USDHC IP has one limitation: the tuning circuit can't handle the async
sdio device interrupt correctly. When sdio device use 4 data lines,
async sdio interrupt will use the shared DAT[1], if enable auto tuning
circuit to check these 4 data lines, include the DAT[1], this circuit
will detect this interrupt, take this as data on DAT[1], and adjust the
delay cell wrongly, finally will cause the DATA/CMD CRC error.
So for SDIO device, only enable DAT[0] and CMD line for auto tuning.
To distinguish the card type during card init, involve init_card().
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20221223025022.1893102-3-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
For standard tuning method on usdhc, the previous tuning result can
impact current tuning result, let current tuning can't set the correct
delay cell. And from the logic, this is also reasonable for manual
tuning method. So reset the tuning logic before execute tuning.
To avoid compile issue, this patch also move the esdhc_reset_tuning()
upper.
Find this issue when support SDIO WiFi in band wakeup feature. After
system resume back, will do re-tuning, but then meet data CRC error.
Do not meet this issue on SD/eMMC, because we already call
esdhc_reset_tuning() when config the legency ios, and SD/eMMC need
to re-init when system resume back, but SDIO device don't do re-init
if it has MMC_PM_KEEP_POWER pm_flags.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1666947869-7904-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
[[ NOTE: this is completely untested by the author, but included solely
because, as noted in commit df57d73276 ("mmc: sdhci-pci: Fix
SDHCI_RESET_ALL for CQHCI for Intel GLK-based controllers"), "other
drivers using CQHCI might benefit from a similar change, if they
also have CQHCI reset by SDHCI_RESET_ALL." We've now seen the same
bug on at least MSM, Arasan, and Intel hardware. ]]
SDHCI_RESET_ALL resets will reset the hardware CQE state, but we aren't
tracking that properly in software. When out of sync, we may trigger
various timeouts.
It's not typical to perform resets while CQE is enabled, but this may
occur in some suspend or error recovery scenarios.
Include this fix by way of the new sdhci_and_cqhci_reset() helper.
This patch depends on (and should not compile without) the patch
entitled "mmc: cqhci: Provide helper for resetting both SDHCI and
CQHCI".
Fixes: bb6e358169 ("mmc: sdhci-esdhc-imx: add CMDQ support")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20221026124150.v4.4.I7d01f9ad11bacdc9213dee61b7918982aea39115@changeid
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To reset standard tuning circuit completely, after clear ESDHC_MIX_CTRL_EXE_TUNE,
also need to clear bit buffer_read_ready, this operation will finally clear the
USDHC IP internal logic flag execute_tuning_with_clr_buf, make sure the following
normal data transfer will not be impacted by standard tuning logic used before.
Find this issue when do quick SD card insert/remove stress test. During standard
tuning prodedure, if remove SD card, USDHC standard tuning logic can't clear the
internal flag execute_tuning_with_clr_buf. Next time when insert SD card, all
data related commands can't get any data related interrupts, include data transfer
complete interrupt, data timeout interrupt, data CRC interrupt, data end bit interrupt.
Always trigger software timeout issue. Even reset the USDHC through bits in register
SYS_CTRL (0x2C, bit28 reset tuning, bit26 reset data, bit 25 reset command, bit 24
reset all) can't recover this. From the user's point of view, USDHC stuck, SD can't
be recognized any more.
Fixes: d9370424c9 ("mmc: sdhci-esdhc-imx: reset tuning circuit when power on mmc card")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/1634263236-6111-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
As indicated by function esdhc_change_pinstate(), SDR50 and DDR50
require pins_100mhz, while SDR104 and HS400 require pins_200mhz. Some
system design may support SDR50 and DDR50 with 100mhz pin state only
(without 200mhz one). Currently the combined 100/200 MHz pinctrl state
check prevents such system from running SDR50 and DDR50. Separate the
check to support such system design.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/20210326110214.28416-1-shawnguo@kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In current code, we add 1ms dealy after each tuning command for standard
tuning method. Adding this 1ms dealy is because USDHC default check the
CMD CRC and DATA line. If detect the CMD CRC, USDHC standard tuning
IC logic do not wait for the tuning data sending out by the card, trigger
the buffer read ready interrupt immediately, and step to next cycle. So
when next time the new tuning command send out by USDHC, card may still
not send out the tuning data of the upper command，then some eMMC cards
may stuck, can't response to any command, block the whole tuning procedure.
If do not check the CMD CRC for tuning, then do not has this issue. USDHC
will wait for the tuning data of each tuning command and check them. If the
tuning data pass the check, it also means the CMD line also okay for tuning.
So this patch disable the CMD CRC check for tuning, save some time for the
whole tuning procedure.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/1590488522-9292-2-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add support for host software queue for (e)MMC/SD
- Throttle polling rate for CMD6
- Update CMD13 busy condition check for CMD6 commands
- Improve busy detect polling for erase/trim/discard/HPI
- Fixup support for HW busy detection for HPI commands
- Re-work and improve support for eMMC sanitize commands
MMC host:
- mmci:
* Add support for sdmmc variant revision 2.0
- mmci_sdmmc:
* Improve support for busyend detection
* Fixup support for signal voltage switch
* Add support for tuning with delay block
- mtk-sd:
* Fix another SDIO irq issue
- sdhci:
* Disable native card detect when GPIO based type exist
- sdhci:
* Add option to defer request completion
- sdhci_am654:
* Add support to set a tap value per speed mode
- sdhci-esdhc-imx:
* Add support for i.MX8MM based variant
* Fixup support for standard tuning on i.MX8 usdhc
* Optimize for strobe/clock dll settings
* Fixup support for system and runtime suspend/resume
- sdhci-iproc:
* Update regulator/bus-voltage management for bcm2711
- sdhci-msm:
* Prevent clock gating with PWRSAVE_DLL on broken variants
* Fix management of CQE during SDHCI reset
- sdhci-of-arasan:
* Add support for auto tuning on ZynqMP based platforms
- sdhci-omap:
* Add support for system suspend/resume
- sdhci-sprd:
* Add support for HW busy detection
* Enable support host software queue
- sdhci-tegra:
* Add support for HW busy detection
- tmio/renesas_sdhi:
* Enforce retune after runtime suspend
- renesas_sdhi:
* Use manual tap correction for HS400 on some variants
* Add support for manual correction of tap values for tunings"
* tag 'mmc-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (86 commits)
mmc: cavium-octeon: remove nonsense variable coercion
mmc: mediatek: fix SDIO irq issue
mmc: mmci_sdmmc: Fix clear busyd0end irq flag
dt-bindings: mmc: Fix node name in an example
mmc: core: Re-work the code for eMMC sanitize
mmc: sdhci: use FIELD_GET for preset value bit masks
mmc: sdhci-of-at91: Display clock changes for debug purpose only
mmc: sdhci: iproc: Add custom set_power() callback for bcm2711
mmc: sdhci: am654: Use sdhci_set_power_and_voltage()
mmc: sdhci: at91: Use sdhci_set_power_and_voltage()
mmc: sdhci: milbeaut: Use sdhci_set_power_and_voltage()
mmc: sdhci: arasan: Use sdhci_set_power_and_voltage()
mmc: sdhci: Introduce sdhci_set_power_and_bus_voltage()
mmc: vub300: Use scnprintf() for avoiding potential buffer overflow
dt-bindings: mmc: synopsys-dw-mshc: fix clock-freq-min-max in example
sdhci: tegra: Enable MMC_CAP_WAIT_WHILE_BUSY host capability
sdhci: tegra: Implement Tegra specific set_timeout callback
mmc: sdhci-omap: Add Support for Suspend/Resume
mmc: renesas_sdhi: simplify execute_tuning
mmc: renesas_sdhi: Use BITS_PER_LONG helper
...
Currently, when use standard tuning, driver default disable DMA just before
send tuning command. But on i.MX8 usdhc, this is not enough. Need also clear
DMA_SEL. If not, once the DMA_SEL select AMDA2 before, even dma already disabled,
when send tuning command, usdhc will still prefetch the ADMA script from wrong
DMA address, then we will see IOMMU report some error which show lack of TLB
mapping.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1582100757-20683-7-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Since L4.15, community involve the commit 105819c8a5 ("mmc: core: use mrq->sbc
when sending CMD23 for RPMB"), let the usdhc to decide whether to use ACMD23 for
RPMB. This CMD23 for RPMB need to set the bit 31 to its argument, if not, the
RPMB write operation will return general fail.
According to the sdhci logic, SDMA mode will disable the ACMD23, and only in
ADMA mode, it will chose to use ACMD23 if the host support. But according to
debug, and confirm with IC, the imx6qpdl/imx6sx/imx6sl/imx7d do not support
the ACMD23 feature completely. These SoCs only use the 16 bit block count of
the register 0x4 (BLOCK_ATT) as the CMD23's argument in ACMD23 mode, which
means it will ignore the upper 16 bit of the CMD23's argument. This will block
the reliable write operation in RPMB, because RPMB reliable write need to set
the bit31 of the CMD23's argument. This is the hardware limitation. So for
imx6qpdl/imx6sx/imx6sl/imx7d, it need to broke the ACMD23 for eMMC, SD card do
not has this limitation, because SD card do not support reliable write.
For imx6ul/imx6ull/imx6sll/imx7ulp/imx8, it support the ACMD23 completely, it
change to use the 0x0 register (DS_ADDR) to put the CMD23's argument in ADMA mode.
This patch add a new flag ESDHC_FLAG_BROKEN_AUTO_CMD23, and add this flag to
imx6q/imx6sx/imx6sl/imx7d, and due to the imx6sll share the same compatible string
with imx6sx before, and imx6sll do not has this limitation, so add a new compatible
string for imx6sll.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1582100757-20683-4-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
After set the STROBE SLV delay target value, it need to wait some
time to let the usdhc lock the REF and SLV clock. In normal case,
1~2us is enough for imx8/imx6 and imx7d, and 4~5us is enough for
imx7ulp, but when do reboot stress test or do the bind/unbind stress
test, sometimes need to wait about 10us to get the status lock.
This patch optimize delay handle method, only print the warning
message if the status is still not lock after 1ms delay.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1582100757-20683-3-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
strobe-dll-delay-target is the delay cell add on the strobe line.
Strobe line the the uSDHC loopback read clock which is use in HS400
mode. Different strobe-dll-delay-target may need to set for different
board/SoC. If this delay cell is not set to an appropriate value,
we may see some read operation meet CRC error after HS400 mode select
which already pass the tuning.
This patch add the strobe-dll-delay-target setting in driver, so that
user can easily config this delay cell in dts file.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1582100757-20683-1-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When pm_runtime_suspend is run, a call to SCFW power off the SS (SS is a
power domain, usdhc belong to this SS power domain) in which the resource
resides is made. The SCFW can power off the SS if no other resource in
active in that SS. If so, all state associated with all the resources within
the SS that is powered off is lost, this includes the clock rates, clock state
etc. When pm_runtime_resume is called, the SS associated with that resource
is powered up. But the clocks are left in the default state.
This patch restore clock rate in pm_runtime_resume, make sure the
clock is right rather than depending on the default state setting
by SCFW.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/1582100563-20555-5-git-send-email-haibo.chen@nxp.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
