The drm_bridge structure contains an encoder pointer that is widely used
by bridge drivers. This pattern is largely documented as deprecated in
other KMS entities for atomic drivers.
However, one of the main use of that pointer is done in attach to just
call drm_bridge_attach on the next bridge to add it to the bridge list.
While this dereferences the bridge->encoder pointer, it's effectively
the same encoder the bridge was being attached to.
We can make it more explicit by adding the encoder the bridge is
attached to to the list of attach parameters. This also removes the need
to dereference bridge->encoder in most drivers.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250313-bridge-connector-v6-1-511c54a604fb@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
HDCP KSV list readback can choose to use AUX FIFO or
general data register.
For some DisplayPort devices, the KSV list must be read
in 5 byte boundaries.
The original AUX read command does not support these devices.
The AUX command operation control register "REG_AUX_CMD_REQ" uses b[3:0]
as AUX operacion control, and b[7:4] are status bits and read only.
To change KSV read operation uses "CMD_AUX_NATIVE_READ" from using
the data registers to using AUX FIFO.
The extended command "CMD_AUX_GET_KSV_LIST" is added as
"CMD_AUX_NATIVE_READ" with the 0x10 flag which selects AUX FIFO mode.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Hermes Wu <hermes.wu@ite.com.tw>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241230-v7-upstream-v7-3-e0fdd4844703@ite.corp-partner.google.com
The IT6505 bridge chip has a active low reset line. Since it is a
"reset" and not an "enable" line, the GPIO should be asserted to
put it in reset and deasserted to bring it out of reset during
the power on sequence.
The polarity was inverted when the driver was first introduced, likely
because the device family that was targeted had an inverting level
shifter on the reset line.
The MT8186 Corsola devices already have the IT6505 in their device tree,
but the whole display pipeline is actually disabled and won't be enabled
until some remaining issues are sorted out. The other known user is
the MT8183 Kukui / Jacuzzi family; their device trees currently do not
have the IT6505 included.
Fix the polarity in the driver while there are no actual users.
Fixes: b5c84a9edc ("drm/bridge: add it6505 driver")
Cc: stable@vger.kernel.org
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20241029095411.657616-1-wenst@chromium.org
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
The bridge might miss the display change events when it's powered off.
This happens when a user changes the external monitor when the system
is suspended and the embedded controller doesn't not wake AP up.
It's also observed that one DP-to-HDMI bridge doesn't work correctly
when there is no EDID read after it is powered on.
Drop the cache to force an EDID read after system resume to fix this.
Fixes: 11feaef69d ("drm/bridge: it6505: Add caching for EDID")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240926092931.3870342-3-treapking@chromium.org
When the system power resumes, the TTL input of IT6505 may experience
some noise before the video signal stabilizes, necessitating a video
reset. This patch is implemented to prevent a loop of video error
interrupts, which can occur when a video reset in the video FIFO error
interrupt triggers another such interrupt. The patch processes the SCDT
and FIFO error interrupts simultaneously and ignores any video FIFO
error interrupts caused by a video reset.
Fixes: b5c84a9edc ("drm/bridge: add it6505 driver")
Signed-off-by: Kuro Chung <kuro.chung@ite.com.tw>
Signed-off-by: Hermes Wu <hermes.wu@ite.com.tw>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240522065528.1053439-1-kuro.chung@ite.com.tw
In it6505_bridge_attach(), the check on the existence of 'bridge->encoder'
is not necessary, as it has already been checked in the drm_bridge_attach()
which happens prior to it6505_bridge_attach() get called. Note that the
it6505_bridge_attach() will only be called by .attach() of the previous
bridge or KMS driver. The previous drm_bridge_attach() will quit with a
negative error code returned if it fails for some reasons. Hence, it is
guaranteed that the .encoder member of the drm_bridge instance is not NULL
when it6505_bridge_attach() function get called.
Remove the redundant checking codes "if (!bridge->encoder) { ... }".
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sui Jingfeng <sui.jingfeng@linux.dev>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240513153109.46786-6-sui.jingfeng@linux.dev
On system resume, the driver might call it6505_poweron directly if the
runtime PM hasn't been enabled. In such case, pm_runtime_get_if_in_use
will always return 0 because dev->power.runtime_status stays at
RPM_SUSPENDED, and the IRQ will never be handled.
Use it6505->powered from the driver struct fixes this because it always
gets updated when it6505_poweron is called.
Fixes: 5eb9a43140 ("drm/bridge: it6505: Guard bridge power in IRQ handler")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230727100131.2338127-1-treapking@chromium.org
The address of a data structure member was determined before
a corresponding null pointer check in the implementation of
the function “receive_timing_debugfs_show”.
Thus avoid the risk for undefined behaviour by moving the assignment
for the variable “vid” behind the null pointer check.
This issue was detected by using the Coccinelle software.
Fixes: b5c84a9edc ("drm/bridge: add it6505 driver")
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Link: https://patchwork.freedesktop.org/patch/msgid/fa69384f-1485-142b-c4ee-3df54ac68a89@web.de
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Originally, the it6505 relies on a short sleep in the IRQ handler and a
long sleep to make sure it6505->lane_swap and it6505->lane_count is
configured in it6505_extcon_work and it6505_detect, respectively.
Use completion and additional DPCD read to remove the unnecessary waits,
and use a different lock for it6505_extcon_work and the threaded IRQ
handler because they no longer need to run exclusively.
The wait time of the completion is usually less than 10ms in local
experiments, but leave it larger here just in case.
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221013110411.1674359-4-treapking@chromium.org
Pull drm updates from Dave Airlie:
"Lots of stuff all over, some new AMD IP support and gang submit
support. i915 has further DG2 and Meteorlake pieces, and a bunch of
i915 display refactoring. msm has a shrinker rework. There are also a
bunch of conversions to use kunit.
This has two external pieces, some MEI changes needed for future Intel
discrete GPUs. These should be acked by Greg. There is also a cross
maintainer shared tree with some backlight rework from Hans in here.
Core:
- convert selftests to kunit
- managed init for more objects
- move to idr_init_base
- rename fb and gem cma helpers to dma
- hide unregistered connectors from getconnector ioctl
- DSC passthrough aux support
- backlight handling improvements
- add dma_resv_assert_held to vmap/vunmap
edid:
- move luminance calculation to core
fbdev:
- fix aperture helper usage
fourcc:
- add more format helpers
- add DRM_FORMAT_Cxx, DRM_FORMAT_Rxx, DRM_FORMAT_Dxx
- add packed AYUV8888, XYUV8888
- add some kunit tests
ttm:
- allow bos without backing store
- rewrite placement to use intersect/compatible functions
dma-buf:
- docs update
- improve signalling when debugging
udmabuf:
- fix failure path GPF
dp:
- drop dp/mst legacy code
- atomic mst state support
- audio infoframe packing
panel:
- Samsung LTL101AL01
- B120XAN01.0
- R140NWF5 RH
- DMT028VGHMCMI-1A T
- AUO B133UAN02.1
- IVO M133NW4J-R3
- Innolux N120ACA-EA1
amdgpu:
- Gang submit support
- Mode2 reset for RDNA2
- New IP support:
DCN 3.1.4, 3.2
SMU 13.x
NBIO 7.7
GC 11.x
PSP 13.x
SDMA 6.x
GMC 11.x
- DSC passthrough support
- PSP fixes for TA support
- vangogh GFXOFF stats
- clang fixes
- gang submit CS cleanup prep work
- fix VRAM eviction issues
amdkfd:
- GC 10.3 IP ISA fixes
- fix CRIU regression
- CPU fault on COW mapping fixes
i915:
- align fw versioning with kernel practices
- add display substruct to i915 private
- add initial runtime info to driver info
- split out HDCP and backlight registers
- MEI XeHP SDV GSC support
- add per-gt sysfs defaults
- TLB invalidation improvements
- Disable PCI BAR resize on 32-bit
- GuC firmware updates and compat changes
- GuC log timestamp translation
- DG2 preemption workaround changes
- DG2 improved HDMI pixel clocks support
- PCI BAR sanity checks
- Enable DC5 on DG2
- DG2 DMC fw bumped
- ADL-S PCI ID added
- Meteorlake enablement
- Rename ggtt_view to gtt_view
- host RPS fixes
- release mmaps on rpm suspend on discrete
- clocking and dpll refactoring
- VBT definitions and parsing updates
- SKL watermark code extracted to separate file
- allow seamless M/N changes on eDP panels
- BUG_ON removal and cleanups
msm:
- DPU:
simplified VBIF configuration
cleanup CTL interfaces
- DSI:
removed unused msm_display_dsc_config struct
switch regulator calls to new API
switched to PANEL_BRIDGE for direct attached panels
- DSI_PHY: convert drivers to parent_hws
- DP: cleanup pixel_rate handling
- HDMI: turned hdmi-phy-8996 into OF clk provider
- misc dt-bindings fixes
- choose eDP as primary display if it's available
- support getting interconnects from either the mdss or the mdp5/dpu
device nodes
- gem: Shrinker + LRU re-work:
- adds a shared GEM LRU+shrinker helper and moves msm over to that
- reduce lock contention between retire and submit by avoiding the
need to acquire obj lock in retire path (and instead using resv
seeing obj's busyness in the shrinker
- fix reclaim vs submit issues
- GEM fault injection for triggering userspace error paths
- Map/unmap optimization
- Improved robustness for a6xx GPU recovery
virtio:
- improve error and edge conditions handling
- convert to use managed helpers
- stop exposing LINEAR modifier
mgag200:
- split modeset handling per model
udl:
- suspend/disconnect handling improvements
vc4:
- rework HDMI power up
- depend on PM
- better unplugging support
ast:
- resolution handling improvements
ingenic:
- add JZ4760(B) support
- avoid a modeset when sharpness property is unchanged
- use the new PM ops
it6505:
- power seq and clock updates
ssd130x:
- regmap bulk write
- use atomic helpers instead of simple helpers
via:
- rename via_drv to via_dri1, consolidate all code.
radeon:
- drop DP MST experimental support
- delayed work flush fix
- use time_after
ti-sn65dsi86:
- DP support
mediatek:
- MT8195 DP support
- drop of_gpio header
- remove unneeded result
- small DP code improvements
vkms:
- RGB565, XRGB64 and ARGB64 support
sun4i:
- tv: convert to atomic
rcar-du:
- Synopsys DW HDMI bridge DT bindings update
exynos:
- use drm_display_info.is_hdmi
- correct return of mixer_mode_valid and hdmi_mode_valid
omap:
- refcounting fix
rockchip:
- RK3568 support
- RK3399 gamma support"
* tag 'drm-next-2022-10-05' of git://anongit.freedesktop.org/drm/drm: (1374 commits)
drm/amdkfd: Fix UBSAN shift-out-of-bounds warning
drm/amdkfd: Track unified memory when switching xnack mode
drm/amdgpu: Enable sram on vcn_4_0_2
drm/amdgpu: Enable VCN DPG for GC11_0_1
drm/msm: Fix build break with recent mm tree
drm/panel: simple: Use dev_err_probe() to simplify code
drm/panel: panel-edp: Use dev_err_probe() to simplify code
drm/panel: simple: Add Multi-Inno Technology MI0800FT-9
dt-bindings: display: simple: Add Multi-Inno Technology MI0800FT-9 panel
drm/amdgpu: correct the memcpy size for ip discovery firmware
drm/amdgpu: Skip put_reset_domain if it doesn't exist
drm/amdgpu: remove switch from amdgpu_gmc_noretry_set
drm/amdgpu: Fix mc_umc_status used uninitialized warning
drm/amd/display: Prevent OTG shutdown during PSR SU
drm/amdgpu: add page retirement handling for CPU RAS
drm/amdgpu: use RAS error address convert api in mca notifier
drm/amdgpu: support to convert dedicated umc mca address
drm/amdgpu: export umc error address convert interface
drm/amdgpu: fix sdma v4 init microcode error
drm/amd/display: fix array-bounds error in dc_stream_remove_writeback()
...
