The HSYNC/VSYNC polarity of rk3036 HDMI are controlled by GRF.
Without the polarity configuration in GRF, it can be observed
from the HDMI protocol analyzer that the H/V front/back timing
output by RK3036 HDMI are currently not in line with the specifications.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Heiko Stuebner <heiko@sntech.de> #rk3036-kylin
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250422070455.432666-5-andyshrk@163.com
DRM_DISPLAY_DP_AUX_BUS cannot be selected when CONFIG_OF is disabled:
WARNING: unmet direct dependencies detected for DRM_DISPLAY_DP_AUX_BUS
Depends on [n]: HAS_IOMEM [=y] && DRM [=y] && OF [=n]
Selected by [y]:
- DRM_ROCKCHIP [=y] && HAS_IOMEM [=y] && DRM [=y] && ROCKCHIP_IOMMU [=y] && ROCKCHIP_ANALOGIX_DP [=y]
Rockchip platforms all depend on OF anyway, so add the dependency here
for compile testing.
Fixes: d7b4936b2b ("drm/rockchip: analogix_dp: Add support to get panel from the DP AUX bus")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Acked-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250423164422.2793634-1-arnd@kernel.org
RK3588 integrates the Analogix eDP 1.3 TX controller IP and the HDMI/eDP
TX Combo PHY based on a Samsung IP block. There are also two independent
eDP display interface with different address on RK3588 Soc.
The patch currently adds only the basic support, specifically RGB output
up to 4K@60Hz, without the tests for audio, PSR and other eDP 1.3 specific
features.
In additon, the above Analogix IP has always been utilized as eDP on
Rockchip platform, despite its capability to also support the DP v1.2.
Therefore, the newly added logs will contain the term 'edp' rather than
'dp'. And the newly added 'apb' reset control is to ensure the APB bus
of eDP controller works well on the RK3588 SoC.
Acked-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Link: https://lore.kernel.org/r/20250310104114.2608063-12-damon.ding@rock-chips.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Move drm_of_find_panel_or_bridge() a little later and combine it with
component_add() into a new function rockchip_dp_link_panel(). The function
will serve as done_probing() callback of devm_of_dp_aux_populate_bus(),
aiding to support for obtaining the eDP panel via the DP AUX bus.
If failed to get the panel from the DP AUX bus, it will then try the other
way to get panel information through the platform bus.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20250310104114.2608063-9-damon.ding@rock-chips.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Because the layer/window enable/disable is take effect by vsync, if the
overlay configuration of these layers does not follow vsync and
takes effect immediately instead, when multiple layers are dynamically
enable/disable, inconsistent display contents may be seen on the screen.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250318062024.4555-1-andyshrk@163.com
Commit 52d11c863a ("drm/rockchip: lvds: do not print scary message when
probing defer") already started hiding scary messages that are not relevant
if the requested supply just returned EPROBE_DEFER, but there are more
possible sources - like the phy.
So modernize the whole logging in the probe path by replacing the
remaining deprecated DRM_DEV_ERROR with appropriate dev_err(_probe)
and drm_err calls.
The distinction here is that all messages talking about mishaps of the
lvds element use dev_err(_probe) while messages caused by interaction
with the main Rockchip drm-device use drm_err.
Reviewed-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250304124418.111061-3-heiko@sntech.de
The LVDS block needs a separate pclk only on some socs, so currently
requests and prepares it in the soc-specific probe function, but common
code is required to unprepare it in the error path or on driver remove.
While this works because clk_unprepare just does nothing if clk is NULL,
this mismatch of who is responsible still is not very nice.
The clock-framework already has a helper for clk-get-and-prepare even
with devres support in devm_clk_get_prepared().
This will get and prepare the clock and also unprepare it on driver
removal, saving the driver from having to handle it "manually".
Reviewed-by: Quentin Schulz <quentin.schulz@cherry.de>
Reviewed-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@cherry.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250304124418.111061-2-heiko@sntech.de
When the drm-driver probes, it mainly creates the component device, where
all the sub-drivers (vops, hdmi, etc) hook into.
This will cause the shutdown handler to get called on shutdown, even
though the drm-device might not have been set up, or the component bind
might have failed.
So use the new component helper to check whether the drm-device is up
and only then call the drm-atomic helper to release all the drm magic.
This prevents failures when the drm-device is never set, or has been
freed up already for example by a probe-defer during the component bind.
Reviewed-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Tested-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250220234141.2788785-3-heiko@sntech.de
Replace drm_err() calls in vop2_bind() and vop2_create_crtcs() with
dev_err_probe(), to simplify error handling and improve consistency.
Additionally, ensure the already existing dev_err_probe() invocations
pass drm->dev instead of dev as their first argument, so that we get the
actual reason in case of -EPROBE_DEFER errors:
platform display-subsystem: deferred probe pending: (reason unknown)
vs.
platform display-subsystem: deferred probe pending: rockchip-drm: <actual reason>
While at it, add the missing '\n' to some of the message strings.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250223-vop2-hdmi1-disp-modes-v2-2-f4cec5e06fbe@collabora.com
The RK3588 specific implementation is currently quite limited in terms
of handling the full range of display modes supported by the connected
screens, e.g. 2560x1440@75Hz, 2048x1152@60Hz, 1024x768@60Hz are just a
few of them.
Additionally, it doesn't cope well with non-integer refresh rates like
59.94, 29.97, 23.98, etc.
Make use of HDMI1 PHY PLL as a more accurate DCLK source to handle
all display modes up to 4K@60Hz.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250223-vop2-hdmi1-disp-modes-v2-1-f4cec5e06fbe@collabora.com
Currently, DRM atomic uAPI allows only primary planes to be flipped
asynchronously. However, each driver might be able to perform async
flips in other different plane types. To enable drivers to set their own
restrictions on which type of plane they can or cannot flip, use the
existing atomic_async_check() from struct drm_plane_helper_funcs to
enhance this flexibility, thus allowing different plane types to be able
to do async flips as well.
Create a new parameter for the atomic_async_check(), `bool flip`. This
parameter is used to distinguish when this function is being called from
a plane update from a full page flip.
In order to prevent regressions and such, we keep the current policy: we
skip the driver check for the primary plane, because it is always
allowed to do async flips on it.
Signed-off-by: André Almeida <andrealmeid@igalia.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Christopher Snowhill <chris@kode54.net>
Tested-by: Christopher Snowhill <chris@kode54.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20250127-tonyk-async_flip-v12-1-0f7f8a8610d3@igalia.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
The RK3588 specific implementation is currently quite limited in terms
of handling the full range of display modes supported by the connected
screens, e.g. 2560x1440@75Hz, 2048x1152@60Hz, 1024x768@60Hz are just a
few of them.
Additionally, it doesn't cope well with non-integer refresh rates like
59.94, 29.97, 23.98, etc.
Make use of HDMI0 PHY PLL as a more accurate DCLK source to handle
all display modes up to 4K@60Hz.
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20250204-vop2-hdmi0-disp-modes-v3-3-d71c6a196e58@collabora.com
The code that changes hdmi->ref_clk was accidentally copied from
downstream code that sets a different clock. We don't actually
want to set any clock here at all.
Setting this clock incorrectly leads to incorrect timings for
DDC, CEC, and HDCP signal generation.
No Fixes listed, as the theoretical timing error in DDC appears to
still be within tolerances and harmless - and HDCP and CEC are not
yet supported.
Signed-off-by: Derek Foreman <derek.foreman@collabora.com>
Reviewed-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20241217201708.3320673-1-derek.foreman@collabora.com
Every layer of vop2 should bind a window, and we also need to make
sure that this window is not used by other layer.
0x5 is a reserved layer sel value on rk3568, but it will select
Cluster3 on rk3588, configure unused layers to 0x5 will lead
alpha blending error on rk3588.
When we bind a window from layerM to layerN, we move the old window
on layerN to layerM.
Fixes: 604be85547 ("drm/rockchip: Add VOP2 driver")
Tested-by: Derek Foreman <derek.foreman@collabora.com>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20241214081719.3330518-3-andyshrk@163.com
