state machine; not only from the
ndo_setup_tc() code path, but also from enetc_mm_link_state_update().
Since it's relatively complicated and has a relatively small benefit,
I'm not doing it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ferenc Fejes <fejes@inf.elte.hu>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
To gain access to the larger encapsulating structure which has the type
tc_mqprio_qopt_offload, rename just the "qopt" field as "qopt".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ferenc Fejes <fejes@inf.elte.hu>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
I have observed an issue where the RX direction of the LS1028A ENETC pMAC
seems unresponsive. The minimal procedure to reproduce the issue is:
1. Connect ENETC port 0 with a loopback RJ45 cable to one of the Felix
switch ports (0).
2. Bring the ports up (MAC Merge layer is not enabled on either end).
3. Send a large quantity of unidirectional (express) traffic from Felix
to ENETC. I tried altering frame size and frame count, and it doesn't
appear to be specific to either of them, but rather, to the quantity
of octets received. Lowering the frame count, the minimum quantity of
packets to reproduce relatively consistently seems to be around 37000
frames at 1514 octets (w/o FCS) each.
4. Using ethtool --set-mm, enable the pMAC in the Felix and in the ENETC
ports, in both RX and TX directions, and with verification on both
ends.
5. Wait for verification to complete on both sides.
6. Configure a traffic class as preemptible on both ends.
7. Send some packets again.
The issue is at step 5, where the verification process of ENETC ends
(meaning that Felix responds with an SMD-R and ENETC sees the response),
but the verification process of Felix never ends (it remains VERIFYING).
If step 3 is skipped or if ENETC receives less traffic than
approximately that threshold, the test runs all the way through
(verification succeeds on both ends, preemptible traffic passes fine).
If, between step 4 and 5, the step below is also introduced:
4.1. Disable and re-enable PM0_COMMAND_CONFIG bit RX_EN
then again, the sequence of steps runs all the way through, and
verification succeeds, even if there was the previous RX traffic
injected into ENETC.
Traffic sent *by* the ENETC port prior to enabling the MAC Merge layer
does not seem to influence the verification result, only received
traffic does.
The LS1028A manual does not mention any relationship between
PM0_COMMAND_CONFIG and MMCSR, and the hardware people don't seem to
know for now either.
The bit that is toggled to work around the issue is also toggled
by enetc_mac_enable(), called from phylink's mac_link_down() and
mac_link_up() methods - which is how the workaround was found:
verification would work after a link down/up.
Fixes: c7b9e80869 ("net: enetc: add support for MAC Merge layer")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20230411192645.1896048-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
A number of MDIO drivers make use of devm_mdiobus_alloc_size(). This
is only available when CONFIG_MDIO_DEVRES is enabled. Add missing
depends or selects, depending on if there are circular dependencies or
not. This avoids linker errors, especially for randconfig builds.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20230409150204.2346231-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Not all fec MDIO bus drivers support C45 mode transactions. The older fec
hardware block in many ColdFire SoCs does not appear to support them, at
least according to most of the different ColdFire SoC reference manuals.
The bits used to generate C45 access on the iMX parts, in the OP field
of the MMFR register, are documented as generating non-compliant MII
frames (it is not documented as to exactly how they are non-compliant).
Commit 8d03ad1ab0 ("net: fec: Separate C22 and C45 transactions")
means the fec driver will always register c45 MDIO read and write
methods. During probe these will always be accessed now generating
non-compliant MII accesses on ColdFire based devices.
Add a quirk define, FEC_QUIRK_HAS_MDIO_C45, that can be used to
distinguish silicon that supports MDIO C45 framing or not. Add this to
all the existing iMX quirks, so they will be behave as they do now (*).
(*) it seems that some iMX parts may not support C45 transactions either.
The iMX25 and iMX50 Reference Manuals contain similar wording to
the ColdFire Reference Manuals on this.
Fixes: 8d03ad1ab0 ("net: fec: Separate C22 and C45 transactions")
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230404052207.3064861-1-gerg@linux-m68k.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Autoneg bit in the advertising bitmap and state->an_enabled are
always identical. Thus, we will be removing state->an_enabled.
Use the Autoneg bit in the advertising bitmap to indicate whether
autonegotiation should be used, rather than using the an_enabled
member which will be going away. This means we use the same condition
as phylink_mii_c22_pcs_config().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When running "ethtool -S eno0 --groups rmon" without an explicit "--src
emac|pmac" argument, the kernel will not report
rx-rmon-etherStatsPkts64to64Octets, rx-rmon-etherStatsPkts65to127Octets,
etc. This is because on ETHTOOL_MAC_STATS_SRC_AGGREGATE, we do not
populate the "ranges" argument.
ocelot_port_get_rmon_stats() does things differently and things work
there. I had forgotten to make sure that the code is structured the same
way in both drivers, so do that now.
Fixes: cf52bd238b ("net: enetc: add support for MAC Merge statistics counters")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230321232831.1200905-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to of_property_read_bool().
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for net/can
Acked-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
====================
pull-request: bpf-next 2023-02-11
We've added 96 non-merge commits during the last 14 day(s) which contain
a total of 152 files changed, 4884 insertions(+), 962 deletions(-).
There is a minor conflict in drivers/net/ethernet/intel/ice/ice_main.c
between commit 5b246e533d ("ice: split probe into smaller functions")
from the net-next tree and commit 66c0e13ad2 ("drivers: net: turn on
XDP features") from the bpf-next tree. Remove the hunk given ice_cfg_netdev()
is otherwise there a 2nd time, and add XDP features to the existing
ice_cfg_netdev() one:
[...]
ice_set_netdev_features(netdev);
netdev->xdp_features = NETDEV_XDP_ACT_BASIC | NETDEV_XDP_ACT_REDIRECT |
NETDEV_XDP_ACT_XSK_ZEROCOPY;
ice_set_ops(netdev);
[...]
Stephen's merge conflict mail:
https://lore.kernel.org/bpf/20230207101951.21a114fa@canb.auug.org.au/
The main changes are:
1) Add support for BPF trampoline on s390x which finally allows to remove many
test cases from the BPF CI's DENYLIST.s390x, from Ilya Leoshkevich.
2) Add multi-buffer XDP support to ice driver, from Maciej Fijalkowski.
3) Add capability to export the XDP features supported by the NIC.
Along with that, add a XDP compliance test tool,
from Lorenzo Bianconi & Marek Majtyka.
4) Add __bpf_kfunc tag for marking kernel functions as kfuncs,
from David Vernet.
5) Add a deep dive documentation about the verifier's register
liveness tracking algorithm, from Eduard Zingerman.
6) Fix and follow-up cleanups for resolve_btfids to be compiled
as a host program to avoid cross compile issues,
from Jiri Olsa & Ian Rogers.
7) Batch of fixes to the BPF selftest for xdp_hw_metadata which resulted
when testing on different NICs, from Jesper Dangaard Brouer.
8) Fix libbpf to better detect kernel version code on Debian, from Hao Xiang.
9) Extend libbpf to add an option for when the perf buffer should
wake up, from Jon Doron.
10) Follow-up fix on xdp_metadata selftest to just consume on TX
completion, from Stanislav Fomichev.
11) Extend the kfuncs.rst document with description on kfunc
lifecycle & stability expectations, from David Vernet.
12) Fix bpftool prog profile to skip attaching to offline CPUs,
from Tonghao Zhang.
====================
Link: https://lore.kernel.org/r/20230211002037.8489-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We assume that the mqprio queue configuration from taprio has a simple
1:1 mapping between prio and traffic class, and one TX queue per TC.
That might not be the case. Actually parse and act upon the mqprio
config.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Regardless of the requested queue count per traffic class, the enetc
driver allocates a number of TX rings equal to the number of TCs, and
hardcodes a queue configuration of "1@0 1@1 ... 1@max-tc". Other
configurations are silently ignored and treated the same.
Improve that by allowing what the user requests to be actually
fulfilled. This allows more than one TX ring per traffic class.
For example:
$ tc qdisc add dev eno0 root handle 1: mqprio num_tc 4 \
map 0 0 1 1 2 2 3 3 queues 2@0 2@2 2@4 2@6
[ 146.267648] fsl_enetc 0000:00:00.0 eno0: TX ring 0 prio 0
[ 146.273451] fsl_enetc 0000:00:00.0 eno0: TX ring 1 prio 0
[ 146.283280] fsl_enetc 0000:00:00.0 eno0: TX ring 2 prio 1
[ 146.293987] fsl_enetc 0000:00:00.0 eno0: TX ring 3 prio 1
[ 146.300467] fsl_enetc 0000:00:00.0 eno0: TX ring 4 prio 2
[ 146.306866] fsl_enetc 0000:00:00.0 eno0: TX ring 5 prio 2
[ 146.313261] fsl_enetc 0000:00:00.0 eno0: TX ring 6 prio 3
[ 146.319622] fsl_enetc 0000:00:00.0 eno0: TX ring 7 prio 3
$ tc qdisc del dev eno0 root
[ 178.238418] fsl_enetc 0000:00:00.0 eno0: TX ring 0 prio 0
[ 178.244369] fsl_enetc 0000:00:00.0 eno0: TX ring 1 prio 0
[ 178.251486] fsl_enetc 0000:00:00.0 eno0: TX ring 2 prio 0
[ 178.258006] fsl_enetc 0000:00:00.0 eno0: TX ring 3 prio 0
[ 178.265038] fsl_enetc 0000:00:00.0 eno0: TX ring 4 prio 0
[ 178.271557] fsl_enetc 0000:00:00.0 eno0: TX ring 5 prio 0
[ 178.277910] fsl_enetc 0000:00:00.0 eno0: TX ring 6 prio 0
[ 178.284281] fsl_enetc 0000:00:00.0 eno0: TX ring 7 prio 0
$ tc qdisc add dev eno0 root handle 1: mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 hw 1
[ 186.113162] fsl_enetc 0000:00:00.0 eno0: TX ring 0 prio 0
[ 186.118764] fsl_enetc 0000:00:00.0 eno0: TX ring 1 prio 1
[ 186.124374] fsl_enetc 0000:00:00.0 eno0: TX ring 2 prio 2
[ 186.130765] fsl_enetc 0000:00:00.0 eno0: TX ring 3 prio 3
[ 186.136404] fsl_enetc 0000:00:00.0 eno0: TX ring 4 prio 4
[ 186.142049] fsl_enetc 0000:00:00.0 eno0: TX ring 5 prio 5
[ 186.147674] fsl_enetc 0000:00:00.0 eno0: TX ring 6 prio 6
[ 186.153305] fsl_enetc 0000:00:00.0 eno0: TX ring 7 prio 7
The driver used to set TC_MQPRIO_HW_OFFLOAD_TCS, near which there is
this comment in the UAPI header:
TC_MQPRIO_HW_OFFLOAD_TCS, /* offload TCs, no queue counts */
which is what enetc was doing up until now (and no longer is; we offload
queue counts too), remove that assignment.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The enetc driver does not validate the mqprio queue configuration, so it
currently allows things like this:
$ tc qdisc add dev swp0 root handle 1: mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 queues 3@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 hw 1
But also things like this, completely omitting the queue configuration:
$ tc qdisc add dev eno0 root handle 1: mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 hw 1
By requesting validation via the mqprio capability structure, this is no
longer allowed, and we bring what is accepted by hardware in line with
what is accepted by software.
The check that num_tc <= real_num_tx_queues also becomes superfluous and
can be dropped, because mqprio_validate_queue_counts() validates that no
TXQ range exceeds real_num_tx_queues. That is a stronger check, because
there is at least 1 TXQ per TC, so there are at least as many TXQs as TCs.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently it can happen that an mqprio qdisc is installed with num_tc 8,
and this will reserve 8 (out of 8) TXQs for the network stack. Then we
can attach an XDP program, and this will crop 2 TXQs, leaving just 6 for
mqprio. That's not what the user requested, and we should fail it.
On the other hand, if mqprio isn't requested, we still give the 8 TXQs
to the network stack (with hashing among a single traffic class), but
then, cropping 2 TXQs for XDP is fine, because the user didn't
explicitly ask for any number of TXQs, so no expectations are violated.
Simply put, the logic that mqprio should impose a minimum number of TXQs
for the network never existed. Let's say (more or less arbitrarily) that
without mqprio, the driver expects a minimum number of TXQs equal to the
number of CPUs (on NXP LS1028A, that is either 1, or 2). And with mqprio,
mqprio gives the minimum required number of TXQs.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since the blamed net-next commit, enetc_setup_xdp_prog() no longer goes
through enetc_open(), and therefore, the function which was supposed to
detect whether a BPF program exists (in order to crop some TX queues
from network stack usage), enetc_num_stack_tx_queues(), no longer gets
called.
We can move the netif_set_real_num_rx_queues() call to enetc_alloc_msix()
(probe time), since it is a runtime invariant. We can do the same thing
with netif_set_real_num_tx_queues(), and let enetc_reconfigure_xdp_cb()
explicitly recalculate and change the number of stack TX queues.
Fixes: c33bfaf91c ("net: enetc: set up XDP program under enetc_reconfigure()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
enetc_reconfigure() was modified in commit c33bfaf91c ("net: enetc:
set up XDP program under enetc_reconfigure()") to take an optional
callback that runs while the netdev is down, but this callback currently
cannot fail.
Code up the error handling so that the interface is restarted with the
old resources if the callback fails.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We keep a pointer to the xdp_prog in the private netdev structure as
well; what's replicated per RX ring is done so just for more convenient
access from the NAPI poll procedure.
Simplify enetc_num_stack_tx_queues() by looking at priv->xdp_prog rather
than iterating through the information replicated per RX ring.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Conversion to gpiod API done in commit 468ba54bd6 ("fec: convert
to gpio descriptor") clashed with gpiolib applying the same quirk to the
reset GPIO polarity (introduced in commit b02c85c945). This results in
the reset line being left active/device being left in reset state when
reset line is "active low".
Remove handling of 'phy-reset-active-high' property from the driver and
rely on gpiolib to apply needed adjustments to avoid ending up with the
double inversion/flipped logic.
Fixes: 468ba54bd6 ("fec: convert to gpio descriptor")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230201215320.528319-2-dmitry.torokhov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Conversion of the driver to gpiod API done in 468ba54bd6 ("fec:
convert to gpio descriptor") incorrectly made reset line mandatory and
resulted in aborting driver probe in cases where reset line was not
specified (note: this way of specifying PHY reset line is actually
deprecated).
Switch to using devm_gpiod_get_optional() and skip manipulating reset
line if it can not be located.
Fixes: 468ba54bd6 ("fec: convert to gpio descriptor")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230201215320.528319-1-dmitry.torokhov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A summary of the flags being set for various drivers is given below.
Note that XDP_F_REDIRECT_TARGET and XDP_F_FRAG_TARGET are features
that can be turned off and on at runtime. This means that these flags
may be set and unset under RTNL lock protection by the driver. Hence,
READ_ONCE must be used by code loading the flag value.
Also, these flags are not used for synchronization against the availability
of XDP resources on a device. It is merely a hint, and hence the read
may race with the actual teardown of XDP resources on the device. This
may change in the future, e.g. operations taking a reference on the XDP
resources of the driver, and in turn inhibiting turning off this flag.
However, for now, it can only be used as a hint to check whether device
supports becoming a redirection target.
Turn 'hw-offload' feature flag on for:
- netronome (nfp)
- netdevsim.
Turn 'native' and 'zerocopy' features flags on for:
- intel (i40e, ice, ixgbe, igc)
- mellanox (mlx5).
- stmmac
- netronome (nfp)
Turn 'native' features flags on for:
- amazon (ena)
- broadcom (bnxt)
- freescale (dpaa, dpaa2, enetc)
- funeth
- intel (igb)
- marvell (mvneta, mvpp2, octeontx2)
- mellanox (mlx4)
- mtk_eth_soc
- qlogic (qede)
- sfc
- socionext (netsec)
- ti (cpsw)
- tap
- tsnep
- veth
- xen
- virtio_net.
Turn 'basic' (tx, pass, aborted and drop) features flags on for:
- netronome (nfp)
- cavium (thunder)
- hyperv.
Turn 'redirect_target' feature flag on for:
- amanzon (ena)
- broadcom (bnxt)
- freescale (dpaa, dpaa2)
- intel (i40e, ice, igb, ixgbe)
- ti (cpsw)
- marvell (mvneta, mvpp2)
- sfc
- socionext (netsec)
- qlogic (qede)
- mellanox (mlx5)
- tap
- veth
- virtio_net
- xen
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Co-developed-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Marek Majtyka <alardam@gmail.com>
Link: https://lore.kernel.org/r/3eca9fafb308462f7edb1f58e451d59209aa07eb.1675245258.git.lorenzo@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
The driver can be trivially converted, as it only triggers the gpio
pin briefly to do a reset, and it already only supports DT.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure that xdp_do_flush() is always executed before
napi_complete_done(). This is important for two reasons. First, a
redirect to an XSKMAP assumes that a call to xdp_do_redirect() from
napi context X on CPU Y will be followed by a xdp_do_flush() from the
same napi context and CPU. This is not guaranteed if the
napi_complete_done() is executed before xdp_do_flush(), as it tells
the napi logic that it is fine to schedule napi context X on another
CPU. Details from a production system triggering this bug using the
veth driver can be found following the first link below.
The second reason is that the XDP_REDIRECT logic in itself relies on
being inside a single NAPI instance through to the xdp_do_flush() call
for RCU protection of all in-kernel data structures. Details can be
found in the second link below.
Fixes: d678be1dc1 ("dpaa2-eth: add XDP_REDIRECT support")
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20221220185903.1105011-1-sbohrer@cloudflare.com
Link: https://lore.kernel.org/all/20210624160609.292325-1-toke@redhat.com/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Make sure that xdp_do_flush() is always executed before
napi_complete_done(). This is important for two reasons. First, a
redirect to an XSKMAP assumes that a call to xdp_do_redirect() from
napi context X on CPU Y will be followed by a xdp_do_flush() from the
same napi context and CPU. This is not guaranteed if the
napi_complete_done() is executed before xdp_do_flush(), as it tells
the napi logic that it is fine to schedule napi context X on another
CPU. Details from a production system triggering this bug using the
veth driver can be found following the first link below.
The second reason is that the XDP_REDIRECT logic in itself relies on
being inside a single NAPI instance through to the xdp_do_flush() call
for RCU protection of all in-kernel data structures. Details can be
found in the second link below.
Fixes: a1e031ffb4 ("dpaa_eth: add XDP_REDIRECT support")
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20221220185903.1105011-1-sbohrer@cloudflare.com
Link: https://lore.kernel.org/all/20210624160609.292325-1-toke@redhat.com/
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The pMAC (ENETC_PFPMR_PMACE) is probably unconditionally enabled in the
enetc driver to allow RX of preemptible packets and not see them as
error frames. I don't know why TX preemption (ENETC_MMCSR_ME) is enabled
though. With no way to say which traffic classes are preemptible (all
are express by default), no preemptible frames would be transmitted
anyway.
Lastly, it may have been believed that the register write lock-step mode
(now deleted) needed the pMAC to be enabled at all times. I don't know
if that's true. However, I've checked that driver writes to PM1
registers do propagate through to the ENETC IP even when the pMAC is
disabled.
With such incomplete support for frame preemption, it's best to just
remove whatever exists right now and come with something more coherent
later.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the enetc driver duplicates its writes to the PM0 registers
also to PM1, but it doesn't do this consistently - for example we write
to ENETC_PM0_MAXFRM but not to ENETC_PM1_MAXFRM.
Create enetc_port_mac_wr() which writes both the PM0 and PM1 register
with the same value (if frame preemption is supported on this port).
Also create enetc_port_mac_rd() which reads from PM0 - the assumption
being that PM1 contains just the same value.
This will be necessary when we enable the MAC Merge layer properly, and
the pMAC becomes operational.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MWLM bit (MAC write lock-step mode) allows register writes to the
pMAC to be auto-performed whenever the corresponding eMAC register is
written by the driver. This allows their configuration to remain
in sync.
The driver has set this bit since the initial commit, but it doesn't do
anything, since the hardware feature doesn't work (and the bit has been
removed from more recent versions of the documentation).
The driver does attempt, more or less, to keep those MAC registers in
sync by writing the same value once to e.g. ENETC_PM0_CMD_CFG (eMAC) and
once to ENETC_PM1_CMD_CFG (pMAC). Because the lockstep feature doesn't
work, that's what it will stick to.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a preliminary patch which replaces the hardcoded 0x1000 present
in other PM1 (port MAC 1, aka pMAC) register definitions, which is an
offset to the PM0 (port MAC 0, aka eMAC) equivalent register.
This definition will be used in more places by future code.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to other TSN features, query the Station Interface capability
register to see whether preemption is supported on this port or not.
On LS1028A, preemption is available on ports 0 and 2, but not on 1
and 3.
This will allow us in the future to write the pMAC registers only on the
ENETC ports where a pMAC actually exists.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The build system is complaining about the following:
enetc.o is added to multiple modules: fsl-enetc fsl-enetc-vf
enetc_cbdr.o is added to multiple modules: fsl-enetc fsl-enetc-vf
enetc_ethtool.o is added to multiple modules: fsl-enetc fsl-enetc-vf
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
