The watchdog timer information has been added to all the IPU and DSP
remote processor device nodes in the DRA7xx/AM57xx SoC families. The
data has been added to the two common dra7-ipu-dsp-common and
dra74-ipu-dsp-common dtsi files that can be included by all the
desired board files. The following timers are chosen as the watchdog
timers, as per the usage on the current firmware images:
IPU2: GPTimers 4 & 9 (one for each Cortex-M4 core)
IPU1: GPTimers 7 & 8 (one for each Cortex-M4 core)
DSP1: GPTimer 10
DSP2: GPTimer 13
Each of the IPUs has two Cortex-M4 processors and so uses a timer
each for providing watchdog support on that processor irrespective of
whether the IPU is running in SMP-mode or non-SMP node. The chosen
timers also need to be unique from the ones used by other processors
(regular timers or watchdog timers) so that they can be supported
simultaneously.
The MPU-side drivers will use this data to initialize the watchdog
timer(s), and listen for any watchdog triggers. The BIOS-side code on
these processors needs to configure/refresh the corresponding timer
properly to not throw a watchdog error.
The watchdog timers are optional in general, but are mandatory to
be added to support watchdog error recovery on a particular processor.
These timers can be changed or removed as per the system integration
needs, alongside appropriate equivalent changes on the firmware side.
Signed-off-by: Angela Stegmaier <angelabaker@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for both the IPUs and the
DSP1 remoteproc devices on the AM571x IDK board. These nodes are assigned
to the respective rproc device nodes, and both the IPUs and the DSP1
remote processors are enabled for this board.
The current CMA pools and sizes are defined statically for each device.
The addresses chosen are the same as the respective processors on the
DRA72 EVM board to maintain firmware compatibility between the two boards.
The CMA pools and sizes are defined using 64-bit values to support LPAE.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and this will go away when the remote-side
code has been improved to gather this information runtime during its
initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for all the IPU and DSP
remoteproc devices in the am572x-idk-common.dtsi file that is common to
both the AM572x and AM574x IDK boards. These nodes are assigned to the
respective rproc device nodes, and all the IPU and DSP remote processors
are enabled.
The current CMA pools and sizes are defined statically for each device.
The addresses chosen are the same as the respective processors on
the AM57xx EVM board to maintain firmware compatibility between the
two boards. The CMA pools and sizes are defined using 64-bit values
to support LPAE. The starting addresses are fixed to meet current
dependencies on the remote processor firmwares, and this will go
away when the remote-side code has been improved to gather this
information runtime during its initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for all the IPU and DSP
remoteproc devices on all the AM57xx BeagleBoard-X15 boards. These nodes
are assigned to the respective rproc device nodes, and all the IPU and
DSP remote processors are enabled for all these boards.
The current CMA pools and sizes are defined statically for each device.
The addresses chosen are the same as the respective processors on the
DRA7 EVM board to maintain firmware compatibility between the two boards.
The CMA pools and sizes are defined using 64-bit values to support LPAE.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and this will go away when the remote-side
code has been improved to gather this information runtime during its
initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for all the IPU and
the DSP remoteproc devices on the DRA76 EVM board, and assigned to
the respective rproc device nodes. These match the configuration
used on the DRA7 EVM board. Both the CMA nodes and the corresponding
rproc nodes are also enabled to enable these processors on the
DRA76 EVM board.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for both the IPUs and the
DSP1 remoteproc devices on DRA71 EVM board. These nodes are assigned to
the respective rproc device nodes, and both the IPUs and the DSP1 remote
processors are enabled for this board.
The current CMA pools and sizes are defined statically for each device.
The addresses chosen are the same as the respective processors on the
DRA72 EVM board to maintain firmware compatibility between the two boards.
The CMA pools and sizes are defined using 64-bit values to support LPAE.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and this will go away when the remote-side
code has been improved to gather this information runtime during its
initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for both the IPUs and
the DSP1 remoteproc devices on the DRA72 EVM rev C board, and assigned
to the respective rproc device nodes. These match the configuration
used on the DRA72 EVM board. Both the CMA nodes and the corresponding
rproc nodes are also enabled to enable these processors on the
DRA72 EVM rev C board.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for both the IPUs and the
DSP1 remoteproc devices on DRA72 EVM board. These nodes are assigned to
the respective rproc device nodes, and both the IPUs and the DSP1 remote
processors are enabled for this board.
The current CMA pools and sizes are defined statically for each device.
The addresses chosen are the same as the respective processors on the
DRA7 EVM board to maintain firmware compatibility between the two boards.
The CMA pools and sizes are defined using 64-bit values to support LPAE.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and this will go away when the remote-side
code has been improved to gather this information runtime during its
initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The CMA reserved memory nodes have been added for all the IPU and DSP
remoteproc devices on DRA7 EVM board. These nodes are assigned to the
respective rproc device nodes, and all the IPU and DSP remote processors
are enabled for this board.
The current CMA pools and sizes are defined statically for each device.
The CMA pools and sizes are defined using 64-bit values to support LPAE.
The starting addresses are fixed to meet current dependencies on the
remote processor firmwares, and this will go away when the remote-side
code has been improved to gather this information runtime during its
initialization.
An associated pair of the rproc node and its CMA node can be disabled
later on if there is no use-case defined to use that remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The BIOS System Tick timers have been added for all the IPU and
DSP remoteproc devices in the DRA7 SoC family. The data is added
to the two common dra7-ipu-dsp-common and dra74-ipu-dsp-common
dtsi files that are included by all the desired board files. The
following timers are chosen, as per the timers used on the current
firmware images:
IPU2: GPTimer 3
IPU1: GPTimer 11
DSP1: GPTimer 5
DSP2: GPTimer 6
The timers are optional, but are mandatory to support advanced device
management features such as power management and watchdog support.
The above are added to successfully boot and execute firmware images
configured with the respective timers, images that use internal
processor subsystem timers are not affected. The timers can be
changed or removed as per the system integration needs, if needed.
Each of the IPUs has two Cortex-M4 processors, and is currently
expected to be running in SMP-mode, so only a single timer suffices
to provide the BIOS tick timer. An additional timer should be added
for the second processor in IPU if it were to be run in non-SMP mode.
The timer value also needs to be unique from the ones used by other
processors so that they can be run simultaneously.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the required 'mboxes' property to all the IPU and DSP remote
processors (IPU1, IPU2, DSP1 and DSP2) in the two available common
dtsi files - dra7-ipu-dsp-common and dra74-ipu-dsp-common dtsi files.
The latter file is for platforms having DRA74x/DRA76x/AM572x/AM574x
SoCs which do have a DSP2 processor in addition to the other common
remote processors. The common data is added to the former file, and
the DSP2 only data is added to the latter file.
The mailboxes are required for running the Remote Processor Messaging
(RPMsg) stack between the host processor and each of the remote
processors. Each of the remote processors uses a single sub-mailbox
node, the IPUs are assumed to be running in SMP-mode. The chosen
sub-mailboxes match the values used in the current firmware images.
This can be changed, if needed, as per the system integration needs
after making appropriate changes on the firmware side as well.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The System Mailboxes 5 and 6 and their corresponding child sub-mailbox
(IPC 3.x) nodes are enabled in each of the DRA7xx and AM57xx board
dts files individually at present. These mailboxes enable the Remote
Processor Messaging (RPMsg) communication stack between the MPU host
processor and each of the IPU1, IPU2, DSP1 and DSP2 remote processors.
Move these nodes into two common dtsi files - dra7-ipu-dsp-common and
dra74-ipu-dsp-common files, which are then included in various board
dts files. These files can be used to add all the common configuration
properties (except memory data) required by remote processor nodes.
The memory pools and the remote processor nodes themselves are to be
enabled in the actual board dts files. The first file is to used by
platforms using DRA72x/DRA71x/AM571x/AM570x SoCs, and the second file
is to be used by platforms using DRA74x/DRA76x/AM572x/AM574x SoCs.
The second file includes the first file and contains additional data
only applicable for DSP2 remote processor.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add aliases for all the 3 remote processor nodes common to
all DRA72x/DRA71x/AM571x/AM570x boards. The aliases uses the
stem "rproc", and are defined in the order of the most common
processors on the DRA72x family. The ids are same as DRA74x
except for the missing DSP2.
The aliases can be overridden, if needed, in the respective
derivative board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add aliases for all the IPU and DSP remoteproc processor
nodes common to all DRA74x/DRA76x/AM572x/AM574x boards.
The aliases uses the stem "rproc". The aliases are defined
in the order of the most common processors on the DRA74x
family.
The aliases can be overridden, if needed, in the respective
derivative board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DRA7xx family of SoCs can contain upto two identical DSP
processor subsystems. The second DSP processor subsystem is
present only on the DRA74x/DRA76x variants. The processor
device DT node has therefore been added in disabled state for
this processor subsystem in the DRA74x specific DTS file.
NOTE:
1. The node does not have any mailboxes, timers or CMA region
assigned, they should be added in the respective board dts
files.
2. The node should also be enabled as per the individual product
configuration in the corresponding board dts files.
Signed-off-by: Suman Anna <s-anna@ti.com>
[t-kristo@ti.com: converted to support ti-sysc from legacy hwmod]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DRA7xx family of SOCs have two IPUs and upto two DSP
processor subsystems in general. The IPU processor subsystem
contains dual-core ARM Cortex-M4 processors, while the DSP
processor subsystem is based on the TI's standard TMS320C66x
DSP CorePac core. The IPUs are very similar to those on OMAP5.
Two IPUs and one DSP processor subsystems is the most common
configuration. The processor device DT nodes have been added
for these processor subsystems, with the internal memories
added through 'reg' and 'reg-names' properties. The IPUs only
have an L2 RAM, whereas the DSPs have L1P, L1D and L2 RAM
memories.
NOTE:
1. The nodes do not have any mailboxes, timers or CMA regions
assigned, they should be added in the respective board dts
files.
2. The nodes haven been disabled by default and the enabling
of these nodes is also left to the respective board dts
files.
Signed-off-by: Suman Anna <s-anna@ti.com>
[t-kristo@ti.com: convert to ti-sysc support from legacy hwmod]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With this, the clocksource driver can setup the timers properly.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Clocksource to timer configured in pwm mode can be selected using the DT
property ti,clock-source. There are few pwm timers which are not
selecting the clock source and relying on default value in hardware or
selected by driver. Instead of relying on default value, always select
the clock source from DT.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like using the UART CTS pin does not always trigger for a wake-up
when the SoC is idle.
This is probably because the modem first uses gpio_149 to signal the SoC
that data will be sent, and the CTS will only get used later when the
data transfer is starting.
Let's fix the issue by configuring the gpio_149 pad as the wakeirq for
UART. We have gpio_149 managed by the USB PHY for powering up the right
USB mode, and after that, the gpio gets recycled as the modem wake-up
pin. If needeed, the USB PHY can also later on be configured to use
gpio_149 pad as the wakeirq as a shared irq.
Let's also configure the missing properties for uart-has-rtscts and
current-speed for the modem port while at it. We already configure the
hardware flow control pins with uart1_pins pinctrl setting.
Cc: maemo-leste@lists.dyne.org
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The wlan on droid4 is flakey on some devices, and experiments have shown this
gets fixed if we disable the internal pull for wlan gpio interrupt line.
The symptoms are that the wlan connection is very slow and almost useless
with lots of wlcore firmware reboot warnings in the dmesg.
In addition to configuring the wlan gpio pulls, let's also configure the rest
of the wlan sd pins. We have not configured those eariler as we're booting
using kexec.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The sdmmc1 peripheral is connected on SD-card on STM32MP1-ED1 board.
Add the UHS features the controller is able to manage.
Those features require a level shifter on the board, and the support of
the voltage switch in driver, which is done in Linux v5.7.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Fixes the following warnings for both g5 and g6 SoCs:
arch/arm/boot/dts/aspeed-g5.dtsi:376.19-381.8: Warning
(unit_address_vs_reg): /ahb/apb/lpc@1e789000/lpc-bmc@0/kcs1@0: node
has a unit name, but no reg property
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The AST2600 XDMA engine requires the PCI-E root control reset be cleared
as well, so add a phandle to that syscon reset.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add a node for the XDMA engine with all the necessary information.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add a node for the XDMA engine with all the necessary information.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The Yosemite V2 is a facebook multi-node server
platform that host four OCP server. The BMC
in the Yosemite V2 platform based on AST2500 SoC.
This patch adds linux device tree entry related to
Yosemite V2 specific devices connected to BMC SoC.
Signed-off-by: Manikandan Elumalai <manikandan.hcl.ers.epl@gmail.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Vijay Khemka <vkhemka@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Nicole is an OpenPower machine with an Aspeed 2500 BMC SoC manufactured
by YADRO.
Signed-off-by: Alexander Filippov <a.filippov@yadro.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Patrick Williams <patrick@stwcx.xyz>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Set the bus id for each mux channel to avoid switching channels
multiple times
Signed-off-by: Ben Pai <Ben_Pai@wistron.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Connect the BMP280 and DPS310 to the hwmon subsystem with iio-hwmon
nodes.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The BMC uses reserves the top 16MB of memory for the host to use for VGA
or PCIe communication.
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Name the GPIOs to help userspace work with them. The names describe the
functionality the lines provide, not the net or ball name. This makes it
easier to share userspace code across different systems and makes the
use of the lines more obvious.
Signed-off-by: Andrew Geissler <geisonator@yahoo.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Name the GPIOs to help userspace work with them. The names describe the
functionality the lines provide, not the net or ball name. This makes it
easier to share userspace code across different systems and makes the
use of the lines more obvious.
Signed-off-by: Andrew Geissler <geissonator@yahoo.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Name the GPIOs to help userspace work with them. The names describe the
functionality the lines provide, not the net or ball name. This makes it
easier to share userspace code across different systems and makes the
use of the lines more obvious.
Signed-off-by: Andrew Geissler <geissonator@yahoo.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Name the GPIOs to help userspace work with them. The names describe the
functionality the lines provide, not the net or ball name. This makes it
easier to share userspace code across different systems and makes the
use of the lines more obvious.
Signed-off-by: Andrew Geissler <geissonator@yahoo.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
According to ASPEED, FTTMR010 is not intended to be used in the AST2600.
The arch timer should be used, but Linux doesn't enable high-res timers
without being assured that the arch timer is always on, so set that
property in the devicetree.
The FTTMR010 device is described by set to disabled.
This fixes highres timer support for AST2600.
Fixes: 2ca5646b5c ("ARM: dts: aspeed: Add AST2600 and EVB")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
GPIO Q7 is no longer used for air/water. It is repurposed on Tacoma to
indicate internal FSI (low) vs cabled (high).
GPIO B0 controls the muxing of FSI to the cable (low) or internal pins
(high).
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Change the name of power, fault and rear-id.
Remove the two leds.
Signed-off-by: Ben Pai <Ben_Pai@wistron.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This adds the description of the Power CPUs that are attached to the
BMC.
Without this userspace will see the '/dev/scom66' style layout.
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
