Link Training Tunable PHY Repeaters (LTTPRs) are defined in DisplayPort
1.4a specification. As the name suggests, these PHY repeaters are
capable of adjusting their output for link training purposes.
According to the DisplayPort standard, LTTPRs have two operating
modes:
- non-transparent - it replies to DPCD LTTPR field specific AUX
requests, while passes through all other AUX requests
- transparent - it passes through all AUX requests.
Switching between these two modes is done by the DPTX by issuing
an AUX write to the DPCD PHY_REPEATER_MODE register.
The msm DP driver is currently lacking any handling of LTTPRs.
This means that if at least one LTTPR is found between DPTX and DPRX,
the link training would fail if that LTTPR was not already configured
in transparent mode.
The section 3.6.6.1 from the DisplayPort v2.0 specification mandates
that before link training with the LTTPR is started, the DPTX may place
the LTTPR in non-transparent mode by first switching to transparent mode
and then to non-transparent mode. This operation seems to be needed only
on first link training and doesn't need to be done again until device is
unplugged.
It has been observed on a few X Elite-based platforms which have
such LTTPRs in their board design that the DPTX needs to follow the
procedure described above in order for the link training to be successful.
So add support for reading the LTTPR DPCD caps to figure out the number
of such LTTPRs first. Then, for platforms (or Type-C dongles) that have
at least one such an LTTPR, set its operation mode to transparent mode
first and then to non-transparent, just like the mentioned section of
the specification mandates.
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250203-drm-dp-msm-add-lttpr-transparent-mode-set-v5-4-c865d0e56d6e@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes for v6.14-rc4
Display:
* More catalog fixes:
- to skip watchdog programming through top block if its not present
- fix the setting of WB mask to ensure the WB input control is programmed
correctly through ping-pong
- drop lm_pair for sm6150 as that chipset does not have any 3dmerge block
* Fix the mode validation logic for DP/eDP to account for widebus (2ppc)
to allow high clock resolutions
* Fix to disable dither during encoder disable as otherwise this was
causing kms_writeback failure due to resource sharing between
* WB and DSI paths as DSI uses dither but WB does not
* Fixes for virtual planes, namely to drop extraneous return and fix
uninitialized variables
* Fix to avoid spill-over of DSC encoder block bits when programming
the bits-per-component
* Fixes in the DSI PHY to protect against concurrent access of
PHY_CMN_CLK_CFG regs between clock and display drivers
Core/GPU:
* Fix non-blocking fence wait incorrectly rounding up to 1 jiffy timeout
* Only print GMU fw version once, instead of each time the GPU resumes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGtt2AODBXdod8ULXcAygf_qYvwRDVeUVtODx=2jErp6cA@mail.gmail.com
Widebus allows the DP controller to operate in 2 pixel per clock mode.
The mode validation logic validates the mode->clock against the max
DP pixel clock. However the max DP pixel clock limit assumes widebus
is already enabled. Adjust the mode validation logic to only compare
the adjusted pixel clock which accounts for widebus against the max DP
pixel clock. Also fix the mode validation logic for YUV420 modes as in
that case as well, only half the pixel clock is needed.
Cc: stable@vger.kernel.org
Fixes: 757a2f36ab ("drm/msm/dp: enable widebus feature for display port")
Fixes: 6db6e56065 ("drm/msm/dp: change clock related programming for YUV420 over DP")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dale Whinham <daleyo@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/635789/
Link: https://lore.kernel.org/r/20250206-dp-widebus-fix-v2-1-cb89a0313286@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Updates for v6.14
MDSS:
- properly described UBWC registers
- added SM6150 (aka QCS615) support
MDP4:
- several small fixes
DPU:
- added SM6150 (aka QCS615) support
- enabled wide planes if virtual planes are enabled (by using two SSPPs for a single plane)
- fixed modes filtering for platforms w/o 3DMux
- fixed DSPP DSPP_2 / _3 links on several platforms
- corrected DSPP definitions on SDM670
- added CWB hardware blocks support
- added VBIF to DPU snapshots
- dropped struct dpu_rm_requirements
DP:
- reworked DP audio support
DSI:
- added SM6150 (aka QCS615) support
GPU:
- Print GMU core fw version
- GMU bandwidth voting for a740 and a750
- Expose uche trap base via uapi
- UAPI error reporting
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGsutUu4ff6OpXNXxqf1xaV0rV6oV23VXNRiF0_OEfe72Q@mail.gmail.com
The continual trickle of small conversion patches is grating on me, and
is really not helping. Just get rid of the 'remove_new' member
function, which is just an alias for the plain 'remove', and had a
comment to that effect:
/*
* .remove_new() is a relic from a prototype conversion of .remove().
* New drivers are supposed to implement .remove(). Once all drivers are
* converted to not use .remove_new any more, it will be dropped.
*/
This was just a tree-wide 'sed' script that replaced '.remove_new' with
'.remove', with some care taken to turn a subsequent tab into two tabs
to make things line up.
I did do some minimal manual whitespace adjustment for places that used
spaces to line things up.
Then I just removed the old (sic) .remove_new member function, and this
is the end result. No more unnecessary conversion noise.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As documented in the description of the transfer() function of
"struct drm_dp_aux", the transfer() function can be called at any time
regardless of the state of the DP port. Specifically if the kernel has
the DP AUX character device enabled and userspace accesses
"/dev/drm_dp_auxN" directly then the AUX transfer function will be
called regardless of whether a DP device is connected.
For eDP panels we have a special rule where we wait (with a 5 second
timeout) for HPD to go high. This rule was important before all panels
drivers were converted to call wait_hpd_asserted() and actually can be
removed in a future commit.
For external DP devices we never checked for HPD. That means that
trying to access the DP AUX character device (AKA `hexdump -C
/dev/drm_dp_auxN`) would very, very slowly timeout. Specifically on my
system:
$ time hexdump -C /dev/drm_dp_aux0
hexdump: /dev/drm_dp_aux0: Connection timed out
real 0m8.200s
We want access to the drm_dp_auxN character device to fail faster than
8 seconds when no DP cable is plugged in.
Let's add a test to make transfers fail right away if a device isn't
plugged in. Rather than testing the HPD line directly, we have the
dp_display module tell us when AUX transfers should be enabled so we
can handle cases where HPD is signaled out of band like with Type C.
Fixes: c943b4948b ("drm/msm/dp: add displayPort driver support")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/583127/
Link: https://lore.kernel.org/r/20240315143621.v2.1.I16aff881c9fe82b5e0fc06ca312da017aa7b5b3e@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Merge DisplayPort subnode API in order to allow DisplayPort driver to
configure the PHYs either to the DP or eDP mode, depending on hardware
configuration.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Pull drm updates from Dave Airlie:
"Highlights are usual, more AMD IP blocks for future hw, i915/xe
changes, Displayport tunnelling support for i915, msm YUV over DP
changes, new tests for ttm, but its mostly a lot of stuff all over the
place from lots of people.
core:
- EDID cleanups
- scheduler error handling fixes
- managed: add drmm_release_action() with tests
- add ratelimited drm debug print
- DPCD PSR early transport macro
- DP tunneling and bandwidth allocation helpers
- remove built-in edids
- dp: Avoid AUX transfers on powered-down displays
- dp: Add VSC SDP helpers
cross drivers:
- use new drm print helpers
- switch to ->read_edid callback
- gem: add stats for shared buffers plus updates to amdgpu, i915, xe
syncobj:
- fixes to waiting and sleeping
ttm:
- add tests
- fix errno codes
- simply busy-placement handling
- fix page decryption
media:
- tc358743: fix v4l device registration
video:
- move all kernel parameters for video behind CONFIG_VIDEO
sound:
- remove <drm/drm_edid.h> include from header
ci:
- add tests for msm
- fix apq8016 runner
efifb:
- use copy of global screen_info state
vesafb:
- use copy of global screen_info state
simplefb:
- fix logging
bridge:
- ite-6505: fix DP link-training bug
- samsung-dsim: fix error checking in probe
- samsung-dsim: add bsh-smm-s2/pro boards
- tc358767: fix regmap usage
- imx: add i.MX8MP HDMI PVI plus DT bindings
- imx: add i.MX8MP HDMI TX plus DT bindings
- sii902x: fix probing and unregistration
- tc358767: limit pixel PLL input range
- switch to new drm_bridge_read_edid() interface
panel:
- ltk050h3146w: error-handling fixes
- panel-edp: support delay between power-on and enable; use put_sync
in unprepare; support Mediatek MT8173 Chromebooks, BOE NV116WHM-N49
V8.0, BOE NV122WUM-N41, CSO MNC207QS1-1 plus DT bindings
- panel-lvds: support EDT ETML0700Z9NDHA plus DT bindings
- panel-novatek: FRIDA FRD400B25025-A-CTK plus DT bindings
- add BOE TH101MB31IG002-28A plus DT bindings
- add EDT ETML1010G3DRA plus DT bindings
- add Novatek NT36672E LCD DSI plus DT bindings
- nt36523: support 120Hz timings, fix includes
- simple: fix display timings on RK32FN48H
- visionox-vtdr6130: fix initialization
- add Powkiddy RGB10MAX3 plus DT bindings
- st7703: support panel rotation plus DT bindings
- add Himax HX83112A plus DT bindings
- ltk500hd1829: add support for ltk101b4029w and admatec 9904370
- simple: add BOE BP082WX1-100 8.2" panel plus DT bindungs
panel-orientation-quirks:
- GPD Win Mini
amdgpu:
- Validate DMABuf imports in compute VMs
- Add RAS ACA framework
- PSP 13 fixes
- Misc code cleanups
- Replay fixes
- Atom interpretor PS, WS bounds checking
- DML2 fixes
- Audio fixes
- DCN 3.5 Z state fixes
- Remove deprecated ida_simple usage
- UBSAN fixes
- RAS fixes
- Enable seq64 infrastructure
- DC color block enablement
- Documentation updates
- DC documentation updates
- DMCUB updates
- ATHUB 4.1 support
- LSDMA 7.0 support
- JPEG DPG support
- IH 7.0 support
- HDP 7.0 support
- VCN 5.0 support
- SMU 13.0.6 updates
- NBIO 7.11 updates
- SDMA 6.1 updates
- MMHUB 3.3 updates
- DCN 3.5.1 support
- NBIF 6.3.1 support
- VPE 6.1.1 support
amdkfd:
- Validate DMABuf imports in compute VMs
- SVM fixes
- Trap handler updates and enhancements
- Fix cache size reporting
- Relocate the trap handler
radeon:
- Atom interpretor PS, WS bounds checking
- Misc code cleanups
xe:
- new query for GuC submission version
- Remove unused persistent exec_queues
- Add vram frequency sysfs attributes
- Add the flag XE_VM_BIND_FLAG_DUMPABLE
- Drop pre-production workarounds
- Drop kunit tests for unsupported platforms
- Start pumbling SR-IOV support with memory based interrupts for VF
- Allow to map BO in GGTT with PAT index corresponding to XE_CACHE_UC
to work with memory based interrupts
- Add GuC Doorbells Manager as prep work SR-IOV
- Implement additional workarounds for xe2 and MTL
- Program a few registers according to perfomance guide spec for Xe2
- Fix remaining 32b build issues and enable it back
- Fix build with CONFIG_DEBUG_FS=n
- Fix warnings from GuC ABI headers
- Introduce Relay Communication for SR-IOV for VF <-> GuC <-> PF
- Release mmap mappings on rpm suspend
- Disable mid-thread preemption when not properly supported by
hardware
- Fix xe_exec by reserving extra fence slot for CPU bind
- Fix xe_exec with full long running exec queue
- Canonicalize addresses where needed for Xe2 and add to devcoredum
- Toggle USM support for Xe2
- Only allow 1 ufence per exec / bind IOCTL
- Add GuC firmware loading for Lunar Lake
- Add XE_VMA_PTE_64K VMA flag
i915:
- Add more ADL-N PCI IDs
- Enable fastboot also on older platforms
- Early transport for panel replay and PSR
- New ARL PCI IDs
- DP TPS4 PHY test pattern support
- Unify and improve VSC SDP for PSR and non-PSR cases
- Refactor memory regions and improve debug logging
- Rework global state serialization
- Remove unused CDCLK divider fields
- Unify HDCP connector logging format
- Use display instead of graphics version in display code
- Move VBT and opregion debugfs next to the implementation
- Abstract opregion interface, use opaque type
- MTL fixes
- HPD handling fixes
- Add GuC submission interface version query
- Atomically invalidate userptr on mmu-notifier
- Update handling of MMIO triggered reports
- Don't make assumptions about intel_wakeref_t type
- Extend driver code of Xe_LPG to Xe_LPG+
- Add flex arrays to struct i915_syncmap
- Allow for very slow HuC loading
- DP tunneling and bandwidth allocation support
msm:
- Correct bindings for MSM8976 and SM8650 platforms
- Start migration of MDP5 platforms to DPU driver
- X1E80100 MDSS support
- DPU:
- Improve DSC allocation, fixing several important corner cases
- Add support for SDM630/SDM660 platforms
- Simplify dpu_encoder_phys_ops
- Apply fixes targeting DSC support with a single DSC encoder
- Apply fixes for HCTL_EN timing configuration
- X1E80100 support
- Add support for YUV420 over DP
- GPU:
- fix sc7180 UBWC config
- fix a7xx LLC config
- new gpu support: a305B, a750, a702
- machine support: SM7150 (different power levels than other a618)
- a7xx devcoredump support
habanalabs:
- configure IRQ affinity according to NUMA node
- move HBM MMU page tables inside the HBM
- improve device reset
- check extended PCIe errors
ivpu:
- updates to firmware API
- refactor BO allocation
imx:
- use devm_ functions during init
hisilicon:
- fix EDID includes
mgag200:
- improve ioremap usage
- convert to struct drm_edid
- Work around PCI write bursts
nouveau:
- disp: use kmemdup()
- fix EDID includes
- documentation fixes
qaic:
- fixes to BO handling
- make use of DRM managed release
- fix order of remove operations
rockchip:
- analogix_dp: get encoder port from DT
- inno_hdmi: support HDMI for RK3128
- lvds: error-handling fixes
ssd130x:
- support SSD133x plus DT bindings
tegra:
- fix error handling
tilcdc:
- make use of DRM managed release
v3d:
- show memory stats in debugfs
- Support display MMU page size
vc4:
- fix error handling in plane prepare_fb
- fix framebuffer test in plane helpers
virtio:
- add venus capset defines
vkms:
- fix OOB access when programming the LUT
- Kconfig improvements
vmwgfx:
- unmap surface before changing plane state
- fix memory leak in error handling
- documentation fixes
- list command SVGA_3D_CMD_DEFINE_GB_SURFACE_V4 as invalid
- fix null-pointer deref in execbuf
- refactor display-mode probing
- fix fencing for creating cursor MOBs
- fix cursor-memory lifetime
xlnx:
- fix live video input for ZynqMP DPSUB
lima:
- fix memory leak
loongson:
- fail if no VRAM present
meson:
- switch to new drm_bridge_read_edid() interface
renesas:
- add RZ/G2L DU support plus DT bindings
mxsfb:
- Use managed mode config
sun4i:
- HDMI: updates to atomic mode setting
mediatek:
- Add display driver for MT8188 VDOSYS1
- DSI driver cleanups
- Filter modes according to hardware capability
- Fix a null pointer crash in mtk_drm_crtc_finish_page_flip
etnaviv:
- enhancements for NPU and MRT support"
* tag 'drm-next-2024-03-13' of https://gitlab.freedesktop.org/drm/kernel: (1420 commits)
drm/amd/display: Removed redundant @ symbol to fix kernel-doc warnings in -next repo
drm/amd/pm: wait for completion of the EnableGfxImu message
drm/amdgpu/soc21: add mode2 asic reset for SMU IP v14.0.1
drm/amdgpu: add smu 14.0.1 support
drm/amdgpu: add VPE 6.1.1 discovery support
drm/amdgpu/vpe: add VPE 6.1.1 support
drm/amdgpu/vpe: don't emit cond exec command under collaborate mode
drm/amdgpu/vpe: add collaborate mode support for VPE
drm/amdgpu/vpe: add PRED_EXE and COLLAB_SYNC OPCODE
drm/amdgpu/vpe: add multi instance VPE support
drm/amdgpu/discovery: add nbif v6_3_1 ip block
drm/amdgpu: Add nbif v6_3_1 ip block support
drm/amdgpu: Add pcie v6_1_0 ip headers (v5)
drm/amdgpu: Add nbif v6_3_1 ip headers (v5)
arch/powerpc: Remove <linux/fb.h> from backlight code
macintosh/via-pmu-backlight: Include <linux/backlight.h>
fbdev/chipsfb: Include <linux/backlight.h>
drm/etnaviv: Restore some id values
drm/amdkfd: make kfd_class constant
drm/amdgpu: add ring timeout information in devcoredump
...
All the components of YUV420 over DP are added. Therefore, let's mark the
connector property as true for DP connector when the DP type is not eDP
and when there is a CDM block available.
Changes in v3:
- Move setting the connector's ycbcr_420_allowed parameter so
that it is not dependent on if the dp_display is not eDP
Changes in v2:
- Check for if dp_catalog has a CDM block available instead of
checking if VSC SDP is allowed when setting the dp connector's
ycbcr_420_allowed parameter
Signed-off-by: Paloma Arellano <quic_parellan@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/579628/
Link: https://lore.kernel.org/r/20240222194025.25329-20-quic_parellan@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Adjust the encoder format programming in the case of video mode for DP
to accommodate CDM related changes.
Changes in v4:
- Remove hw_cdm check in dpu_encoder_needs_periph_flush()
- Remove hw_cdm check when getting the fmt_fourcc in
dpu_encoder_phys_vid_enable()
Changes in v2:
- Move timing engine programming to a separate patch from this
one
- Move update_pending_flush_periph() invocation completely to
this patch
- Change the logic of dpu_encoder_get_drm_fmt() so that it only
calls drm_mode_is_420_only() instead of doing additional
unnecessary checks
- Create new functions msm_dp_needs_periph_flush() and it's
supporting function dpu_encoder_needs_periph_flush() to check
if the mode is YUV420 and VSC SDP is enabled before doing a
peripheral flush
Signed-off-by: Paloma Arellano <quic_parellan@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/579641/
Link: https://lore.kernel.org/r/20240222194025.25329-17-quic_parellan@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
