The devm_clk_get_enabled() helper:
- calls devm_clk_get()
- calls clk_prepare_enable() and registers what is needed in order to
call clk_disable_unprepare() when needed, as a managed resource.
This simplifies the code, the error handling paths and avoid the need of
a dedicated function used with devm_add_action_or_reset().
Based on my test with allyesconfig, this reduces the .o size from:
text data bss dec hex filename
6705 1968 0 8673 21e1 drivers/rtc/rtc-mxc.o
down to:
6212 1968 0 8180 1ff4 drivers/rtc/rtc-mxc.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/1b5ad1877304b01ddbba73ca615274a52f781aa2.1660582728.git.christophe.jaillet@wanadoo.fr
This register would fail to be reset if reading the RTC bias failed for
whichever reason. This commit reorganises the code around to
unconditionally write it back to its previous value, unmap it, and
return the result of regmap_read(), which makes it both simpler and more
correct in the error case.
Signed-off-by: Emmanuel Gil Peyrot <linkmauve@linkmauve.fr>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220823130702.1046-1-linkmauve@linkmauve.fr
To allow new SoCs to use this device without a new compatible string,
use a soc_device_attribute list to define all SoCs affected by the TI
i2327 erratum and require help from their bootloaders to unlock this
device.
Signed-off-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220816173312.23243-2-bb@ti.com
The ACPI_FADT_LOW_POWER_S0 flag merely means that it is better to
use low-power S0 idle on the given platform than S3 (provided that
the latter is supported) and it doesn't preclude using either of
them (which of them will be used depends on the choices made by user
space).
For this reason, there is no benefit from checking that flag in
use_acpi_alarm_quirks().
First off, it cannot be a bug to do S3 with use_acpi_alarm set,
because S3 can be used on systems with ACPI_FADT_LOW_POWER_S0 and it
must work if really supported, so the ACPI_FADT_LOW_POWER_S0 check is
not needed to protect the S3-capable systems from failing.
Second, suspend-to-idle can be carried out on a system with
ACPI_FADT_LOW_POWER_S0 unset and it is expected to work, so if setting
use_acpi_alarm is needed to handle that case correctly, it should be
set regardless of the ACPI_FADT_LOW_POWER_S0 value.
Accordingly, drop the ACPI_FADT_LOW_POWER_S0 check from
use_acpi_alarm_quirks().
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/12054246.O9o76ZdvQC@kreacher
The 12/24hr flag in the RX-8035 can be found in the hour register,
instead of the CTRL1 on the RX-8025. This was overlooked when
support for the RX-8035 was added, and was causing read errors when
the hour register 'overflowed'.
To deal with the relevant register not always being visible in
the relevant functions, determine the 12/24 mode at startup and
store it in the driver state.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Fixes: f120e2e33a ("rtc: rx8025: implement RX-8035 support")
Cc: stable@vger.kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220706074236.24011-1-matt@traverse.com.au
When a remove platform device callback returns an error code, the driver
core emits an error message ("remove callback returned a non-zero value.
This will be ignored.\n") and still removes the device. As the driver
already emits a more specific error message, return 0 to suppress the
core's error message.
This is a preparation for making platform remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Tzung-Bi Shih <tzungbi@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220707153156.214841-1-u.kleine-koenig@pengutronix.de
cppcheck reports
[drivers/rtc/rtc-mpfs.c:219]: (style) Variable 'pending' is assigned a value that is never used.
The fetched CONTROL_REG stored in pending is unused and partially
duplicates the functionality of the later call to mpfs_rtc_clear(). This looks
like leftover development code, so remove pending.
Fixes: 0b31d70359 ("rtc: Add driver for Microchip PolarFire SoC")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220627205943.2075043-1-trix@redhat.com
Introduce support for Texas Instruments Real Time Clock controller on
newer K3 family of SoCs such as AM62x.
The hardware module that is being supported is the "digital only"
version which doesn't have capability of external wakeup sources and
external power backup. However, for many practical applications, this
should suffice as RTC is operational across low power sequences.
The hardware block by itself is split into two distinct domains
internally to further reduce the power consumption with the actual
counter block and comparators clocked off a 32k clock source (which
based on SoC integration can be sourced by an external crystal) and an
register interface block which is driven by the bus clock. While optimal
from power perspective, it does create some complicated synchronizations
and sequences that one must be wary of in the driver handling.
Acked-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Georgi Vlaev <g-vlaev@ti.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220623170808.20998-3-nm@ti.com
All these drivers have an i2c probe function which doesn't use the
"struct i2c_device_id *id" parameter, so they can trivially be
converted to the "probe_new" style of probe with a single argument.
This change was done using the following Coccinelle script, and fixed
up for whitespace changes:
@ rule1 @
identifier fn;
identifier client, id;
@@
- static int fn(struct i2c_client *client, const struct i2c_device_id *id)
+ static int fn(struct i2c_client *client)
{
...when != id
}
@ rule2 depends on rule1 @
identifier rule1.fn;
identifier driver;
@@
struct i2c_driver driver = {
- .probe
+ .probe_new
=
(
fn
|
- &fn
+ fn
)
,
};
Signed-off-by: Stephen Kitt <steve@sk2.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220610162346.4134094-1-steve@sk2.org
The reference manuals of both the RX8803 and RV8803 dictate that
"[On V2F/VLF = ] all registers must be initialized".
The RV-8803 application manual (rev. 1.6) further specifies that crossing
V_LOW2 threshold enables flag V2F and triggers a Power-On reset.
According to table 3.11 in the document, all control registers are
defined to sensible values.
However, The Epson RX-8803 doesn't offer the same guarantees.
It explicitly states:
During the initial power-up, the TEST bit is reset to "0" and the VLF
bit is set to "1".
∗ At this point, all other register values are _undefined_, so be sure to
perform a reset before using the module.
Commit d3700b6b64 ("rtc: rv8803: Stop the clock while setting the time")
also had this rationale:
Indeed, all the registers must be initialized if the voltage has been
lower than VLOW2 (triggering V2F), but not low enough to trigger a POR.
We should follow the advice and initialize all applicable registers.
We can group the registers into 3 groups:
A) Already correctly handled registers:
* 0B-0Ch | Timer Counter | unused and disabled by clearing TE in 0Dh
* 0Dh | Extension Reg | already initialized in rv8803_regs_configure
* 0Eh | Flag Reg | handled in IRQ handler, except for VLF, VDET
* 0Eh | VLF, VDET | cleared in ->set_time
* 10h | 100th Seconds | Already reset via RESET bit
* 20-21h | Capture Buffer | holds timestamp unused by driver
* 2Fh | Event Control | resets automatically
B) Registers that are hardware initialized on POR, but not on VLF:
* 0Fh | Control Reg
* 2Ch | OSC Offset
C) RAM that is undefined on voltage loss:
* 00-06h | Date/Time
* 07h | RAM
* 08-0Ah | Alarm
This means we should initialize after VLF the registers in group B
(RV8803_CTRL and RV8803_OSC_OFFSET).
Group C is all-zero after voltage loss on the RV-8803, but undefined on
the RX-8803. This is ok for Date/Time because ->get_time returns an
error code for as long as the voltage loss flag is active. It's cleared
on ->set_time however. Zeroing both RAM and alarm ensures a fixed value
is read afterwards.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220426071056.1187235-4-s.hauer@pengutronix.de
Pull more ARM multiplatform updates from Arnd Bergmann:
"The second part of the multiplatform changes now converts the
Intel/Marvell PXA platform along with the rest. The patches went
through several rebases before the merge window as bugs were found, so
they remained separate.
This has to touch a lot of drivers, in particular the touchscreen,
pcmcia, sound and clk bits, to detach the driver files from the
platform and board specific header files"
* tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
ARM: pxa/mmp: remove traces of plat-pxa
ARM: pxa: convert to multiplatform
ARM: pxa/sa1100: move I/O space to PCI_IOBASE
ARM: pxa: remove support for MTD_XIP
ARM: pxa: move mach/*.h to mach-pxa/
ARM: PXA: fix multi-cpu build of xsc3
ARM: pxa: move plat-pxa to drivers/soc/
ARM: mmp: rename pxa_register_device
ARM: mmp: remove tavorevb board support
ARM: pxa: remove unused mach/bitfield.h
ARM: pxa: move clk register definitions to driver
ARM: pxa: move smemc register access from clk to platform
cpufreq: pxa3: move clk register access to clk driver
ARM: pxa: remove get_clk_frequency_khz()
ARM: pxa: pcmcia: move smemc configuration back to arch
ASoC: pxa: i2s: use normal MMIO accessors
ASoC: pxa: ac97: use normal MMIO accessors
ASoC: pxa: use pdev resource for FIFO regs
Input: wm97xx - get rid of irq_enable method in wm97xx_mach_ops
Input: wm97xx - switch to using threaded IRQ
...
Pull RTC updates from Alexandre Belloni:
"A new driver represents the bulk of the changes and then we get the
usual small fixes.
New driver:
- Renesas RZN1 rtc
Drivers:
- sun6i: Add nvmem support"
* tag 'rtc-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: mxc: Silence a clang warning
rtc: rzn1: Fix a variable type
rtc: rzn1: Fix error code in probe
rtc: rzn1: Avoid mixing variables
rtc: ftrtc010: Fix error handling in ftrtc010_rtc_probe
rtc: mt6397: check return value after calling platform_get_resource()
rtc: rzn1: fix platform_no_drv_owner.cocci warning
rtc: gamecube: Add missing iounmap in gamecube_rtc_read_offset_from_sram
rtc: meson: Fix email address in MODULE_AUTHOR
rtc: simplify the return expression of rx8025_set_offset()
rtc: pcf85063: Add a compatible entry for pca85073a
dt-binding: pcf85063: Add an entry for pca85073a
MAINTAINERS: Add myself as maintainer of the RZN1 RTC driver
rtc: rzn1: Add oscillator offset support
rtc: rzn1: Add alarm support
rtc: rzn1: Add new RTC driver
dt-bindings: rtc: rzn1: Describe the RZN1 RTC
rtc: sun6i: Add NVMEM provider
In the ->set_offset() callback, the 'val' variable is used for two
different purposes at the same time, which is oviously wrong:
- It contains the intermediate value of the SUBU register that must be
written at the end of ->set_offset().
- It is used in the middle of the above calculations to poll the CTL2
register for a specific value.
Let's introduce a 'ctl2' variable just for the readl_poll_timeout()
call and use it there in place of 'var'.
In order to avoid mixing those two variables again, let's rename the
remaining occurences of 'val' into 'subu' and initialize it to 0 to
avoid the uninitialized variable situation reported by Tom Rix and Colin
Ian King already.
Fixes: be4a11cf98 ("rtc: rzn1: Add oscillator offset support")
Reported-by: Tom Rix <trix@redhat.com>
Reported-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220520082221.488849-1-miquel.raynal@bootlin.com
Pull m68k updates from Geert Uytterhoeven:
- Introduce virtual m68k machine based on Android Goldfish devices
- defconfig updates
- Minor fixes and improvements
* tag 'm68k-for-v5.19-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: atari: Make Atari ROM port I/O write macros return void
m68k: math-emu: Fix dependencies of math emulation support
m68k: math-emu: Fix typos in comments
m68k: Wire up syscall_trace_enter/leave for m68k
m68k: defconfig: Update defconfigs for v5.18-rc1
m68k: Introduce a virtual m68k machine
clocksource/drivers: Add a goldfish-timer clocksource
rtc: goldfish: Use gf_ioread32()/gf_iowrite32()
tty: goldfish: Introduce gf_ioread32()/gf_iowrite32()
In the error handling path, the clk_prepare_enable() function
call should be balanced by a corresponding 'clk_disable_unprepare()'
call , as already done in the remove function.
clk_disable_unprepare calls clk_disable() and clk_unprepare().
They will use IS_ERR_OR_NULL to check the argument.
Fixes: ac05fba39c ("rtc: gemini: Add optional clock handling")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220403054912.31739-1-linmq006@gmail.com
The RZN1 RTC can compensate the imprecision of the oscillator up to
approximately 190ppm.
Seconds can last slightly shorter or longer depending on the
configuration.
Below ~65ppm of correction, we can change the time spent in a second
every minute, which is the most accurate compensation that the RTC can
offer. Above, the compensation will be active every 20s.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20220516082504.33913-5-miquel.raynal@bootlin.com
