[ Upstream commit 5e76bc677c ]
[Why]
fill_stream_properties_from_drm_display_mode() will not configure pixel
encoding to YCBCR422 when the DRM color format supports YCBCR422 but not
YCBCR420 or YCBCR4444. Instead it will fallback to RGB.
[How]
Add support for YCBCR422 in pixel encoding mapping.
Suggested-by: Mauri Carvalho <mcarvalho3@lenovo.com>
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Mario Limonciello <Mario.Limonciello@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68f3c044f3 ]
[Why]
There is a `scale` sysfs attribute that can be used to indicate when
non-linear brightness scaling is in use. As Custom brightness curves
work by linear interpolation of points the scale is no longer linear.
[How]
Indicate non-linear scaling when custom brightness curves in use and
linear scaling otherwise.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <superm1@kernel.org>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12cdfb61b3 ]
[Why]
dm_mst_get_pbn_divider() returns value integer coming from
the cast from fixed point, but the casted integer will then be used
in dfixed_const to be multiplied by 4096. The cast from fixed point to integer
causes the calculation error becomes bigger when multiplied by 4096.
That makes the calculated pbn_div value becomes smaller than
it should be, which leads to the req_slot number becomes bigger.
Such error is getting reflected in 8k30 timing,
where the correct and incorrect calculated req_slot 62.9 Vs 63.1.
That makes the wrong calculation failed to light up 8k30
after a dock under HBR3 x 4.
[How]
Restore the accuracy by keeping the fraction part
calculated for the left shift operation.
Reviewed-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Fangzhi Zuo <Jerry.Zuo@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c210b757b4 ]
Accessing DC from amdgpu_dm is usually preceded by acquisition of
dc_lock mutex. Most of the DC API that DM calls are under a DC lock.
However, there are a few that are not. Some DC API called from interrupt
context end up sending DMUB commands via a DC API, while other threads were
using DMUB. This was apparent from a race between calls for setting idle
optimization enable/disable and the DC API to set vmin/vmax.
Offload the call to dc_stream_adjust_vmin_vmax() to a thread instead
of directly calling them from the interrupt handler such that it waits
for dc_lock.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
On clients that utilize AMD_PRIVATE_COLOR properties for HDR support,
brightness sliders can include a hardware controlled portion and a
gamma-based portion. This is the case on the Steam Deck OLED when using
gamescope with Steam as a client.
When a user sets a brightness level while HDR is active, the gamma-based
portion and/or hardware portion are adjusted to achieve the desired
brightness. However, when a modeset takes place while the gamma-based
portion is in-use, restoring the hardware brightness level overrides the
user's overall brightness level and results in a mismatch between what
the slider reports and the display's current brightness.
To avoid overriding gamma-based brightness, only restore HW backlight
level after boot or resume. This ensures that the backlight level is
set correctly after the DC layer resets it while avoiding interference
with subsequent modesets.
Fixes: 7875afafba ("drm/amd/display: Fix brightness level not retained over reboot")
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/4551
Signed-off-by: Matthew Schwartz <matthew.schwartz@linux.dev>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit a490c8d77d)
Cc: stable@vger.kernel.org
[Why]
If amdgpu_dm failed to initalize before amdgpu_dm_initialize_drm_device()
completed then freeing atomic_obj will lead to list corruption.
[How]
Check if atomic_obj state is initialized before trying to free.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Ivan Lipski <ivan.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Common resolutions are added to supported modes to enable compatibility
scenarios that compositors may use to do things like clone displays. There
is no guarantee however that the panel will natively support these modes.
[How]
If the compositor hasn't enabled scaling but a non-native resolution has
been picked for an LVDS panel turn the scaler on anyway. This will ensure
compatibility.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Common modes are added to LVDS for compatibility in clone mode, but
not all panels support them. Non-native modes were disabled in the past
but this caused problems because compositors didn't use scaling for non
native modes. Now non-native modes on LVDS will enable the scaler by
default.
[How]
Check the connector type. If the connector is LVDS avoid adding common
modes.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
commit 16dc8bc27c ("drm/amd/display: Export full brightness range to
userspace") adjusted the brightness range to scale to larger values, but
missed updating AMDGPU_MAX_BL_LEVEL which is needed to make sure that
scaling works properly with custom brightness curves.
[How]
As the change for max brightness of 0xFFFF only applies to devices
supporting DC, use existing DC define MAX_BACKLIGHT_LEVEL.
Fixes: 16dc8bc27c ("drm/amd/display: Export full brightness range to userspace")
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://lore.kernel.org/r/20250623171114.1156451-1-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Common modes are added to eDP for compatibility in clone mode, but
not all panels support them. Non-native modes were disabled in the past
but this caused problems because compositors didn't use scaling for non
native modes. Now non-native modes on eDP will enable the scaler by
default.
[How]
Check the connector type. If the connector is eDP avoid adding common
modes.
Reviewed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Common resolutions are added to supported modes to enable compatibility
scenarios that compositors may use to do things like clone displays. There
is no guarantee however that the panel will natively support these modes.
[How]
If the compositor hasn't enabled scaling but a non-native resolution has
been picked for an eDP panel turn the scaler on anyway. This will ensure
compatibility.
Reviewed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When the suspend sequence has been aborted after prepare() but
before suspend() the resume() callback never gets called. The PM core
will call complete() when this happens. As the state has been cached
in prepare() it needs to be destroyed in complete() if it's still around.
[How]
Create a helper for destroying cached state and call it both in resume()
and complete() callbacks. If resume has been called the state will be
destroyed and it's a no-op for complete(). If resume hasn't been called
(such as an aborted suspend) then destroy the state in complete().
Fixes: 50e0bae34f ("drm/amd/display: Add and use new dm_prepare_suspend() callback")
Reviewed-by: Alex Hung <alex.hung@amd.com>
Link: https://lore.kernel.org/r/20250602014432.3538345-4-superm1@kernel.org
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Userspace currently is offered a range from 0-0xFF but the PWM is
programmed from 0-0xFFFF. This can be limiting to some software
that wants to apply greater granularity.
[HOW]
Convert internally to firmware values only when mapping custom
brightness curves because these are in 0-0xFF range. Advertise full
PWM range to userspace.
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Roman Li <roman.li@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
dml2_soc_bb struct can continuously receive updates for future ASICs.
Alignment issues may arise since VBIOS DMCUB contains an older version of
the SOC BB.
Populating the bounding box with values from DMCUB is no longer necessary
since values such as UCLK will be overridden by values acquired by PMFW
anyways.
[HOW]
Use bb_from_dmub to store DCN specific bounding box parameters in DMCUB.
Add helpers to translate DCN specific struct to the corresponding
dml2_soc_bb field.
To avoid alignment issues:
Deprecate applying DMCUB SoC BB for DCN4
For future projects:
Create a flattened struct containing all sensitive parameters in the
bounding box. New parameters can be added to the bottom of the new struct
as needed.
Reviewed-by: Dillon Varone <dillon.varone@amd.com>
Signed-off-by: Austin Zheng <Austin.Zheng@amd.com>
Signed-off-by: Alex Hung <alex.hung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The boolean fast_validate is used as an
input parameter in multiple functions. To
support more scenarios, we are
replacing it with enum dc_validate_mode.
[How]
The enum dc_validate_mode introduces three
possible values:
1) DC_VALIDATE_MODE_AND_PROGRAMMING:
Apply the mode to hardware
2) DC_VALIDATE_MODE_ONLY:
Check whether the mode can be supported
3) DC_VALIDATE_MODE_AND_STATE_INDEX:
Check if the mode can be supported, and
determine the optimal voltage level
needed to support it.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Yan Li <yan.li@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The `drm_*()` print macros will handle including the driver in the print
already. The extra print of the word `amdgpu` is unnecessary.
[How]
Modify all prints to drop `amdgpu: `.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The quantity and duration of FAMS2 commands are set to increase
in future products. This necessitates the implementation of a new
mechanism for chaining commands together, allowing all commands
to be processed within a single transaction.
[How]
The indirect buffer acts as a shared buffer on the driver side,
mapped to DMUB's internal CW7 address. Its source address and
size are sent through mailbox command to DMUB, triggering the
transaction.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Oleh Kuzhylnyi <okuzhyln@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
FAMS is the successor to SubVP starting with DCN4x. Reuse the same
debug option to disable FAMS for debugging purposes.
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It's unnecessary to set operation_result as invalid reply when
p_notify->result != AUX_RET_SUCCESS.
[How]
Set operation_result as p_notify->result to better understand
the reason for the error
Reviewed-by: Ray Wu <ray.wu@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DMI quirks are relatively big code that makes amdgpu_dm 200 lines
larger.
[How]
Move DMI quirks into a dedicated source file and make all quirks
variables for `struct amdgpu_display_manager`.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Now forcing aux->transfer to return 0 when incomplete AUX write is
inappropriate. It should return bytes have been transferred.
[How]
aux->transfer is asked not to change original msg except reply field of
drm_dp_aux_msg structure. Copy the msg->buffer when it's write request,
and overwrite the first byte when sink reply 1 byte indicating partially
written byte number. Then we can return the correct value without
changing the original msg.
Fixes: 3637e457eb ("drm/amd/display: Fix wrong handling for AUX_DEFER case")
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Ray Wu <ray.wu@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Replace all use of DRM_DEBUG_DRIVER in amdgpu_dm.c with
drm_dbg_driver(). The latter prints the instance of the drm device
associated with the error which would helpful in debugging scenarios
involving multiple GPUs
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
amdgpu_dm_process_dmub_aux_transfer_sync() should return all exact data
reply from the sink side. Don't do the analysis job in it.
[How]
Remove unnecessary check condition AUX_TRANSACTION_REPLY_AUX_ACK.
Fixes: ead08b95fa ("drm/amd/display: Fix race condition in DPIA AUX transfer")
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Ray Wu <ray.wu@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
"Request length != reply length" is expected behavior defined in spec.
It's not an invalid reply. Besides, replied data handling logic is not
designed to be written in amdgpu_dm_process_dmub_aux_transfer_sync().
Remove the incorrectly handling section.
Fixes: ead08b95fa ("drm/amd/display: Fix race condition in DPIA AUX transfer")
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Ray Wu <ray.wu@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Defined value of dmub AUX reply command field get updated but didn't
adjust dm receiving side accordingly.
[How]
Check the received reply command value to see if it's updated version
or not. Adjust it if necessary.
Fixes: ead08b95fa ("drm/amd/display: Fix race condition in DPIA AUX transfer")
Cc: Mario Limonciello <mario.limonciello@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Ray Wu <ray.wu@amd.com>
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
FAMS2 expects vmin/vmax to be updated in the case when freesync is
off, but supported. But we only update it when freesync is enabled.
[How]
Change the vsync handler such that dc_stream_adjust_vmin_vmax() its called
irrespective of whether freesync is enabled. If freesync is supported,
then there is no harm in updating vmin/vmax registers.
Closes: https://gitlab.freedesktop.org/drm/amd/-/issues/3546
Reviewed-by: ChiaHsuan Chung <chiahsuan.chung@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Ray Wu <ray.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In certain config, a modeprobe test triggers too many instances of the
error related to infoframe. Make it print only once, and also make it a
warning.
Fixes: 6027cbee19 ("drm/amd/display: Add error check for avi and vendor infoframe setup function")
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Chengjun Yao <Chengjun.Yao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
