rn_vbios_smu_set_dprefclk() was added in 2019 by
commit 4edb6fc918 ("drm/amd/display: Add Renoir clock manager")
rv1_vbios_smu_set_dprefclk() was also added in 2019 by
commit dc88b4a684 ("drm/amd/display: make clk mgr soc specific")
neither have been used.
Remove them.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Due to very small clock register delta between DCN35 and DCN351, clock
spread is being checked on the wrong register for DCN351, causing the
display driver to believe that DPREFCLK downspread to be disabled when
in some stacks it is enabled. This causes the clock values for audio to
be incorrect.
[How]
Both DCN351 and DCN35 use the same clk_mgr, so we modify the DCN35
function that checks for SSC enable to read CLK6 instead of CLK5 when
using DCN351. This allows us to read for DPREFCLK downspread correctly
so the clock can properly compensate when setting values.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Kevin Gao <kevin.gao3@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We should never apply a minimum dispclk value while in
prepare_bandwidth or while displays are active. This is
always an optimizaiton for when all displays are disabled.
[HOW]
Defer dispclk optimization until safe_to_lower = true
and display_count reaches 0.
Since 0 has a special value in this logic (ie. no dispclk
required) we also need adjust the logic that clamps it for
the actual request to PMFW.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Chris Park <chris.park@amd.com>
Reviewed-by: Eric Yang <eric.yang@amd.com>
Signed-off-by: Jing Zhou <Jing.Zhou@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
dp_is_128b_132b_signal dereferences pipe->stream so it is necessary to
check it in advance.
Also fix erroneous spaces and move a variable declaration to top.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
These are left required changes for dio encoder refactor.
[HOW]
1. original logic is separated by config option
2. new link encoder dp enable/disable code for dcn35
3. process fec only for DP 8b10b encoding
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We should never apply a minimum dispclk value while in prepare_bandwidth
or while displays are active. This is always an optimization for when
all displays are disabled.
[How]
Defer dispclk optimization until safe_to_lower = true and display_count
reaches 0.
Since 0 has a special value in this logic (ie. no dispclk required)
we also need adjust the logic that clamps it for the actual request
to PMFW.
Reviewed-by: Gabe Teeger <gabe.teeger@amd.com>
Reviewed-by: Leo Chen <leo.chen@amd.com>
Reviewed-by: Syed Hassan <syed.hassan@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
On entering/exiting idle power, certain parameters would be
very useful to know for power profiling purposes.
[HOW]
This commit adds certain hard min clocks and pipe types
to log output on idle optimization enter/exit.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Sung Lee <Sung.Lee@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
When effective bandwidth from the SoC is enough to perform SubVP
prefetchs, then DF throttling is not required.
[HOW]
Provide SMU the required clocks for which DF throttling is not required.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Driver reports 0 display when the virtual display is still present, and
causes P-state hang in FW.
[HOW]
When enumerating through streams, check for active planes and use that
to indicate number of displays.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Daniel Sa <Daniel.Sa@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Setting min dispclk to 50Mhz outside clock lowering function causes
unnecessary calls to SMU to lower dispclk and causes dentist hangs when
there is no stream on the pipes.
[How]
Move the set minimum dispclk logic inside the lowering dispclk if
statement.
Fixes: 2344413205 ("DCN35 set min dispclk to 50Mhz")
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Nicholas Susanto <Nicholas.Susanto@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Skipping clock updates is not a hard requirement for overclocking
and only an optimization. Remove the skip as this can cause issues
for FAMS transitions during the overclock sequence. If FAMS
is enabled we must disable UCLK switch on any full update (which
requires update clocks to be called).
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
immediate_disable_crtc does not reset ODM. if switching to disable_crtc
which will disable ODM as well. i.e. need to restore ODM mem cfg at
reenable it at end of w/a.
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Xi (Alex) Liu <xi.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
Poniters, such as dc->clk_mgr, are null checked previously in the same
function, so Coverity warns "implies that "dc->clk_mgr" might be null".
As a result, these pointers need to be checked when used again.
This fixes 10 FORWARD_NULL issues reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This is a workaround for an dcn3.1 hang that happens if otg dispclk
is ramped while otg is on and stream enc is off.
But this w/a should not trigger when we have a dig active.
[How]
Avoid disable otg when dig FE/BE FIFO was not switched.
Acked-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Jingwen Zhu <jingwen.zhu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In OTG disable workarund, CRTC is disabled immediately
to improve performance, but this may cause timing issue
in DP HPO encoder FIFO and result in blank CRCs.
[How]
Replace the immediate CRTC disable call with normal disable call
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Xi (Alex) Liu <xi.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
Integer multiplies integer may overflow in context that expects an
expression of unsigned/siged long long (64 bits). This can be fixed
by casting integer to unsigned/siged long long to force 64 bits results.
This fixes 26 OVERFLOW_BEFORE_WIDEN issues reported by Coverity.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT]
1. is_pwrseq0 needs to check link before accessing link->link_index.
2. context is checked before accessing its bw_ctx.dml2
3. clk_mgr_base->bw_params is checked before clk_table.num_entries_per_cl
This fixes 4 REVERSE_INULL issues reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHAT & HOW]
clk_mgr_helper_get_active_display_cnt returns display count and itself
alone has no use.
This fixes 1 CHECKED_RETURN issue reported by Coverity.
Reviewed-by: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The null checks are redundant as they were already dereferenced
previously, as reported by Coverity; therefore the null checks
are removed.
This fixes 7 REVERSE_INULL issues reported by Coverity.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The null checks for ctx->dc_bios are redundant as it was already
dereferenced previously, as reported by Coverity; therefore the
null checks are removed.
This fixes 7 REVERSE_INULL issues reported by Coverity.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Tell the system about the current host router bandwidth to be used to
measure and calculate the right voltage to be used.
[how]
Send SMU message of each DPIA host router bandwidth.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Sung Joon Kim <sungjoon.kim@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On init if a display is connected, we need to maintain the DISPCLK
frequency Even though DPG_EN=1, the display still requires the correct
timing or it could cause audio corruption (if DISPCLK freq is reduced).
[How]
Read the current DISPCLK freq and request the same value to ensure the
timing is valid and unchanged.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Chris Park <chris.park@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
