Add the bare minimum needed to boot BCM2708 from a Device Tree.
Signed-off-by: Noralf Tronnes <notro@tronnes.org>
BCM2708: DT: change 'axi' nodename to 'soc'
Change DT node named 'axi' to 'soc' so it matches ARCH_BCM2835.
The VC4 bootloader fills in certain properties in the 'axi' subtree,
but since this is part of an upstreaming effort, the name is changed.
Signed-off-by: Noralf Tronnes notro@tronnes.org
BCM2708_DT: Correct length of the peripheral space
Use dts-dirs feature for overlays.
The kernel makefiles have a dts-dirs target that is for vendor subdirectories.
Using this fixes the install_dtbs target, which previously did not install the overlays.
BCM270X_DT: configure I2S DMA channels
Signed-off-by: Matthias Reichl <hias@horus.com>
BCM270X_DT: switch to bcm2835-i2s
I2S soundcard drivers with proper devicetree support (i.e. not linking
to the cpu_dai/platform via name but to cpu/platform via of_node)
will work out of the box without any modifications.
When the kernel is compiled without devicetree support the platform
code will instantiate the bcm2708-i2s driver and I2S soundcard drivers
will link to it via name, as before.
Signed-off-by: Matthias Reichl <hias@horus.com>
SDIO-overlay: add poll_once-boolean parameter
Add paramter to toggle sdio-device-polling
done every second or once at boot-time.
Signed-off-by: Patrick Boettcher <patrick.boettcher@posteo.de>
BCM270X_DT: Make mmc overlay compatible with current firmware
The original DT overlay logic followed a merge-then-patch procedure,
i.e. parameters are applied to the loaded overlay before the overlay
is merged into the base DTB. This sequence has been changed to
patch-then-merge, in order to support parameterised node names, and
to protect against bad overlays. As a result, overrides (parameters)
must only target labels in the overlay, but the overlay can obviously target nodes in the base DTB.
mmc-overlay.dts (that switches back to the original mmc sdcard
driver) is the only overlay violating that rule, and this patch
fixes it.
bcm270x_dt: Use the sdhost MMC controller by default
The "mmc" overlay reverts to using the other controller.
squash: Add cprman to dt
BCM270X_DT: Use clk_core for I2C interfaces
BCM270X_DT: Use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi
The mainline Device Tree files are quite close to downstream now.
Let's use bcm283x.dtsi, bcm2835.dtsi and bcm2836.dtsi as base files
for our dts files.
Mainline dts files are based on these files:
bcm2835-rpi.dtsi
bcm2835.dtsi bcm2836.dtsi
bcm283x.dtsi
Current downstream are based on these:
bcm2708.dtsi bcm2709.dtsi bcm2710.dtsi
bcm2708_common.dtsi
This patch introduces this dependency:
bcm2708.dtsi bcm2709.dtsi
bcm2708-rpi.dtsi
bcm270x.dtsi
bcm2835.dtsi bcm2836.dtsi
bcm283x.dtsi
And:
bcm2710.dtsi
bcm2708-rpi.dtsi
bcm270x.dtsi
bcm283x.dtsi
bcm270x.dtsi contains the downstream bcm283x.dtsi diff.
bcm2708-rpi.dtsi is the downstream version of bcm2835-rpi.dtsi.
Other changes:
- The led node has moved from /soc/leds to /leds. This is not a problem
since the label is used to reference it.
- The clk_osc reg property changes from 6 to 3.
- The gpu nodes has their interrupt property set in the base file.
- the clocks label does not point to the /clocks node anymore, but
points to the cprman node. This is not a problem since the overlays
that use the clock node refer to it directly: target-path = "/clocks";
- some nodes now have 2 labels since mainline and downstream differs in
this respect: cprman/clocks, spi0/spi, gpu/vc4.
- some nodes doesn't have an explicit status = "okay" since they're not
disabled in the base file: watchdog and random.
- gpiomem doesn't need an explicit status = "okay".
- bcm2708-rpi-cm.dts got the hpd-gpios property from bcm2708_common.dtsi,
it's now set directly in that file.
- bcm2709-rpi-2-b.dts has the timer node moved from /soc/timer to /timer.
- Removed clock-frequency property on the bcm{2709,2710}.dtsi timer nodes.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270X_DT: Use raspberrypi-power to turn on USB power
Use the raspberrypi-power driver to turn on USB power.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
BCM270X_DT: Add a .dtbo target, use for overlays
Change the filenames and extensions to keep the pre-DDT style of
overlay (<name>-overlay.dtb) distinct from new ones that use a
different style of local fixups (<name>.dtbo), and to match other
platforms.
The RPi firmware uses the DDTK trailer atom to choose which type of
overlay to use for each kernel.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Don't generate "linux,phandle" props
The EPAPR standard says to use "phandle" properties to store phandles,
rather than the deprecated "linux,phandle" version. By default, dtc
generates both, but adding "-H epapr" causes it to only generate
"phandle"s, saving some space and clutter.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Add overlay for enc28j60 on SPI2
Works on SPI2 for compute module
BCM270X_DT: Add midi-uart0 overlay
MIDI requires 31.25kbaud, a baudrate unsupported by Linux. The
midi-uart0 overlay configures uart0 (ttyAMA0) to use a fake clock
so that requesting 38.4kbaud actually gets 31.25kbaud.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: Add i2c-sensor overlay
The i2c-sensor overlay is a container for various pressure and
temperature sensors, currently bmp085 and bmp280. The standalone
bmp085_i2c-sensor overlay is now deprecated.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
BCM270X_DT: overlays/*-overlay.dtb -> overlays/*.dtbo (#1752)
We now create overlays as .dtbo files.
build: support for .dtbo files for dtb overlays
Kernel 4.4.6+ on RaspberryPi support .dtbo files for overlays, instead of .dtb.
Patch the kernel, which has faulty rules to generate .dtbo the way yocto does
Signed-off-by: Herve Jourdain <herve.jourdain@neuf.fr>
Signed-off-by: Khem Raj <raj.khem@gmail.com>
BCM270X: Drop position requirement for CMA in VC4 overlay.
No longer necessary since 2aefcd5761,
and will probably let peeople that want to choose a larger CMA
allocation (particularly on pi0/1).
Signed-off-by: Eric Anholt <eric@anholt.net>
BCM270X_DT: RPi Device Tree tidy
Use the upstream sdhost node, add thermal-zones, and factor out some
common elements.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
kbuild: Silence unhelpful DTC warnings
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
The Raspberry Pi firmware looks for a trailer on the kernel image to
determine whether it was compiled with Device Tree support enabled.
If the firmware finds a kernel without this trailer, or which has a
trailer indicating that it isn't DT-capable, it disables DT support
and reverts to using ATAGs.
The mkknlimg utility adds that trailer, having first analysed the
image to look for signs of DT support and the kernel version string.
knlinfo displays the contents of the trailer in the given kernel image.
scripts/mkknlimg: Add support for ARCH_BCM2835
Add a new trailer field indicating whether this is an ARCH_BCM2835
build, as opposed to MACH_BCM2708/9. If the loader finds this flag
is set it changes the default base dtb file name from bcm270x...
to bcm283y...
Also update knlinfo to show the status of the field.
scripts/mkknlimg: Improve ARCH_BCM2835 detection
The board support code contains sufficient strings to be able to
distinguish 2708 vs. 2835 builds, so remove the check for
bcm2835-pm-wdt which could exist in either.
Also, since the canned configuration is no longer built in (it's
a module), remove the config string checking.
See: https://github.com/raspberrypi/linux/issues/1157
scripts: Multi-platform support for mkknlimg and knlinfo
The firmware uses tags in the kernel trailer to choose which dtb file
to load. Current firmware loads bcm2835-*.dtb if the '283x' tag is true,
otherwise it loads bcm270*.dtb. This scheme breaks if an image supports
multiple platforms.
This patch adds '270X' and '283X' tags to indicate support for RPi and
upstream platforms, respectively. '283x' (note lower case 'x') is left
for old firmware, and is only set if the image only supports upstream
builds.
scripts/mkknlimg: Append a trailer for all input
Now that the firmware assumes an unsigned kernel is DT-capable, it is
helpful to be able to mark a kernel as being non-DT-capable.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
scripts/knlinfo: Decode DDTK atom
Show the DDTK atom as being a boolean.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
mkknlimg: Retain downstream-kernel detection
With the death of ARCH_BCM2708 and ARCH_BCM2709, a new way is needed to
determine if this is a "downstream" build that wants the firmware to
load a bcm27xx .dtb. The vc_cma driver is used downstream but not
upstream, making vc_cma_init a suitable predicate symbol.
mkknlimg: Find some more downstream-only strings
See: https://github.com/raspberrypi/linux/issues/1920
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
scripts: Update mkknlimg, just in case
With the removal of the vc_cma driver, mkknlimg lost an indication that
the user had built a downstream kernel. Update the script, adding a few
more key strings, in case it is still being used.
Note that mkknlimg is now deprecated, except to tag kernels as upstream
(283x), and thus requiring upstream DTBs.
See: https://github.com/raspberrypi/linux/issues/2239
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
[ Upstream commit 10dce8af34 ]
Commit 9c225f2655 ("vfs: atomic f_pos accesses as per POSIX") added
locking for file.f_pos access and in particular made concurrent read and
write not possible - now both those functions take f_pos lock for the
whole run, and so if e.g. a read is blocked waiting for data, write will
deadlock waiting for that read to complete.
This caused regression for stream-like files where previously read and
write could run simultaneously, but after that patch could not do so
anymore. See e.g. commit 581d21a2d0 ("xenbus: fix deadlock on writes
to /proc/xen/xenbus") which fixes such regression for particular case of
/proc/xen/xenbus.
The patch that added f_pos lock in 2014 did so to guarantee POSIX thread
safety for read/write/lseek and added the locking to file descriptors of
all regular files. In 2014 that thread-safety problem was not new as it
was already discussed earlier in 2006.
However even though 2006'th version of Linus's patch was adding f_pos
locking "only for files that are marked seekable with FMODE_LSEEK (thus
avoiding the stream-like objects like pipes and sockets)", the 2014
version - the one that actually made it into the tree as 9c225f2655 -
is doing so irregardless of whether a file is seekable or not.
See
https://lore.kernel.org/lkml/53022DB1.4070805@gmail.com/https://lwn.net/Articles/180387https://lwn.net/Articles/180396
for historic context.
The reason that it did so is, probably, that there are many files that
are marked non-seekable, but e.g. their read implementation actually
depends on knowing current position to correctly handle the read. Some
examples:
kernel/power/user.c snapshot_read
fs/debugfs/file.c u32_array_read
fs/fuse/control.c fuse_conn_waiting_read + ...
drivers/hwmon/asus_atk0110.c atk_debugfs_ggrp_read
arch/s390/hypfs/inode.c hypfs_read_iter
...
Despite that, many nonseekable_open users implement read and write with
pure stream semantics - they don't depend on passed ppos at all. And for
those cases where read could wait for something inside, it creates a
situation similar to xenbus - the write could be never made to go until
read is done, and read is waiting for some, potentially external, event,
for potentially unbounded time -> deadlock.
Besides xenbus, there are 14 such places in the kernel that I've found
with semantic patch (see below):
drivers/xen/evtchn.c:667:8-24: ERROR: evtchn_fops: .read() can deadlock .write()
drivers/isdn/capi/capi.c:963:8-24: ERROR: capi_fops: .read() can deadlock .write()
drivers/input/evdev.c:527:1-17: ERROR: evdev_fops: .read() can deadlock .write()
drivers/char/pcmcia/cm4000_cs.c:1685:7-23: ERROR: cm4000_fops: .read() can deadlock .write()
net/rfkill/core.c:1146:8-24: ERROR: rfkill_fops: .read() can deadlock .write()
drivers/s390/char/fs3270.c:488:1-17: ERROR: fs3270_fops: .read() can deadlock .write()
drivers/usb/misc/ldusb.c:310:1-17: ERROR: ld_usb_fops: .read() can deadlock .write()
drivers/hid/uhid.c:635:1-17: ERROR: uhid_fops: .read() can deadlock .write()
net/batman-adv/icmp_socket.c:80:1-17: ERROR: batadv_fops: .read() can deadlock .write()
drivers/media/rc/lirc_dev.c:198:1-17: ERROR: lirc_fops: .read() can deadlock .write()
drivers/leds/uleds.c:77:1-17: ERROR: uleds_fops: .read() can deadlock .write()
drivers/input/misc/uinput.c:400:1-17: ERROR: uinput_fops: .read() can deadlock .write()
drivers/infiniband/core/user_mad.c:985:7-23: ERROR: umad_fops: .read() can deadlock .write()
drivers/gnss/core.c:45:1-17: ERROR: gnss_fops: .read() can deadlock .write()
In addition to the cases above another regression caused by f_pos
locking is that now FUSE filesystems that implement open with
FOPEN_NONSEEKABLE flag, can no longer implement bidirectional
stream-like files - for the same reason as above e.g. read can deadlock
write locking on file.f_pos in the kernel.
FUSE's FOPEN_NONSEEKABLE was added in 2008 in a7c1b990f7 ("fuse:
implement nonseekable open") to support OSSPD. OSSPD implements /dev/dsp
in userspace with FOPEN_NONSEEKABLE flag, with corresponding read and
write routines not depending on current position at all, and with both
read and write being potentially blocking operations:
See
https://github.com/libfuse/osspdhttps://lwn.net/Articles/308445https://github.com/libfuse/osspd/blob/14a9cff0/osspd.c#L1406https://github.com/libfuse/osspd/blob/14a9cff0/osspd.c#L1438-L1477https://github.com/libfuse/osspd/blob/14a9cff0/osspd.c#L1479-L1510
Corresponding libfuse example/test also describes FOPEN_NONSEEKABLE as
"somewhat pipe-like files ..." with read handler not using offset.
However that test implements only read without write and cannot exercise
the deadlock scenario:
https://github.com/libfuse/libfuse/blob/fuse-3.4.2-3-ga1bff7d/example/poll.c#L124-L131https://github.com/libfuse/libfuse/blob/fuse-3.4.2-3-ga1bff7d/example/poll.c#L146-L163https://github.com/libfuse/libfuse/blob/fuse-3.4.2-3-ga1bff7d/example/poll.c#L209-L216
I've actually hit the read vs write deadlock for real while implementing
my FUSE filesystem where there is /head/watch file, for which open
creates separate bidirectional socket-like stream in between filesystem
and its user with both read and write being later performed
simultaneously. And there it is semantically not easy to split the
stream into two separate read-only and write-only channels:
https://lab.nexedi.com/kirr/wendelin.core/blob/f13aa600/wcfs/wcfs.go#L88-169
Let's fix this regression. The plan is:
1. We can't change nonseekable_open to include &~FMODE_ATOMIC_POS -
doing so would break many in-kernel nonseekable_open users which
actually use ppos in read/write handlers.
2. Add stream_open() to kernel to open stream-like non-seekable file
descriptors. Read and write on such file descriptors would never use
nor change ppos. And with that property on stream-like files read and
write will be running without taking f_pos lock - i.e. read and write
could be running simultaneously.
3. With semantic patch search and convert to stream_open all in-kernel
nonseekable_open users for which read and write actually do not
depend on ppos and where there is no other methods in file_operations
which assume @offset access.
4. Add FOPEN_STREAM to fs/fuse/ and open in-kernel file-descriptors via
steam_open if that bit is present in filesystem open reply.
It was tempting to change fs/fuse/ open handler to use stream_open
instead of nonseekable_open on just FOPEN_NONSEEKABLE flags, but
grepping through Debian codesearch shows users of FOPEN_NONSEEKABLE,
and in particular GVFS which actually uses offset in its read and
write handlers
https://codesearch.debian.net/search?q=-%3Enonseekable+%3Dhttps://gitlab.gnome.org/GNOME/gvfs/blob/1.40.0-6-gcbc54396/client/gvfsfusedaemon.c#L1080https://gitlab.gnome.org/GNOME/gvfs/blob/1.40.0-6-gcbc54396/client/gvfsfusedaemon.c#L1247-1346https://gitlab.gnome.org/GNOME/gvfs/blob/1.40.0-6-gcbc54396/client/gvfsfusedaemon.c#L1399-1481
so if we would do such a change it will break a real user.
5. Add stream_open and FOPEN_STREAM handling to stable kernels starting
from v3.14+ (the kernel where 9c225f2655 first appeared).
This will allow to patch OSSPD and other FUSE filesystems that
provide stream-like files to return FOPEN_STREAM | FOPEN_NONSEEKABLE
in their open handler and this way avoid the deadlock on all kernel
versions. This should work because fs/fuse/ ignores unknown open
flags returned from a filesystem and so passing FOPEN_STREAM to a
kernel that is not aware of this flag cannot hurt. In turn the kernel
that is not aware of FOPEN_STREAM will be < v3.14 where just
FOPEN_NONSEEKABLE is sufficient to implement streams without read vs
write deadlock.
This patch adds stream_open, converts /proc/xen/xenbus to it and adds
semantic patch to automatically locate in-kernel places that are either
required to be converted due to read vs write deadlock, or that are just
safe to be converted because read and write do not use ppos and there
are no other funky methods in file_operations.
Regarding semantic patch I've verified each generated change manually -
that it is correct to convert - and each other nonseekable_open instance
left - that it is either not correct to convert there, or that it is not
converted due to current stream_open.cocci limitations.
The script also does not convert files that should be valid to convert,
but that currently have .llseek = noop_llseek or generic_file_llseek for
unknown reason despite file being opened with nonseekable_open (e.g.
drivers/input/mousedev.c)
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Yongzhi Pan <panyongzhi@gmail.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Tejun Heo <tj@kernel.org>
Cc: Kirill Tkhai <ktkhai@virtuozzo.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Nikolaus Rath <Nikolaus@rath.org>
Cc: Han-Wen Nienhuys <hanwen@google.com>
Signed-off-by: Kirill Smelkov <kirr@nexedi.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9c38f1f044 ]
Backspace is not working on some terminal emulators which do not send the
key code defined by terminfo. Terminals either send '^H' (8) or '^?' (127).
But currently only '^?' is handled. Let's also handle '^H' for those
terminals.
Signed-off-by: Changbin Du <changbin.du@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin (Microsoft) <sashal@kernel.org>
commit dfbd199a7c upstream.
When compiling genheaders and mdp from a newer host kernel, the
following error happens:
In file included from scripts/selinux/genheaders/genheaders.c:18:
./security/selinux/include/classmap.h:238:2: error: #error New
address family defined, please update secclass_map. #error New
address family defined, please update secclass_map. ^~~~~
make[3]: *** [scripts/Makefile.host:107:
scripts/selinux/genheaders/genheaders] Error 1 make[2]: ***
[scripts/Makefile.build:599: scripts/selinux/genheaders] Error 2
make[1]: *** [scripts/Makefile.build:599: scripts/selinux] Error 2
make[1]: *** Waiting for unfinished jobs....
Instead of relying on the host definition, include linux/socket.h in
classmap.h to have PF_MAX.
Cc: stable@vger.kernel.org
Signed-off-by: Paulo Alcantara <paulo@paulo.ac>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
[PM: manually merge in mdp.c, subject line tweaks]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f880eea68f ]
Use specific prototype instead of an opaque pointer so that the
compiler can catch function prototype mismatch.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec91e78d37 ]
Commit e49ce14150 ("modpost: use linker section to generate table.")
was not so cool as we had expected first; it ended up with ugly section
hacks when commit dd2a3acaec ("mod/file2alias: make modpost compile
on darwin again") came in.
Given a certain degree of unknowledge about the link stage of host
programs, I really want to see simple, stupid table lookup so that
this works in the same way regardless of the underlying executable
format.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02826a6ba3 ]
Ard Biesheuvel reports bindeb-pkg with O= option is broken in the
following way:
...
LD [M] sound/soc/rockchip/snd-soc-rk3399-gru-sound.ko
LD [M] sound/soc/rockchip/snd-soc-rockchip-pcm.ko
LD [M] sound/soc/rockchip/snd-soc-rockchip-rt5645.ko
LD [M] sound/soc/rockchip/snd-soc-rockchip-spdif.ko
LD [M] sound/soc/sh/rcar/snd-soc-rcar.ko
fakeroot -u debian/rules binary
make KERNELRELEASE=4.19.0-12677-g19beffaf7a99-dirty ARCH=arm64 KBUILD_SRC= intdeb-pkg
/bin/bash /home/ard/linux/scripts/package/builddeb
Makefile:600: include/config/auto.conf: No such file or directory
***
*** Configuration file ".config" not found!
***
*** Please run some configurator (e.g. "make oldconfig" or
*** "make menuconfig" or "make xconfig").
***
make[12]: *** [syncconfig] Error 1
make[11]: *** [syncconfig] Error 2
make[10]: *** [include/config/auto.conf] Error 2
make[9]: *** [__sub-make] Error 2
...
Prior to commit 80463f1b7b ("kbuild: add --include-dir flag only
for out-of-tree build"), both srctree and objtree were added to
--include-dir redundantly, and the wrong code '$MAKE image_name'
was working by relying on that. Now, the potential issue that had
previously been hidden just showed up.
'$MAKE image_name' recurses to the generated $(objtree)/Makefile and
ends up with running in srctree, which is incorrect. It should be
invoked with '-f $srctree/Makefile' (or KBUILD_SRC=) to be executed
in objtree.
Fixes: 80463f1b7b ("kbuild: add --include-dir flag only for out-of-tree build")
Reported-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 54a7151b14 upstream.
Fix commit 56067812d5 ("kbuild: modversions: add infrastructure for
emitting relative CRCs") where CRCs are interpreted in host byte order
rather than proper kernel byte order. The bug is conditional on
CONFIG_MODULE_REL_CRCS.
For example, when loading a BE module into a BE kernel compiled with a LE
system, the error "disagrees about version of symbol module_layout" is
produced. A message such as "Found checksum D7FA6856 vs module 5668FAD7"
will be given with debug enabled, which indicates an obvious endian
problem within __kcrctab within the kernel image.
The general solution is to use the macro TO_NATIVE, as is done in
similar cases throughout modpost.c. With this correction it has been
verified that a BE kernel compiled with a LE system accepts BE modules.
This change has also been verified with a LE kernel compiled with a LE
system, in which case TO_NATIVE returns its value unmodified since the
byte orders match. This is by far the common case.
Fixes: 56067812d5 ("kbuild: modversions: add infrastructure for emitting relative CRCs")
Signed-off-by: Fredrik Noring <noring@nocrew.org>
Cc: stable@vger.kernel.org
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5818c683a6 ]
If an ARM mapping symbol shares an address with a valid symbol,
find_elf_symbol can currently return the mapping symbol instead, as the
symbol is not validated. This can result in confusing warnings:
WARNING: vmlinux.o(.text+0x18f4028): Section mismatch in reference
from the function set_reset_devices() to the variable .init.text:$x.0
This change adds a call to is_valid_name to find_elf_symbol, similarly
to how it's already used in find_elf_symbol2.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fbac5977d8 ]
An unterminated string literal followed by new line is passed to the
parser (with "multi-line strings not supported" warning shown), then
handled properly there.
On the other hand, an unterminated string literal at end of file is
never passed to the parser, then results in memory leak.
[Test Code]
----------(Kconfig begin)----------
source "Kconfig.inc"
config A
bool "a"
-----------(Kconfig end)-----------
--------(Kconfig.inc begin)--------
config B
bool "b\No new line at end of file
---------(Kconfig.inc end)---------
[Summary from Valgrind]
Before the fix:
LEAK SUMMARY:
definitely lost: 16 bytes in 1 blocks
...
After the fix:
LEAK SUMMARY:
definitely lost: 0 bytes in 0 blocks
...
Eliminate the memory leak path by handling this case. Of course, such
a Kconfig file is wrong already, so I will add an error message later.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77c1c0fa8b ]
Currently, warn_ignore_character() displays invalid file name and
line number.
The lexer should use current_file->name and yylineno, while the parser
should use zconf_curname() and zconf_lineno().
This difference comes from that the lexer is always going ahead
of the parser. The parser needs to look ahead one token to make a
shift/reduce decision, so the lexer is requested to scan more text
from the input file.
This commit fixes the warning message from warn_ignored_character().
[Test Code]
----(Kconfig begin)----
/
-----(Kconfig end)-----
[Output]
Before the fix:
<none>:0:warning: ignoring unsupported character '/'
After the fix:
Kconfig:1:warning: ignoring unsupported character '/'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f1733a1d3c ]
There is actually a space after "sp," like this,
ffff2000080813c8: a9bb7bfd stp x29, x30, [sp, #-80]!
Right now, checkstack.pl isn't able to print anything on aarch64,
because it won't be able to match the stating objdump line of a function
due to this missing space. Hence, it displays every stack as zero-size.
After this patch, checkpatch.pl is able to match the start of a
function's objdump, and is then able to calculate each function's stack
correctly.
Link: http://lkml.kernel.org/r/20181207195843.38528-1-cai@lca.pw
Signed-off-by: Qian Cai <cai@lca.pw>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 38c7b224ce upstream.
New versions of gcc reasonably warn about the odd pattern of
strncpy(p, q, strlen(q));
which really doesn't make sense: the strncpy() ends up being just a slow
and odd way to write memcpy() in this case.
There was a comment about _why_ the code used strncpy - to avoid the
terminating NUL byte, but memcpy does the same and avoids the warning.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8ef14c2c41 ]
This reverts commit 6147b1cf19.
The reverted patch results in attempted write access to the source
repository, even if that repository is mounted read-only.
Output from "strace git status -uno --porcelain":
getcwd("/tmp/linux-test", 129) = 16
open("/tmp/linux-test/.git/index.lock", O_RDWR|O_CREAT|O_EXCL|O_CLOEXEC, 0666) =
-1 EROFS (Read-only file system)
While git appears to be able to handle this situation, a monitored
build environment (such as the one used for Chrome OS kernel builds)
may detect it and bail out with an access violation error. On top of
that, the attempted write access suggests that git _will_ write to the
file even if a build output directory is specified. Users may have the
reasonable expectation that the source repository remains untouched in
that situation.
Fixes: 6147b1cf19 ("scripts/setlocalversion: git: Make -dirty check more robust"
Cc: Genki Sky <sky@genki.is>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbcde0a724 ]
Since commit b41d920acf ("kbuild: deb-pkg: split generating packaging
and build"), the build version of the kernel contained in a deb package
is too low by 1.
Prior to the bad commit, the kernel was built first, then the number
in .version file was read out, and written into the debian control file.
Now, the debian control file is created before the kernel is actually
compiled, which is causing the version number mismatch.
Let the mkdebian script pass KBUILD_BUILD_VERSION=${revision} to require
the build system to use the specified version number.
Fixes: b41d920acf ("kbuild: deb-pkg: split generating packaging and build")
Reported-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6f4d29df66 upstream.
Without this change the following happens when using Python3 (3.6.6):
$ echo "GPL-2.0" | python3 scripts/spdxcheck.py -
FAIL: 'str' object has no attribute 'decode'
Traceback (most recent call last):
File "scripts/spdxcheck.py", line 253, in <module>
parser.parse_lines(sys.stdin, args.maxlines, '-')
File "scripts/spdxcheck.py", line 171, in parse_lines
line = line.decode(locale.getpreferredencoding(False), errors='ignore')
AttributeError: 'str' object has no attribute 'decode'
So as the line is already a string, there is no need to decode it and
the line can be dropped.
/usr/bin/python on Arch is Python 3. So this would indeed be worth
going into 4.19.
Link: http://lkml.kernel.org/r/20181023070802.22558-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Joe Perches <joe@perches.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Masahiro writes:
"Kbuild fixes for v4.19 (2nd)
- Fix warnings from recordmcount.pl when building with Clang
- Allow Clang to use GNU toolchains correctly
- Disable CONFIG_SAMPLES for UML to avoid build error"
* tag 'kbuild-fixes-v4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
samples: disable CONFIG_SAMPLES for UML
kbuild: allow to use GCC toolchain not in Clang search path
ftrace: Build with CPPFLAGS to get -Qunused-arguments
When building to record the mcount locations the kernel uses
KBUILD_CFLAGS but not KBUILD_CPPFLAGS. This means it lacks
-Qunused-arguments when building with clang, resulting in a lot of
noisy warnings.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Pulled kselftest fixes from Shuah:
"This Kselftest fixes update for 4.9-rc5 consists of:
-- fixes to build failures
-- fixes to add missing config files to increase test coverage
-- fixes to cgroup test and a new cgroup test for memory.oom.group"
Pull Kbuild fixes from Masahiro Yamada:
- make setlocalversion more robust about -dirty check
- loosen the pkg-config requirement for Kconfig
- change missing depmod to a warning from an error
- warn modules_install when System.map is missing
* tag 'kbuild-fixes-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: modules_install: warn when missing System.map file
kbuild: make missing $DEPMOD a Warning instead of an Error
kconfig: do not require pkg-config on make {menu,n}config
kconfig: remove a spurious self-assignment
scripts/setlocalversion: git: Make -dirty check more robust
If there is no System.map file for "make modules_install",
scripts/depmod.sh will silently exit with success, having done
nothing. Since this is an unexpected situation, change it to
report a Warning for the missing file. The behavior is not
changed except for the Warning message.
The (previous) silent success and new Warning can be reproduced
by:
$ make mrproper; make defconfig
$ make modules; make modules_install
and since System.map is produced by "make vmlinux", the steps
above omit producing the System.map file.
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Pull nds32 updates from Greentime Hu:
"Contained in here are the bug fixes, building error fixes and ftrace
support for nds32"
* tag 'nds32-for-linus-4.19-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/greentime/linux:
nds32: linker script: GCOV kernel may refers data in __exit
nds32: fix build error because of wrong semicolon
nds32: Fix a kernel panic issue because of wrong frame pointer access.
nds32: Only print one page of stack when die to prevent printing too much information.
nds32: Add macro definition for offset of lp register on stack
nds32: Remove the deprecated ABI implementation
nds32/stack: Get real return address by using ftrace_graph_ret_addr
nds32/ftrace: Support dynamic function graph tracer
nds32/ftrace: Support dynamic function tracer
nds32/ftrace: Add RECORD_MCOUNT support
nds32/ftrace: Support static function graph tracer
nds32/ftrace: Support static function tracer
nds32: Extract the checking and getting pointer to a macro
nds32: Clean up the coding style
nds32: Fix get_user/put_user macro expand pointer problem
nds32: Fix empty call trace
nds32: add NULL entry to the end of_device_id array
nds32: fix logic for module
If the kernel headers aren't installed we can't build all the tests.
Add a new make target rule 'khdr' in the file lib.mk to generate the
kernel headers and that gets include for every test-dir Makefile that
includes lib.mk If the testdir in turn have its own sub-dirs the
top_srcdir needs to be set to the linux-rootdir to be able to generate
the kernel headers.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Fathi Boudra <fathi.boudra@linaro.org>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
__ro_after_init is a specific __attribute__ that checkpatch does currently
not understand.
Add it to the known $Attribute types so that code that uses variables
declared with __ro_after_init are not thought to be a modifier type.
This appears as a defect in checkpatch output of code like:
static bool trust_cpu __ro_after_init = IS_ENABLED(CONFIG_RANDOM_TRUST_CPU);
[...]
if (trust_cpu && arch_init) {
where checkpatch reports:
ERROR: space prohibited after that '&&' (ctx:WxW)
if (trust_cpu && arch_init) {
Link: http://lkml.kernel.org/r/0fa8a2cb83ade4c525e18261ecf6cfede3015983.camel@perches.com
Signed-off-by: Joe Perches <joe@perches.com>
Reported-by: Kees Cook <keescook@chromium.org>
Tested-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When $DEPMOD is not found, only print a warning instead of exiting
with an error message and error status:
Warning: 'make modules_install' requires /sbin/depmod. Please install it.
This is probably in the kmod package.
Change the Error to a Warning because "not all build hosts for cross
compiling Linux are Linux systems and are able to provide a working
port of depmod, especially at the file patch /sbin/depmod."
I.e., "make modules_install" may be used to copy/install the
loadable modules files to a target directory on a build system and
then transferred to an embedded device where /sbin/depmod is run
instead of it being run on the build system.
Fixes: 934193a654 ("kbuild: verify that $DEPMOD is installed")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: stable@vger.kernel.org
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Lucas De Marchi <lucas.de.marchi@gmail.com>
Cc: Michal Marek <michal.lkml@markovi.net>
Cc: Jessica Yu <jeyu@kernel.org>
Cc: Chih-Wei Huang <cwhuang@linux.org.tw>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Meelis Roos reported a {menu,n}config regression:
"I have libncurses devel package installed in the default system
location (as do 99%+ on actual developers probably) and in this
case, pkg-config is useless. pkg-config is needed only when
libraries and headers are installed in non-default locations but
it is bad to require installation of pkg-config on all the machines
where make menuconfig would be possibly run."
For {menu,n}config, do not use pkg-config if it is not installed.
For {g,x}config, keep checking pkg-config since we really rely on it
for finding the installation paths of the required packages.
Fixes: 4ab3b80159 ("kconfig: check for pkg-config on make {menu,n,g,x}config")
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Meelis Roos <mroos@linux.ee>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Pull x86 fixes from Thomas Gleixner:
"Speculation:
- Make the microcode check more robust
- Make the L1TF memory limit depend on the internal cache physical
address space and not on the CPUID advertised physical address
space, which might be significantly smaller. This avoids disabling
L1TF on machines which utilize the full physical address space.
- Fix the GDT mapping for EFI calls on 32bit PTI
- Fix the MCE nospec implementation to prevent #GP
Fixes and robustness:
- Use the proper operand order for LSL in the VDSO
- Prevent NMI uaccess race against CR3 switching
- Add a lockdep check to verify that text_mutex is held in
text_poke() functions
- Repair the fallout of giving native_restore_fl() a prototype
- Prevent kernel memory dumps based on usermode RIP
- Wipe KASAN shadow stack before rewinding the stack to prevent false
positives
- Move the AMS GOTO enforcement to the actual build stage to allow
user API header extraction without a compiler
- Fix a section mismatch introduced by the on demand VDSO mapping
change
Miscellaneous:
- Trivial typo, GCC quirk removal and CC_SET/OUT() cleanups"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pti: Fix section mismatch warning/error
x86/vdso: Fix lsl operand order
x86/mce: Fix set_mce_nospec() to avoid #GP fault
x86/efi: Load fixmap GDT in efi_call_phys_epilog()
x86/nmi: Fix NMI uaccess race against CR3 switching
x86: Allow generating user-space headers without a compiler
x86/dumpstack: Don't dump kernel memory based on usermode RIP
x86/asm: Use CC_SET()/CC_OUT() in __gen_sigismember()
x86/alternatives: Lockdep-enforce text_mutex in text_poke*()
x86/entry/64: Wipe KASAN stack shadow before rewind_stack_do_exit()
x86/irqflags: Mark native_restore_fl extern inline
x86/build: Remove jump label quirk for GCC older than 4.5.2
x86/Kconfig: Fix trivial typo
x86/speculation/l1tf: Increase l1tf memory limit for Nehalem+
x86/spectre: Add missing family 6 check to microcode check
The self assignment was probably introduced by an automated code
refactoring in
commit 694c49a7c0 ("kconfig: drop localization support").
The issue was identified by a self-assign warning when running
make menuconfig with clang.
Fixes: 694c49a7c0 ("kconfig: drop localization support")
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
$(git diff-index) relies on the index being refreshed. This refreshing
of the index used to happen, but was removed in cdf2bc632e
("scripts/setlocalversion on write-protected source tree", 2013-06-14)
due to issues with a read-only filesystem.
If the index is not refreshed, one runs into problems. E.g. as
described in [0], git stores the uid in its index, so even if just the
uid has changed (or git is tricked into thinking so), then we will
think the tree is dirty. So as in [1], if you package linux-git with a
system that uses fakeroot(1), you get a "-dirty" version. Unless you
manually $(git update-index --refresh) themselves.
The simplest solution seems to be $(git status --porcelain), with an
additional flag saying "ignore untracked files". It seems clearer
about what it does, and avoids issues regarding cached indexes and
writable filesystems, but still has stable output for scripting.
[0]: https://public-inbox.org/git/0190ae30-b6c8-2a8b-b1fb-fd9d84e6dfdf@oracle.com/
[1]: https://bbs.archlinux.org/viewtopic.php?id=236702
Signed-off-by: Genki Sky <sky@genki.is>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Pull gcc plugin fix from Kees Cook:
"Lift gcc test into Kconfig. This is for better behavior when the
kernel is built with Clang, reported by Stefan Agner"
* tag 'gcc-plugins-v4.19-rc1-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
gcc-plugins: Disable when building under Clang
Pull more Kbuild updates from Masahiro Yamada:
- add build_{menu,n,g,x}config targets for compile-testing Kconfig
- fix and improve recursive dependency detection in Kconfig
- fix parallel building of menuconfig/nconfig
- fix syntax error in clang-version.sh
- suppress distracting log from syncconfig
- remove obsolete "rpm" target
- remove VMLINUX_SYMBOL(_STR) macro entirely
- fix microblaze build with CONFIG_DYNAMIC_FTRACE
- move compiler test for dead code/data elimination to Kconfig
- rename well-known LDFLAGS variable to KBUILD_LDFLAGS
- misc fixes and cleanups
* tag 'kbuild-v4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: rename LDFLAGS to KBUILD_LDFLAGS
kbuild: pass LDFLAGS to recordmcount.pl
kbuild: test dead code/data elimination support in Kconfig
initramfs: move gen_initramfs_list.sh from scripts/ to usr/
vmlinux.lds.h: remove stale <linux/export.h> include
export.h: remove VMLINUX_SYMBOL() and VMLINUX_SYMBOL_STR()
Coccinelle: remove pci_alloc_consistent semantic to detect in zalloc-simple.cocci
kbuild: make sorting initramfs contents independent of locale
kbuild: remove "rpm" target, which is alias of "rpm-pkg"
kbuild: Fix LOADLIBES rename in Documentation/kbuild/makefiles.txt
kconfig: suppress "configuration written to .config" for syncconfig
kconfig: fix "Can't open ..." in parallel build
kbuild: Add a space after `!` to prevent parsing as file pattern
scripts: modpost: check memory allocation results
kconfig: improve the recursive dependency report
kconfig: report recursive dependency involving 'imply'
kconfig: error out when seeing recursive dependency
kconfig: add build-only configurator targets
scripts/dtc: consolidate include path options in Makefile
Commit a0f97e06a4 ("kbuild: enable 'make CFLAGS=...' to add
additional options to CC") renamed CFLAGS to KBUILD_CFLAGS.
Commit 222d394d30 ("kbuild: enable 'make AFLAGS=...' to add
additional options to AS") renamed AFLAGS to KBUILD_AFLAGS.
Commit 06c5040cdb ("kbuild: enable 'make CPPFLAGS=...' to add
additional options to CPP") renamed CPPFLAGS to KBUILD_CPPFLAGS.
For some reason, LDFLAGS was not renamed.
Using a well-known variable like LDFLAGS may result in accidental
override of the variable.
Kbuild generally uses KBUILD_ prefixed variables for the internally
appended options, so here is one more conversion to sanitize the
naming convention.
I did not touch Makefiles under tools/ since the tools build system
is a different world.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Since commit 0fbe9a245c ("microblaze: add endianness options to
LDFLAGS instead of LD"), you cannot build the kernel for microblaze
with CONFIG_DYNAMIC_FTRACE.
Fixes: 0fbe9a245c ("microblaze: add endianness options to LDFLAGS instead of LD")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Prior to doing compiler feature detection in Kconfig, attempts to build
GCC plugins with Clang would fail the build, much in the same way missing
GCC plugin headers would fail the build. However, now that this logic
has been lifted into Kconfig, add an explicit test for GCC (instead of
duplicating it in the feature-test script).
Reported-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
