The size of the mux stride was off by one, which could result in
invalid pin configuration on the device side or invalid state
readings on the software side.
While on it also update the code and:
- Increase the mux stride size to 16
- Align the virtual muxed regmap range to 16
- Start the regmap window at the selector
- Mark reserved registers as not-readable
Fixes: 8670de9fae ("pinctrl: cy8c95x0: Use regmap ranges")
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reported-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/20240902072859.583490-1-patrick.rudolph@9elements.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
intel-pinctrl for v6.11-1
This includes a new ACPI ID that is added to the Intel Meteor Lake
driver to support recent Intel Arrow Lake hardware.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On X1E80100, GPIO interrupts for wakeup-capable pins have been broken since
the introduction of the pinctrl driver. This prevents keyboard and touchpad
from working on most of the X1E laptops. So far we have worked around this
by manually building a kernel with the "wakeup-parent" removed from the
pinctrl node in the device tree, but we cannot expect all users to do that.
Implement a similar workaround in the driver by clearing the wakeirq_map
for X1E80100. This avoids using the PDC wakeup parent for all GPIOs
and handles the interrupts directly in the pinctrl driver instead.
The PDC driver needs additional changes to support X1E80100 properly.
Adding a workaround separately first allows to land the necessary PDC
changes through the normal release cycle, while still solving the more
critical problem with keyboard and touchpad on the current stable kernel
versions. Bypassing the PDC is enough for now, because we have not yet
enabled the deep idle states where using the PDC becomes necessary.
Cc: stable@vger.kernel.org
Fixes: 05e4941d97 ("pinctrl: qcom: Add X1E80100 pinctrl driver")
Signed-off-by: Stephan Gerhold <stephan.gerhold@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konradybcio@kernel.org>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/20240830-x1e80100-bypass-pdc-v1-1-d4c00be0c3e3@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The base iomux offsets for each GPIO pin line are accumulatively
calculated based off iomux width flag in rockchip_pinctrl_get_soc_data.
If the iomux width flag is one of IOMUX_WIDTH_4BIT, IOMUX_WIDTH_3BIT or
IOMUX_WIDTH_2BIT, the base offset for next pin line would increase by 8
bytes, otherwise it would increase by 4 bytes.
Despite most of GPIO2-B iomux have 2-bit data width, which can be fit
into 4 bytes space with write mask, it actually take 8 bytes width for
whole GPIO2-B line.
Commit e8448a6c81 ("pinctrl: rockchip: fix pinmux bits for RK3328
GPIO2-B pins") wrongly set iomux width flag to 0, causing all base
iomux offset for line after GPIO2-B to be calculated wrong. Fix the
iomux width flag to IOMUX_WIDTH_2BIT so the offset after GPIO2-B is
correctly increased by 8, matching the actual width of GPIO2-B iomux.
Fixes: e8448a6c81 ("pinctrl: rockchip: fix pinmux bits for RK3328 GPIO2-B pins")
Cc: stable@vger.kernel.org
Reported-by: Richard Kojedzinszky <richard@kojedz.in>
Closes: https://lore.kernel.org/linux-rockchip/4f29b743202397d60edfb3c725537415@kojedz.in/
Tested-by: Richard Kojedzinszky <richard@kojedz.in>
Signed-off-by: Huang-Huang Bao <i@eh5.me>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Trevor Woerner <twoerner@gmail.com>
Link: https://lore.kernel.org/20240709105428.1176375-1-i@eh5.me
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Despite its name, commit fed74d7527 ("pinctrl: mediatek: common-v2:
Fix bias-disable for PULL_PU_PD_RSEL_TYPE") actually broke bias-disable
for PULL_PU_PD_RSEL_TYPE.
mtk_pinconf_bias_set_combo() tries every bias method supported by the
pin until one succeeds. For PULL_PU_PD_RSEL_TYPE pins, before the
breaking commit, mtk_pinconf_bias_set_rsel() would be called first to
try and set the RSEL value (as well as PU and PD), and if that failed,
the only other valid option was that bias-disable was specified, which
would then be handled by calling mtk_pinconf_bias_set_pu_pd() and
disabling both PU and PD.
The breaking commit misunderstood this logic and added an early "return
0" in mtk_pinconf_bias_set_rsel(). The result was that in the
bias-disable case, the bias was left unchanged, since by returning
success, mtk_pinconf_bias_set_combo() no longer tried calling
mtk_pinconf_bias_set_pu_pd() to disable the bias.
Since the logic for configuring bias-disable on PULL_PU_PD_RSEL_TYPE
pins required mtk_pinconf_bias_set_rsel() to fail first, in that case,
an error was printed to the log, eg:
mt8195-pinctrl 10005000.pinctrl: Not support rsel value 0 Ohm for pin = 29 (GPIO29)
This is what the breaking commit actually got rid of, and likely part of
the reason why that commit was thought to be fixing functionality, while
in reality it was breaking it.
Instead of simply reverting that commit, restore the functionality but
in a way that avoids the error from being printed and makes the code
less confusing:
* Return 0 explicitly if a bias method was successful
* Introduce an extra function mtk_pinconf_bias_set_pu_pd_rsel() that
calls both mtk_pinconf_bias_set_rsel() (only if needed) and
mtk_pinconf_bias_set_pu_pd()
* And analogously for the corresponding getters
Fixes: fed74d7527 ("pinctrl: mediatek: common-v2: Fix bias-disable for PULL_PU_PD_RSEL_TYPE")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/20240808-mtk-rsel-bias-disable-fix-v1-1-1b4e85bf596c@collabora.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl-at91 currently does not support the gpio-groups devicetree
property and has no pin-range.
Because of this at91 gpios stopped working since patch
commit 2ab73c6d83 ("gpio: Support GPIO controllers without pin-ranges")
This was discussed in the patches
commit fc328a7d1f ("gpio: Revert regression in sysfs-gpio (gpiolib.c)")
commit 56e337f2cf ("Revert "gpio: Revert regression in sysfs-gpio (gpiolib.c)"")
As a workaround manually set pin-range via gpiochip_add_pin_range() until
a) pinctrl-at91 is reworked to support devicetree gpio-groups
b) another solution as mentioned in
commit 56e337f2cf ("Revert "gpio: Revert regression in sysfs-gpio (gpiolib.c)"")
is found
Signed-off-by: Thomas Blocher <thomas.blocher@ek-dev.de>
Link: https://lore.kernel.org/5b992862-355d-f0de-cd3d-ff99e67a4ff1@ek-dev.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Intel Arrow Lake-H/U has the same GPIO hardware than Meteor Lake-P but
the ACPI ID is different. Add this new ACPI ID to the list of supported
devices.
Cc: stable@vger.kernel.org
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The of_property_for_each_u32() macro needs five parameters, two of which
are primarily meant as internal variables for the macro itself (in the
for() clause). Yet these two parameters are used by a few drivers, and this
can be considered misuse or at least bad practice.
Now that the kernel uses C11 to build, these two parameters can be avoided
by declaring them internally, thus changing this pattern:
struct property *prop;
const __be32 *p;
u32 val;
of_property_for_each_u32(np, "xyz", prop, p, val) { ... }
to this:
u32 val;
of_property_for_each_u32(np, "xyz", val) { ... }
However two variables cannot be declared in the for clause even with C11,
so declare one struct that contain the two variables we actually need. As
the variables inside this struct are not meant to be used by users of this
macro, give the struct instance the noticeable name "_it" so it is visible
during code reviews, helping to avoid new code to use it directly.
Most usages are trivially converted as they do not use those two
parameters, as expected. The non-trivial cases are:
- drivers/clk/clk.c, of_clk_get_parent_name(): easily doable anyway
- drivers/clk/clk-si5351.c, si5351_dt_parse(): this is more complex as the
checks had to be replicated in a different way, making code more verbose
and somewhat uglier, but I refrained from a full rework to keep as much
of the original code untouched having no hardware to test my changes
All the changes have been build tested. The few for which I have the
hardware have been runtime-tested too.
Reviewed-by: Andre Przywara <andre.przywara@arm.com> # drivers/clk/sunxi/clk-simple-gates.c, drivers/clk/sunxi/clk-sun8i-bus-gates.c
Acked-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org> # drivers/gpio/gpio-brcmstb.c
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> # drivers/irqchip/irq-atmel-aic-common.c
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # drivers/iio/adc/ti_am335x_adc.c
Acked-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com> # drivers/pwm/pwm-samsung.c
Acked-by: Richard Leitner <richard.leitner@linux.dev> # drivers/usb/misc/usb251xb.c
Acked-by: Mark Brown <broonie@kernel.org> # sound/soc/codecs/arizona.c
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com> # sound/soc/codecs/arizona.c
Acked-by: Michael Ellerman <mpe@ellerman.id.au> # arch/powerpc/sysdev/xive/spapr.c
Acked-by: Stephen Boyd <sboyd@kernel.org> # clk
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Acked-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20240724-of_property_for_each_u32-v3-1-bea82ce429e2@bootlin.com
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Pull pin control updates from Linus Walleij:
"Some new drivers is the main part, the rest is cleanups and nonurgent
fixes.
Nothing much special about this, no core changes this time.
New drivers:
- Renesas RZ/V2H(P) SoC
- NXP Freescale i.MX91 SoC
- Nuvoton MA35D1 SoC
- Qualcomm PMC8380, SM4250, SM4250 LPI
Enhancements:
- A slew of scoped-based simplifications of of_node_put()"
* tag 'pinctrl-v6.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (110 commits)
pinctrl: renesas: rzg2l: Support output enable on RZ/G2L
pinctrl: renesas: rzg2l: Clean up and refactor OEN read/write functions
pinctrl: renesas: rzg2l: Clarify OEN read/write support
dt-bindings: pinctrl: pinctrl-single: Fix pinctrl-single,gpio-range description
dt-bindings: pinctrl: npcm8xx: add missing pin group and mux function
dt-bindings: pinctrl: pinctrl-single: fix schmitt related properties
pinctrl: freescale: Use scope based of_node_put() cleanups
pinctrl: equilibrium: Use scope based of_node_put() cleanups
pinctrl: ti: iodelay: Use scope based of_node_put() cleanups
pinctrl: qcom: lpass-lpi: increase MAX_NR_GPIO to 32
pinctrl: cy8c95x0: Update cache modification
pinctrl: cy8c95x0: Use cleanup.h
pinctrl: renesas: r8a779h0: Remove unneeded separators
pinctrl: renesas: r8a779g0: Add INTC-EX pins, groups, and function
pinctrl: renesas: r8a779g0: Remove unneeded separators
pinctrl: renesas: r8a779h0: Add AVB MII pins and groups
pinctrl: renesas: r8a779g0: Fix TPU suffixes
pinctrl: renesas: r8a779g0: Fix TCLK suffixes
pinctrl: renesas: r8a779g0: FIX PWM suffixes
pinctrl: renesas: r8a779g0: Fix IRQ suffixes
...
Pull gpio updates from Bartosz Golaszewski:
"The majority of added lines are two new modules: the GPIO virtual
consumer module that improves our ability to add automated tests for
the kernel API and the "sloppy" logic analyzer module that uses the
GPIO API to implement a coarse-grained debugging tool for useful for
remote development.
Other than that we have the usual assortment of various driver
extensions, improvements to the core GPIO code, DT-bindings and other
documentation updates as well as an extension to the interrupt
simulator:
GPIOLIB core:
- rework kfifo handling rework in the character device code
- improve the labeling of GPIOs requested as interrupts and show more
info on interrupt-only GPIOs in debugfs
- remove unused APIs
- unexport interfaces that are only used from the core GPIO code
- drop the return value from gpiochip_set_desc_names() as it cannot
fail
- move a string array definition out of a header and into a specific
compilation unit
- convert the last user of gpiochip_get_desc() other than GPIO core
to using a safer alternative
- use array_index_nospec() where applicable
New drivers:
- add a "virtual GPIO consumer" module that allows requesting GPIOs
from actual hardware and driving tests of the in-kernel GPIO API
from user-space over debugfs
- add a GPIO-based "sloppy" logic analyzer module useful for "first
glance" debugging on remote boards
Driver improvements:
- add support for a new model to gpio-pca953x
- lock GPIOs as interrupts in gpio-sim when the lines are requested
as irqs via the simulator domain + some other minor improvements
- improve error reporting in gpio-syscon
- convert gpio-ath79 to using dynamic GPIO base and range
- use pcibios_err_to_errno() for converting PCIBIOS error codes to
errno vaues in gpio-amd8111 and gpio-rdc321x
- allow building gpio-brcmstb for the BCM2835 architecture
DT bindings:
- convert DT bindings for lsi,zevio, mpc8xxx, and atmel to DT schema
- document new properties for aspeed,gpio, fsl,qoriq-gpio and
gpio-vf610
- document new compatibles for pca953x and fsl,qoriq-gpio
Documentation:
- document stricter behavior of the GPIO character device uAPI with
regards to reconfiguring requested line without direction set
- clarify the effect of the active-low flag on line values and edges
- remove documentation for the legacy GPIO API in order to stop
tempting people to use it
- document the preference for using pread() for reading edge events
in the sysfs API
Other:
- add an extended initializer to the interrupt simulator allowing to
specify a number of callbacks callers can use to be notified about
irqs being requested and released"
* tag 'gpio-updates-for-v6.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (41 commits)
gpio: mc33880: Convert comma to semicolon
gpio: virtuser: actually use the "trimmed" local variable
dt-bindings: gpio: convert Atmel GPIO to json-schema
gpio: virtuser: new virtual testing driver for the GPIO API
dt-bindings: gpio: vf610: Allow gpio-line-names to be set
gpio: sim: lock GPIOs as interrupts when they are requested
genirq/irq_sim: add an extended irq_sim initializer
dt-bindings: gpio: fsl,qoriq-gpio: Add compatible string fsl,ls1046a-gpio
gpiolib: unexport gpiochip_get_desc()
gpio: add sloppy logic analyzer using polling
Documentation: gpio: Reconfiguration with unset direction (uAPI v2)
Documentation: gpio: Reconfiguration with unset direction (uAPI v1)
dt-bindings: gpio: fsl,qoriq-gpio: add common property gpio-line-names
gpio: ath79: convert to dynamic GPIO base allocation
pinctrl: da9062: replace gpiochip_get_desc() with gpio_device_get_desc()
gpiolib: put gpio_suffixes in a single compilation unit
Documentation: gpio: Clarify effect of active low flag on line edges
Documentation: gpio: Clarify effect of active low flag on line values
gpiolib: Remove data-less gpiochip_add() function
gpio: sim: use devm_mutex_init()
...
On the RZ/G2L SoC family, the direction of the Ethernet TXC/TX_CLK
signal is selectable to support an Ethernet PHY operating in either MII
or RGMII mode. By default, the signal is configured as an input and MII
mode is supported. The ETH_MODE register can be modified to configure
this signal as an output to support RGMII mode.
As this signal is by default an input, and can optionally be switched to
an output, it maps neatly onto an `output-enable` property in the device
tree.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20240625200316.4282-4-paul.barker.ct@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The variable naming in the various OEN functions has been confusing. We
were passing the _pin & bit variables from rzg2l_pinctrl_pinconf_get()
and rzg2l_pinctrl_pinconf_set() as the offset & pin argument to the
oen_read() and oen_write() functions. This doesn't make sense, the first
of these isn't actually an offset and the second is not needed for
RZ/V2H but leads to confusion with the bit variable used within these
functions.
To tidy this up, instead pass the _pin variable directly to the
oen_read() and oen_write() functions with consistent naming. Then
rzg3s_read_oen() and rzg3s_write_oen() can use macros to get the port
and pin numbers it needs.
Instead of passing the pin capabilities into oen_read() and oen_write(),
check that the pin supports OEN before calling these functions.
Also, merge rzg3s_oen_is_supported() into rzg3s_pin_to_oen_bit() to give
a single translation function which returns an error if the pin doesn't
support OEN. While we're here, remove an unnecessary branch and clarify
the variable naming. Lastly, check that we are not dealing with a
dedicated pin before calling RZG2L_PIN_ID_TO_{PORT,PIN}().
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20240625200316.4282-3-paul.barker.ct@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
We currently support OEN read/write for the RZ/G3S SoC but not the
RZ/G2L SoC family (consisting of RZ/G2L, RZ/G2LC, RZ/G2UL, RZ/V2L &
RZ/Five). The appropriate functions are renamed to clarify this and to
match the callback names.
We should also only set the oen_read and oen_write function pointers for
the devices which support these operations. This requires us to check
that these function pointers are valid before calling them.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20240625200316.4282-2-paul.barker.ct@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Pin Multiplex attachment in Rev.1.10 of the R-Car V4H Series
Hardware User's Manual still has two alternate pins named both TCLK3
and TCLK4. To differentiate, the pin control driver uses "TCLK[34]" and
"TCLK[34]_X". In addition, there are alternate pins without suffix, and
with an "_A" or "_B" suffix.
Increase uniformity by adopting R-Car V4M naming:
- Rename "TCLK2_B" to "TCLK2_C",
- Rename "TCLK[12]_A" to "TCLK[12]_B",
- Rename "TCLK[12]" to "TCLK[12]_A",
- Rename "TCLK[34]_A" to "TCLK[34]_C",
- Rename "TCLK[34]_X" to "TCLK[34]_A",
- Rename "TCLK[34]" to "TCLK[34]_B".
Fixes: ad9bb2fec6 ("pinctrl: renesas: Initial R8A779G0 (R-Car V4H) PFC support")
Fixes: 0df46188a5 ("pinctrl: renesas: r8a779g0: Add missing TCLKx_A/TCLKx_B/TCLKx_X")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/2845ff1f8fe1fd8d23d2f307ad5e8eb8243da608.1717754960.git.geert+renesas@glider.be
The suffixes of the IRQ identifiers for external interrupts 0-3
are inconsistent:
- "IRQ0" and "IRQ0_A",
- "IRQ1" and "IRQ1_A",
- "IRQ2" and "IRQ2_A",
- "IRQ3" and "IRQ3_B".
The suffixes for external interrupts 4 and 5 do follow conventional
naming:
- "IRQ4A" and IRQ4_B",
- "IRQ5".
Fix this by adopting R-Car V4M naming:
- Rename "IRQ[0-2]_A" to "IRQ[0-2]_B",
- Rename "IRQ[0-3]" to "IRQ[0-3]_A".
Fixes: ad9bb2fec6 ("pinctrl: renesas: Initial R8A779G0 (R-Car V4H) PFC support")
Fixes: 1b23d8a478 ("pinctrl: renesas: r8a779g0: Add missing IRQx_A/IRQx_B")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/8ce9baf0a0f9346544a3ac801fd962c7c12fd247.1717754960.git.geert+renesas@glider.be
(H)SCIF instance 3 has two alternate pin groups: "hscif3" and
"hscif3_a", resp. "scif3" and "scif3_a", but the actual meanings of the
pins within the groups do not match.
Increase uniformity by adopting R-Car V4M naming:
- Rename "hscif3_a" to "hscif3_b",
- Rename "hscif3" to "hscif3_a",
- Rename "scif3" to "scif3_b".
While at it, remove unneeded separators.
Fixes: ad9bb2fec6 ("pinctrl: renesas: Initial R8A779G0 (R-Car V4H) PFC support")
Fixes: 050442ae4c ("pinctrl: renesas: r8a779g0: Add pins, groups and functions")
Fixes: 213b713255 ("pinctrl: renesas: r8a779g0: Add missing HSCIF3_A")
Fixes: 49e4697656 ("pinctrl: renesas: r8a779g0: Add missing SCIF3")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/61fdde58e369e8070ffd3c5811c089e6219c7ecc.1717754960.git.geert+renesas@glider.be
The Pin Multiplex attachment in Rev.1.10 of the R-Car V4H Series
Hardware User's Manual still has two alternate pin groups (GP0_14-18
and GP1_6-10) each named both HSCIF1 and SCIF1. To differentiate, the
pin control driver uses "(h)scif1" and "(h)scif1_x", which were
considered temporary names until the conflict was sorted out.
Fix this by adopting R-Car V4M naming:
- Rename "(h)scif1" to "(h)scif1_a",
- Rename "(h)scif1_x" to "(h)scif1_b".
Adopt the R-Car V4M naming "(h)scif1_a" and "(h)scif1_b" to increase
uniformity.
While at it, remove unneeded separators.
Fixes: ad9bb2fec6 ("pinctrl: renesas: Initial R8A779G0 (R-Car V4H) PFC support")
Fixes: 050442ae4c ("pinctrl: renesas: r8a779g0: Add pins, groups and functions")
Fixes: cf4f789184 ("pinctrl: renesas: r8a779g0: Add missing HSCIF1_X")
Fixes: 9c151c2be9 ("pinctrl: renesas: r8a779g0: Add missing SCIF1_X")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/5009130d1867e12abf9b231c8838fd05e2b28bee.1717754960.git.geert+renesas@glider.be
The Pin Multiplex attachment in Rev.1.10 of the R-Car V4H Series
Hardware User's Manual still has two alternate pins named both
"FXR_TXEN[AB]". To differentiate, the pin control driver uses
"FXR_TXEN[AB]" and "FXR_TXEN[AB]_X", which were considered temporary
names until the conflict was sorted out.
Fix this by adopting R-Car V4M naming:
- Rename "FXR_TXEN[AB]" to "FXR_TXEN[AB]_A",
- Rename "FXR_TXEN[AB]_X" to "FXR_TXEN[AB]_B".
Fixes: ad9bb2fec6 ("pinctrl: renesas: Initial R8A779G0 (R-Car V4H) PFC support")
Fixes: 1c2646b5ce ("pinctrl: renesas: r8a779g0: Add missing FlexRay")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/5e1e9abb46c311d4c54450d991072d6d0e66f14c.1717754960.git.geert+renesas@glider.be
