The SoM cannot be used standalone, this compatible is invalid and it is
always overwritten when this .dtsi file is included, remove it
therefore.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to fsl,dspi.yaml the expected order for describing the dmas
and dma-names properties is "tx" first, followed by "rx".
Adjust it acordingly to fix the following dt-schema warnings:
spi@4002c000: dma-names:0: 'tx' was expected
spi@4002c000: dma-names:1: 'rx' was expected
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently, the compatible string used for the spidev device is "lwn,bk4",
which is the same as the board compatible string documented at fsl.yaml.
This causes several dt-schema warnings:
make dtbs_check DT_SCHEMA_FILES=fsl.yaml
...
['lwn,bk4'] is too short
'lwn,bk4' is not one of ['tq,imx8dxp-tqma8xdp-mba8xx']
'lwn,bk4' is not one of ['tq,imx8qxp-tqma8xqp-mba8xx']
'lwn,bk4' is not one of ['armadeus,imx1-apf9328', 'fsl,imx1ads']
Use a more specific "lwn,bk4-spi" compatible string to fix the problem.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Bindings expect GPIO hog names to end with 'hog' suffix, so correct it
to fix dtbs_check warning:
vf610-zii-dev-rev-c.dtb: eth0_intrp: $nodename:0: 'eth0_intrp' does not match '^.+-hog(-[0-9]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to fsl,sec-v4.0.yaml, the job ring node names
should be 'jr'.
Change them to fix the following dt-schema warnings:
crypto@400f0000: 'jr0@1000', 'jr1@2000' do not match any of the regexes:
'^jr@[0-9a-f]+$', '^rtic@[0-9a-f]+$', 'pinctrl-[0-9]+'
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix some errors in the Marvell MV88E6xxx switch descriptions:
- switch0@0 is not OK, should be ethernet-switch@0
- ports should be ethernet-ports
- port should be ethernet-port
- phy should be ethernet-phy
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is no need to split dmas in two lines.
Make it more readable by writing it in a single line.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pass 'mmc' as the esdhc node names to fix the following schema
warnings:
vf610-cosmic.dtb: esdhc@400b1000: $nodename:0: 'esdhc@400b1000' does not match '^mmc(@.*)?$'
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Regulators should not be placed under simple-bus.
Move it outside simple-bus to fix the following schema warnings:
regulators: $nodename:0: 'regulators' does not match '^([a-z][a-z0-9\\-]+-bus|bus|localbus|soc|axi|ahb|apb)(@.+)?$'
From schema: site-packages/dtschema/schemas/simple-bus.yaml
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
