RISC-V Devicetrees for v6.5 Part 2
T-Head:
Add a basic dtsi, Kconfig bits & trivial binding additions for the T-Head
1520 SoC (codename "light"). This SoC can be found on the Lichee Pi 4a,
for which a minimal dts is added.
Misc:
Re-sort the dts Makefile to be in alphanumerical order by directory.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.5-pt2' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: sort makefile entries by directory
riscv: defconfig: enable T-HEAD SoC
MAINTAINERS: add entry for T-HEAD RISC-V SoC
riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
riscv: dts: add initial T-HEAD TH1520 SoC device tree
riscv: Add the T-HEAD SoC family Kconfig option
dt-bindings: riscv: Add T-HEAD TH1520 board compatibles
dt-bindings: timer: Add T-HEAD TH1520 clint
dt-bindings: interrupt-controller: Add T-HEAD's TH1520 PLIC
Link: https://lore.kernel.org/r/20230620-fidelity-variety-60b47c889e31@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
RISC-V Devicetrees for v6.5
StarFive:
Watchdog nodes for both the JH7110 & its forerunner, the JH7100. PMU, P
being power, support for the JH7110. PMIC and frequency scaling support
for the JH7110 equipped VisionFive 2.
Most of the DT bits for the JH7110, and the SBCs using it, are pending
support for one of the clock controllers, so it's a smaller set of
changes than I would have hoped for.
Misc:
Pick up some dt-binding cleanup that Palmer assigned to me & had no
uptake from the respective maintainers. My powers of estimation failed
me again, with part of my motivation for picking them up being the
addition of new platforms that ended up not making it. Hopefully next
window for those, as they were relatively close.
Exclude the Allwinner and Renesas subdirectories from the Misc.
MAINTAINERS entry, since I do not take care of those.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.5' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: starfive: Add cpu scaling for JH7110 SoC
riscv: dts: starfive: Enable axp15060 pmic for cpufreq
dt-bindings: interrupt-controller: sifive,plic: Sort compatible values
dt-bindings: timer: sifive,clint: Clean up compatible value section
riscv: dts: starfive: jh7110: Add watchdog node
riscv: dts: starfive: jh7100: Add watchdog node
riscv: dts: starfive: Add PMU controller node
MAINTAINERS: exclude maintained subdirs in RISC-V misc DT entry
Link: https://lore.kernel.org/r/20230612-fasting-floss-0bc05a08bc7a@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
New additions to the list have tried to respect alphanumeric ordering,
but the thing was out of order to start with. Sort it.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Jisheng Zhang <jszhang@kernel.org> says:
Sipeed's Lichee Pi 4A development board uses Lichee Module 4A core
module which is powered by T-HEAD's TH1520 SoC. Add minimal device
tree files for the core module and the development board.
Support basic uart/gpio/dmac drivers, so supports booting to a basic
shell.
This also pulls in -rc2, because of some maintainers re-jigging that
went on in the interim in commit 80e62bc848 ("MAINTAINERS: re-sort
all entries and fields").
Link: https://lore.kernel.org/r/20230617161529.2092-1-jszhang@kernel.org
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Sipeed's Lichee Pi 4A development board uses Lichee Module 4A core
module which is powered by T-HEAD's TH1520 SoC. Add minimal device
tree files for the core module and the development board.
Support basic uart/gpio/dmac drivers, so supports booting to a basic
shell.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Add the operating-points-v2 to support cpu scaling on StarFive JH7110 SoC.
It supports up to 4 cpu frequency loads.
Signed-off-by: Mason Huo <mason.huo@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The VisionFive 2 board has an embedded pmic axp15060,
which supports the cpu DVFS through the dcdc2 regulator.
This patch enables axp15060 pmic and configs the dcdc2.
Signed-off-by: Mason Huo <mason.huo@starfivetech.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Pull ARM SoC devicetree updates from Arnd Bergmann:
"The devicetree changes overall are again dominated by the Qualcomm
Snapdragon platform that weighs in at over 300 changesets, but there
are many updates across other platforms as well, notably Mediatek,
NXP, Rockchips, Renesas, TI, Samsung and ST Microelectronics. These
all add new features for existing machines, as well as new machines
and SoCs.
The newly added SoCs are:
- Allwinner T113-s, an Cortex-A7 based variant of the RISC-V based D1
chip.
- StarFive JH7110, a RISC-V SoC based on the Sifive U74 core like its
JH7100 predecessor, but with additional CPU cores and a GPU.
- Apple M2 as used in current Macbook Air/Pro and Mac Mini gets
added, with comparable support as its M1 predecessor.
- Unisoc UMS512 (Tiger T610) is a midrange smartphone SoC
- Qualcomm IPQ5332 and IPQ9574 are Wi-Fi 7 networking SoCs, based on
the Cortex-A53 and Cortex-A73 cores, respectively.
- Qualcomm sa8775p is an automotive SoC derived from the Snapdragon
family.
Including the initial board support for the added SoC platforms, there
are 52 new machines. The largest group are 19 boards industrial
embedded boards based on the NXP i.MX6 (32-bit) and i.MX8 (64-bit)
families.
Others include:
- Two boards based on the Allwinner f1c200s ultra-low-cost chip
- Three 'Banana Pi' variants based on the Amlogic g12b (A311D, S922X)
SoC.
- The Gl.Inet mv1000 router based on Marvell Armada 3720
- A Wifi/LTE Dongle based on Qualcomm msm8916
- Two robotics boards based on Qualcomm QRB chips
- Three Snapdragon based phones made by Xiaomi
- Five developments boards based on various Rockchip SoCs, including
the rk3588s-khadas-edge2 and a few NanoPi models
- The AM625 Beagleplay industrial SBC
Another 14 machines get removed: both boards for the obsolete 'oxnas'
platform, three boards for the Renesas r8a77950 SoC that were only for
pre-production chips, and various chromebook models based on the
Qualcomm Sc7180 'trogdor' design that were never part of products"
* tag 'soc-dt-6.4' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (836 commits)
arm64: dts: rockchip: Add support for volume keys to rk3399-pinephone-pro
arm64: dts: rockchip: Add vdd_cpu_big regulators to rk3588-rock-5b
arm64: dts: rockchip: Use generic name for es8316 on Pinebook Pro and Rock 5B
arm64: dts: rockchip: Drop RTC clock-frequency on rk3588-rock-5b
arm64: dts: apple: t8112: Add PWM controller
arm64: dts: apple: t600x: Add PWM controller
arm64: dts: apple: t8103: Add PWM controller
arm64: dts: rockchip: Add pinctrl gpio-ranges for rk356x
ARM: dts: nomadik: Replace deprecated spi-gpio properties
ARM: dts: aspeed-g6: Add UDMA node
ARM: dts: aspeed: greatlakes: add mctp device
ARM: dts: aspeed: greatlakes: Add gpio names
ARM: dts: aspeed: p10bmc: Change power supply info
arm64: dts: mediatek: mt6795-xperia-m5: Add Bosch BMM050 Magnetometer
arm64: dts: mediatek: mt6795-xperia-m5: Add Bosch BMA255 Accelerometer
arm64: dts: mediatek: mt6795: Add tertiary PWM node
arm64: dts: rockchip: add panel to Anbernic RG353 series
dt-bindings: arm: Add Data Modul i.MX8M Plus eDM SBC
dt-bindings: arm: fsl: Add chargebyte Tarragon
dt-bindings: vendor-prefixes: add chargebyte
...
Commit 370f696e44 ("dt-bindings: serial: snps-dw-apb-uart: add dma &
dma-names properties") documented dma-names property to handle Allwinner
D1 dtbs_check warnings, but relies on the rx->tx ordering, which is the
reverse of what a bunch of different boards expect.
The initial proposed solution was to allow a flexible dma-names order in
the binding, due to potential ABI breakage concerns after fixing the DTS
files. But luckily the Allwinner boards are not affected, since they are
using a shared DMA channel for rx and tx.
Hence, the first step in fixing the inconsistency was to change
dma-names order in the binding to tx->rx.
Do the same for the snps,dw-apb-uart nodes in the DTS file.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230321215624.78383-7-cristian.ciocaltea@collabora.com
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Merge Hal's series adding support for the new StarFive JH7110 SoC.
There's a few bindings here for core components that were not picked up
by the various maintainers for the subsystems (previously Palmer would
pick these up via the RISC-V tree) & the first two commits in the branch
are shared with the clk tree, since the dts depends on defines in the
dt-binding headers.
This is based on -rc2, as the board does not actually boot on -rc1
due to the bug Linus introduced.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The spi-max-frequency is a property of SPI children, not the
controller:
k210_generic.dtb: spi@50240000: Unevaluated properties are not allowed ('spi-max-frequency' was unexpected)
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The mailbox on PolarFire SoC should really have three reg properties,
not two. Without splitting into three sections, the system controller's
QSPI cannot be accessed as it sits inside the current first range. The
driver & binding have been adapted to account for both two & three
ranges, so fix the dts too.
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The macb on PolarFire SoC has reset support which the generic compatible
does not use. Add the newly introduced MPFS specific compatible as the
primary compatible to avail of this support & wire up the reset to the
clock controllers devicetree entry.
Reviewed-by: Daire McNamara <daire.mcnamara@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Pull SoC DT updates from Arnd Bergmann:
"About a quarter of the changes are for 32-bit arm, mostly filling in
device support for existing machines and adding minor cleanups, mostly
for Qualcomm and Samsung based machines.
Two new 32-bit SoCs are added, both are quad-core Cortex-A7 chips from
Rockchips that have been around for a while but were lacking kernel
support so far: RV1126 is a Vision SoC with an NPU and is used in the
Edgeble Neural Compute Module 2(Neu2) board, while RK3128 is design
for TV boxes and so far only comes with a dts for its refernece
design.
The other 32-bit boards that were added are two ASpeed AST2600 based
BMC boards, the Microchip sam9x60_curiosity development board (Armv5
based!), the Enclustra PE1 FPGA-SoM baseboard, and a few more boards
for i.MX53 and i.MX6ULL.
On the RISC-V side, there are fewer patches, but a total of ten new
single-board computers based on variations of the Allwinner D1/T113
chip, plus one more board based on Microchip Polarfire.
As usual, arm64 has by far the most changes here, with over 700
non-merge changesets, among them over 400 alone for Qualcomm. The
newly added SoCs this time are all recent high-end embedded SoCs for
various markets, each on comes with support for its reference board:
- Qualcomm SM8550 (Snapdragon 8 Gen 2) for mobile phones
- Qualcomm QDU1000/QRU1000 5G RAN platform
- Rockchips RK3588/RK3588s for tablets, chromebooks and SBCs
- TI J784S4 for industrial and automotive applications
In total, there are 46 new arm64 machines:
- Reference platforms for each of the five new SoCs
- Three Amlogic based development boards
- Six embedded machines based on NXP i.MX8MM and i.MX8MP
- The Mediatek mt7986a based Banana Pi R3 router
- Six tablets based on Qualcomm MSM8916 (Snapdragon 410), SM6115
(Snapdragon 662) and SM8250 (Snapdragon 865)
- Two LTE dongles, also based on MSM8916
- Seven mobile phones, based on Qualcomm MSM8953 (Snapdragon 610),
SDM450 and SDM632
- Three chromebooks based on Qualcomm SC7280 (Snapdragon 7c)
- Nine development boards based on Rockchips RK3588, RK3568, RK3566
and RK3328.
- Five development machines based on TI K3 (AM642/AM654/AM68/AM69)
The cleanup of dtc warnings continues across all platforms, adding to
the total number of changes"
* tag 'soc-dt-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (1035 commits)
dt-bindings: riscv: correct starfive visionfive 2 compatibles
ARM: dts: socfpga: Add enclustra PE1 devicetree
dt-bindings: altera: Add enclustra mercury PE1
arm64: dts: qcom: msm8996: align RPM G-Link clock-controller node with bindings
arm64: dts: qcom: qcs404: align RPM G-Link node with bindings
arm64: dts: qcom: ipq6018: align RPM G-Link node with bindings
arm64: dts: qcom: sm8550: remove invalid interconnect property from cryptobam
arm64: dts: qcom: sc7280: Adjust zombie PWM frequency
arm64: dts: qcom: sc8280xp-pmics: Specify interrupt parent explicitly
arm64: dts: qcom: sm7225-fairphone-fp4: enable remaining i2c busses
arm64: dts: qcom: sm7225-fairphone-fp4: move status property down
arm64: dts: qcom: pmk8350: Use the correct PON compatible
arm64: dts: qcom: sc8280xp-x13s: Enable external display
arm64: dts: qcom: sc8280xp-crd: Introduce pmic_glink
arm64: dts: qcom: sc8280xp: Add USB-C-related DP blocks
arm64: dts: qcom: sm8350-hdk: enable GPU
arm64: dts: qcom: sm8350: add GPU, GMU, GPU CC and SMMU nodes
arm64: dts: qcom: sm8350: finish reordering nodes
arm64: dts: qcom: sm8350: move more nodes to correct place
arm64: dts: qcom: sm8350: reorder device nodes
...
RISC-V Devicetrees for v6.3-mw0
Microchip:
A vendor prefix for Aldec and both a binding and Devicetree for the
Aldec TySoM devkit for PolarFire SoC. This Devicetree corresponds to
what they are shipping in the SDK for rev2 boards.
StarFive:
Just the binding for the new StarFive JH7110 SoC and its first-party
SDC the VisionFive 2.
Other:
I was expecting the Devicetree for the aforementioned board to be ready
for this window, as the pinctrl driver had seem some review prior to
v6.2 and both it & the base clock drivers are heavily based on the
existing drivers for the JH7110.
That didn't come to be.. Christmas, the RISC-V Summit in December and
the Lunar New Year all playing a part perhaps.
Because of that, both Palmer and I have the Kconfig.socs work in our
branches, although in hindsight it probably wasn't needed here as I
only added the TySoM Devicetree & the conflict would've been trivial.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.3-mw0' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
riscv: dts: microchip: add the Aldec TySoM's devicetree
dt-bindings: riscv: microchip: document the Aldec TySoM
dt-bindings: vendor-prefixes: Add entry for Aldec
RISC-V: stop directly selecting drivers for SOC_CANAAN
RISC-V: stop selecting SiFive clock and serial drivers directly
RISC-V: stop selecting the PolarFire SoC clock driver
RISC-V: kbuild: convert all use of SOC_FOO to ARCH_FOO
RISC-V: kconfig.socs: convert usage of SOC_CANAAN to ARCH_CANAAN
RISC-V: introduce ARCH_FOO kconfig aliases for SOC_FOO symbols
dt-bindings: riscv: Add StarFive JH7110 SoC and VisionFive 2 board
Link: https://lore.kernel.org/r/Y9LP+Za1h0fkBa58@spud
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The MangoPi MQ is a tiny SBC built around the Allwinner D1s. Its
onboard peripherals include two USB Type-C ports (1 device, 1 host)
and RTL8189FTV WLAN.
A MangoPi MQ-R variant of the board also exists. The MQ-R has a
different form factor, but the onboard peripherals are the same.
Most D1 and D1s boards use a similar power tree, with the 1.8V rail
powered by the SoC's internal LDOA, analog domains powered by ALDO,
and the rest of the board powered by always-on fixed regulators. To
avoid duplication, factor out the regulator information that is
common across boards.
The board also exposes GPIO Port E via a FPC connector, which can
support either a camera or an RMII Ethernet PHY. The additional
regulators supply that connector.
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Guo Ren <guoren@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230126045738.47903-6-samuel@sholland.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
D1 (aka D1-H), D1s (aka F133), R528, and T113 are a family of SoCs based
on a single die, or at a pair of dies derived from the same design.
D1 and D1s contain a single T-HEAD Xuantie C906 CPU, whereas R528 and
T113 contain a pair of Cortex-A7's. D1 and R528 are the full version of
the chip with a BGA package, whereas D1s and T113 are low-pin-count QFP
variants.
Because the original design supported both ARM and RISC-V CPUs, some
peripherals are duplicated. In addition, all variants except D1s contain
a HiFi 4 DSP with its own set of peripherals.
The devicetrees are organized to minimize duplication:
- Common perhiperals are described in sunxi-d1s-t113.dtsi
- DSP-related peripherals are described in sunxi-d1-t113.dtsi
- RISC-V specific hardware is described in sun20i-d1s.dtsi
- Functionality unique to the D1 variant is described in sun20i-d1.dtsi
The SOC_PERIPHERAL_IRQ macro handles the different #interrupt-cells
values between the ARM (GIC) and RISC-V (PLIC) versions of the SoC.
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Heiko Stuebner <heiko.stuebner@vrull.eu>
Tested-by: Heiko Stuebner <heiko.stuebner@vrull.eu>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20230126045738.47903-5-samuel@sholland.org
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
As it says on the tin, add a DT for this board. It's been sitting on my
desk for a while, so may as well have it upstream...
The DT is only partially complete, as it needs the fabric content added.
Unfortunately, I don't have a reference design in RTL or SmartDesign
for it and therefore don't know what that fabric content is.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The TySOM-M-MPFS250 is a compact SoC prototyping board featuring
a Microchip PolarFire SoC MPFS250T-FCG1152. Features include:
- 16 Gib FPGA DDR4
- 16 Gib MSS DDR4 with ECC
- eMMC
- SPI flash memory
- 2x Ethernet 10/100/1000
- USB 2.0
- PCIe x4 Gen2
- HDMI OUT
- 2x FMC connector (HPC and LPC)
Specifically flag this board as rev2, in case later boards have an
FPGA design revision with more features available in the future.
Link: https://www.aldec.com/en/products/emulation/tysom_boards/polarfire_microchip/tysom_m_mpfs250
[Fixed a mistake where I read 16 Gib as 16 GiB!]
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The 32-bit memory resource is needed for non-prefetchable memory
allocations on the PCIe bus, however with some cards (such as the
SM768) the system fails to allocate memory from this.
Checking the allocation against the datasheet, it looks like there
has been a mis-calcualation of the resource for the first memory
region (0x0060090000..0x0070ffffff) which in the data-sheet for
the fu740 (v1p2) is from 0x0060000000..0x007fffffff. Changing
this to allocate from 0x0060090000..0x007fffffff fixes the probing
issues.
Fixes: ae80d51480 ("riscv: dts: Add PCIe support for the SiFive FU740-C000 SoC")
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Greentime Hu <greentime.hu@sifive.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: stable@vger.kernel.org
Tested-by: Ron Economos <re@w6rz.net> # from IRC
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Convert all non user visible use of SOC_FOO symbols to their ARCH_FOO
variants. The canaan DTs are an outlier in that they're gated at the
directory and the file level. Drop the directory level gating while we
are swapping the symbol names over.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Pull ARM SoC DT updates from Arnd Bergmann:
"The devicetree changes contain exactly 1000 non-merge changesets,
including a number of new arm64 SoC variants from Qualcomm and Apple,
as well as the Renesas r9a07g043f/u chip in both arm64 and riscv
variants.
While we have occasionally merged support for non-arm SoCs in the
past, this is now the normal path for riscv devicetree files.
The most notable changes, by SoC platform, are:
- The Apple T6000 (M1 Pro), T6001 (M1 Max) and T6002 (M1 Ultra) chips
now have initial support. This is particularly nice as I am typing
this on a T6002 Mac Studio with only a small number of driver
patches.
- Qualcomm MSM8996 Pro (Snapdragon 821), SM6115 (Snapdragon 662),
SM4250 (Snapdragon 460), SM6375 (Snapdragon 695), SDM670
(Snapdragon 670), MSM8976 (Snapdragon 652) and MSM8956 (Snapdragon
650) are all mobile phone chips that are closely related to others
we already support.
Adding those helps support more phones and we add several models
from Sony (Xperia 10 IV, 5 IV, X, and X compact), OnePlus (One, 3,
3T, and Nord N100), Xiaomi (Poco F1, Mi6), Huawei (Watch) and
Google (Pixel 3a).
There are also new variants of the Herobrine and Trogdor chromebook
motherboards. SA8540P is an automotive SoC used in the Qdrive-3
development platform
- Rockchips gains no new SoC variants, but a lot of new boards: three
mobile gaming systems based on RK3326 Odroid-Go/rg351 family, two
more Anbernic gaming systems based on RK3566 and a number of other
RK356x based single-board computers.
- Renesas RZ/G2UL (r9a07g043) was already supported for arm64, but as
the newly added RZ/Five is based on the same design, this now gets
reorganized in order to share most of the dts description between
the two and add the RZ/Five SMARC EVK board support.
Aside from that, there are the usual changes all over the tree:
- New boards on other platforms contain two ASpeed BMC users, two
Broadcom based Wifi routers, Zyxel NSA310S NAS, the i.MX6 based
Kobo Aura2 ebook reader, two i.MX8 based development boards, two
Uniphier Pro5 development boards, the STM32MP1 testbench board from
DHCOR, the TI K3 based BeagleBone AI-64 board, and the Mediatek
Helio X10 based Sony Xperia M5 phone.
- The Starfive JH7100 source gets reorganized in order to support the
VisionFive V1 board.
- Minor updates and cleanups for Intel SoCFPGA, Marvell PXA168, TI,
ST, NXP, Apple, Broadcom, Juno, Marvell MVEBU, at91, nuvoton,
Tegra, Mediatek, Renesas, Hisilicon, Allwinner, Samsung, ux500,
spear, ... The treewide cleanups now have a lot of fixes for cache
nodes and other binding violoations.
- Somewhat larger sets of reworks for NVIDIA Tegra, Qualcomm and
Renesas platforms, adding a lot more on-chip device support
- A rework of the way that DTB overlays are built"
* tag 'soc-dt-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (979 commits)
arm64: dts: apple: t6002: Fix GPU power domains
arm64: dts: apple: t600x-pmgr: Fix search & replace typo
arm64: dts: apple: Add t8103 L1/L2 cache properties and nodes
arm64: dts: apple: Rename dart-sio* to sio-dart*
arch: arm64: apple: t600x: Use standard "iommu" node name
arch: arm64: apple: t8103: Use standard "iommu" node name
ARM: dts: socfpga: Fix pca9548 i2c-mux node name
dt-bindings: iio: adc: qcom,spmi-vadc: fix PM8350 define
dt-bindings: iio: adc: qcom,spmi-vadc: extend example
arm64: dts: qcom: sc8280xp: fix UFS DMA coherency
arm64: dts: qcom: sc7280: Add DT for sc7280-herobrine-zombie
arm64: dts: qcom: sm8250-sony-xperia-edo: fix no-mmc property for SDHCI
arm64: dts: qcom: sdm845-sony-xperia-tama: fix no-mmc property for SDHCI
arm64: dts: qcom: sda660-inforce-ifc6560: fix no-mmc property for SDHCI
arm64: dts: qcom: sa8155p-adp: fix no-mmc property for SDHCI
arm64: dts: qcom: qrb5165-rb: fix no-mmc property for SDHCI
arm64: dts: qcom: sm8450: align MMC node names with dtschema
arm64: dts: qcom: sc7180-trogdor: use generic node names
arm64: dts: qcom: sm8450-hdk: add sound support
arm64: dts: qcom: sm8450: add Soundwire and LPASS
...
RISC-V DeviceTrees for v6.2
dt-bindings:
- new compatibles to support the StarFive VisionFive & thead CPU cores
- a fix for the PolarFire SoC's pwm binding, merged through my tree as
suggested by the PWM maintainers
Microchip:
- Non-urgent fix for the node address not matches the reg in a way that
the checkers don't complain about
- Add GPIO controlled LEDs for Icicle
- Support for the "CCC" clocks in the FPGA fabric. Previously these
used fixed-frequency clocks in the dt, but if which CCC is in use is
known, as in the v2022.09 Icicle Kit Reference Design, the rates can
be read dynamically. It's an "is known" as it *can* be set via
constraints in the FPGA tooling but does not have to be.
- A fix for the Icicle's pwm-cells
- Removal of some unused PCI clocks
StarFive:
- Addition of the VisionFive DT, which has been a long time coming!
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
* tag 'riscv-dt-for-v6.2-mw0' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux:
dt-bindings: riscv: Add T-HEAD C906 and C910 compatibles
riscv: dts: microchip: remove unused pcie clocks
riscv: dts: microchip: remove pcie node from the sev kit
riscv: dts: microchip: fix the icicle's #pwm-cells
dt-bindings: pwm: fix microchip corePWM's pwm-cells
riscv: dts: starfive: Add StarFive VisionFive V1 device tree
riscv: dts: starfive: Add common DT for JH7100 based boards
dt-bindings: riscv: starfive: Add StarFive VisionFive V1 board
riscv: dts: microchip: fix memory node unit address for icicle
riscv: dts: microchip: icicle: Add GPIO controlled LEDs
riscv: dts: microchip: add the mpfs' fabric clock control
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The PCIe root port in the designs that ship with the PolarBerry and
M100PFSEVP are connected via one, not two Fabric Interface Controllers
(FIC). The one at 0x20_0000_0000 is fic0, so remove the fic1 clocks from
the dt node.
The same clock provides both, so this is harmless but inaccurate.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The SEV kit reference design does not hook up the PCIe root port to the
core complex including it is misleading.
The entry is a re-use mistake - I was not aware of this when I moved
the PCIe node out of mpfs.dtsi so that individual bistreams could
connect it to different fics etc.
The node is disabled, so there should be no functional change here.
Fixes: 978a17d1a6 ("riscv: dts: microchip: add sevkit device tree")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
The VisionFive DT somehow never actually made it upstream, and is
largely shared with the BeagleV. Better late than never.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
\#pwm-cells for the Icicle kit's fabric PWM was incorrectly set to 2 &
blindly overridden by the (out of tree) driver anyway. The core can
support inverted operation, so update the entry to correctly report its
capabilities.
Fixes: 72560c6559 ("riscv: dts: microchip: add fpga fabric section to icicle kit")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
