Add the vendor commands that must be used by the network manager
to allow proper operation of iwlmei.
* Send information on the AP CSME is connected to
* Notify the userspace when roaming is forbidden
* Allow the userspace to require ownership
Co-Developed-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
v6: remove the VENDOR_CMDS Kconfig option and make the whole infra
depend on IWLMEI directly
v7: remove // comments
remove an unneeded function
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211112062814.7502-5-emmanuel.grumbach@intel.com
iwlmei needs to know about the follwing events:
* Association
* De-association
* Country Code change
* SW Rfkill change
* SAR table changes
iwlmei can take the device away from us, so report the new
rfkill type when this happens.
Advertise the required data from the CSME firmware to the
usersapce: mostly, the AP that the CSME firmware is currently
associated to in case there is an active link protection
session.
Generate the HOST_ASSOC / HOST_DISSASSOC messages.
Don't support WPA1 (non-RSNA) for now.
Don't support shared wep either.
We can then determine the AUTH parameter by checking the AKM.
Feed the cipher from the key installation.
SW Rfkill will be implemented later when cfg80211 will
allow us to read the SW Rfkill state.
Co-Developed-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
v7: Ayala added her signed-off
remove pointless function declaration
fix a bug due to merge conflict in the HOST_ASSOC message
v8: leave a print if we have a SAP connection on a device we do
not support (yet)
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211112062814.7502-4-emmanuel.grumbach@intel.com
When we receive an association response, a significant amount
of time might have passed since we sent the corresponding
association request (mac80211 will wait up to 500ms for the TX
and then 100ms for the response after ACK was received). But
the time event is touched only when we send the assoc request,
so it might not have much time remaining, more easily causing
the (dreaded)
No beacon heard and the session protection is over already...
message.
Refactor iwl_mvm_mac_mgd_prepare_tx() and split out a new
function iwl_mvm_protect_assoc(), and call it on successful
association to extend the time event to the minimum time if
necessary.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211024181719.411c174d9e5e.I03c701c2e9e6788f34546e538264763db0ab30ef@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When auth/assoc completes, we should remove session protection,
except when association is successful, where we need it until a
beacon is received from the AP.
In particular, in the case of assoc comeback, currently the session
protection event just times out, leading to confusing messages:
wlan0: 42:00:00:00:00:00 rejected association temporarily; comeback duration 1000 TU (1024 ms)
iwlwifi 0000:00:00.0: Not associated and the session protection is over already...
wlan0: Connection to AP 42:00:00:00:00:00 lost
wlan0: associate with 42:00:00:00:00:00 (try 2/3)
mac80211 never does anything on the "Connection ... lost" as it's
not even connected.
Removing the session protection when it's no longer needed removes
those confusing messages and lets the device do other things in the
allocated time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20211017162352.95e4bebb069b.I635280e5d26c70414ac6eb5d62b46fe4bd942818@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Johannes berg says:
====================
Lots of changes:
* aggregation handling improvements for some drivers
* hidden AP discovery on 6 GHz and other HE 6 GHz
improvements
* minstrel improvements for no-ack frames
* deferred rate control for TXQs to improve reaction
times
* virtual time-based airtime scheduler
* along with various little cleanups/fixups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When we have a P2P Device active, we attempt to only change the
PHY context it uses when we get a new remain-on-channel, if the
P2P Device is the only user of the PHY context.
This is fine if we're switching within a band, but if we're
switching bands then the switch implies a removal and re-add
of the PHY context, which isn't permitted by the firmware while
it's bound to an interface.
Fix the code to skip the unbind/release/... cycle only if the
band doesn't change (or we have old devices that can switch the
band on the fly as well.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210612142637.e9ac313f70f3.I713b9d109957df7e7d9ed0861d5377ce3f8fccd3@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When doing scan while 6GHz channels are not enabled, the 6GHz band
is not scanned. Thus, if there are no APs on the 2GHz and 5GHz bands
(that will allow discovery of geographic location etc. that would
allow enabling the 6GHz channels) but there are non collocated APs
on 6GHz PSC channels these would never be discovered.
To overcome this, FW added support for performing passive UHB scan
in case no APs were discovered during scan on the 2GHz and 5GHz
channels.
Add support for enabling such scan when the following conditions are
met:
- 6GHz channels are supported but not enabled by regulatory.
- Station interface is not associated or less than a defined time
interval passed from the last resume or HW reset flows.
- At least 4 channels are included in the scan request
- The scan request includes the widlcard SSID.
- At least 50 minutes passed from the last 6GHz passive scan.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.7c7bd00e0aeb.Ib226ad57e416b43a710c36a78a617d4243458b99@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwlwifi patches intended for v5.12
* Check FW notification sizes for robustness;
* Improvements in the NAPI implementation;
* Implement a workaround for CCA-EXT;
* Add new FW API support;
* Fix a CSA bug;
* Implement PHY integration version parsing;
* A bit of refactoring;
* One more CSA bug fix, this time in the AP side;
* Support for new So devices and a bit of reorg;
* Per Platform Antenna Gain (PPAG) fixes and improvements;
* Improvements in the debug framework;
* Some other clean-ups and small fixes.
# gpg: Signature made Fri 05 Feb 2021 12:04:21 PM EET using RSA key ID 1A3CC5FA
# gpg: Good signature from "Luciano Roth Coelho (Luca) <luca@coelho.fi>"
# gpg: aka "Luciano Roth Coelho (Intel) <luciano.coelho@intel.com>"
drivers/net/can/dev.c
b552766c87 ("can: dev: prevent potential information leak in can_fill_info()")
3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
0a042c6ec9 ("can: dev: move netlink related code into seperate file")
Code move.
drivers/net/ethernet/mellanox/mlx5/core/en_ethtool.c
57ac4a31c4 ("net/mlx5e: Correctly handle changing the number of queues when the interface is down")
214baf2287 ("net/mlx5e: Support HTB offload")
Adjacent code changes
net/switchdev/switchdev.c
20776b465c ("net: switchdev: don't set port_obj_info->handled true when -EOPNOTSUPP")
ffb68fc58e ("net: switchdev: remove the transaction structure from port object notifiers")
bae33f2b5a ("net: switchdev: remove the transaction structure from port attributes")
Transaction parameter gets dropped otherwise keep the fix.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, _everything_ in cfg80211 holds the RTNL, and if you
have a slow USB device (or a few) you can get some bad lock
contention on that.
Fix that by re-adding a mutex to each wiphy/rdev as we had at
some point, so we have locking for the wireless_dev lists and
all the other things in there, and also so that drivers still
don't have to worry too much about it (they still won't get
parallel calls for a single device).
Then, we can restrict the RTNL to a few cases where we add or
remove interfaces and really need the added protection. Some
of the global list management still also uses the RTNL, since
we need to have it anyway for netdev management, but we only
hold the RTNL for very short periods of time here.
Link: https://lore.kernel.org/r/20210122161942.81df9f5e047a.I4a8e1a60b18863ea8c5e6d3a0faeafb2d45b2f40@changeid
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> [marvell driver issues]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we get a channel switch with a very long quiet period, we schedule
a work to disconnect after a while. This work runs in background. In the
meanwhile, we keep getting beacons and sending FW modify command for each.
This has a potential race, where we modify the CSA after we aborted it.
Protect the flow by setting csa_failed to true in case we abort, and check
it before sending the modify command.
This required a modification to the way we treat csa_failed in
iwl_mvm_post_channel_switch:
1. The variable isn't being reset anymore, so we can still look at it in
iwl_mvm_channel_switch_rx_beacon. This is fine, since we reset it when
starting a new CSA.
2. There is no more early return in case of csa_failed. This is fine,
since before this patch csa_failed was set only for GO, and for GO the
function is only resetting the power settings, which we want to restore
even in case of failure.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.b023856bdf39.I4ed0149e0018fe5e1ae3c2a1cbc614954016063f@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The argument type to iwl_mvm_notify_rx_queue() is currently just
a u8 *, but that's misleading because we actually need the inner
data to be of type struct iwl_mvm_internal_rxq_notif, because we
interpret it when we get it back from the device (to check the
sync bool and possibly the cookie.)
Therefore, clear up any potential confusion and require that the
data passed is of type struct iwl_mvm_internal_rxq_notif *.
Also, while at it, rename the "count" to "notif_size" as "count"
doesn't really clearly say what it's counting.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.d28e14682bdc.I9ac366aa97db045be4daa4ba263267a3ac6a6a2f@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
