Currently, the LBR code assumes that LBR Freeze is supported on all processors
when X86_FEATURE_AMD_LBR_V2 is available i.e. CPUID leaf 0x80000022[EAX]
bit 1 is set. This is incorrect as the availability of the feature is
additionally dependent on CPUID leaf 0x80000022[EAX] bit 2 being set,
which may not be set for all Zen 4 processors.
Define a new feature bit for LBR and PMC freeze and set the freeze enable bit
(FLBRI) in DebugCtl (MSR 0x1d9) conditionally.
It should still be possible to use LBR without freeze for profile-guided
optimization of user programs by using an user-only branch filter during
profiling. When the user-only filter is enabled, branches are no longer
recorded after the transition to CPL 0 upon PMI arrival. When branch
entries are read in the PMI handler, the branch stack does not change.
E.g.
$ perf record -j any,u -e ex_ret_brn_tkn ./workload
Since the feature bit is visible under flags in /proc/cpuinfo, it can be
used to determine the feasibility of use-cases which require LBR Freeze
to be supported by the hardware such as profile-guided optimization of
kernels.
Fixes: ca5b7c0d96 ("perf/x86/amd/lbr: Add LbrExtV2 branch record support")
Signed-off-by: Sandipan Das <sandipan.das@amd.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/69a453c97cfd11c6f2584b19f937fe6df741510f.1711091584.git.sandipan.das@amd.com
Pull x86 fixes from Thomas Gleixner:
- Ensure that the encryption mask at boot is properly propagated on
5-level page tables, otherwise the PGD entry is incorrectly set to
non-encrypted, which causes system crashes during boot.
- Undo the deferred 5-level page table setup as it cannot work with
memory encryption enabled.
- Prevent inconsistent XFD state on CPU hotplug, where the MSR is reset
to the default value but the cached variable is not, so subsequent
comparisons might yield the wrong result and as a consequence the
result prevents updating the MSR.
- Register the local APIC address only once in the MPPARSE enumeration
to prevent triggering the related WARN_ONs() in the APIC and topology
code.
- Handle the case where no APIC is found gracefully by registering a
fake APIC in the topology code. That makes all related topology
functions work correctly and does not affect the actual APIC driver
code at all.
- Don't evaluate logical IDs during early boot as the local APIC IDs
are not yet enumerated and the invoked function returns an error
code. Nothing requires the logical IDs before the final CPUID
enumeration takes place, which happens after the enumeration.
- Cure the fallout of the per CPU rework on UP which misplaced the
copying of boot_cpu_data to per CPU data so that the final update to
boot_cpu_data got lost which caused inconsistent state and boot
crashes.
- Use copy_from_kernel_nofault() in the kprobes setup as there is no
guarantee that the address can be safely accessed.
- Reorder struct members in struct saved_context to work around another
kmemleak false positive
- Remove the buggy code which tries to update the E820 kexec table for
setup_data as that is never passed to the kexec kernel.
- Update the resource control documentation to use the proper units.
- Fix a Kconfig warning observed with tinyconfig
* tag 'x86-urgent-2024-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot/64: Move 5-level paging global variable assignments back
x86/boot/64: Apply encryption mask to 5-level pagetable update
x86/cpu: Add model number for another Intel Arrow Lake mobile processor
x86/fpu: Keep xfd_state in sync with MSR_IA32_XFD
Documentation/x86: Document that resctrl bandwidth control units are MiB
x86/mpparse: Register APIC address only once
x86/topology: Handle the !APIC case gracefully
x86/topology: Don't evaluate logical IDs during early boot
x86/cpu: Ensure that CPU info updates are propagated on UP
kprobes/x86: Use copy_from_kernel_nofault() to read from unsafe address
x86/pm: Work around false positive kmemleak report in msr_build_context()
x86/kexec: Do not update E820 kexec table for setup_data
x86/config: Fix warning for 'make ARCH=x86_64 tinyconfig'
If there is no local APIC enumerated and registered then the topology
bitmaps are empty. Therefore, topology_init_possible_cpus() will die with
a division by zero exception.
Prevent this by registering a fake APIC id to populate the topology
bitmap. This also allows to use all topology query interfaces
unconditionally. It does not affect the actual APIC code because either
the local APIC address was not registered or no local APIC could be
detected.
Fixes: f1f758a805 ("x86/topology: Add a mechanism to track topology via APIC IDs")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240322185305.242709302@linutronix.de
The local APICs have not yet been enumerated so the logical ID evaluation
from the topology bitmaps does not work and would return an error code.
Skip the evaluation during the early boot CPUID evaluation and only apply
it on the final run.
Fixes: 380414be78 ("x86/cpu/topology: Use topology logical mapping mechanism")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240322185305.186943142@linutronix.de
The boot sequence evaluates CPUID information twice:
1) During early boot
2) When finalizing the early setup right before
mitigations are selected and alternatives are patched.
In both cases the evaluation is stored in boot_cpu_data, but on UP the
copying of boot_cpu_data to the per CPU info of the boot CPU happens
between #1 and #2. So any update which happens in #2 is never propagated to
the per CPU info instance.
Consolidate the whole logic and copy boot_cpu_data right before applying
alternatives as that's the point where boot_cpu_data is in it's final
state and not supposed to change anymore.
This also removes the voodoo mb() from smp_prepare_cpus_common() which
had absolutely no purpose.
Fixes: 71eb4893cf ("x86/percpu: Cure per CPU madness on UP")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20240322185305.127642785@linutronix.de
Pull hyperv updates from Wei Liu:
- Use Hyper-V entropy to seed guest random number generator (Michael
Kelley)
- Convert to platform remove callback returning void for vmbus (Uwe
Kleine-König)
- Introduce hv_get_hypervisor_version function (Nuno Das Neves)
- Rename some HV_REGISTER_* defines for consistency (Nuno Das Neves)
- Change prefix of generic HV_REGISTER_* MSRs to HV_MSR_* (Nuno Das
Neves)
- Cosmetic changes for hv_spinlock.c (Purna Pavan Chandra Aekkaladevi)
- Use per cpu initial stack for vtl context (Saurabh Sengar)
* tag 'hyperv-next-signed-20240320' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
x86/hyperv: Use Hyper-V entropy to seed guest random number generator
x86/hyperv: Cosmetic changes for hv_spinlock.c
hyperv-tlfs: Rename some HV_REGISTER_* defines for consistency
hv: vmbus: Convert to platform remove callback returning void
mshyperv: Introduce hv_get_hypervisor_version function
x86/hyperv: Use per cpu initial stack for vtl context
hyperv-tlfs: Change prefix of generic HV_REGISTER_* MSRs to HV_MSR_*
A Hyper-V host provides its guest VMs with entropy in a custom ACPI
table named "OEM0". The entropy bits are updated each time Hyper-V
boots the VM, and are suitable for seeding the Linux guest random
number generator (rng). See a brief description of OEM0 in [1].
Generation 2 VMs on Hyper-V use UEFI to boot. Existing EFI code in
Linux seeds the rng with entropy bits from the EFI_RNG_PROTOCOL.
Via this path, the rng is seeded very early during boot with good
entropy. The ACPI OEM0 table provided in such VMs is an additional
source of entropy.
Generation 1 VMs on Hyper-V boot from BIOS. For these VMs, Linux
doesn't currently get any entropy from the Hyper-V host. While this
is not fundamentally broken because Linux can generate its own entropy,
using the Hyper-V host provided entropy would get the rng off to a
better start and would do so earlier in the boot process.
Improve the rng seeding for Generation 1 VMs by having Hyper-V specific
code in Linux take advantage of the OEM0 table to seed the rng. For
Generation 2 VMs, use the OEM0 table to provide additional entropy
beyond the EFI_RNG_PROTOCOL. Because the OEM0 table is custom to
Hyper-V, parse it directly in the Hyper-V code in the Linux kernel
and use add_bootloader_randomness() to add it to the rng. Once the
entropy bits are read from OEM0, zero them out in the table so
they don't appear in /sys/firmware/acpi/tables/OEM0 in the running
VM. The zero'ing is done out of an abundance of caution to avoid
potential security risks to the rng. Also set the OEM0 data length
to zero so a kexec or other subsequent use of the table won't try
to use the zero'ed bits.
[1] https://download.microsoft.com/download/1/c/9/1c9813b8-089c-4fef-b2ad-ad80e79403ba/Whitepaper%20-%20The%20Windows%2010%20random%20number%20generation%20infrastructure.pdf
Signed-off-by: Michael Kelley <mhklinux@outlook.com>
Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com>
Link: https://lore.kernel.org/r/20240318155408.216851-1-mhklinux@outlook.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20240318155408.216851-1-mhklinux@outlook.com>
Pull kvm updates from Paolo Bonzini:
"S390:
- Changes to FPU handling came in via the main s390 pull request
- Only deliver to the guest the SCLP events that userspace has
requested
- More virtual vs physical address fixes (only a cleanup since
virtual and physical address spaces are currently the same)
- Fix selftests undefined behavior
x86:
- Fix a restriction that the guest can't program a PMU event whose
encoding matches an architectural event that isn't included in the
guest CPUID. The enumeration of an architectural event only says
that if a CPU supports an architectural event, then the event can
be programmed *using the architectural encoding*. The enumeration
does NOT say anything about the encoding when the CPU doesn't
report support the event *in general*. It might support it, and it
might support it using the same encoding that made it into the
architectural PMU spec
- Fix a variety of bugs in KVM's emulation of RDPMC (more details on
individual commits) and add a selftest to verify KVM correctly
emulates RDMPC, counter availability, and a variety of other
PMC-related behaviors that depend on guest CPUID and therefore are
easier to validate with selftests than with custom guests (aka
kvm-unit-tests)
- Zero out PMU state on AMD if the virtual PMU is disabled, it does
not cause any bug but it wastes time in various cases where KVM
would check if a PMC event needs to be synthesized
- Optimize triggering of emulated events, with a nice ~10%
performance improvement in VM-Exit microbenchmarks when a vPMU is
exposed to the guest
- Tighten the check for "PMI in guest" to reduce false positives if
an NMI arrives in the host while KVM is handling an IRQ VM-Exit
- Fix a bug where KVM would report stale/bogus exit qualification
information when exiting to userspace with an internal error exit
code
- Add a VMX flag in /proc/cpuinfo to report 5-level EPT support
- Rework TDP MMU root unload, free, and alloc to run with mmu_lock
held for read, e.g. to avoid serializing vCPUs when userspace
deletes a memslot
- Tear down TDP MMU page tables at 4KiB granularity (used to be
1GiB). KVM doesn't support yielding in the middle of processing a
zap, and 1GiB granularity resulted in multi-millisecond lags that
are quite impolite for CONFIG_PREEMPT kernels
- Allocate write-tracking metadata on-demand to avoid the memory
overhead when a kernel is built with i915 virtualization support
but the workloads use neither shadow paging nor i915 virtualization
- Explicitly initialize a variety of on-stack variables in the
emulator that triggered KMSAN false positives
- Fix the debugregs ABI for 32-bit KVM
- Rework the "force immediate exit" code so that vendor code
ultimately decides how and when to force the exit, which allowed
some optimization for both Intel and AMD
- Fix a long-standing bug where kvm_has_noapic_vcpu could be left
elevated if vCPU creation ultimately failed, causing extra
unnecessary work
- Cleanup the logic for checking if the currently loaded vCPU is
in-kernel
- Harden against underflowing the active mmu_notifier invalidation
count, so that "bad" invalidations (usually due to bugs elsehwere
in the kernel) are detected earlier and are less likely to hang the
kernel
x86 Xen emulation:
- Overlay pages can now be cached based on host virtual address,
instead of guest physical addresses. This removes the need to
reconfigure and invalidate the cache if the guest changes the gpa
but the underlying host virtual address remains the same
- When possible, use a single host TSC value when computing the
deadline for Xen timers in order to improve the accuracy of the
timer emulation
- Inject pending upcall events when the vCPU software-enables its
APIC to fix a bug where an upcall can be lost (and to follow Xen's
behavior)
- Fall back to the slow path instead of warning if "fast" IRQ
delivery of Xen events fails, e.g. if the guest has aliased xAPIC
IDs
RISC-V:
- Support exception and interrupt handling in selftests
- New self test for RISC-V architectural timer (Sstc extension)
- New extension support (Ztso, Zacas)
- Support userspace emulation of random number seed CSRs
ARM:
- Infrastructure for building KVM's trap configuration based on the
architectural features (or lack thereof) advertised in the VM's ID
registers
- Support for mapping vfio-pci BARs as Normal-NC (vaguely similar to
x86's WC) at stage-2, improving the performance of interacting with
assigned devices that can tolerate it
- Conversion of KVM's representation of LPIs to an xarray, utilized
to address serialization some of the serialization on the LPI
injection path
- Support for _architectural_ VHE-only systems, advertised through
the absence of FEAT_E2H0 in the CPU's ID register
- Miscellaneous cleanups, fixes, and spelling corrections to KVM and
selftests
LoongArch:
- Set reserved bits as zero in CPUCFG
- Start SW timer only when vcpu is blocking
- Do not restart SW timer when it is expired
- Remove unnecessary CSR register saving during enter guest
- Misc cleanups and fixes as usual
Generic:
- Clean up Kconfig by removing CONFIG_HAVE_KVM, which was basically
always true on all architectures except MIPS (where Kconfig
determines the available depending on CPU capabilities). It is
replaced either by an architecture-dependent symbol for MIPS, and
IS_ENABLED(CONFIG_KVM) everywhere else
- Factor common "select" statements in common code instead of
requiring each architecture to specify it
- Remove thoroughly obsolete APIs from the uapi headers
- Move architecture-dependent stuff to uapi/asm/kvm.h
- Always flush the async page fault workqueue when a work item is
being removed, especially during vCPU destruction, to ensure that
there are no workers running in KVM code when all references to
KVM-the-module are gone, i.e. to prevent a very unlikely
use-after-free if kvm.ko is unloaded
- Grab a reference to the VM's mm_struct in the async #PF worker
itself instead of gifting the worker a reference, so that there's
no need to remember to *conditionally* clean up after the worker
Selftests:
- Reduce boilerplate especially when utilize selftest TAP
infrastructure
- Add basic smoke tests for SEV and SEV-ES, along with a pile of
library support for handling private/encrypted/protected memory
- Fix benign bugs where tests neglect to close() guest_memfd files"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (246 commits)
selftests: kvm: remove meaningless assignments in Makefiles
KVM: riscv: selftests: Add Zacas extension to get-reg-list test
RISC-V: KVM: Allow Zacas extension for Guest/VM
KVM: riscv: selftests: Add Ztso extension to get-reg-list test
RISC-V: KVM: Allow Ztso extension for Guest/VM
RISC-V: KVM: Forward SEED CSR access to user space
KVM: riscv: selftests: Add sstc timer test
KVM: riscv: selftests: Change vcpu_has_ext to a common function
KVM: riscv: selftests: Add guest helper to get vcpu id
KVM: riscv: selftests: Add exception handling support
LoongArch: KVM: Remove unnecessary CSR register saving during enter guest
LoongArch: KVM: Do not restart SW timer when it is expired
LoongArch: KVM: Start SW timer only when vcpu is blocking
LoongArch: KVM: Set reserved bits as zero in CPUCFG
KVM: selftests: Explicitly close guest_memfd files in some gmem tests
KVM: x86/xen: fix recursive deadlock in timer injection
KVM: pfncache: simplify locking and make more self-contained
KVM: x86/xen: remove WARN_ON_ONCE() with false positives in evtchn delivery
KVM: x86/xen: inject vCPU upcall vector when local APIC is enabled
KVM: x86/xen: improve accuracy of Xen timers
...
Pull MM updates from Andrew Morton:
- Sumanth Korikkar has taught s390 to allocate hotplug-time page frames
from hotplugged memory rather than only from main memory. Series
"implement "memmap on memory" feature on s390".
- More folio conversions from Matthew Wilcox in the series
"Convert memcontrol charge moving to use folios"
"mm: convert mm counter to take a folio"
- Chengming Zhou has optimized zswap's rbtree locking, providing
significant reductions in system time and modest but measurable
reductions in overall runtimes. The series is "mm/zswap: optimize the
scalability of zswap rb-tree".
- Chengming Zhou has also provided the series "mm/zswap: optimize zswap
lru list" which provides measurable runtime benefits in some
swap-intensive situations.
- And Chengming Zhou further optimizes zswap in the series "mm/zswap:
optimize for dynamic zswap_pools". Measured improvements are modest.
- zswap cleanups and simplifications from Yosry Ahmed in the series
"mm: zswap: simplify zswap_swapoff()".
- In the series "Add DAX ABI for memmap_on_memory", Vishal Verma has
contributed several DAX cleanups as well as adding a sysfs tunable to
control the memmap_on_memory setting when the dax device is
hotplugged as system memory.
- Johannes Weiner has added the large series "mm: zswap: cleanups",
which does that.
- More DAMON work from SeongJae Park in the series
"mm/damon: make DAMON debugfs interface deprecation unignorable"
"selftests/damon: add more tests for core functionalities and corner cases"
"Docs/mm/damon: misc readability improvements"
"mm/damon: let DAMOS feeds and tame/auto-tune itself"
- In the series "mm/mempolicy: weighted interleave mempolicy and sysfs
extension" Rakie Kim has developed a new mempolicy interleaving
policy wherein we allocate memory across nodes in a weighted fashion
rather than uniformly. This is beneficial in heterogeneous memory
environments appearing with CXL.
- Christophe Leroy has contributed some cleanup and consolidation work
against the ARM pagetable dumping code in the series "mm: ptdump:
Refactor CONFIG_DEBUG_WX and check_wx_pages debugfs attribute".
- Luis Chamberlain has added some additional xarray selftesting in the
series "test_xarray: advanced API multi-index tests".
- Muhammad Usama Anjum has reworked the selftest code to make its
human-readable output conform to the TAP ("Test Anything Protocol")
format. Amongst other things, this opens up the use of third-party
tools to parse and process out selftesting results.
- Ryan Roberts has added fork()-time PTE batching of THP ptes in the
series "mm/memory: optimize fork() with PTE-mapped THP". Mainly
targeted at arm64, this significantly speeds up fork() when the
process has a large number of pte-mapped folios.
- David Hildenbrand also gets in on the THP pte batching game in his
series "mm/memory: optimize unmap/zap with PTE-mapped THP". It
implements batching during munmap() and other pte teardown
situations. The microbenchmark improvements are nice.
- And in the series "Transparent Contiguous PTEs for User Mappings"
Ryan Roberts further utilizes arm's pte's contiguous bit ("contpte
mappings"). Kernel build times on arm64 improved nicely. Ryan's
series "Address some contpte nits" provides some followup work.
- In the series "mm/hugetlb: Restore the reservation" Breno Leitao has
fixed an obscure hugetlb race which was causing unnecessary page
faults. He has also added a reproducer under the selftest code.
- In the series "selftests/mm: Output cleanups for the compaction
test", Mark Brown did what the title claims.
- Kinsey Ho has added the series "mm/mglru: code cleanup and
refactoring".
- Even more zswap material from Nhat Pham. The series "fix and extend
zswap kselftests" does as claimed.
- In the series "Introduce cpu_dcache_is_aliasing() to fix DAX
regression" Mathieu Desnoyers has cleaned up and fixed rather a mess
in our handling of DAX on archiecctures which have virtually aliasing
data caches. The arm architecture is the main beneficiary.
- Lokesh Gidra's series "per-vma locks in userfaultfd" provides
dramatic improvements in worst-case mmap_lock hold times during
certain userfaultfd operations.
- Some page_owner enhancements and maintenance work from Oscar Salvador
in his series
"page_owner: print stacks and their outstanding allocations"
"page_owner: Fixup and cleanup"
- Uladzislau Rezki has contributed some vmalloc scalability
improvements in his series "Mitigate a vmap lock contention". It
realizes a 12x improvement for a certain microbenchmark.
- Some kexec/crash cleanup work from Baoquan He in the series "Split
crash out from kexec and clean up related config items".
- Some zsmalloc maintenance work from Chengming Zhou in the series
"mm/zsmalloc: fix and optimize objects/page migration"
"mm/zsmalloc: some cleanup for get/set_zspage_mapping()"
- Zi Yan has taught the MM to perform compaction on folios larger than
order=0. This a step along the path to implementaton of the merging
of large anonymous folios. The series is named "Enable >0 order folio
memory compaction".
- Christoph Hellwig has done quite a lot of cleanup work in the
pagecache writeback code in his series "convert write_cache_pages()
to an iterator".
- Some modest hugetlb cleanups and speedups in Vishal Moola's series
"Handle hugetlb faults under the VMA lock".
- Zi Yan has changed the page splitting code so we can split huge pages
into sizes other than order-0 to better utilize large folios. The
series is named "Split a folio to any lower order folios".
- David Hildenbrand has contributed the series "mm: remove
total_mapcount()", a cleanup.
- Matthew Wilcox has sought to improve the performance of bulk memory
freeing in his series "Rearrange batched folio freeing".
- Gang Li's series "hugetlb: parallelize hugetlb page init on boot"
provides large improvements in bootup times on large machines which
are configured to use large numbers of hugetlb pages.
- Matthew Wilcox's series "PageFlags cleanups" does that.
- Qi Zheng's series "minor fixes and supplement for ptdesc" does that
also. S390 is affected.
- Cleanups to our pagemap utility functions from Peter Xu in his series
"mm/treewide: Replace pXd_large() with pXd_leaf()".
- Nico Pache has fixed a few things with our hugepage selftests in his
series "selftests/mm: Improve Hugepage Test Handling in MM
Selftests".
- Also, of course, many singleton patches to many things. Please see
the individual changelogs for details.
* tag 'mm-stable-2024-03-13-20-04' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (435 commits)
mm/zswap: remove the memcpy if acomp is not sleepable
crypto: introduce: acomp_is_async to expose if comp drivers might sleep
memtest: use {READ,WRITE}_ONCE in memory scanning
mm: prohibit the last subpage from reusing the entire large folio
mm: recover pud_leaf() definitions in nopmd case
selftests/mm: skip the hugetlb-madvise tests on unmet hugepage requirements
selftests/mm: skip uffd hugetlb tests with insufficient hugepages
selftests/mm: dont fail testsuite due to a lack of hugepages
mm/huge_memory: skip invalid debugfs new_order input for folio split
mm/huge_memory: check new folio order when split a folio
mm, vmscan: retry kswapd's priority loop with cache_trim_mode off on failure
mm: add an explicit smp_wmb() to UFFDIO_CONTINUE
mm: fix list corruption in put_pages_list
mm: remove folio from deferred split list before uncharging it
filemap: avoid unnecessary major faults in filemap_fault()
mm,page_owner: drop unnecessary check
mm,page_owner: check for null stack_record before bumping its refcount
mm: swap: fix race between free_swap_and_cache() and swapoff()
mm/treewide: align up pXd_leaf() retval across archs
mm/treewide: drop pXd_large()
...
Pull x86 RFDS mitigation from Dave Hansen:
"RFDS is a CPU vulnerability that may allow a malicious userspace to
infer stale register values from kernel space. Kernel registers can
have all kinds of secrets in them so the mitigation is basically to
wait until the kernel is about to return to userspace and has user
values in the registers. At that point there is little chance of
kernel secrets ending up in the registers and the microarchitectural
state can be cleared.
This leverages some recent robustness fixes for the existing MDS
vulnerability. Both MDS and RFDS use the VERW instruction for
mitigation"
* tag 'rfds-for-linus-2024-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
KVM/x86: Export RFDS_NO and RFDS_CLEAR to guests
x86/rfds: Mitigate Register File Data Sampling (RFDS)
Documentation/hw-vuln: Add documentation for RFDS
x86/mmio: Disable KVM mitigation when X86_FEATURE_CLEAR_CPU_BUF is set
Pull core x86 updates from Ingo Molnar:
- The biggest change is the rework of the percpu code, to support the
'Named Address Spaces' GCC feature, by Uros Bizjak:
- This allows C code to access GS and FS segment relative memory
via variables declared with such attributes, which allows the
compiler to better optimize those accesses than the previous
inline assembly code.
- The series also includes a number of micro-optimizations for
various percpu access methods, plus a number of cleanups of %gs
accesses in assembly code.
- These changes have been exposed to linux-next testing for the
last ~5 months, with no known regressions in this area.
- Fix/clean up __switch_to()'s broken but accidentally working handling
of FPU switching - which also generates better code
- Propagate more RIP-relative addressing in assembly code, to generate
slightly better code
- Rework the CPU mitigations Kconfig space to be less idiosyncratic, to
make it easier for distros to follow & maintain these options
- Rework the x86 idle code to cure RCU violations and to clean up the
logic
- Clean up the vDSO Makefile logic
- Misc cleanups and fixes
* tag 'x86-core-2024-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (52 commits)
x86/idle: Select idle routine only once
x86/idle: Let prefer_mwait_c1_over_halt() return bool
x86/idle: Cleanup idle_setup()
x86/idle: Clean up idle selection
x86/idle: Sanitize X86_BUG_AMD_E400 handling
sched/idle: Conditionally handle tick broadcast in default_idle_call()
x86: Increase brk randomness entropy for 64-bit systems
x86/vdso: Move vDSO to mmap region
x86/vdso/kbuild: Group non-standard build attributes and primary object file rules together
x86/vdso: Fix rethunk patching for vdso-image-{32,64}.o
x86/retpoline: Ensure default return thunk isn't used at runtime
x86/vdso: Use CONFIG_COMPAT_32 to specify vdso32
x86/vdso: Use $(addprefix ) instead of $(foreach )
x86/vdso: Simplify obj-y addition
x86/vdso: Consolidate targets and clean-files
x86/bugs: Rename CONFIG_RETHUNK => CONFIG_MITIGATION_RETHUNK
x86/bugs: Rename CONFIG_CPU_SRSO => CONFIG_MITIGATION_SRSO
x86/bugs: Rename CONFIG_CPU_IBRS_ENTRY => CONFIG_MITIGATION_IBRS_ENTRY
x86/bugs: Rename CONFIG_CPU_UNRET_ENTRY => CONFIG_MITIGATION_UNRET_ENTRY
x86/bugs: Rename CONFIG_SLS => CONFIG_MITIGATION_SLS
...
Pull x86 cleanups from Ingo Molnar:
"Misc cleanups, including a large series from Thomas Gleixner to cure
sparse warnings"
* tag 'x86-cleanups-2024-03-11' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/nmi: Drop unused declaration of proc_nmi_enabled()
x86/callthunks: Use EXPORT_PER_CPU_SYMBOL_GPL() for per CPU variables
x86/cpu: Provide a declaration for itlb_multihit_kvm_mitigation
x86/cpu: Use EXPORT_PER_CPU_SYMBOL_GPL() for x86_spec_ctrl_current
x86/uaccess: Add missing __force to casts in __access_ok() and valid_user_address()
x86/percpu: Cure per CPU madness on UP
smp: Consolidate smp_prepare_boot_cpu()
x86/msr: Add missing __percpu annotations
x86/msr: Prepare for including <linux/percpu.h> into <asm/msr.h>
perf/x86/amd/uncore: Fix __percpu annotation
x86/nmi: Remove an unnecessary IS_ENABLED(CONFIG_SMP)
x86/apm_32: Remove dead function apm_get_battery_status()
x86/insn-eval: Fix function param name in get_eff_addr_sib()
Pull x86 SEV updates from Borislav Petkov:
- Add the x86 part of the SEV-SNP host support.
This will allow the kernel to be used as a KVM hypervisor capable of
running SNP (Secure Nested Paging) guests. Roughly speaking, SEV-SNP
is the ultimate goal of the AMD confidential computing side,
providing the most comprehensive confidential computing environment
up to date.
This is the x86 part and there is a KVM part which did not get ready
in time for the merge window so latter will be forthcoming in the
next cycle.
- Rework the early code's position-dependent SEV variable references in
order to allow building the kernel with clang and -fPIE/-fPIC and
-mcmodel=kernel
- The usual set of fixes, cleanups and improvements all over the place
* tag 'x86_sev_for_v6.9_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
x86/sev: Disable KMSAN for memory encryption TUs
x86/sev: Dump SEV_STATUS
crypto: ccp - Have it depend on AMD_IOMMU
iommu/amd: Fix failure return from snp_lookup_rmpentry()
x86/sev: Fix position dependent variable references in startup code
crypto: ccp: Make snp_range_list static
x86/Kconfig: Remove CONFIG_AMD_MEM_ENCRYPT_ACTIVE_BY_DEFAULT
Documentation: virt: Fix up pre-formatted text block for SEV ioctls
crypto: ccp: Add the SNP_SET_CONFIG command
crypto: ccp: Add the SNP_COMMIT command
crypto: ccp: Add the SNP_PLATFORM_STATUS command
x86/cpufeatures: Enable/unmask SEV-SNP CPU feature
KVM: SEV: Make AVIC backing, VMSA and VMCB memory allocation SNP safe
crypto: ccp: Add panic notifier for SEV/SNP firmware shutdown on kdump
iommu/amd: Clean up RMP entries for IOMMU pages during SNP shutdown
crypto: ccp: Handle legacy SEV commands when SNP is enabled
crypto: ccp: Handle non-volatile INIT_EX data when SNP is enabled
crypto: ccp: Handle the legacy TMR allocation when SNP is enabled
x86/sev: Introduce an SNP leaked pages list
crypto: ccp: Provide an API to issue SEV and SNP commands
...
Pull resource control updates from Borislav Petkov:
- Rework different aspects of the resctrl code like adding
arch-specific accessors and splitting the locking, in order to
accomodate ARM's MPAM implementation of hw resource control and be
able to use the same filesystem control interface like on x86. Work
by James Morse
- Improve the memory bandwidth throttling heuristic to handle workloads
with not too regular load levels which end up penalized unnecessarily
- Use CPUID to detect the memory bandwidth enforcement limit on AMD
- The usual set of fixes
* tag 'x86_cache_for_v6.9_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (30 commits)
x86/resctrl: Remove lockdep annotation that triggers false positive
x86/resctrl: Separate arch and fs resctrl locks
x86/resctrl: Move domain helper migration into resctrl_offline_cpu()
x86/resctrl: Add CPU offline callback for resctrl work
x86/resctrl: Allow overflow/limbo handlers to be scheduled on any-but CPU
x86/resctrl: Add CPU online callback for resctrl work
x86/resctrl: Add helpers for system wide mon/alloc capable
x86/resctrl: Make rdt_enable_key the arch's decision to switch
x86/resctrl: Move alloc/mon static keys into helpers
x86/resctrl: Make resctrl_mounted checks explicit
x86/resctrl: Allow arch to allocate memory needed in resctrl_arch_rmid_read()
x86/resctrl: Allow resctrl_arch_rmid_read() to sleep
x86/resctrl: Queue mon_event_read() instead of sending an IPI
x86/resctrl: Add cpumask_any_housekeeping() for limbo/overflow
x86/resctrl: Move CLOSID/RMID matching and setting to use helpers
x86/resctrl: Allocate the cleanest CLOSID by searching closid_num_dirty_rmid
x86/resctrl: Use __set_bit()/__clear_bit() instead of open coding
x86/resctrl: Track the number of dirty RMID a CLOSID has
x86/resctrl: Allow RMID allocation to be scoped by CLOSID
x86/resctrl: Access per-rmid structures by index
...
Pull x86 MTRR update from Borislav Petkov:
- Relax the PAT MSR programming which was unnecessarily using the MTRR
programming protocol of disabling the cache around the changes. The
reason behind this is the current algorithm triggering a #VE
exception for TDX guests and unnecessarily complicating things
* tag 'x86_mtrr_for_v6.9_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pat: Simplify the PAT programming protocol
Pull x86 cpu update from Borislav Petkov:
- Have AMD Zen common init code run on all families from Zen1 onwards
in order to save some future enablement effort
* tag 'x86_cpu_for_v6.9_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/CPU/AMD: Do the common init on future Zens too
Pull RAS fixlet from Borislav Petkov:
- Constify yet another static struct bus_type instance now that the
driver core can handle that
* tag 'ras_core_for_v6.9_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Make mce_subsys const
Pull x86 FRED support from Thomas Gleixner:
"Support for x86 Fast Return and Event Delivery (FRED).
FRED is a replacement for IDT event delivery on x86 and addresses most
of the technical nightmares which IDT exposes:
1) Exception cause registers like CR2 need to be manually preserved
in nested exception scenarios.
2) Hardware interrupt stack switching is suboptimal for nested
exceptions as the interrupt stack mechanism rewinds the stack on
each entry which requires a massive effort in the low level entry
of #NMI code to handle this.
3) No hardware distinction between entry from kernel or from user
which makes establishing kernel context more complex than it needs
to be especially for unconditionally nestable exceptions like NMI.
4) NMI nesting caused by IRET unconditionally reenabling NMIs, which
is a problem when the perf NMI takes a fault when collecting a
stack trace.
5) Partial restore of ESP when returning to a 16-bit segment
6) Limitation of the vector space which can cause vector exhaustion
on large systems.
7) Inability to differentiate NMI sources
FRED addresses these shortcomings by:
1) An extended exception stack frame which the CPU uses to save
exception cause registers. This ensures that the meta information
for each exception is preserved on stack and avoids the extra
complexity of preserving it in software.
2) Hardware interrupt stack switching is non-rewinding if a nested
exception uses the currently interrupt stack.
3) The entry points for kernel and user context are separate and GS
BASE handling which is required to establish kernel context for
per CPU variable access is done in hardware.
4) NMIs are now nesting protected. They are only reenabled on the
return from NMI.
5) FRED guarantees full restore of ESP
6) FRED does not put a limitation on the vector space by design
because it uses a central entry points for kernel and user space
and the CPUstores the entry type (exception, trap, interrupt,
syscall) on the entry stack along with the vector number. The
entry code has to demultiplex this information, but this removes
the vector space restriction.
The first hardware implementations will still have the current
restricted vector space because lifting this limitation requires
further changes to the local APIC.
7) FRED stores the vector number and meta information on stack which
allows having more than one NMI vector in future hardware when the
required local APIC changes are in place.
The series implements the initial FRED support by:
- Reworking the existing entry and IDT handling infrastructure to
accomodate for the alternative entry mechanism.
- Expanding the stack frame to accomodate for the extra 16 bytes FRED
requires to store context and meta information
- Providing FRED specific C entry points for events which have
information pushed to the extended stack frame, e.g. #PF and #DB.
- Providing FRED specific C entry points for #NMI and #MCE
- Implementing the FRED specific ASM entry points and the C code to
demultiplex the events
- Providing detection and initialization mechanisms and the necessary
tweaks in context switching, GS BASE handling etc.
The FRED integration aims for maximum code reuse vs the existing IDT
implementation to the extent possible and the deviation in hot paths
like context switching are handled with alternatives to minimalize the
impact. The low level entry and exit paths are seperate due to the
extended stack frame and the hardware based GS BASE swichting and
therefore have no impact on IDT based systems.
It has been extensively tested on existing systems and on the FRED
simulation and as of now there are no outstanding problems"
* tag 'x86-fred-2024-03-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (38 commits)
x86/fred: Fix init_task thread stack pointer initialization
MAINTAINERS: Add a maintainer entry for FRED
x86/fred: Fix a build warning with allmodconfig due to 'inline' failing to inline properly
x86/fred: Invoke FRED initialization code to enable FRED
x86/fred: Add FRED initialization functions
x86/syscall: Split IDT syscall setup code into idt_syscall_init()
KVM: VMX: Call fred_entry_from_kvm() for IRQ/NMI handling
x86/entry: Add fred_entry_from_kvm() for VMX to handle IRQ/NMI
x86/entry/calling: Allow PUSH_AND_CLEAR_REGS being used beyond actual entry code
x86/fred: Fixup fault on ERETU by jumping to fred_entrypoint_user
x86/fred: Let ret_from_fork_asm() jmp to asm_fred_exit_user when FRED is enabled
x86/traps: Add sysvec_install() to install a system interrupt handler
x86/fred: FRED entry/exit and dispatch code
x86/fred: Add a machine check entry stub for FRED
x86/fred: Add a NMI entry stub for FRED
x86/fred: Add a debug fault entry stub for FRED
x86/idtentry: Incorporate definitions/declarations of the FRED entries
x86/fred: Make exc_page_fault() work for FRED
x86/fred: Allow single-step trap and NMI when starting a new task
x86/fred: No ESPFIX needed when FRED is enabled
...
RFDS is a CPU vulnerability that may allow userspace to infer kernel
stale data previously used in floating point registers, vector registers
and integer registers. RFDS only affects certain Intel Atom processors.
Intel released a microcode update that uses VERW instruction to clear
the affected CPU buffers. Unlike MDS, none of the affected cores support
SMT.
Add RFDS bug infrastructure and enable the VERW based mitigation by
default, that clears the affected buffers just before exiting to
userspace. Also add sysfs reporting and cmdline parameter
"reg_file_data_sampling" to control the mitigation.
For details see:
Documentation/admin-guide/hw-vuln/reg-file-data-sampling.rst
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Josh Poimboeuf <jpoimboe@kernel.org>
Currently MMIO Stale Data mitigation for CPUs not affected by MDS/TAA is
to only deploy VERW at VMentry by enabling mmio_stale_data_clear static
branch. No mitigation is needed for kernel->user transitions. If such
CPUs are also affected by RFDS, its mitigation may set
X86_FEATURE_CLEAR_CPU_BUF to deploy VERW at kernel->user and VMentry.
This could result in duplicate VERW at VMentry.
Fix this by disabling mmio_stale_data_clear static branch when
X86_FEATURE_CLEAR_CPU_BUF is enabled.
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Dave Hansen <dave.hansen@linux.intel.com>
KVM VMX changes for 6.9:
- Fix a bug where KVM would report stale/bogus exit qualification information
when exiting to userspace due to an unexpected VM-Exit while the CPU was
vectoring an exception.
- Add a VMX flag in /proc/cpuinfo to report 5-level EPT support.
- Clean up the logic for massaging the passthrough MSR bitmaps when userspace
changes its MSR filter.
Borislav reported that one of his systems has a broken MADT table which
advertises eight present APICs and 24 non-present APICs in the same
package.
The non-present ones are considered hot-pluggable by the topology
evaluation code, which is obviously bogus as there is no way to hot-plug
within the same package.
As the topology evaluation code accounts for hot-pluggable CPUs in a
package, the maximum number of cores per package is computed wrong, which
in turn causes the uncore performance counter driver to access non-existing
MSRs. It will probably confuse other entities which rely on the maximum
number of cores and threads per package too.
Cure this by ignoring hot-pluggable APIC IDs within a present package.
In theory it would be reasonable to just do this unconditionally, but then
there is this thing called reality^Wvirtualization which ruins
everything. Virtualization is the only existing user of "physical" hotplug
and the virtualization tools allow the above scenario. Whether that is
actually in use or not is unknown.
As it can be argued that the virtualization case is not affected by the
issues which exposed the reported problem, allow the bogosity if the kernel
determined that it is running in a VM for now.
Fixes: 89b0f15f40 ("x86/cpu/topology: Get rid of cpuinfo::x86_max_cores")
Reported-by: Borislav Petkov (AMD) <bp@alien8.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/87a5nbvccx.ffs@tglx
The idle routine selection is done on every CPU bringup operation and
has a guard in place which is effective after the first invocation,
which is a pointless exercise.
Invoke it once on the boot CPU and mark the related functions __init.
The guard check has to stay as xen_set_default_idle() runs early.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/r/87edcu6vaq.ffs@tglx
Sparse rightfully complains:
bugs.c:71:9: sparse: warning: incorrect type in initializer (different address spaces)
bugs.c:71:9: sparse: expected void const [noderef] __percpu *__vpp_verify
bugs.c:71:9: sparse: got unsigned long long *
The reason is that x86_spec_ctrl_current which is a per CPU variable is
exported with EXPORT_SYMBOL_GPL().
Use EXPORT_PER_CPU_SYMBOL_GPL() instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20240304005104.732288812@linutronix.de
On UP builds Sparse complains rightfully about accesses to cpu_info with
per CPU accessors:
cacheinfo.c:282:30: sparse: warning: incorrect type in initializer (different address spaces)
cacheinfo.c:282:30: sparse: expected void const [noderef] __percpu *__vpp_verify
cacheinfo.c:282:30: sparse: got unsigned int *
The reason is that on UP builds cpu_info which is a per CPU variable on SMP
is mapped to boot_cpu_info which is a regular variable. There is a hideous
accessor cpu_data() which tries to hide this, but it's not sufficient as
some places require raw accessors and generates worse code than the regular
per CPU accessors.
Waste sizeof(struct x86_cpuinfo) memory on UP and provide the per CPU
cpu_info unconditionally. This requires to update the CPU info on the boot
CPU as SMP does. (Ab)use the weakly defined smp_prepare_boot_cpu() function
and implement exactly that.
This allows to use regular per CPU accessors uncoditionally and paves the
way to remove the cpu_data() hackery.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20240304005104.622511517@linutronix.de
To clean up the per CPU insanity of UP which causes sparse to be rightfully
unhappy and prevents the usage of the generic per CPU accessors on cpu_info
it is necessary to include <linux/percpu.h> into <asm/msr.h>.
Including <linux/percpu.h> into <asm/msr.h> is impossible because it ends
up in header dependency hell. The problem is that <asm/processor.h>
includes <asm/msr.h>. The inclusion of <linux/percpu.h> results in a
compile fail where the compiler cannot longer handle an include in
<asm/cpufeature.h> which references boot_cpu_data which is
defined in <asm/processor.h>.
The only reason why <asm/msr.h> is included in <asm/processor.h> are the
set/get_debugctlmsr() inlines. They are defined there because <asm/processor.h>
is such a nice dump ground for everything. In fact they belong obviously
into <asm/debugreg.h>.
Move them to <asm/debugreg.h> and fix up the resulting damage which is just
exposing the reliance on random include chains.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20240304005104.454678686@linutronix.de
The HV_REGISTER_ are used as arguments to hv_set/get_register(), which
delegate to arch-specific mechanisms for getting/setting synthetic
Hyper-V MSRs.
On arm64, HV_REGISTER_ defines are synthetic VP registers accessed via
the get/set vp registers hypercalls. The naming matches the TLFS
document, although these register names are not specific to arm64.
However, on x86 the prefix HV_REGISTER_ indicates Hyper-V MSRs accessed
via rdmsrl()/wrmsrl(). This is not consistent with the TLFS doc, where
HV_REGISTER_ is *only* used for used for VP register names used by
the get/set register hypercalls.
To fix this inconsistency and prevent future confusion, change the
arch-generic aliases used by callers of hv_set/get_register() to have
the prefix HV_MSR_ instead of HV_REGISTER_.
Use the prefix HV_X64_MSR_ for the x86-only Hyper-V MSRs. On x86, the
generic HV_MSR_'s point to the corresponding HV_X64_MSR_.
Move the arm64 HV_REGISTER_* defines to the asm-generic hyperv-tlfs.h,
since these are not specific to arm64. On arm64, the generic HV_MSR_'s
point to the corresponding HV_REGISTER_.
While at it, rename hv_get/set_registers() and related functions to
hv_get/set_msr(), hv_get/set_nested_msr(), etc. These are only used for
Hyper-V MSRs and this naming makes that clear.
Signed-off-by: Nuno Das Neves <nunodasneves@linux.microsoft.com>
Reviewed-by: Wei Liu <wei.liu@kernel.org>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Link: https://lore.kernel.org/r/1708440933-27125-1-git-send-email-nunodasneves@linux.microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <1708440933-27125-1-git-send-email-nunodasneves@linux.microsoft.com>
These functions are mostly pointless on UP, but nevertheless the
64-bit UP APIC build already depends on the existence of
topology_apply_cmdline_limits_early(), which caused a build bug,
resolve it by making them available under CONFIG_X86_LOCAL_APIC,
as their prototypes already are.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
MKTME repurposes the high bit of physical address to key id for encryption
key and, even though MAXPHYADDR in CPUID[0x80000008] remains the same,
the valid bits in the MTRR mask register are based on the reduced number
of physical address bits.
detect_tme() in arch/x86/kernel/cpu/intel.c detects TME and subtracts
it from the total usable physical bits, but it is called too late.
Move the call to early_init_intel() so that it is called in setup_arch(),
before MTRRs are setup.
This fixes boot on TDX-enabled systems, which until now only worked with
"disable_mtrr_cleanup". Without the patch, the values written to the
MTRRs mask registers were 52-bit wide (e.g. 0x000fffff_80000800) and
the writes failed; with the patch, the values are 46-bit wide, which
matches the reduced MAXPHYADDR that is shown in /proc/cpuinfo.
Reported-by: Zixi Chen <zixchen@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc:stable@vger.kernel.org
Link: https://lore.kernel.org/all/20240131230902.1867092-3-pbonzini%40redhat.com
In commit fbf6449f84 ("x86/sev-es: Set x86_virt_bits to the correct
value straight away, instead of a two-phase approach"), the initialization
of c->x86_phys_bits was moved after this_cpu->c_early_init(c). This is
incorrect because early_init_amd() expected to be able to reduce the
value according to the contents of CPUID leaf 0x8000001f.
Fortunately, the bug was negated by init_amd()'s call to early_init_amd(),
which does reduce x86_phys_bits in the end. However, this is very
late in the boot process and, most notably, the wrong value is used for
x86_phys_bits when setting up MTRRs.
To fix this, call get_cpu_address_sizes() as soon as X86_FEATURE_CPUID is
set/cleared, and c->extended_cpuid_level is retrieved.
Fixes: fbf6449f84 ("x86/sev-es: Set x86_virt_bits to the correct value straight away, instead of a two-phase approach")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc:stable@vger.kernel.org
Link: https://lore.kernel.org/all/20240131230902.1867092-2-pbonzini%40redhat.com
Add a VMX flag in /proc/cpuinfo, ept_5level, so that userspace can query
whether or not the CPU supports 5-level EPT paging. EPT capabilities are
enumerated via MSR, i.e. aren't accessible to userspace without help from
the kernel, and knowing whether or not 5-level EPT is supported is useful
for debug, triage, testing, etc.
For example, when EPT is enabled, bits 51:48 of guest physical addresses
are consumed by the CPU if and only if 5-level EPT is enabled. For CPUs
with MAXPHYADDR > 48, KVM *can't* map all legal guest memory without
5-level EPT, making 5-level EPT support valuable information for userspace.
Reported-by: Yi Lai <yi1.lai@intel.com>
Cc: Tao Su <tao1.su@linux.intel.com>
Cc: Xudong Hao <xudong.hao@intel.com>
Link: https://lore.kernel.org/r/20240110002340.485595-1-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
get_domain_from_cpu() walks a list of domains to find the one that
contains the specified CPU. This needs to be protected against races
with CPU hotplug when the list is modified. It has recently gained
a lockdep annotation to check this.
The lockdep annotation causes false positives when called via IPI as the
lock is held, but by another process. Remove it.
[ bp: Refresh it ontop of x86/cache. ]
Fixes: fb700810d3 ("x86/resctrl: Separate arch and fs resctrl locks")
Reported-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Link: https://lore.kernel.org/all/ZdUSwOM9UUNpw84Y@agluck-desk3
The programming protocol for the PAT MSR follows the MTRR programming
protocol. However, this protocol is cumbersome and requires disabling
caching (CR0.CD=1), which is not possible on some platforms.
Specifically, a TDX guest is not allowed to set CR0.CD. It triggers
a #VE exception.
It turns out that the requirement to follow the MTRR programming
protocol for PAT programming is unnecessarily strict. The new Intel
Software Developer Manual (http://www.intel.com/sdm) (December 2023)
relaxes this requirement, please refer to the section titled
"Programming the PAT" for more information.
In short, this section provides an alternative PAT update sequence which
doesn't need to disable caches around the PAT update but only to flush
those caches and TLBs.
The AMD documentation does not link PAT programming to MTRR and is there
fore, fine too.
The kernel only needs to flush the TLB after updating the PAT MSR. The
set_memory code already takes care of flushing the TLB and cache when
changing the memory type of a page.
[ bp: Expand commit message. ]
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/20240124130650.496056-1-kirill.shutemov@linux.intel.com
The VERW mitigation at exit-to-user is enabled via a static branch
mds_user_clear. This static branch is never toggled after boot, and can
be safely replaced with an ALTERNATIVE() which is convenient to use in
asm.
Switch to ALTERNATIVE() to use the VERW mitigation late in exit-to-user
path. Also remove the now redundant VERW in exc_nmi() and
arch_exit_to_user_mode().
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Link: https://lore.kernel.org/all/20240213-delay-verw-v8-4-a6216d83edb7%40linux.intel.com
resctrl has one mutex that is taken by the architecture-specific code, and the
filesystem parts. The two interact via cpuhp, where the architecture code
updates the domain list. Filesystem handlers that walk the domains list should
not run concurrently with the cpuhp callback modifying the list.
Exposing a lock from the filesystem code means the interface is not cleanly
defined, and creates the possibility of cross-architecture lock ordering
headaches. The interaction only exists so that certain filesystem paths are
serialised against CPU hotplug. The CPU hotplug code already has a mechanism to
do this using cpus_read_lock().
MPAM's monitors have an overflow interrupt, so it needs to be possible to walk
the domains list in irq context. RCU is ideal for this, but some paths need to
be able to sleep to allocate memory.
Because resctrl_{on,off}line_cpu() take the rdtgroup_mutex as part of a cpuhp
callback, cpus_read_lock() must always be taken first.
rdtgroup_schemata_write() already does this.
Most of the filesystem code's domain list walkers are currently protected by
the rdtgroup_mutex taken in rdtgroup_kn_lock_live(). The exceptions are
rdt_bit_usage_show() and the mon_config helpers which take the lock directly.
Make the domain list protected by RCU. An architecture-specific lock prevents
concurrent writers. rdt_bit_usage_show() could walk the domain list using RCU,
but to keep all the filesystem operations the same, this is changed to call
cpus_read_lock(). The mon_config helpers send multiple IPIs, take the
cpus_read_lock() in these cases.
The other filesystem list walkers need to be able to sleep. Add
cpus_read_lock() to rdtgroup_kn_lock_live() so that the cpuhp callbacks can't
be invoked when file system operations are occurring.
Add lockdep_assert_cpus_held() in the cases where the rdtgroup_kn_lock_live()
call isn't obvious.
Resctrl's domain online/offline calls now need to take the rdtgroup_mutex
themselves.
[ bp: Fold in a build fix: https://lore.kernel.org/r/87zfvwieli.ffs@tglx ]
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Babu Moger <babu.moger@amd.com>
Tested-by: Carl Worth <carl@os.amperecomputing.com> # arm64
Link: https://lore.kernel.org/r/20240213184438.16675-25-james.morse@arm.com
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
When a CPU is taken offline the resctrl filesystem code needs to check if it
was the CPU nominated to perform the periodic overflow and limbo work. If so,
another CPU needs to be chosen to do this work.
This is currently done in core.c, mixed in with the code that removes the CPU
from the domain's mask, and potentially free()s the domain.
Move the migration of the overflow and limbo helpers into the filesystem code,
into resctrl_offline_cpu(). As resctrl_offline_cpu() runs before the
architecture code has removed the CPU from the domain mask, the callers need to
be told which CPU is being removed, to avoid picking it as the new CPU. This
uses the exclude_cpu feature previously added.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Babu Moger <babu.moger@amd.com>
Tested-by: Carl Worth <carl@os.amperecomputing.com> # arm64
Link: https://lore.kernel.org/r/20240213184438.16675-24-james.morse@arm.com
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
The resctrl architecture specific code may need to free a domain when a CPU
goes offline, it also needs to reset the CPUs PQR_ASSOC register. Amongst
other things, the resctrl filesystem code needs to clear this CPU from the
cpu_mask of any control and monitor groups.
Currently, this is all done in core.c and called from resctrl_offline_cpu(),
making the split between architecture and filesystem code unclear.
Move the filesystem work to remove the CPU from the control and monitor groups
into a filesystem helper called resctrl_offline_cpu(), and rename the one in
core.c resctrl_arch_offline_cpu().
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Babu Moger <babu.moger@amd.com>
Tested-by: Carl Worth <carl@os.amperecomputing.com> # arm64
Link: https://lore.kernel.org/r/20240213184438.16675-23-james.morse@arm.com
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
The resctrl architecture specific code may need to create a domain when a CPU
comes online, it also needs to reset the CPUs PQR_ASSOC register. The resctrl
filesystem code needs to update the rdtgroup_default CPU mask when CPUs are
brought online.
Currently, this is all done in one function, resctrl_online_cpu(). It will
need to be split into architecture and filesystem parts before resctrl can be
moved to /fs/.
Pull the rdtgroup_default update work out as a filesystem specific cpu_online
helper. resctrl_online_cpu() is the obvious name for this, which means the
version in core.c needs renaming.
resctrl_online_cpu() is called by the arch code once it has done the work to
add the new CPU to any domains.
In future patches, resctrl_online_cpu() will take the rdtgroup_mutex itself.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Babu Moger <babu.moger@amd.com>
Tested-by: Carl Worth <carl@os.amperecomputing.com> # arm64
Link: https://lore.kernel.org/r/20240213184438.16675-21-james.morse@arm.com
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
resctrl reads rdt_alloc_capable or rdt_mon_capable to determine whether any of
the resources support the corresponding features. resctrl also uses the
static keys that affect the architecture's context-switch code to determine the
same thing.
This forces another architecture to have the same static keys.
As the static key is enabled based on the capable flag, and none of the
filesystem uses of these are in the scheduler path, move the capable flags
behind helpers, and use these in the filesystem code instead of the static key.
After this change, only the architecture code manages and uses the static keys
to ensure __resctrl_sched_in() does not need runtime checks.
This avoids multiple architectures having to define the same static keys.
Cases where the static key implicitly tested if the resctrl filesystem was
mounted all have an explicit check now.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Babu Moger <babu.moger@amd.com>
Tested-by: Carl Worth <carl@os.amperecomputing.com> # arm64
Link: https://lore.kernel.org/r/20240213184438.16675-20-james.morse@arm.com
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
The rdt_enable_key is switched when resctrl is mounted, and used to prevent
a second mount of the filesystem. It also enables the architecture's context
switch code.
This requires another architecture to have the same set of static keys, as
resctrl depends on them too. The existing users of these static keys are
implicitly also checking if the filesystem is mounted.
Make the resctrl_mounted checks explicit: resctrl can keep track of whether it
has been mounted once. This doesn't need to be combined with whether the arch
code is context switching the CLOSID.
rdt_mon_enable_key is never used just to test that resctrl is mounted, but does
also have this implication. Add a resctrl_mounted to all uses of
rdt_mon_enable_key.
This will allow the static key changing to be moved behind resctrl_arch_ calls.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Babu Moger <babu.moger@amd.com>
Tested-by: Carl Worth <carl@os.amperecomputing.com> # arm64
Link: https://lore.kernel.org/r/20240213184438.16675-17-james.morse@arm.com
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Depending on the number of monitors available, Arm's MPAM may need to
allocate a monitor prior to reading the counter value. Allocating a
contended resource may involve sleeping.
__check_limbo() and mon_event_count() each make multiple calls to
resctrl_arch_rmid_read(), to avoid extra work on contended systems,
the allocation should be valid for multiple invocations of
resctrl_arch_rmid_read().
The memory or hardware allocated is not specific to a domain.
Add arch hooks for this allocation, which need calling before
resctrl_arch_rmid_read(). The allocated monitor is passed to
resctrl_arch_rmid_read(), then freed again afterwards. The helper
can be called on any CPU, and can sleep.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Babu Moger <babu.moger@amd.com>
Tested-by: Carl Worth <carl@os.amperecomputing.com> # arm64
Link: https://lore.kernel.org/r/20240213184438.16675-16-james.morse@arm.com
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
MPAM's cache occupancy counters can take a little while to settle once the
monitor has been configured. The maximum settling time is described to the
driver via a firmware table. The value could be large enough that it makes
sense to sleep. To avoid exposing this to resctrl, it should be hidden behind
MPAM's resctrl_arch_rmid_read().
resctrl_arch_rmid_read() may be called via IPI meaning it is unable to sleep.
In this case, it should return an error if it needs to sleep. This will only
affect MPAM platforms where the cache occupancy counter isn't available
immediately, nohz_full is in use, and there are no housekeeping CPUs in the
necessary domain.
There are three callers of resctrl_arch_rmid_read(): __mon_event_count() and
__check_limbo() are both called from a non-migrateable context.
mon_event_read() invokes __mon_event_count() using smp_call_on_cpu(), which
adds work to the target CPUs workqueue. rdtgroup_mutex() is held, meaning this
cannot race with the resctrl cpuhp callback. __check_limbo() is invoked via
schedule_delayed_work_on() also adds work to a per-cpu workqueue.
The remaining call is add_rmid_to_limbo() which is called in response to
a user-space syscall that frees an RMID. This opportunistically reads the LLC
occupancy counter on the current domain to see if the RMID is over the dirty
threshold. This has to disable preemption to avoid reading the wrong domain's
value. Disabling preemption here prevents resctrl_arch_rmid_read() from
sleeping.
add_rmid_to_limbo() walks each domain, but only reads the counter on one
domain. If the system has more than one domain, the RMID will always be added
to the limbo list. If the RMIDs usage was not over the threshold, it will be
removed from the list when __check_limbo() runs. Make this the default
behaviour. Free RMIDs are always added to the limbo list for each domain.
The user visible effect of this is that a clean RMID is not available for
re-allocation immediately after 'rmdir()' completes. This behaviour was never
portable as it never happened on a machine with multiple domains.
Removing this path allows resctrl_arch_rmid_read() to sleep if its called with
interrupts unmasked. Document this is the expected behaviour, and add
a might_sleep() annotation to catch changes that won't work on arm64.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Reviewed-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Reviewed-by: Reinette Chatre <reinette.chatre@intel.com>
Reviewed-by: Babu Moger <babu.moger@amd.com>
Tested-by: Shaopeng Tan <tan.shaopeng@fujitsu.com>
Tested-by: Peter Newman <peternewman@google.com>
Tested-by: Babu Moger <babu.moger@amd.com>
Tested-by: Carl Worth <carl@os.amperecomputing.com> # arm64
Link: https://lore.kernel.org/r/20240213184438.16675-15-james.morse@arm.com
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
