[ Upstream commit dd9e329af7 ]
The datasheet describes the following initialization flow including
minimum delay times between each step:
1. DSI data lanes need to be in LP-11 and the clock lane in HS mode
2. toggle EN signal
3. initialize registers
4. enable PLL
5. soft reset
6. enable DSI stream
7. check error status register
To meet this requirement we need to make sure the host bridge's
pre_enable() is called first by using the pre_enable_prev_first
flag.
Furthermore we need to split enable() into pre_enable() which covers
steps 2-5 from above and enable() which covers step 7 and is called
after the host bridge's enable().
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Fixes: ceb515ba29 ("drm/bridge: ti-sn65dsi83: Add TI SN65DSI83 and SN65DSI84 driver")
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> #TQMa8MxML/MBa8Mx
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230503163313.2640898-3-frieder@fris.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1464e48d69 ]
During probe, the driver registers i2c dummy devices and populates the
aux bus, which registers a device for the panel. After doing that, the
driver can still defer probe if needed. This ordering of operations is
troublesome however, because the deferred probe work will retry probing
all pending devices every time a new device is registered. Therefore, if
modules need to be loaded in order to satisfy the dependencies for this
driver to complete probe, the kernel will stall, since it'll keep trying
to probe the anx7625 driver, but never succeed, given that modules would
only be loaded after the deferred probe work completes.
Two changes are required to avoid this issue:
* Move of_find_mipi_dsi_host_by_node(), which can defer probe, to before
anx7625_register_i2c_dummy_clients() and
devm_of_dp_aux_populate_ep_devices(), which register devices.
* Make use of the done_probing callback when populating the aux bus,
so that the bridge registration is only done after the panel is
probed. This is required because the panel might need to defer probe,
but the aux bus population needs the i2c dummy devices working, so
this call couldn't just be moved to an earlier point in probe.
One caveat is that if the panel is described outside the aux bus, the
probe loop issue can still happen, but we don't have a way to avoid
it in that case since there's no callback available.
With this patch applied, it's possible to boot on
mt8192-asurada-spherion with
CONFIG_DRM_ANALOGIX_ANX7625=y
CONFIG_MTK_MMSYS=m
CONFIG_BACKLIGHT_PWM=y
and also with
CONFIG_DRM_ANALOGIX_ANX7625=y
CONFIG_MTK_MMSYS=y
CONFIG_BACKLIGHT_PWM=m
Fixes: adca62ec37 ("drm/bridge: anx7625: Support reading edid through aux channel")
Fixes: 269332997a ("drm/bridge: anx7625: Return -EPROBE_DEFER if the dsi host was not found")
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230518193902.891121-1-nfraprado@collabora.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bac7842cd1 ]
Correct computation of THS_TRAILCNT register.
This register must be set to a value that ensure that
THS_TRAIL > 60 ns + 4 x UI
and
THS_TRAIL > 8 x UI
and
THS_TRAIL < TEOT
with
TEOT = 105 ns + (12 x UI)
with the actual value of THS_TRAIL being
(1 + THS_TRAILCNT) x ByteClk cycle + ((1 to 2) + 2) xHSBYTECLK cycle +
- (PHY output delay)
with PHY output delay being about
(8 + (5 to 6)) x MIPIBitClk cycle in the BitClk conversion.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-9-francesco@dolcini.it
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77a089328d ]
Correct computation of THS_ZEROCNT register.
This register must be set to a value that ensure that
THS_PREPARE + THS_ZERO > 145ns + 10*UI
with the actual value of (THS_PREPARE + THS_ZERO) being
((1 to 2) + 1 + (TCLK_ZEROCNT + 1) + (3 to 4)) x ByteClk cycle +
+ HSByteClk x (2 + (1 to 2)) + (PHY delay)
with PHY delay being about
(8 + (5 to 6)) x MIPIBitClk cycle in the BitClk conversion.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-7-francesco@dolcini.it
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75a8aeac25 ]
Always enable HS video mode setting the TXMD bit, without this change no
video output is present with DSI sinks that are setting
MIPI_DSI_MODE_LPM flag (tested with LT8912B DSI-HDMI bridge).
Previously the driver was enabling HS mode only when the DSI sink was
not explicitly setting the MIPI_DSI_MODE_LPM, however this is not
correct.
The MIPI_DSI_MODE_LPM is supposed to indicate that the sink is willing
to receive data in low power mode, however clearing the
TC358768_DSI_CONTROL_TXMD bit will make the TC358768 send video in
LP mode that is not the intended behavior.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-2-francesco@dolcini.it
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee0285e134 ]
When dynamically switching lanes was removed, the intent of the code
was to check to make sure that higher speed items used 4 lanes, but
it had the unintended consequence of removing the slower speeds for
4-lane users.
This attempts to remedy this by doing a check to see that the
max frequency doesn't exceed the chip limit, and a second
check to make sure that the max bit-rate doesn't exceed the
number of lanes * max bit rate / lane.
Fixes: 9a0cdcd664 ("drm/bridge: adv7533: remove dynamic lane switching from adv7533 bridge")
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230319125524.58803-1-aford173@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Pull drm updates from Dave Airlie:
"There are a bunch of changes all over in the usual places.
Highlights:
- habanalabs moves from misc to accel
- first accel driver for Intel VPU (Versatile Processing Unit)
inference engine
- dropped all the ancient legacy DRI1 drivers. I think it's been at
least 10 years since anyone has heard about these.
- Intel DG2 updates and prelim Meteorlake enablement
- etnaviv adds support for Versilicon NPU device (a GPU like engine
with inference accelerators)
Detailed summary:
Removals:
- remove legacy dri1 drivers: i810, mga, r128, savage, sis, tdfx, via
New driver:
- intel VPU accelerator driver
- habanalabs comes via drm tree now
drm/core:
- use drm_dbg_ helpers in several places
- Document defaults for CRTC backgrounds
- Document use of drm_minor
edid:
- improve mode parsing and refactoring
connector:
- support analog TV mode property
media:
- add some common formats
udmabuf:
- add vmap/vunmap methods
fourcc:
- add XRGB1555 and RGB565 formats
- document open source user waiver
firmware:
- fix color-format selection for system framebuffer
format-helper:
- Add conversion from XRGB8888 to various sysfb formats
- Make XRGB8888 the only driver-emulated legacy format
- Add conversion from XRGB8888 to XBGR8888 and ABGR8888
fb-helper:
- fix preferred depth and bpp values across drivers
- Avoid blank consoles from selecting an incorrect color format
probe-helper:
- Enable/disable HPD on connectors
scheduler:
- Fix lockup in drm_sched_entity_kill()
- Deprecate drm_sched_resubmit_jobs()
bridge:
- remove unused functions
- implement i2c probe_new in various drivers
- ite-it6505: Locking fixes, Cache EDID data
- ite-it66121: Support IT6610 chip
- lontium-tl9611: Fix HDMI on DragonBoard 845c
- parade-ps8640: Use atomic bridge functions
- Support i.MX93 LDB plus DT bindings
debugfs:
- add per device helpers and convert drivers
displayport:
- mst fixes
- add DP adaptive sync DPCD definitions
fbdev:
- always pick 32bpp as default
- remove some unused code
simpledrm:
- support system memory framebuffers
panel:
- add orientation quirks for Lenovo Yoga Tab 3 X90F and DynaBook K50
- Use ktime_get_boottime() to measure power-down delay
- Fix auto-suspend delay
- Visionox VTDR6130 AMOLED DSI
- Support Himax HX8394
- Convert many drivers to common generic DSI write-sequence helper
- AUO A030JTN01
ttm:
- drop bo wait wrapper
- fix MIPS build
habanalabs:
- moved driver to accel subsystem
- gaudi2 decoder error improvement
- more trace events
- Gaudi2 abrupt reset by firmware support
- add uAPI to flush memory transactions
- add uAPI to pass through userspace reqs to fw
- remove dma-buf export by handle
amdgpu:
- add new INFO queries for peak and min sclk/mclk for profile modes
- Add PCIe info to the INFO IOCTL
- secure display support for multiple displays
- DML optimizations
- DCN 3.2 updates
- PSR updates
- DP 2.1 updates
- SR-IOV RAS updates
- VCN RAS support
- SMU 13.x updates
- Switch 1 element arrays to flexible arrays
- Add RAS support for DF 4.3
- Stack size improvements
- S0ix rework
- Allow 0 as a vram limit on APUs
- Handle profiling modes for SMU13.x
- Fix possible segfault in failure case
- Rework FW requests to happen in early_init for all IPs so that we
don't lose the sbios console if FW is missing
- Fix power reporting on certain firmwares for CZN/RN
- Allow S0ix without BIOS support
- Enable freesync over PCon
- Re-enable the AGP aperture on GMC 11.x
amdkfd:
- Error handling fixes
- PASID fixes
- Fix for cleared VRAM BOs
- Fix cleanup if GPUVM creation fails
- Memory accounting fix
- Use resource_size rather than open codeing it
- GC11 mGPU fix
radeon:
- Switch 1 element arrays to flexible arrays
- Fix memory leak on shutdown
- move to new logging
i915:
- Meteorlake display/OA/GSC fw/workarounds enabling
- DP MST DSC support
- Gamma/degamma readout support for the state checker
- Enable SDP split support for DP 2.0
- Add probe blocking support to i915.force_probe parameter
- Enable Xe HP 4tile support
- Avoid display direct calls to uncore
- Fix HuC delayed load memory leaks
- Add DG2 workarounds Wa_18018764978 and Wa_18019271663
- Improve suspend / resume times with VT-d scanout workaround active
- Fix DG2 visual corruption on small BAR systems by not forgetting to
copy CCS aux state
- Fix TLB invalidation for Gen12.50 video and compute engines
- Enable HF-EEODB by switching HDMI, DP and LVDS to use struct
drm_edid
- Start using unversioned DMC firmware paths for new platforms
- ELD refactor: Stop using hardware buffer, precompute ELD
- lots of display code refactoring
nouveau:
- drop legacy ioctl support
- replace 0-sized array
msm:
- dpu/dsi/mdss: Support for SM8350, SM8450 SM8550 and SC8280XP platform
- Added bindings for SM8150
- dpu: Partial support for DSC on SM8150 and SM8250
- dpu: Fixed color transformation matrix being lost on suspend/resume
- dp: Support SDM845 and SC8280XP platforms
- dp: Support for limiting DP link rate via DT property
- dsi: Validate display modes according to the DSI OPP table
- dsi: DSI PHY support for the SM6375 platform
- Add MSM_SUBMIT_BO_NO_IMPLICI
- a2xx: Support to load legacy firmware
- a6xx: GPU devcore dump updates for a650/a660
- GPU devfreq tuning and fixes
- Turn 8960 HDMI PHY into clock provider,
- Make 8960 HDMI PHY use PXO clock from DT
etnaviv:
- experimental versilicon NPU support
- report GPU load via fdinfo format
- MMU fault message improvements
tegra:
- rework syncpoint interrupt
mediatek:
- DSI timing fix
- fix config deps
ast:
- various fixes
exynos:
- restore bridge chain order fixes
gud:
- convert to shadow plane buffers
- perform flushing synchronously during atomic update
- Use new debugfs helpers
arm/hdlcd:
- Use new debugfs helper
ili9486:
- Support 16-bit pixel data
imx:
- Split off IPUv3 driver
mipi-dbi:
- convert to DRM shadow-plane helpers
- rsp driver changes
- Support separate I/O-voltage supply
mxsfb:
- Depend on ARCH_MXS or ARCH_MXC
sun4i:
- convert to new TV mode property
vc4:
- convert to new TV mode property
- kunit tests
- Support RGB565 and RGB666 formats
- convert dsi driver to bridge
- Various HVS an CRTC fixes
v3d:
- Do not opencode drm_gem_object_lookup()
virtio:
- improve tracing
vkms:
- support small cursors in IGT tests
- Fix SEGFAULT from incorrect GEM-buffer mapping
rcar-du:
- fixes and improvements"
* tag 'drm-next-2023-02-23' of git://anongit.freedesktop.org/drm/drm: (1455 commits)
msm/fbdev: fix unused variable warning with clang.
drm/fb-helper: Remove drm_fb_helper_unprepare() from drm_fb_helper_fini()
dma-buf: make kobj_type structure constant
drm/shmem-helper: Fix locking for drm_gem_shmem_get_pages_sgt()
drm/amd/display: disable SubVP + DRR to prevent underflow
drm/amd/display: Fail atomic_check early on normalize_zpos error
drm/amd/pm: avoid unaligned access warnings
drm/amd/display: avoid unaligned access warnings
drm/amd/display: Remove duplicate/repeating expressions
drm/amd/display: Remove duplicate/repeating expression
drm/amd/display: Make variables declaration inside ifdef guard
drm/amd/display: Fix excess arguments on kernel-doc
drm/amd/display: Add previously missing includes
drm/amd/amdgpu: Add function prototypes to headers
drm/amd/display: Add function prototypes to headers
drm/amd/display: Turn global functions into static
drm/amd/display: remove unused _calculate_degamma_curve function
drm/amd/display: remove unused func declaration from resource headers
drm/amd/display: unset initial value for tf since it's never used
drm/amd/display: camel case cleanup in color_gamma file
...
Enable the drm bridge pre_enable_prev_first flag so that the
previous bridge pre_enable should be called first before the
pre_enable for the tc358764 bridge is called.
This makes sure that the previous bridge should be initialized
properly before the tc358764 bridge is powered up.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Same to i.MX8mp LDB, i.MX93 LDB is controlled by mediamix blk-ctrl
through LDB_CTRL and LVDS_CTRL registers. i.MX93 LDB supports only
one LVDS channel(channel 0) and it's LVDS_CTRL register bit1 is used
as LVDS_EN instead of CH1_EN. Add i.MX93 LDB support in the existing
i.MX8mp LDB bridge driver by adding i.MX93 LDB compatible string and
device data(to reflect different register offsets and LVDS_CTRL register
bit1 definition).
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230123021449.969243-3-victor.liu@nxp.com
Backmerging into drm-misc-next to get DRM accelerator infrastructure,
which is required by ipuv driver.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
drm-misc-next for v6.3:
UAPI Changes:
* fourcc: Document Open Source user waiver
Cross-subsystem Changes:
* firmware: fix color-format selection for system framebuffers
Core Changes:
* format-helper: Add conversion from XRGB8888 to various sysfb formats;
Make XRGB8888 the only driver-emulated legacy format
* fb-helper: Avoid blank consoles from selecting an incorrect color format
* probe-helper: Enable/disable HPD on connectors plus driver updates
* Use drm_dbg_ helpers in several places
* docs: Document defaults for CRTC backgrounds; Document use of drm_minor
Driver Changes:
* arm/hdlcd: Use new debugfs helpers
* gud: Use new debugfs helpers
* panel: Support Visionox VTDR6130 AMOLED DSI; Support Himax HX8394; Convert
many drivers to common generic DSI write-sequence helper
* v3d: Do not opencode drm_gem_object_lookup()
* vc4: Various HVS an CRTC fixes
* vkms: Fix SEGFAULT from incorrect GEM-buffer mapping
* Convert various drivers to i2c probe_new()
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/Y8ADeSzZDj+tpibF@linux-uq9g
drm-misc-next for v6.3:
UAPI Changes:
* connector: Support analog-TV mode property
* media: Add MEDIA_BUS_FMT_RGB565_1X24_CPADHI,
MEDIA_BUS_FMT_RGB666_1X18 and MEDIA_BUS_FMT_RGB666_1X24_CPADHI
Cross-subsystem Changes:
* dma-buf: Documentation fixes
* i2c: Introduce i2c_client_get_device_id() helper
Core Changes:
* Improve support for analog TV output
* bridge: Remove unused drm_bridge_chain functions
* debugfs: Add per-device helpers and convert various DRM drivers
* dp-mst: Various fixes
* fbdev emulation: Always pick 32 bpp as default
* KUnit: Add tests for managed helpers; Various cleanups
* panel-orientation: Add quirks for Lenovo Yoga Tab 3 X90F and DynaBook K50
* TTM: Open-code ttm_bo_wait() and remove the helper
Driver Changes:
* Fix preferred depth and bpp values throughout DRM drivers
* Remove #CONFIG_PM guards throughout DRM drivers
* ast: Various fixes
* bridge: Implement i2c's probe_new in various drivers; Fixes; ite-it6505:
Locking fixes, Cache EDID data; ite-it66121: Support IT6610 chip,
Cleanups; lontium-tl9611: Fix HDMI on DragonBoard 845c; parade-ps8640:
Use atomic bridge functions
* gud: Convert to DRM shadow-plane helpers; Perform flushing synchronously
during atomic update
* ili9486: Support 16-bit pixel data
* imx: Split off IPUv3 driver; Various fixes
* mipi-dbi: Convert to DRM shadow-plane helpers plus rsp driver changes;i
Support separate I/O-voltage supply
* mxsfb: Depend on ARCH_MXS or ARCH_MXC
* omapdrm: Various fixes
* panel: Use ktime_get_boottime() to measure power-down delay in various
drivers; Fix auto-suspend delay in various drivers; orisetech-ota5601a:
Add support
* sprd: Cleanups
* sun4i: Convert to new TV-mode property
* tidss: Various fixes
* v3d: Various fixes
* vc4: Convert to new TV-mode property; Support Kunit tests; Cleanups;
dpi: Support RGB565 and RGB666 formats; dsi: Convert DSI driver to
bridge
* virtio: Improve tracing
* vkms: Support small cursors in IGT tests; Various fixes
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/Y7QIwlfElAYWxRcR@linux-uq9g
Pull pwm updates from Thierry Reding:
"Various changes across the board, mostly improvements and cleanups"
* tag 'pwm/for-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (42 commits)
pwm: pca9685: Convert to i2c's .probe_new()
pwm: sun4i: Propagate errors in .get_state() to the caller
pwm: Handle .get_state() failures
pwm: sprd: Propagate errors in .get_state() to the caller
pwm: rockchip: Propagate errors in .get_state() to the caller
pwm: mtk-disp: Propagate errors in .get_state() to the caller
pwm: imx27: Propagate errors in .get_state() to the caller
pwm: cros-ec: Propagate errors in .get_state() to the caller
pwm: crc: Propagate errors in .get_state() to the caller
leds: qcom-lpg: Propagate errors in .get_state() to the caller
drm/bridge: ti-sn65dsi86: Propagate errors in .get_state() to the caller
pwm/tracing: Also record trace events for failed API calls
pwm: Make .get_state() callback return an error code
pwm: pxa: Enable for MMP platform
pwm: pxa: Add reference manual link and limitations
pwm: pxa: Use abrupt shutdown mode
pwm: pxa: Remove clk enable/disable from pxa_pwm_config
pwm: pxa: Set duty cycle to 0 when disabling PWM
pwm: pxa: Remove pxa_pwm_enable/disable
pwm: mediatek: Add support for MT7986
...
