[Why]
It seems HPD interrupts are enabled by default for all connectors, even
if the hpd source isn't valid. An eDP for example, does not have a valid
hpd source (but does have a valid hpdrx source; see construct_phy()).
Thus, eDPs should have their hpd interrupt disabled.
In the past, this wasn't really an issue. Although the driver gets
interrupted, then acks by writing to hw registers, there weren't any
subscribed handlers that did anything meaningful (see
register_hpd_handlers()).
But things changed with the introduction of IPS. s2idle requires that
the driver allows IPS for DMUB fw to put hw to sleep. Since register
access requires hw to be awake, the driver will block IPS entry to do
so. And no IPS means no hw sleep during s2idle.
This was the observation on DCN35 systems with an eDP. During suspend,
the eDP toggled its hpd pin as part of the panel power down sequence.
The driver was then interrupted, and acked by writing to registers,
blocking IPS entry.
[How]
Since DC marks eDP connections as having invalid hpd sources (see
construct_phy()), DM should disable them at the hw level. Do so in
amdgpu_dm_hpd_init() by disabling all hpd ints first, then selectively
enabling ones for connectors that have valid hpd sources.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Starting from 6.11, AMDGPU driver, while being loaded with amdgpu.dc=1,
due to lack of .is_two_pixels_per_container function in dce60_tg_funcs,
causes a NULL pointer dereference on PCs with old GPUs, such as R9 280X.
So this fix adds missing .is_two_pixels_per_container to dce60_tg_funcs.
Reported-by: Rosen Penev <rosenp@gmail.com>
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3942
Fixes: e6a901a008 ("drm/amd/display: use even ODM slice width for two pixels per container")
Signed-off-by: Aliaksei Urbanski <aliaksei.urbanski@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We advertise DCC as supported for NV12/P010 formats on GFX12,
but it would fail on this check on atomic commit.
Signed-off-by: David Rosca <david.rosca@amd.com>
Reviewed-by: Ruijing Dong <ruijing.dong@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Null pointer dereference issue could occur when pipe_ctx->plane_state
is null. The fix adds a check to ensure 'pipe_ctx->plane_state' is not
null before accessing. This prevents a null pointer dereference.
Found by code review.
Fixes: 3be5262e35 ("drm/amd/display: Rename more dc_surface stuff to plane_state")
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 63e6a77ccf)
Cc: stable@vger.kernel.org
drm_* macros are more helpful that DRM_* macros since the former
indicates the associated DRM device that prints the error, which maybe
helpful when debugging.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
print__rq_dlg_params_st() was added in 2017 by
commit 061bfa06a4 ("drm/amdgpu/display: Add dml support for DCN")
but has remained unused.
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
pre_surface_trace() has been unused since 2017's
commit 745cc746da ("drm/amd/display: remove
dc_pre_update_surfaces_to_stream from dc use")
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Upgrading the kernel may cause some systems that were previously not using
a firmware specified brightness curve to use one.
In the event of problems with this curve (for example an interpolation
error) add a new dcdebugmask value that can be used to turn it off. Also
add an info message to show that custom brightness curves are currently in
use.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Link: https://lore.kernel.org/r/20250228185145.186319-6-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This version brings along following fixes:
- Various cleanups to amdgpu dm
- Add DP tunneling IRQ handler
- Fix display corruption for dcn35
- Fix dmcub reset problem
- Adjust BW determination for PCON
- DIO encoder refactor
- Fix performance with SubVP under gaming
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
All cases except a failure to create a copy of the current context will
call dc_state_release() on the copied context.
Use a _free() macro to free the context and then adjust the error handling
flow to drop the unnecessary use of goto statements.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
USB4 DP BW Allocation uses DP_TUNNELING_IRQ to indicate the status update.
The DP_TUNNELING_IRQ is defined in LINK_SERVICE_IRQ_VECTOR_ESI0. When
receiving DP HPD IRQ in USB4, read the LINK_SERVICE_IRQ_VECTOR_ESI0.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Cruise Hung <Cruise.Hung@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
We want to add a visual confirm mode for DCC and MCache for
debugging purpose.
[HOW]
color pipes based on whether DCC is enabled and what MCache id
is used.
black - DCC disabled
red - DCC enabled
grey - 2 different MCaches used
other colors - 1 MCache used
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Leo Zeng <Leo.Zeng@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If we soft reset before halt finishes and there are outstanding
memory transactions then the memory interface may produce unexpected
results, such as out of order transactions when the firmware next runs.
These can manifest as random or unexpected load/store violations.
[How]
Increase the timeout before soft reset to ensure the DMCUB has quiesced.
This is effectively 1s maximum based on experimentation.
Use the enable bit check on DCN31 like we're doing on DCN35 and reorder
the reset writes to follow the HW programming guide.
Ensure we're reading SCRATCH7 instead of SCRATCH8 for the HALT code.
No current versions of DMCUB firmware use the SCRATCH8 boot bit to
dynamically switch where the HALT code goes to maintain backwards
compatibility with PSP.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 50f040c53e ("drm/amd/display: Increase halt
timeout for DMCUB to 1s")
There's two issues here:
1. Each poll is closer to 10us than 1us so it stalls for 15s on PNP.
2. We're reading the wrong scratch register to check for the HALT code.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
amdgpu_dm_find_first_crtc_matching_connector can return NULL.
It is necessary to the returned connector before passing it
drm_atomic_get_new_connector_state which always assumes connector is
not NULL.
Reviewed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why/How]
Certain PCON will clear the FRL_MODE bit despite supporting the link BW
indicated in the other bits.
Thus, skip checking the FRL_MODE bit when interpreting the
hdmi_encoded_link_bw struct.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: George Shen <george.shen@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
These are left required changes for dio encoder refactor.
[HOW]
1. original logic is separated by config option
2. new link encoder dp enable/disable code for dcn35
3. process fec only for DP 8b10b encoding
Reviewed-by: Cruise Hung <cruise.hung@amd.com>
Signed-off-by: Peichen Huang <PeiChen.Huang@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
It should no longer use DMCUB_SOFT_RESET as it can result
in the memory request path becoming desynchronized.
[HOW]
To ensure robustness in the reset sequence:
1) Extend timeout on the "halt" command sent via gpint, and check for
controller to enter "wait" as a stronger guarantee that there are no
requests to memory still in flight.
2) Remove usage of DMCUB_SOFT_RESET
3) Rely on PSP to reset the controller safely
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY&HOW]
P-state type would remain on previously used when unsupported which
causes confusion in logging and visual confirm, so set back to zero
when unsupported.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Dillon Varone <Dillon.Varone@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When SubVP is active the HW cursor size is limited to 64x64, and
anything larger will force composition which is bad for gaming on
DCN3.2 if the game uses a larger cursor.
[how]
If HW cursor is requested, typically by a fullscreen game, do not
enable SubVP so that up to 256x256 cursor sizes are available for
DCN3.2.
Reviewed-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Aric Cyr <Aric.Cyr@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a type mismatch between what CalculateDynamicMetadataParameters()
takes and what is passed to it. Currently this function accepts several
args as signed long but it's called with unsigned integers and integer. On
some systems where long is 32 bits and one of these unsigned int params is
greater than INT_MAX it may cause passing input params as negative values.
Fix this by changing these argument types from long to unsigned int and to
int respectively. Also this will align the function's definition with
similar functions in other dcn* drivers.
Found by Linux Verification Center (linuxtesting.org) with Svace.
Fixes: 6725a88f88 ("drm/amd/display: Add DCN3 DML")
Signed-off-by: Vitaliy Shevtsov <v.shevtsov@mt-integration.ru>
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Null pointer dereference issue could occur when pipe_ctx->plane_state
is null. The fix adds a check to ensure 'pipe_ctx->plane_state' is not
null before accessing. This prevents a null pointer dereference.
Found by code review.
Fixes: 3be5262e35 ("drm/amd/display: Rename more dc_surface stuff to plane_state")
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Ma Ke <make24@iscas.ac.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The last use of optc3_fpu_set_vrr_m_const() was removed in 2022's
commit 64f991590f ("drm/amd/display: Fix a compilation failure on PowerPC
caused by FPU code")
which removed the only caller (with a similar) name.
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
All dce command_table_helper's shares a copy-pasted collection
of copy-pasted functions, which are: phy_id_to_atom,
clock_source_id_to_atom_phy_clk_src_id, and engine_bp_to_atom.
This patch removes the multiple copy-pasted by moving them to
the command_table_helper.c and make the command_table_helper's
calls the functions implemented by the command_table_helper.c
instead.
The changes were not tested on actual hardware. I am only able
to verify that the changes keep the code compileable and do my
best to to look repeatedly if I am not actually changing any code.
This is the version 4 of the PATCH, fixed comments about
licence in the new files and the matches From email to
Signed-off-by email. Fixed comments about using
command_table_helper instead of creating a dce_common
Signed-off-by: Luan Icaro Pinto Arcanjo <luanicaro@usp.br>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
some board designs have eDP0 connected to DP1, need a way to enable
support_edp0_on_dp1 flag, otherwise edp related features cannot work
[how]
do a dmi check during dm initialization to identify systems that
require support_edp0_on_dp1. Optimize quirk table with callback
functions to set quirk entries, retrieve_dmi_info can set quirks
according to quirk entries
Cc: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Yilin Chen <Yilin.Chen@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit f6d17270d1)
Cc: stable@vger.kernel.org
