[ Upstream commit 6f07342903 ]
The following error occurs when trying to restore a previously saved
ALSA mixer state (tested on a Rock 5B board):
$ alsactl --no-ucm -f /tmp/asound.state store hw:Analog
$ alsactl --no-ucm -I -f /tmp/asound.state restore hw:Analog
alsactl: set_control:1475: Cannot write control '2:0:0:ALC Capture Target Volume:0' : Invalid argument
According to ES8316 datasheet, the register at address 0x2B, which is
related to the above mixer control, contains by default the value 0xB0.
Considering the corresponding ALC target bits (ALCLVL) are 7:4, the
control is initialized with 11, which is one step above the maximum
value allowed by the driver:
ALCLVL | dB gain
-------+--------
0000 | -16.5
0001 | -15.0
0010 | -13.5
.... | .....
0111 | -6.0
1000 | -4.5
1001 | -3.0
1010 | -1.5
.... | .....
1111 | -1.5
The tests performed using the VU meter feature (--vumeter=TYPE) of
arecord/aplay confirm the specs are correct and there is no measured
gain if the 1011-1111 range would have been mapped to 0 dB:
dB gain | VU meter %
--------+-----------
-6.0 | 30-31
-4.5 | 35-36
-3.0 | 42-43
-1.5 | 50-51
0.0 | 50-51
Increment the max value allowed for ALC Capture Target Volume control,
so that it matches the hardware default. Additionally, update the
related TLV to prevent an artificial extension of the dB gain range.
Fixes: b8b88b7087 ("ASoC: add es8316 codec driver")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Link: https://lore.kernel.org/r/20230530181140.483936-2-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0cf765e598 ]
Fix the following error in kernel log due to too long sound card name:
"
asoc-audio-graph-card sound: ASoC: driver name too long 'STM32MP1-AV96-HDMI' -> 'STM32MP1-AV96-H'
"
Fixes: e027da3427 ("ARM: dts: stm32: Add bindings for audio on AV96")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 861bc1d288 ]
omap2 contains a hack to define tick_broadcast() on non-SMP
configurations in place of the normal SMP definition. This one
causes a warning because of a missing prototype:
arch/arm/mach-omap2/board-generic.c:44:6: error: no previous prototype for 'tick_broadcast'
Make sure to always include the header with the declaration.
Fixes: d86ad463d6 ("ARM: OMAP2+: Fix regression for using local timer on non-SMP SoCs")
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Link: https://lore.kernel.org/r/20230516153109.514251-9-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 419013740e ]
ep93xx_clocksource_read() is only called from the file it is declared in,
while ep93xx_timer_init() is declared in a header that is not included here.
arch/arm/mach-ep93xx/timer-ep93xx.c:120:13: error: no previous prototype for 'ep93xx_timer_init'
arch/arm/mach-ep93xx/timer-ep93xx.c:63:5: error: no previous prototype for 'ep93xx_clocksource_read'
Fixes: 000bc17817 ("ARM: ep93xx: switch to GENERIC_CLOCKEVENTS")
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20230516153109.514251-3-arnd@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f24b495508 ]
The previous setting was related to the overall dimension and not to the
active display area.
In the "PHYSICAL SPECIFICATIONS" section, the datasheet shows the
following parameters:
----------------------------------------------------------
| Item | Specifications | unit |
----------------------------------------------------------
| Display area | 98.7 (W) x 57.5 (H) | mm |
----------------------------------------------------------
| Overall dimension | 105.5(W) x 67.2(H) x 4.96(D) | mm |
----------------------------------------------------------
Fixes: 966fea78ad ("drm/panel: simple: Add support for Ampire AM-480272H3TMQW-T01H")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
[narmstrong: fixed Fixes commit id length]
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230516085039.3797303-1-dario.binacchi@amarulasolutions.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd9e329af7 ]
The datasheet describes the following initialization flow including
minimum delay times between each step:
1. DSI data lanes need to be in LP-11 and the clock lane in HS mode
2. toggle EN signal
3. initialize registers
4. enable PLL
5. soft reset
6. enable DSI stream
7. check error status register
To meet this requirement we need to make sure the host bridge's
pre_enable() is called first by using the pre_enable_prev_first
flag.
Furthermore we need to split enable() into pre_enable() which covers
steps 2-5 from above and enable() which covers step 7 and is called
after the host bridge's enable().
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Fixes: ceb515ba29 ("drm/bridge: ti-sn65dsi83: Add TI SN65DSI83 and SN65DSI84 driver")
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> #TQMa8MxML/MBa8Mx
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230503163313.2640898-3-frieder@fris.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5500f823db ]
The 96Boards specification expects a 1.8V power rail on the low-speed
expansion connector that is able to provide at least 0.18W / 100 mA.
According to the DB410c hardware user manual this is done by connecting
both L15 and L16 in parallel with up to 55mA each (for 110 mA total) [1].
Unfortunately the current regulator setup in the DB410c device tree
does not implement the specification correctly and only provides 5 mA:
- Only L15 is marked always-on, so L16 is never enabled.
- Without specifying a load the regulator is put into LPM where
it can only provide 5 mA.
Fix this by:
- Adding proper voltage constraints for L16.
- Making L16 always-on.
- Adding regulator-system-load for both L15 and L16. 100 mA should be
available in total, so specify 50 mA for each. (The regulator
hardware can only be in normal (55 mA) or low-power mode (5 mA) so
this will actually result in the expected 110 mA total...)
[1]: https://www.96boards.org/documentation/consumer/dragonboard/dragonboard410c/hardware-docs/hardware-user-manual.md.html#power-supplies
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 828dd5d66f ("arm64: dts: apq8016-sbc: make 1.8v available on LS expansion")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-2-54d4960a05fc@gerhold.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e27654df20 ]
For some reason DB410c has completely bogus regulator constraints that
actually just correspond to the programmable voltages which are already
provided by the regulator driver. Some of them are not just outside the
recommended operating conditions of the APQ8016E SoC but even exceed
the absolute maximum ratings, potentially risking permanent device
damage.
In practice it's not quite as dangerous thanks to the RPM firmware:
It turns out that it has its own voltage constraints and silently
clamps all regulator requests. For example, requesting 3.3V for L5
(allowed by the current regulator constraints!) still results in 1.8V
being programmed in the actual regulator hardware.
Experimentation with various voltages shows that the internal RPM
voltage constraints roughly correspond to the safe "specified range"
in the PM8916 Device Specification (rather than the "programmable
range" used inside apq8016-sbc.dtsi right now).
Combine those together with some fixed voltages used in the old
msm-3.10 device tree from Qualcomm to give DB410c some actually valid
voltage constraints.
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Fixes: 4c7d53d16d ("arm64: dts: apq8016-sbc: add regulators support")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230510-msm8916-regulators-v1-1-54d4960a05fc@gerhold.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e47a807843 ]
Add a family compatible for QCE IP on SM8550 SoC, which is equal to QCE IP
found on SM8150 SoC and described in the recently updated device tree
bindings documentation, as well add a generic QCE IP family compatible.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Stable-dep-of: 3cbf49ef16 ("arm64: dts: qcom: sm8550: correct crypto unit address")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3244442406 ]
On MSM8916 the wireless connectivity functionality (WiFi/Bluetooth) is
split into the digital part inside the SoC and the analog RF part inside
a supplementary WCN36xx chip. For MSM8916, three different options
exist:
- WCN3620 (WLAN 802.11 b/g/n 2.4 GHz + Bluetooth)
- WCN3660B (WLAN 802.11 a/b/g/n 2.4/5 GHz + Bluetooth)
- WCN3680B (WLAN 802.11ac 2.4/5 GHz + Bluetooth)
Choosing one of these is up to the board vendor. This means that the
compatible belongs into the board-specific DT part so people porting
new boards pay attention to set the correct compatible.
Right now msm8916.dtsi sets "qcom,wcn3620" as default compatible,
which does not work at all for boards that have WCN3660B or WCN3680B.
Remove the default compatible from msm8196.dtsi and move it to the board
DT as follows:
- Boards with only &pronto { status = "okay"; } used the default
"qcom,wcn3620" so far. They now set this explicitly for &wcnss_iris.
- Boards with &pronto { ... iris { compatible = "qcom,wcn3660b"; }};
already had an override that just moves to &wcnss_iris now.
- For msm8916-samsung-a2015-common.dtsi the WCN compatible differs for
boards making use of it (a3u: wcn3620, a5u: wcn3660b, e2015: wcn3620)
so the definitions move to the board-specific DT part.
Since this requires touching all the board DTs, use this as a chance to
name the WCNSS-related labels consistently, so everything is grouped
properly when sorted alphabetically.
No functional change, just clean-up for more clarity & easier porting.
Aside from ordering the generated DTBs are identical.
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230309091452.1011776-1-stephan.gerhold@kernkonzept.com
Stable-dep-of: 1f9a41bb0b ("arm64: dts: qcom: msm8916: correct WCNSS unit address")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c32c81f3db ]
Aaro reports problems on the OSK1 board after we altered
the dynamic base for GPIO allocations.
It appears this happens because the OMAP driver now
allocates GPIO numbers dynamically, so all that is
references by number is a bit up in the air.
Let's bite the bullet and try to just move the gpio_chip
in the tps65010 MFD driver over to using dynamic allocations.
Alter everything in the OSK1 board file to use a GPIO
descriptor table and lookups.
Utilize the NULL device to define some board-specific
GPIO lookups and use these to immediately look up the
same GPIOs, convert to IRQ numbers and pass as resources
to the devices. This is ugly but should work.
The .setup() callback for tps65010 was used for some GPIO
hogging, but since the OSK1 is the only user in the entire
kernel we can alter the signatures to something that
is helpful and make a clean transition.
Fixes: 92bf78b33b ("gpio: omap: use dynamic allocation of base")
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: andy.shevchenko@gmail.com
Cc: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Lee Jones <lee@kernel.org>
Reviewed-by: Lee Jones <lee@kernel.org>
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1464e48d69 ]
During probe, the driver registers i2c dummy devices and populates the
aux bus, which registers a device for the panel. After doing that, the
driver can still defer probe if needed. This ordering of operations is
troublesome however, because the deferred probe work will retry probing
all pending devices every time a new device is registered. Therefore, if
modules need to be loaded in order to satisfy the dependencies for this
driver to complete probe, the kernel will stall, since it'll keep trying
to probe the anx7625 driver, but never succeed, given that modules would
only be loaded after the deferred probe work completes.
Two changes are required to avoid this issue:
* Move of_find_mipi_dsi_host_by_node(), which can defer probe, to before
anx7625_register_i2c_dummy_clients() and
devm_of_dp_aux_populate_ep_devices(), which register devices.
* Make use of the done_probing callback when populating the aux bus,
so that the bridge registration is only done after the panel is
probed. This is required because the panel might need to defer probe,
but the aux bus population needs the i2c dummy devices working, so
this call couldn't just be moved to an earlier point in probe.
One caveat is that if the panel is described outside the aux bus, the
probe loop issue can still happen, but we don't have a way to avoid
it in that case since there's no callback available.
With this patch applied, it's possible to boot on
mt8192-asurada-spherion with
CONFIG_DRM_ANALOGIX_ANX7625=y
CONFIG_MTK_MMSYS=m
CONFIG_BACKLIGHT_PWM=y
and also with
CONFIG_DRM_ANALOGIX_ANX7625=y
CONFIG_MTK_MMSYS=y
CONFIG_BACKLIGHT_PWM=m
Fixes: adca62ec37 ("drm/bridge: anx7625: Support reading edid through aux channel")
Fixes: 269332997a ("drm/bridge: anx7625: Return -EPROBE_DEFER if the dsi host was not found")
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230518193902.891121-1-nfraprado@collabora.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4ffec92e70 ]
The model property should be at the top level, let's move it out
of the pinctrl node.
Fixes: d2eaf949d2 ("ARM: dts: omap3-gta04a5one: define GTA04A5 variant with OneNAND")
Cc: Andreas Kemnade <andreas@kemnade.info>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7061b6af34 ]
When map() is called on a detached domain, the domain does not exist in
the device so we do not send a MAP request, but we do update the
internal mapping tree, to be replayed on the next attach. Since this
constitutes a successful iommu_map() call, return *mapped in this case
too.
Fixes: 7e62edd7a3 ("iommu/virtio: Add map/unmap_pages() callbacks implementation")
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20230515113946.1017624-3-jean-philippe@linaro.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ff2e4bfd16 ]
bnxt_re currently uses the names "bnxt_qplib_creq" and "bnxt_qplib_nq-0"
while registering IRQs. There is no way to distinguish the IRQs of
different device ports when there are multiple IB devices registered.
This could make the scenarios worse where one want to pin IRQs of a device
port to certain CPUs.
Fixed the code to use unique names which has PCI BDF information while
registering interrupts like: "bnxt_re-nq-0@pci:0000:65:00.0" and
"bnxt_re-creq@pci:0000:65:00.1".
Fixes: 1ac5a40479 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Link: https://lore.kernel.org/r/1684478897-12247-4-git-send-email-selvin.xavier@broadcom.com
Reviewed-by: Bhargava Chenna Marreddy <bhargava.marreddy@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab112ee789 ]
When the ulp hook to start the IRQ fails because the rings are not
available, tasklets are not enabled. In this case when the driver is
unloaded, driver calls CREQ tasklet_kill. This causes an indefinite hang
as the tasklet is not enabled.
Driver shouldn't call tasklet_kill if it is not enabled. So using the
creq->requested and nq->requested flags to identify if both tasklets/irqs
are registered. Checking this flag while scheduling the tasklet from
ISR. Also, added a cleanup for disabling tasklet, in case request_irq
fails during start_irq.
Check for return value for bnxt_qplib_rcfw_start_irq and in case the
bnxt_qplib_rcfw_start_irq fails, return bnxt_re_start_irq without
attempting to start NQ IRQs.
Fixes: 1ac5a40479 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Link: https://lore.kernel.org/r/1684478897-12247-2-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0babf89c9c ]
In the unlikely event that something goes wrong with the device and
its registers, the fan_from_reg() function may return 0. This value
will cause a division-by-zero error in the show_pwm() function.
To prevent this, test the value of
fan_from_reg(data->fan_full_speed[nr]) against 0 before performing
the division. If the division-by-zero error is avoided, assign 0 to
the val variable.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: df9ec2dae0 ("hwmon: (f71882fg) Reorder symbols to get rid of a few forward declarations")
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Link: https://lore.kernel.org/r/20230510143537.145060-1-n.zhandarovich@fintech.ru
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
