Associate the LED node name with the corresponding board silkscreen for
more precise identification. In fact, the board has a total of seven
LEDs, some of which are user-controllable (i. e. usr{1,2,3}), while
others are directly controlled by hardware (e. g. power, overcurrent,
...). All these LEDs are either green or red, so using the names
led-green and led-red for the two LEDs mapped in the DTS does not
simplify their identification on the board.
Moreover, this patch is a prerequisite for adding the usr3 LED, which
has not been included in the DTS.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://lore.kernel.org/r/20250217114513.1098844-1-dario.binacchi@amarulasolutions.com
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
During s2idle tests on the Raspberry CM4 the VPU firmware always crashes
on xHCI power-domain resume:
root@raspberrypi:/sys/power# echo freeze > state
[ 70.724347] xhci_suspend finished
[ 70.727730] xhci_plat_suspend finished
[ 70.755624] bcm2835-power bcm2835-power: Power grafx off
[ 70.761127] USB: Set power to 0
[ 74.653040] USB: Failed to set power to 1 (-110)
This seems to be caused because of the mixed usage of
raspberrypi-power and bcm2835-power at the same time. So avoid
the usage of the VPU firmware power-domain driver, which
prevents the VPU crash.
Fixes: 522c35e08b ("ARM: dts: bcm2711: Add BCM2711 xHCI support")
Link: https://github.com/raspberrypi/linux/issues/6537
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Link: https://lore.kernel.org/r/20250201112729.31509-1-wahrenst@gmx.net
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
WM8960 has the following power supplies:
- AVDD
- DBVDD
- DCVDD
- SPKVDD1
- SPKVDD2
Add new audio regulators to reflect the schematic and complete missed
power supplies.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
WM8960 has the following power supplies:
- AVDD
- DBVDD
- DCVDD
- SPKVDD1
- SPKVDD2
Add new audio regulators to reflect the schematic and complete missed
power supplies.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to leds-gpio.yaml, the LED nodes should not contain
unit addresses. Remove them.
Also, 'default-trigger' is not a valid property. Change it to
'linux,default-trigger'.
These changes fix the following dt-schema warnings:
led@1: Unevaluated properties are not allowed ('reg' was unexpected)
led@2: Unevaluated properties are not allowed ('reg' was unexpected)
led@3: Unevaluated properties are not allowed ('default-trigger', 'reg' were unexpected)
leds: '#address-cells', '#size-cells' do not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently, the compatible string used for the spidev device is "lwn,bk4",
which is the same as the board compatible string documented at fsl.yaml.
This causes several dt-schema warnings:
make dtbs_check DT_SCHEMA_FILES=fsl.yaml
...
['lwn,bk4'] is too short
'lwn,bk4' is not one of ['tq,imx8dxp-tqma8xdp-mba8xx']
'lwn,bk4' is not one of ['tq,imx8qxp-tqma8xqp-mba8xx']
'lwn,bk4' is not one of ['armadeus,imx1-apf9328', 'fsl,imx1ads']
Use a more specific "lwn,bk4-spi" compatible string to fix the problem.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The card name for ALSA is generated from the model name string and
is limited to 16 characters. Use a shorter name to prevent cutting the
name.
Since nearly all starter kit mainboards for i.MX based SoM by TQ-Systems
use the same codec with the same routing on board it is a good idea to
use the same mode name for the sound card. This allows sharing a default
asound.conf in BSP over all the kits.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The card name for ALSA is generated from the model name string and
is limited to 16 characters. Use a shorter name to prevent cutting the
name.
Since nearly all starter kit mainboards for i.MX based SoM by TQ-Systems
use the same codec with the same routing on board it is a good idea to
use the same mode name for the sound card. This allows sharing a default
asound.conf in BSP over all the kits.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The card name for ALSA is generated from the model name string and
is limited to 16 characters. Use a shorter name to prevent cutting the
name.
Since nearly all starter kit mainboards for i.MX based SoM by TQ-Systems
use the same codec with the same routing on board it is a good idea to
use the same mode name for the sound card. This allows sharing a default
asound.conf in BSP over all the kits.
Signed-off-by: Markus Niebel <Markus.Niebel@ew.tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
bootph-all as phase tag was added to dt-schema
(dtschema/schemas/bootph.yaml) to describe various node usage during
boot phases with DT. Add bootph-all for all nodes that are used in the
bootloader on Renesas R-Car Gen2 SoCs.
All SoC require CPG clock and its input clock, RST Reset, PFC pin
control and PRR ID register access during all stages of the boot
process, those are marked using bootph-all property, and so is the SoC
bus node which contains these IP.
Each board console UART is also marked as bootph-all to make it
available in all stages of the boot process.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/20250209180616.160253-1-marek.vasut+renesas@mailbox.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Bindings expect GPIO hog names to end with 'hog' suffix, so correct it
to fix dtbs_check warning:
vf610-zii-dev-rev-c.dtb: eth0_intrp: $nodename:0: 'eth0_intrp' does not match '^.+-hog(-[0-9]+)?$'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On the i.MX5 chips the peripheral interrupts are represented directly only
by their interrupt numbers.
The CCM nodes are not following this format and cause the following
dt-schema warnings:
ccm@73fd4000: interrupts: [[0], [71], [4], [0], [72], [4]] is too long
Fix it by passing only the two interrupt numbers.
Run-time tested in on an imx53-qsb board.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to fsl,sec-v4.0.yaml, the job ring node names
should be 'jr'.
Change them to fix the following dt-schema warnings:
crypto@400f0000: 'jr0@1000', 'jr1@2000' do not match any of the regexes:
'^jr@[0-9a-f]+$', '^rtic@[0-9a-f]+$', 'pinctrl-[0-9]+'
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The current solution for powering off the Apalis iMX6 is not functioning
as intended. To resolve this, it is necessary to power off the
vgen2_reg, which will also set the POWER_ENABLE_MOCI signal to a low
state. This ensures the carrier board is properly informed to initiate
its power-off sequence.
The new solution uses the regulator-poweroff driver, which will power
off the regulator during a system shutdown.
Cc: <stable@vger.kernel.org>
Fixes: 4eb56e26f9 ("ARM: dts: imx6q-apalis: Command pmic to standby for poweroff")
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to atmel,maxtouch.yaml, the correct property that describes
the GPIO connected to the touchscreen reset line is 'reset-gpios'.
Change it accordingly to fix the following dt-schema warning:
'reset-gpio' does not match any of the regexes: 'pinctrl-[0-9]+'
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The btt3 device' HW revisions from 0 to 2 use imx287 SoC and are to
some extend similar to already upstreamed XEA devices, hence are
using common imx28-lwe.dtsi file.
New, imx28-btt3.dtsi has been added to embrace common DTS
properties for different HW revisions for this device.
As a result - changes introduced in imx28-btt3-[012].dts are
minimal.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
