Next step towards HMM support. For now just silence the retry fault and
optionally redirect the request to the dummy page.
v2: make sure the VM is not destroyed while we handle the fault.
v3: fix VM destroy check, cleanup comments
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move the ASIC specific code into a new callback function.
v2: mask the flags for SI and CIK instead of a BUG_ON().
v3: remove last missed BUG_ON().
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Unify how we map the UAPI flags to the PTE hardware flags for a mapping.
Only the MTYPE is actually ASIC dependent, all other flags should be
copied over 1 to 1 and ASIC differences are handled later on.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
amdgpu_gmc_ras_late_init is used to init gmc specfic
ras debugfs/sysfs node and gmc specific interrupt handler.
It can be shared among gmc generations.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Problem:
Under certain conditions, when some IP bocks take a RAS error,
we can get into a situation where a GPU reset is not possible
due to issues in RAS in SMU/PSP.
Temporary fix until proper solution in PSP/SMU is ready:
When uncorrectable error happens the DF will unconditionally
broadcast error event packets to all its clients/slave upon
receiving fatal error event and freeze all its outbound queues,
err_event_athub interrupt will be triggered.
In such case and we use this interrupt
to issue GPU reset. THe GPU reset code is modified for such case to avoid HW
reset, only stops schedulers, deatches all in progress and not yet scheduled
job's fences, set error code on them and signals.
Also reject any new incoming job submissions from user space.
All this is done to notify the applications of the problem.
v2:
Extract amdgpu_amdkfd_pre/post_reset from amdgpu_device_lock/unlock_adev
Move amdgpu_job_stop_all_jobs_on_sched to amdgpu_job.c
Remove print param from amdgpu_ras_query_error_count
v3:
Update based on prevoius bug fixing patch to properly call amdgpu_amdkfd_pre_reset
for other XGMI hive memebers.
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The GRBM register interface is now capable of bursting 1 cycle per
register wr->wr, wr->rd much faster than previous muticycle per
transaction done interface. This has caused a problem where status
registers requiring HW to update have a 1 cycle delay, due to the
register update having to go through GRBM.
SW may operate on an incorrect value if they write a register and
immediately check the corresponding status register.
Registers requiring HW to clear or set fields may be delayed by 1 cycle.
For example,
1. write VM_INVALIDATE_ENG0_REQ mask = 5a
2. read VM_INVALIDATE_ENG0_ACK till the ack is same as the request mask = 5a
a. HW will reset VM_INVALIDATE_ENG0_ACK = 0 until invalidation is complete
3. write VM_INVALIDATE_ENG0_REQ mask = 5a
4. read VM_INVALIDATE_ENG0_ACK till the ack is same as the request mask = 5a
a. First read of VM_INVALIDATE_ENG0_ACK = 5a instead of 0
b. Second read of VM_INVALIDATE_ENG0_ACK = 0 because
the remote GRBM h/w register takes one extra cycle to be cleared
c. In this case, SW will see a false ACK if they exit on first read
Affected registers (only GC variant) | Recommended Dummy Read
--------------------------------------+----------------------------
VM_INVALIDATE_ENG*_ACK | VM_INVALIDATE_ENG*_REQ
VM_L2_STATUS | VM_L2_STATUS
VM_L2_PROTECTION_FAULT_STATUS | VM_L2_PROTECTION_FAULT_STATUS
VM_L2_PROTECTION_FAULT_ADDR_HI/LO32 | VM_L2_PROTECTION_FAULT_ADDR_HI/LO32
VM_L2_IH_LOG_BUSY | VM_L2_IH_LOG_BUSY
MC_VM_L2_PERFCOUNTER_HI/LO | MC_VM_L2_PERFCOUNTER_HI/LO
ATC_L2_PERFCOUNTER_HI/LO | ATC_L2_PERFCOUNTER_HI/LO
ATC_L2_PERFCOUNTER2_HI/LO | ATC_L2_PERFCOUNTER2_HI/LO
Signed-off-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Reviewed-by: Jack Xiao <Jack.Xiao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is for kfd to reuse amdgpu TLB invalidation function.
On gfx10, kfd only needs to flush TLB on gfx hub but not
on mm hub. So export a function for KFD flush TLB only on
specific hub.
Signed-off-by: Oak Zeng <Oak.Zeng@amd.com>
Reviewed-by: Christian Konig <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use dma_set_mask_and_coherent to set both masks in one go, and remove
the no longer required fallback, as the kernel now always accepts
larger than required DMA masks. Fail the driver probe if we can't
set the DMA mask, as that means the system can only support a larger
mask.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Untie the bind of get/set athub CG state from mmhub, for cosmetic fix and Asic
not using mmhub 1.0. Besides, also fix wrong athub CG state in amdgpu_pm_info.
Signed-off-by: Le Ma <le.ma@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
ce can also trigger interrupt, and even both ce and ue error can be
found in one ras query, distinguishing between ce and ue in interrupt
handler is uncessary.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Suggested-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
we only read error information for correctable error in interrupt
handler, gpu reset is unnecessary since there is no data lost
in correctable error
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
we can simplify all those unnecessary function under
SRIOV for vega10 since:
1) PSP L1 policy is by force enabled in SRIOV
2) original logic always set all flags which make itself
a dummy step
besides,
1) the ih_doorbell_range set should also be skipped
for VEGA10 SRIOV.
2) the gfx_common registers should also be skipped
for VEGA10 SRIOV.
Signed-off-by: Monk Liu <Monk.Liu@amd.com>
Reviewed-by: Emily Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
With the printing, we don't need to parse the value on our own any more.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Any dce register read back from arct is invalid. use hard code
stolen memory for arct until we validate the s3.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Le Ma <Le.Ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Maarten needs -rc4 backmerged so he can pull in the fbcon notifier
removal topic branch into drm-misc-next.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
