[why]
MES response time in sriov may be longer than default value
due to reset or init in other VF. A timeout value specific
to sriov is needed.
[how]
When in sriov, adjust the timeout value to calculated
worst case scenario.
Signed-off-by: Yiqing Yao <yiqing.yao@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
0, original pstate X
1, ctx_A_create -> ctx_A->stable_pstate = X
2, ctx_A_set_pstate (Y) -> current pstate is Y (PEAK or STANDARD)
3, ctx_B_create -> ctx_B->stable_pstate = Y
4, ctx_A_destroy -> restore pstate to X
5, ctx_B_destroy -> restore pstate to Y
Above sequence will cause final pstate is wrong (Y), should be original X.
[HOW]
When ctx_B create,
if ctx_A touched pstate setting
(not auto, stable_pstate_ctx != NULL),
set ctx_B->stable_pstate the same value as ctx_A saved,
if stable_pstate_ctx == NULL,
fetch current pstate to fill
ctx_B->stable_pstate.
Signed-off-by: Chengming Gui <Jack.Gui@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit 8795e182b0 ("PCI/portdrv: Don't disable AER reporting in get_port_device_capability()")
uncovered a bug in amdgpu that required a reordering of the driver
init sequence to avoid accessing a special register on the GPU
before it was properly set up leading to an PCI AER error. This
reordering uncovered a different hw programming ordering dependency
in some APUs where the SDMA doorbells need to be programmed before
the GFX doorbells. To fix this, move the SDMA doorbell programming
back into the soc15 common code, but use the actual doorbell range
values directly rather than the values stored in the ring structure
since those will not be initialized at this point.
This is a partial revert, but with the doorbell assignment
fixed so the proper doorbell index is set before it's used.
Fixes: e3163bc8ff ("drm/amdgpu: move nbio sdma_doorbell_range() into sdma code for vega")
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: skhan@linuxfoundation.org
Cc: stable@vger.kernel.org
The fb_base in struct drm_mode_config has been unused for a long time.
Some drivers set it and some don't leading to a very confusing state
where the variable can't be relied upon, because there's no indication
as to which driver sets it and which doesn't.
The only usage of fb_base is internal to two drivers so instead of trying
to force it into all the drivers to get it into a coherent state
completely remove it.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Thomas Zimmermann <tzimemrmann@suse.de>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221019024401.394617-1-zack@kde.org
A user reported a bug on CAPE VERDE system where uvd_v3_1
IP component failed to initialize as there is an issue with
BO move code from one memory to other.
In function amdgpu_mem_visible() called by amdgpu_bo_move(),
when there are no blocks to compare or if we have a single
block then break the loop.
Fixes: 312b4dc11d ("drm/amdgpu: Fix VRAM BO swap issue")
Signed-off-by: Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If mes is not dequeued during fini, mes will be in an uncleaned state
during reload, then mes couldn't receive some commands which leads to
reload failure.
[How]
Perform MES dequeue via MMIO after all the unmap jobs are done by mes
and before kiq fini.
v2: Move the dequeue operation inside kiq_hw_fini.
Signed-off-by: YuBiao Wang <YuBiao.Wang@amd.com>
Reviewed-by: Jack Xiao <Jack.Xiao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- refactor mode2 on v11.0.7 to align with aldebaran
- comment out using mode2 reset as default for now, will introduce
another controller to replace previous reset_level_mask
v2: squash in unused variable removal (Alex)
Signed-off-by: Victor Zhao <Victor.Zhao@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit dac6b80818.
This commit reverted the AMDGPU_SKIP_MODE2_RESET as it conflicts with
the original design of reset handler. Will redesign it.
Fixes: dac6b80818 ("drm/amdgpu: let mode2 reset fallback to default when failure")
Signed-off-by: Victor Zhao <Victor.Zhao@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 5bd8d53f6f.
This commit breaks the reset logic for aldebaran, revert it for now.
Will move the mask inside the reset handler.
Fixes: 5bd8d53f6f ("drm/amdgpu: add debugfs amdgpu_reset_level")
Signed-off-by: Victor Zhao <Victor.Zhao@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For asic with VF MMIO access protection avoid using CPU for VM table updates.
CPU pagetable updates have issues with HDP flush as VF MMIO access protection
blocks write to mmBIF_BX_DEV0_EPF0_VF0_HDP_MEM_COHERENCY_FLUSH_CNTL register
during sriov runtime.
v3: introduce virtualization capability flag AMDGPU_VF_MMIO_ACCESS_PROTECT
which indicates that VF MMIO write access is not allowed in sriov runtime
Signed-off-by: Danijel Slivka <danijel.slivka@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A user reported a bug on CAPE VERDE system where uvd_v3_1
IP component failed to initialize as there is an issue with
BO move code from one memory to other.
In function amdgpu_mem_visible() called by amdgpu_bo_move(),
when there are no blocks to compare or if we have a single
block then break the loop.
Fixes: 312b4dc11d ("drm/amdgpu: Fix VRAM BO swap issue")
Signed-off-by: Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If mes is not dequeued during fini, mes will be in an uncleaned state
during reload, then mes couldn't receive some commands which leads to
reload failure.
[How]
Perform MES dequeue via MMIO after all the unmap jobs are done by mes
and before kiq fini.
v2: Move the dequeue operation inside kiq_hw_fini.
Signed-off-by: YuBiao Wang <YuBiao.Wang@amd.com>
Reviewed-by: Jack Xiao <Jack.Xiao@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
kmap() is being deprecated in favor of kmap_local_page().
There are two main problems with kmap(): (1) It comes with an overhead as
mapping space is restricted and protected by a global lock for
synchronization and (2) it also requires global TLB invalidation when the
kmap’s pool wraps and it might block when the mapping space is fully
utilized until a slot becomes available.
With kmap_local_page() the mappings are per thread, CPU local, can take
page faults, and can be called from any context (including interrupts).
It is faster than kmap() in kernels with HIGHMEM enabled. Furthermore,
the tasks can be preempted and, when they are scheduled to run again, the
kernel virtual addresses are restored and are still valid.
Since its use in amdgpu/amdgpu_ttm.c is safe, it should be preferred.
Therefore, replace kmap() with kmap_local_page() in amdgpu/amdgpu_ttm.c.
Suggested-by: Ira Weiny <ira.weiny@intel.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
RAS error address translation algorithm is common
across dGPU and A + A platform as along as the SOC
integrates the same generation of UMC IP.
UMC RAS is managed by x86 MCA on A + A platform,
umc_ras in GPU driver is not initialized at all on
A + A platform. In such case, any umc_ras callback
implemented for dGPU config shouldn't be invoked
from A + A specific callback.
The change moves convert_error_address out of dGPU
umc_ras structure and makes it share between A + A
and dGPU config.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Stanley Yang <Stanley.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- refactor mode2 on v11.0.7 to align with aldebaran
- comment out using mode2 reset as default for now, will introduce
another controller to replace previous reset_level_mask
v2: squash in unused variable removal (Alex)
Signed-off-by: Victor Zhao <Victor.Zhao@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit dac6b80818.
This commit reverted the AMDGPU_SKIP_MODE2_RESET as it conflicts with
the original design of reset handler. Will redesign it.
Fixes: dac6b80818 ("drm/amdgpu: let mode2 reset fallback to default when failure")
Signed-off-by: Victor Zhao <Victor.Zhao@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 5bd8d53f6f.
This commit breaks the reset logic for aldebaran, revert it for now.
Will move the mask inside the reset handler.
Fixes: 5bd8d53f6f ("drm/amdgpu: add debugfs amdgpu_reset_level")
Signed-off-by: Victor Zhao <Victor.Zhao@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For asic with VF MMIO access protection avoid using CPU for VM table updates.
CPU pagetable updates have issues with HDP flush as VF MMIO access protection
blocks write to mmBIF_BX_DEV0_EPF0_VF0_HDP_MEM_COHERENCY_FLUSH_CNTL register
during sriov runtime.
v3: introduce virtualization capability flag AMDGPU_VF_MMIO_ACCESS_PROTECT
which indicates that VF MMIO write access is not allowed in sriov runtime
Signed-off-by: Danijel Slivka <danijel.slivka@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
After commit 571c053658 ("drm/amdgpu: switch sdma buffer function
tear down to a helper"), the variable 'ring' is not used anymore, it
can be removed.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pull more drm updates from Dave Airlie:
"Round of fixes for the merge window stuff, bunch of amdgpu and i915
changes, this should have the gcc11 warning fix, amongst other
changes.
amdgpu:
- DC mutex fix
- DC SubVP fixes
- DCN 3.2.x fixes
- DCN 3.1.x fixes
- SDMA 6.x fixes
- Enable DPIA for 3.1.4
- VRR fixes
- VRAM BO swapping fix
- Revert dirty fb helper change
- SR-IOV suspend/resume fixes
- Work around GCC array bounds check fail warning
- UMC 8.10 fixes
- Misc fixes and cleanups
i915:
- Round to closest in g4x+ HDMI clock readout
- Update MOCS table for EHL
- Fix PSR_IMR/IIR field handling
- Fix watermark calculations for gen12+/DG2 modifiers
- Reject excessive dotclocks early
- Fix revocation of non-persistent contexts
- Handle migration for dpt
- Fix display problems after resume
- Allow control over the flags when migrating
- Consider DG2_RC_CCS_CC when migrating buffers"
* tag 'drm-next-2022-10-14' of git://anongit.freedesktop.org/drm/drm: (110 commits)
drm/amd/display: Add HUBP surface flip interrupt handler
drm/i915/display: consider DG2_RC_CCS_CC when migrating buffers
drm/i915: allow control over the flags when migrating
drm/amd/display: Simplify bool conversion
drm/amd/display: fix transfer function passed to build_coefficients()
drm/amd/display: add a license to cursor_reg_cache.h
drm/amd/display: make virtual_disable_link_output static
drm/amd/display: fix indentation in dc.c
drm/amd/display: make dcn32_split_stream_for_mpc_or_odm static
drm/amd/display: fix build error on arm64
drm/amd/display: 3.2.207
drm/amd/display: Clean some DCN32 macros
drm/amdgpu: Add poison mode query for umc v8_10_0
drm/amdgpu: Update umc v8_10_0 headers
drm/amdgpu: fix coding style issue for mca notifier
drm/amdgpu: define convert_error_address for umc v8.7
drm/amdgpu: define RAS convert_error_address API
drm/amdgpu: remove check for CE in RAS error address query
drm/i915: Fix display problems after resume
drm/amd/display: fix array-bounds error in dc_stream_remove_writeback() [take 2]
...
Update all SDMA versions that support SR-IOV to properly
tear down the ttm buffer functions on suspend.
Tested-by: Bokun Zhang <Bokun.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Switch all of the SDMA implementations to use the helper to
tear down the ttm buffer manager.
Tested-by: Bokun Zhang <Bokun.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
