Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Wait for device readiness after reset by polling Vendor ID and
looking for Configuration RRS instead of polling the Command
register and looking for non-error completions, to avoid hardware
retries done for RRS on non-Vendor ID reads (Bjorn Helgaas)
- Rename CRS Completion Status to RRS ('Request Retry Status') to
match PCIe r6.0 spec usage (Bjorn Helgaas)
- Clear LBMS bit after a manual link retrain so we don't try to
retrain a link when there's no downstream device anymore (Maciej W.
Rozycki)
- Revert to the original link speed after retraining fails instead of
leaving it restricted to 2.5GT/s, so a future device has a chance
to use higher speeds (Maciej W. Rozycki)
- Wait for each level of downstream bus, not just the first, to
become accessible before restoring devices on that bus (Ilpo
Järvinen)
- Add ARCH_PCI_DEV_GROUPS so s390 can add its own attribute_groups
without having to stomp on the core's pdev->dev.groups (Lukas
Wunner)
Driver binding:
- Export pcim_request_region(), a managed counterpart of
pci_request_region(), for use by drivers (Philipp Stanner)
- Export pcim_iomap_region() and deprecate pcim_iomap_regions()
(Philipp Stanner)
- Request the PCI BAR used by xboxvideo (Philipp Stanner)
- Request and map drm/ast BARs with pcim_iomap_region() (Philipp
Stanner)
MSI:
- Add MSI_FLAG_NO_AFFINITY flag for devices that mux MSIs onto a
single IRQ line and cannot set the affinity of each MSI to a
specific CPU core (Marek Vasut)
- Use MSI_FLAG_NO_AFFINITY and remove unnecessary .irq_set_affinity()
implementations in aardvark, altera, brcmstb, dwc, mediatek-gen3,
mediatek, mobiveil, plda, rcar, tegra, vmd, xilinx-nwl,
xilinx-xdma, and xilinx drivers to avoid 'IRQ: set affinity failed'
warnings (Marek Vasut)
Power management:
- Add pwrctl support for ATH11K inside the WCN6855 package (Konrad
Dybcio)
PCI device hotplug:
- Remove unnecessary hpc_ops struct from shpchp (ngn)
- Check for PCI_POSSIBLE_ERROR(), not 0xffffffff, in cpqphp
(weiyufeng)
Virtualization:
- Mark Creative Labs EMU20k2 INTx masking as broken (Alex Williamson)
- Add an ACS quirk for Qualcomm SA8775P, which doesn't advertise ACS
but does provide ACS-like features (Subramanian Ananthanarayanan)
IOMMU:
- Add function 0 DMA alias quirk for Glenfly Arise audio function,
which uses the function 0 Requester ID (WangYuli)
NPEM:
- Add Native PCIe Enclosure Management (NPEM) support for sysfs
control of NVMe RAID storage indicators (ok/fail/locate/
rebuild/etc) (Mariusz Tkaczyk)
- Add support for the ACPI _DSM PCIe SSD status LED management, which
is functionally similar to NPEM but mediated by platform firmware
(Mariusz Tkaczyk)
Device trees:
- Drop minItems and maxItems from ranges in PCI generic host binding
since host bridges may have several MMIO and I/O port apertures
(Frank Li)
- Add kirin, rcar-gen2, uniphier DT binding top-level constraints for
clocks (Krzysztof Kozlowski)
Altera PCIe controller driver:
- Convert altera DT bindings from text to YAML (Matthew Gerlach)
- Replace TLP_REQ_ID() with macro PCI_DEVID(), which does the same
thing and is what other drivers use (Jinjie Ruan)
Broadcom STB PCIe controller driver:
- Add DT binding maxItems for reset controllers (Jim Quinlan)
- Use the 'bridge' reset method if described in the DT (Jim Quinlan)
- Use the 'swinit' reset method if described in the DT (Jim Quinlan)
- Add 'has_phy' so the existence of a 'rescal' reset controller
doesn't imply software control of it (Jim Quinlan)
- Add support for many inbound DMA windows (Jim Quinlan)
- Rename SoC 'type' to 'soc_base' express the fact that SoCs come in
families of multiple similar devices (Jim Quinlan)
- Add Broadcom 7712 DT description and driver support (Jim Quinlan)
- Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings for
maintainability (Bjorn Helgaas)
Freescale i.MX6 PCIe controller driver:
- Add imx6q-pcie 'dbi2' and 'atu' reg-names for i.MX8M Endpoints
(Richard Zhu)
- Fix a code restructuring error that caused i.MX8MM and i.MX8MP
Endpoints to fail to establish link (Richard Zhu)
- Fix i.MX8MP Endpoint occasional failure to trigger MSI by enforcing
outbound alignment requirement (Richard Zhu)
- Call phy_power_off() in the .probe() error path (Frank Li)
- Rename internal names from imx6_* to imx_* since i.MX7/8/9 are also
supported (Frank Li)
- Manage Refclk by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Manage core reset by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Expand comments for erratum ERR010728 workaround (Frank Li)
- Use generic PHY APIs to configure mode, speed, and submode, which
is harmless for devices that implement their own internal PHY
management and don't set the generic imx_pcie->phy (Frank Li)
- Add i.MX8Q (i.MX8QM, i.MX8QXP, and i.MX8DXL) DT binding and driver
Root Complex support (Richard Zhu)
Freescale Layerscape PCIe controller driver:
- Replace layerscape-pcie DT binding compatible fsl,lx2160a-pcie with
fsl,lx2160ar2-pcie (Frank Li)
- Add layerscape-pcie DT binding deprecated 'num-viewport' property
to address a DT checker warning (Frank Li)
- Change layerscape-pcie DT binding 'fsl,pcie-scfg' to phandle-array
(Frank Li)
Loongson PCIe controller driver:
- Increase max PCI hosts to 8 for Loongson-3C6000 and newer chipsets
(Huacai Chen)
Marvell Aardvark PCIe controller driver:
- Fix issue with emulating Configuration RRS for two-byte reads of
Vendor ID; previously it only worked for four-byte reads (Bjorn
Helgaas)
MediaTek PCIe Gen3 controller driver:
- Add per-SoC struct mtk_gen3_pcie_pdata to support multiple SoC
types (Lorenzo Bianconi)
- Use reset_bulk APIs to manage PHY reset lines (Lorenzo Bianconi)
- Add DT and driver support for Airoha EN7581 PCIe controller
(Lorenzo Bianconi)
Qualcomm PCIe controller driver:
- Update qcom,pcie-sc7280 DT binding with eight interrupts (Rayyan
Ansari)
- Add back DT 'vddpe-3v3-supply', which was incorrectly removed
earlier (Johan Hovold)
- Drop endpoint redundant masking of global IRQ events (Manivannan
Sadhasivam)
- Clarify unknown global IRQ message and only log it once to avoid a
flood (Manivannan Sadhasivam)
- Add 'linux,pci-domain' property to endpoint DT binding (Manivannan
Sadhasivam)
- Assign PCI domain number for endpoint controllers (Manivannan
Sadhasivam)
- Add 'qcom_pcie_ep' and the PCI domain number to IRQ names for
endpoint controller (Manivannan Sadhasivam)
- Add global SPI interrupt for PCIe link events to DT binding
(Manivannan Sadhasivam)
- Add global RC interrupt handler to handle 'Link up' events and
automatically enumerate hot-added devices (Manivannan Sadhasivam)
- Avoid mirroring of DBI and iATU register space so it doesn't
overlap BAR MMIO space (Prudhvi Yarlagadda)
- Enable controller resources like PHY only after PERST# is
deasserted to partially avoid the problem that the endpoint SoC
crashes when accessing things when Refclk is absent (Manivannan
Sadhasivam)
- Add 16.0 GT/s equalization and RX lane margining settings (Shashank
Babu Chinta Venkata)
- Pass domain number to pci_bus_release_domain_nr() explicitly to
avoid a NULL pointer dereference (Manivannan Sadhasivam)
Renesas R-Car PCIe controller driver:
- Make the read-only const array 'check_addr' static (Colin Ian King)
- Add R-Car V4M (R8A779H0) PCIe host and endpoint to DT binding
(Yoshihiro Shimoda)
TI DRA7xx PCIe controller driver:
- Request IRQF_ONESHOT for 'dra7xx-pcie-main' IRQ since the primary
handler is NULL (Siddharth Vadapalli)
- Handle IRQ request errors during root port and endpoint probe
(Siddharth Vadapalli)
TI J721E PCIe driver:
- Add DT 'ti,syscon-acspcie-proxy-ctrl' and driver support to enable
the ACSPCIE module to drive Refclk for the Endpoint (Siddharth
Vadapalli)
- Extract the cadence link setup from cdns_pcie_host_setup() so link
setup can be done separately during resume (Thomas Richard)
- Add T_PERST_CLK_US definition for the mandatory delay between
Refclk becoming stable and PERST# being deasserted (Thomas Richard)
- Add j721e suspend and resume support (Théo Lebrun)
TI Keystone PCIe controller driver:
- Fix NULL pointer checking when applying MRRS limitation quirk for
AM65x SR 1.0 Errata #i2037 (Dan Carpenter)
Xilinx NWL PCIe controller driver:
- Fix off-by-one error in INTx IRQ handler that caused INTx
interrupts to be lost or delivered as the wrong interrupt (Sean
Anderson)
- Rate-limit misc interrupt messages (Sean Anderson)
- Turn off the clock on probe failure and device removal (Sean
Anderson)
- Add DT binding and driver support for enabling/disabling PHYs (Sean
Anderson)
- Add PCIe phy bindings for the ZCU102 (Sean Anderson)
Xilinx XDMA PCIe controller driver:
- Add support for Xilinx QDMA Soft IP PCIe Root Port Bridge to DT
binding and xilinx-dma-pl driver (Thippeswamy Havalige)
Miscellaneous:
- Fix buffer overflow in kirin_pcie_parse_port() (Alexandra Diupina)
- Fix minor kerneldoc issues and typos (Bjorn Helgaas)
- Use PCI_DEVID() macro in aer_inject() instead of open-coding it
(Jinjie Ruan)
- Check pcie_find_root_port() return in x86 fixups to avoid NULL
pointer dereferences (Samasth Norway Ananda)
- Make pci_bus_type constant (Kunwu Chan)
- Remove unused declarations of __pci_pme_wakeup() and
pci_vpd_release() (Yue Haibing)
- Remove any leftover .*.cmd files with make clean (zhang jiao)
- Remove unused BILLION macro (zhang jiao)"
* tag 'pci-v6.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (132 commits)
PCI: Fix typos
dt-bindings: PCI: qcom: Allow 'vddpe-3v3-supply' again
tools: PCI: Remove unused BILLION macro
tools: PCI: Remove .*.cmd files with make clean
PCI: Pass domain number to pci_bus_release_domain_nr() explicitly
PCI: dra7xx: Fix error handling when IRQ request fails in probe
PCI: dra7xx: Fix threaded IRQ request for "dra7xx-pcie-main" IRQ
PCI: qcom: Add RX lane margining settings for 16.0 GT/s
PCI: qcom: Add equalization settings for 16.0 GT/s
PCI: dwc: Always cache the maximum link speed value in dw_pcie::max_link_speed
PCI: dwc: Rename 'dw_pcie::link_gen' to 'dw_pcie::max_link_speed'
PCI: qcom-ep: Enable controller resources like PHY only after refclk is available
PCI: Mark Creative Labs EMU20k2 INTx masking as broken
dt-bindings: PCI: imx6q-pcie: Add reg-name "dbi2" and "atu" for i.MX8M PCIe Endpoint
dt-bindings: PCI: altera: msi: Convert to YAML
PCI: imx6: Add i.MX8Q PCIe Root Complex (RC) support
PCI: Rename CRS Completion Status to RRS
PCI: aardvark: Correct Configuration RRS checking
PCI: Wait for device readiness with Configuration RRS
PCI: brcmstb: Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings
...
Inline ast_vga_connector_init() into its only caller. The helper
currently only does half of the connector-init work and is trivial
enough to be inlined. While at it, remove the error message from the
call to ast_ddc_create(). The function already warns on errors.
Also set the local variables for encoder and connector as late as
possible, so that the compiler warns if we use them before having
initialized the instance.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240911115347.899148-9-tzimmermann@suse.de
Inline ast_sil164_connector_init() into its only caller. The helper
currently only does half of the connector-init work and is trivial
enough to be inlined. While at it, remove the error message from the
call to ast_ddc_create(). The function already warns on errors.
Also set the local variables for encoder and connector as late as
possible, so that the compiler warns if we use them before having
initialized the instance.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240911115347.899148-8-tzimmermann@suse.de
Inline ast_dp501_connector_init() into its only caller. The helper
currently only does half of the connector-init work and is trivial
enough to be inlined.
Also set the local variables for encoder and connector as late as
possible, so that the compiler warns if we use them before having
initialized the instance.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240911115347.899148-6-tzimmermann@suse.de
Replace ast_dp_set_on_off() with ast_dp_set_enable(). The helper's
new name reflects the performed operation. If enabling fails, the
new helper prints a warning. The code that waits for the programmed
effect to take place is now located in __ast_dp_wait_enable().
Also align the register constants with the rest of the code.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240911115347.899148-5-tzimmermann@suse.de
Replace the helper for controlling power on the physical connector,
ast_dp_power_on_off(), with ast_dp_set_phy_sleep(). The new name
reflects the effect of the operation. Simplify the implementation.
The call now controls sleeping, hence semantics are inversed. Each
'on' becomes an 'off' operation and vice versa.
Do the same for ast_dp_power_is_on() and also align naming of the
register constant with the rest of the code.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240911115347.899148-4-tzimmermann@suse.de
Inline ast_astdp_connector_init() into its only caller. The helper
currently only does half of the connector-init work and is trivial
enough to be inlined.
Also set the local variables for encoder and connector as late as
possible, so that the compiler warns if we use them before having
initialized the instance.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240911115347.899148-2-tzimmermann@suse.de
Ast's BMC connector tracks the status of an underlying physical
connector and updates the BMC status accordingly. This functionality
works around GNOME's settings app, which cannot handle multiple
outputs on the same CRTC.
The workaround is now obsolete as all code for physical outputs
handle BMC support internally. Hence, remove the driver's code and
the BMC output entirely.
v3:
- remove struct ast_bmc_connector
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240815151953.184679-12-tzimmermann@suse.de
Permanently set the connector status to 'connected'. Return BMC modes
for connector if no display is attached to the physical DP connector.
Otherwise use EDID modes as before.
If the status of the physical connector changes, the driver still
generates a hotplug event. DRM clients will then reconfigure their
output to a mode appropriate for either physical display or BMC.
v3:
- use struct ast_connector.physical_status to handle BMC
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240815151953.184679-11-tzimmermann@suse.de
Permanently set the connector status to 'connected'. Return BMC modes
for connector if no display is attached to the physical DP connector.
Otherwise use EDID modes as before.
If the status of the physical connector changes, the driver still
generates a hotplug event. DRM clients will then reconfigure their
output to a mode appropriate for either physical display or BMC.
v3:
- use struct ast_connector.physical_status to handle BMC
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240815151953.184679-10-tzimmermann@suse.de
Permanently set the connector status to 'connected'. Return BMC modes
for connector if no display is attached to the physical DP connector.
Otherwise use EDID modes as before.
If the status of the physical connector changes, the driver still
generates a hotplug event. DRM clients will then reconfigure their
output to a mode appropriate for either physical display or BMC.
v3:
- use struct ast_connector.physical_status to handle BMC
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240815151953.184679-9-tzimmermann@suse.de
Permanently set the connector status to 'connected'. Return BMC modes
for connector if no display is attached to the physical DP connector.
Otherwise use EDID modes as before.
If the status of the physical connector changes, the driver still
generates a hotplug event. DRM clients will then reconfigure their
output to a mode appropriate for either physical display or BMC.
v3:
- use struct ast_connector.physical_status to handle BMC
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240815151953.184679-7-tzimmermann@suse.de
Convert ASTDP support to struct drm_edid and its helpers. Simplifies
and modernizes the EDID handling.
The driver reads 4 bytes at once, but the overall read length is now
variable. Therefore update the EDID read loop to never return more than
the requested bytes.
The device does not seem to support EDID extensions, as the driver
actively clears any such information from the main EDID header. As
the new interface allows for reading extension blocks for EDID, make
sure that the block is always 0 (i.e., the main header). A later
update might fix that.
v2:
- fix reading if len is not a multiple of 4
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240815151953.184679-5-tzimmermann@suse.de
The place for link training is in the encoder's atomic_enable
helper. Remove all related tests from other helper ASTDP functions;
especially ast_astdp_is_connected(), which tests HPD status.
DP link training is controlled by the firmware. A status flag reports
success or failure. The process can be fragile on Aspeed hardware. Moving
the test from connector detection to the atomic_enable allows for several
retries and a longer timeout.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240717143319.104012-5-tzimmermann@suse.de
The function ast_crtc_dpms() is left over from when the ast driver
did not implement atomic modesetting. But DPMS is not supported by
atomic modesetting and the helper is only called to enable or
disable the CRTC sync pulses. Inline the function into its callers.
To disable the CRTC, ast sets (AST_DPMS_VSYNC_OFF | AST_DPMS_HSYNC_OFF)
in VGACRB6. Replace the constants with the correct register constants
for VGACRB6.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240627153638.8765-8-tzimmermann@suse.de
The SCREEN_DISABLE bit controls scanout from display memory. The bit
affects all planes, so set it only in the CRTC's atomic enable and
disable functions.
A number of bugs affect this fix. First of all, ast_set_std_regs()
tries to set VGASR1 except for the SD bit. But the read bitmask is
invert, so it preserves anything except the SD bit. Fix this by
re-inverting the read mask.
The second issue is that primary-plane and CRTC helpers modify the
SD bit. The bit controls scanout for all planes, primary and HW
cursor, so set it only in the CRTC code.
Further add a constant to represent the SD bit in VGASR1. Keep the
plane's atomic_disable around to make the DRM framework happy.
v2:
- fix typos in commit message
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240627153638.8765-7-tzimmermann@suse.de
Several color registers are programmed in the DPMS code of the CRTC's
atomic_enable helper and the primary plane's atomic_update. It requires
the color format and the display mode.
Both code paths handle different cases: the DPMS's code will not be
executed if the color format changes without a full mode switch. The
plane's code only runs if the color format changes, but ignores
display-mode changes.
The color format is a property of the primary plane, so consolidate all
color-format code in the plane's atomic_update. Remove it from the DPMS
helper.
v2:
- clarify commit message (Jocelyn)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240627153638.8765-5-tzimmermann@suse.de
Do all mode setting in ast_crtc_helper_mode_set_nofb(), which
always runs after disabling the CRTC and before programming the
planes. Removes implicit synchronization between the CRTC's
atomic disable, enable and the vertical retrace.
Display-mode updates require HW cursors to be disabled. The HW
cursor only picks up changes at vertical retrace periods. So the
CRTC's atomic_disable helper waited for the retrace to delay any
following mode-setting operations, which then happened in
atomic_enable. See [1] for a description of the problem.
With the CRTC helper callback mode_set_nofb, we can now synchronize
and reprogram in the same place. As it always runs before the plane
update, the plane code can be reordered with the CRTC's later
atomic_enable et al.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/series/79914/ # 1
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240627153638.8765-4-tzimmermann@suse.de
