[ Upstream commit 65f8682b9a ]
For asic with VF MMIO access protection avoid using CPU for VM table updates.
CPU pagetable updates have issues with HDP flush as VF MMIO access protection
blocks write to mmBIF_BX_DEV0_EPF0_VF0_HDP_MEM_COHERENCY_FLUSH_CNTL register
during sriov runtime.
v3: introduce virtualization capability flag AMDGPU_VF_MMIO_ACCESS_PROTECT
which indicates that VF MMIO write access is not allowed in sriov runtime
Signed-off-by: Danijel Slivka <danijel.slivka@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 90bfee142a ]
If the number of pages from the userptr BO differs from the SG BO then the
allocated memory for the SG table doesn't get freed before returning
-EINVAL, which may lead to a memory leak in some error paths. Fix this by
checking the number of pages before allocating memory for the SG table.
Fixes: 264fb4d332 ("drm/amdgpu: Add multi-GPU DMA mapping helpers")
Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 62c52eac1a ]
DGFX platforms has lmem and cpu can access the lmem objects
via mmap and i915 internal i915_gem_object_pin_map() for
i915 own usages. Both of these methods has pre-requisite
requirement to keep GFX PCI endpoint in D0 for a supported
iomem transaction over PCI link. (Refer PCIe specs 5.3.1.4.1)
Both DG1/DG2 have a known hardware bug that violates the PCIe specs
and support the iomem read write transaction over PCIe bus despite
endpoint is D3 state.
Due to above H/W bug, we had never observed any issue with i915 runtime
PM versus lmem access.
But this issue becomes visible when PCIe gfx endpoint's upstream
bridge enters to D3, at this point any lmem read/write access will be
returned as unsupported request. But again this issue is not observed
on every platform because it has been observed on few host machines
DG1/DG2 endpoint's upstream bridge does not bind with pcieport driver.
which really disables the PCIe power savings and leaves the bridge
at D0 state.
We need a unique interface to read/write from lmem with runtime PM
wakeref protection something similar to intel_uncore_{read, write},
keep autosuspend control to 'on' on all discrete platforms,
until we have a unique interface to read/write from lmem.
This just change the default autosuspend setting of i915 on dGPU,
user can still change it to 'auto'.
v2:
- Modified the commit message and subject with more information.
- Changed the Fixes tag to LMEM support commit. [Joonas]
- Changed !HAS_LMEM() Cond to !IS_DGFX(). [Rodrigo]
Fixes: b908be543e ("drm/i915: support creating LMEM objects")
Suggested-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221014113258.1284226-1-anshuman.gupta@intel.com
(cherry picked from commit 66eb93e71a)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb8e30ddb7 ]
Back in commit 826cff3f7e ("drm/bridge: parade-ps8640: Enable
runtime power management") we removed a mysterious 50 ms delay because
"Parade's support [couldn't] explain what the delay [was] for".
While I'm always a fan of removing mysterious delays, I suspect that
we need this mysterious delay to avoid some problems.
Specifically, what I found recently is that on sc7180-trogdor-homestar
sometimes the AUX backlight wasn't initializing properly. Some
debugging showed that the drm_dp_dpcd_read() function that the AUX
backlight driver was calling was returning bogus data about 1% of the
time when I booted up. This confused
drm_panel_dp_aux_backlight(). From continued debugging:
- If I retried the read then the read worked just fine.
- If I added a loop to perform the same read that
drm_panel_dp_aux_backlight() was doing 30 times at bootup I could
see that some percentage of the time the first read would give bogus
data but all 29 additional reads would always be fine.
- If I added a large delay _after_ powering on the panel but before
powering on PS8640 I could still reproduce the problem.
- If I added a delay after PS8640 powered on then I couldn't reproduce
the problem.
- I couldn't reproduce the problem on a board with the same panel but
the ti-sn65dsi86 bridge chip.
To me, the above indicated that there was a problem with PS8640 and
not the panel.
I don't really have any insight into what's going on in the MCU, but
my best guess is that when the MCU itself sees the HPD go high that it
does some AUX transfers itself and this is confusing things.
Let's go back and add back in the mysterious 50 ms delay. We only want
to do this the first time we see HPD go high after booting the MCU,
not every time we double-check HPD.
With this, the backlight initializes reliably on homestar.
Fixes: 826cff3f7e ("drm/bridge: parade-ps8640: Enable runtime power management")
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221017121813.1.I59700c745fbc31559a5d5c8e2a960279c751dbd5@changeid
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 70445dee1b ]
DOWNSPREAD_CTRL (0x107) shall be cleared to 0 upon power-on reset or an
upstream device disconnect. This patch will enforce this rule by always
cleared DOWNSPREAD_CTRL register to 0 before start link training. At rare
case that DP MSA timing parameters may be mis-interpreted by the sink
which causes audio sampling rate be calculated wrongly and cause audio
did not work at sink if DOWNSPREAD_CTRL register is not cleared to 0.
Changes in v2:
1) fix spelling at commit text
2) merge ssc variable into encoding[0]
Changes in v3:
-- correct spelling of DOWNSPREAD_CTRL
-- replace err with len of ssize_t
Changes in v4:
-- split into 2 patches
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Fixes: c943b4948b ("drm/msm/dp: add displayPort driver support")
Patchwork: https://patchwork.freedesktop.org/patch/502532/
Link: https://lore.kernel.org/r/1662999830-13916-2-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a66124796 ]
DRM commit_tails() will disable downstream crtc/encoder/bridge if
both disable crtc is required and crtc->active is set before pushing
a new frame downstream.
There is a rare case that user space display manager issue an extra
screen update immediately followed by close DRM device while down
stream display interface is disabled. This extra screen update will
timeout due to the downstream interface is disabled but will cause
crtc->active be set. Hence the followed commit_tails() called by
drm_release() will pass the disable downstream crtc/encoder/bridge
conditions checking even downstream interface is disabled.
This cause the crash to happen at dp_bridge_disable() due to it trying
to access the main link register to push the idle pattern out while main
link clocks is disabled.
This patch adds atomic_check to prevent the extra frame will not
be pushed down if display interface is down so that crtc->active
will not be set neither. This will fail the conditions checking
of disabling down stream crtc/encoder/bridge which prevent
drm_release() from calling dp_bridge_disable() so that crash
at dp_bridge_disable() prevented.
There is no protection in the DRM framework to check if the display
pipeline has been already disabled before trying again. The only
check is the crtc_state->active but this is controlled by usermode
using UAPI. Hence if the usermode sets this and then crashes, the
driver needs to protect against double disable.
SError Interrupt on CPU7, code 0x00000000be000411 -- SError
CPU: 7 PID: 3878 Comm: Xorg Not tainted 5.19.0-stb-cbq #19
Hardware name: Google Lazor (rev3 - 8) (DT)
pstate: a04000c9 (NzCv daIF +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : __cmpxchg_case_acq_32+0x14/0x2c
lr : do_raw_spin_lock+0xa4/0xdc
sp : ffffffc01092b6a0
x29: ffffffc01092b6a0 x28: 0000000000000028 x27: 0000000000000038
x26: 0000000000000004 x25: ffffffd2973dce48 x24: 0000000000000000
x23: 00000000ffffffff x22: 00000000ffffffff x21: ffffffd2978d0008
x20: ffffffd2978d0008 x19: ffffff80ff759fc0 x18: 0000000000000000
x17: 004800a501260460 x16: 0441043b04600438 x15: 04380000089807d0
x14: 07b0089807800780 x13: 0000000000000000 x12: 0000000000000000
x11: 0000000000000438 x10: 00000000000007d0 x9 : ffffffd2973e09e4
x8 : ffffff8092d53300 x7 : ffffff808902e8b8 x6 : 0000000000000001
x5 : ffffff808902e880 x4 : 0000000000000000 x3 : ffffff80ff759fc0
x2 : 0000000000000001 x1 : 0000000000000000 x0 : ffffff80ff759fc0
Kernel panic - not syncing: Asynchronous SError Interrupt
CPU: 7 PID: 3878 Comm: Xorg Not tainted 5.19.0-stb-cbq #19
Hardware name: Google Lazor (rev3 - 8) (DT)
Call trace:
dump_backtrace.part.0+0xbc/0xe4
show_stack+0x24/0x70
dump_stack_lvl+0x68/0x84
dump_stack+0x18/0x34
panic+0x14c/0x32c
nmi_panic+0x58/0x7c
arm64_serror_panic+0x78/0x84
do_serror+0x40/0x64
el1h_64_error_handler+0x30/0x48
el1h_64_error+0x68/0x6c
__cmpxchg_case_acq_32+0x14/0x2c
_raw_spin_lock_irqsave+0x38/0x4c
lock_timer_base+0x40/0x78
__mod_timer+0xf4/0x25c
schedule_timeout+0xd4/0xfc
__wait_for_common+0xac/0x140
wait_for_completion_timeout+0x2c/0x54
dp_ctrl_push_idle+0x40/0x88
dp_bridge_disable+0x24/0x30
drm_atomic_bridge_chain_disable+0x90/0xbc
drm_atomic_helper_commit_modeset_disables+0x198/0x444
msm_atomic_commit_tail+0x1d0/0x374
commit_tail+0x80/0x108
drm_atomic_helper_commit+0x118/0x11c
drm_atomic_commit+0xb4/0xe0
drm_client_modeset_commit_atomic+0x184/0x224
drm_client_modeset_commit_locked+0x58/0x160
drm_client_modeset_commit+0x3c/0x64
__drm_fb_helper_restore_fbdev_mode_unlocked+0x98/0xac
drm_fb_helper_set_par+0x74/0x80
drm_fb_helper_hotplug_event+0xdc/0xe0
__drm_fb_helper_restore_fbdev_mode_unlocked+0x7c/0xac
drm_fb_helper_restore_fbdev_mode_unlocked+0x20/0x2c
drm_fb_helper_lastclose+0x20/0x2c
drm_lastclose+0x44/0x6c
drm_release+0x88/0xd4
__fput+0x104/0x220
____fput+0x1c/0x28
task_work_run+0x8c/0x100
do_exit+0x450/0x8d0
do_group_exit+0x40/0xac
__wake_up_parent+0x0/0x38
invoke_syscall+0x84/0x11c
el0_svc_common.constprop.0+0xb8/0xe4
do_el0_svc+0x8c/0xb8
el0_svc+0x2c/0x54
el0t_64_sync_handler+0x120/0x1c0
el0t_64_sync+0x190/0x194
SMP: stopping secondary CPUs
Kernel Offset: 0x128e800000 from 0xffffffc008000000
PHYS_OFFSET: 0x80000000
CPU features: 0x800,00c2a015,19801c82
Memory Limit: none
Changes in v2:
-- add more commit text
Changes in v3:
-- add comments into dp_bridge_atomic_check()
Changes in v4:
-- rewording the comment into dp_bridge_atomic_check()
Changes in v5:
-- removed quote x at end of commit text
Changes in v6:
-- removed quote x at end of comment in dp_bridge_atomic_check()
Fixes: 8a3b4c17f8 ("drm/msm/dp: employ bridge mechanism for display enable and disable")
Reported-by: Leonard Lausen <leonard@lausen.nl>
Suggested-by: Rob Clark <robdclark@gmail.com>
Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/17
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/505331/
Link: https://lore.kernel.org/r/1664408211-25314-1-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 809734c110 upstream.
This file was split in commit 5d945cbcd4
("drm/amd/display: Create a file dedicated to planes") and the logic in
dm_plane_format_mod_supported() function got changed by a switch logic.
That change broke drm_plane modifiers setting on series 5000 APUs
(tested on OXP mini AMD 5800U and HP Dev One 5850U PRO)
leading to Gamescope not working as reported on GitHub[1]
To reproduce the issue, enter a TTY and run:
$ gamescope -- vkcube
With said commit applied it will abort. This one restores the old logic,
fixing the issue that affects Gamescope.
[1](https://github.com/Plagman/gamescope/issues/624)
Cc: <stable@vger.kernel.org> # 6.0.x
Signed-off-by: Joaquín Ignacio Aramendía <samsagax@gmail.com>
Reviewed-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 79610d3041 upstream.
[WHY]
0, original pstate X
1, ctx_A_create -> ctx_A->stable_pstate = X
2, ctx_A_set_pstate (Y) -> current pstate is Y (PEAK or STANDARD)
3, ctx_B_create -> ctx_B->stable_pstate = Y
4, ctx_A_destroy -> restore pstate to X
5, ctx_B_destroy -> restore pstate to Y
Above sequence will cause final pstate is wrong (Y), should be original X.
[HOW]
When ctx_B create,
if ctx_A touched pstate setting
(not auto, stable_pstate_ctx != NULL),
set ctx_B->stable_pstate the same value as ctx_A saved,
if stable_pstate_ctx == NULL,
fetch current pstate to fill
ctx_B->stable_pstate.
Signed-off-by: Chengming Gui <Jack.Gui@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d61e1d1d52 upstream.
In the S2idle suspend/resume phase the gfxoff is keeping functional so
some IP blocks will be likely to reinitialize at gfxoff entry and that
will result in failing to program GC registers.Therefore, let disallow
gfxoff until AMDGPU IPs reinitialized completely.
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.15.x
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d2c4c1569a upstream.
MMHUB 2.1.x versions don't have ATCL2. Remove accesses to ATCL2 registers.
Since they are non-existing registers, read access will cause a
'Completer Abort' and gets reported when AER is enabled with the below patch.
Tagging with the patch so that this is backported along with it.
v2: squash in uninitialized warning fix (Nathan Chancellor)
Fixes: 8795e182b0 ("PCI/portdrv: Don't disable AER reporting in get_port_device_capability()")
Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8273b40486 upstream.
A user reported a bug on CAPE VERDE system where uvd_v3_1
IP component failed to initialize as there is an issue with
BO move code from one memory to other.
In function amdgpu_mem_visible() called by amdgpu_bo_move(),
when there are no blocks to compare or if we have a single
block then break the loop.
Fixes: 312b4dc11d ("drm/amdgpu: Fix VRAM BO swap issue")
Signed-off-by: Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: "Limonciello, Mario" <Mario.Limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 312b4dc11d upstream.
DRM buddy manager allocates the contiguous memory requests in
a single block or multiple blocks. So for the ttm move operation
(incase of low vram memory) we should consider all the blocks to
compute the total memory size which compared with the struct
ttm_resource num_pages in order to verify that the blocks are
contiguous for the eviction process.
v2: Added a Fixes tag
v3: Rewrite the code to save a bit of calculations and
variables (Christian)
Fixes: c9cad937c0 ("drm/amdgpu: add drm buddy support to amdgpu")
Signed-off-by: Arunpravin Paneer Selvam <Arunpravin.PaneerSelvam@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: "Limonciello, Mario" <Mario.Limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8a70b2d89e ]
Building 32-bit images may fail with the following error.
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn32/display_mode_vba_util_32.c:
In function ‘dml32_UseMinimumDCFCLK’:
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn32/display_mode_vba_util_32.c:3142:1:
error: the frame size of 1096 bytes is larger than 1024 bytes
This is seen when building i386:allmodconfig with any of the following
compilers.
gcc (Debian 12.2.0-3) 12.2.0
gcc (Ubuntu 9.4.0-1ubuntu1~20.04.1) 9.4.0
The problem is not seen if the compiler supports GCC_PLUGIN_LATENT_ENTROPY
because in that case CONFIG_FRAME_WARN is already set to 2048 even for
32-bit builds.
dml32_UseMinimumDCFCLK() was introduced with commit dda4fb85e4
("drm/amd/display: DML changes for DCN32/321"). It declares a large
number of local variables. Increase the frame size for the affected
file to 2048, similar to other files in the same directory, to enable
32-bit build tests with affected compilers.
Fixes: dda4fb85e4 ("drm/amd/display: DML changes for DCN32/321")
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reported-by: Łukasz Bartosik <ukaszb@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae71ab585c ]
This is a revert of commit fd5894fa24 ("drm/vc4: hdmi: Remove clock
rate initialization"), with the code slightly moved around.
It turns out that we can't downright remove that code from the driver,
since the Pi0-3 and Pi4 are in different cases, and it only works for
the Pi4.
Indeed, the commit mentioned above was relying on the RaspberryPi
firmware clocks driver to initialize the rate if it wasn't done by the
firmware. However, the Pi0-3 are using the clk-bcm2835 clock driver that
wasn't doing this initialization. We therefore end up with the clock not
being assigned a rate, and the CPU stalling when trying to access a
register.
We can't move that initialization in the clk-bcm2835 driver, since the
HSM clock we depend on is actually part of the HDMI power domain, so any
rate setup is only valid when the power domain is enabled. Thus, we
reinstated the minimum rate setup at runtime_suspend, which should
address both issues.
Link: https://lore.kernel.org/dri-devel/20220922145448.w3xfywkn5ecak2et@pengutronix.de/
Fixes: fd5894fa24 ("drm/vc4: hdmi: Remove clock rate initialization")
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220929-rpi-pi3-unplugged-fixes-v1-1-cd22e962296c@cerno.tech
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1c0b7de4d ]
The VC4 HDMI controller driver relies on the HDMI codec ASoC driver. In
order to set it up properly, in vc4_hdmi_audio_init(), our HDMI driver
will register a device matching the HDMI codec driver, and then register
an ASoC card using that codec.
However, if vc4 is compiled as a module, chances are that the hdmi-codec
driver will be too. In such a case, the module loader will have a very
narrow window to load the module between the device registration and the
card registration.
If it fails to load the module in time, the card registration will fail
with EPROBE_DEFER, and we'll abort the audio initialisation,
unregistering the HDMI codec device in the process.
The next time the bind callback will be run, it's likely that we end up
missing that window again, effectively preventing vc4 to probe entirely.
In order to prevent this, we can create a soft dependency of the vc4
driver on the HDMI codec one so that we're sure the HDMI codec will be
loaded before the VC4 module is, and thus we'll never end up in the
previous situation.
Fixes: 91e99e1139 ("drm/vc4: hdmi: Register HDMI codec")
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220902144111.3424560-1-maxime@cerno.tech
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 50b0e4d4da upstream.
Commit 8795e182b0 ("PCI/portdrv: Don't disable AER reporting in get_port_device_capability()")
uncovered a bug in amdgpu that required a reordering of the driver
init sequence to avoid accessing a special register on the GPU
before it was properly set up leading to an PCI AER error. This
reordering uncovered a different hw programming ordering dependency
in some APUs where the SDMA doorbells need to be programmed before
the GFX doorbells. To fix this, move the SDMA doorbell programming
back into the soc15 common code, but use the actual doorbell range
values directly rather than the values stored in the ring structure
since those will not be initialized at this point.
This is a partial revert, but with the doorbell assignment
fixed so the proper doorbell index is set before it's used.
Fixes: e3163bc8ff ("drm/amdgpu: move nbio sdma_doorbell_range() into sdma code for vega")
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: skhan@linuxfoundation.org
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d3a7051841 upstream.
The current scheme for generating the LFP data table pointers
(when the block including them is missing from the VBT) expects
the 0xffff sequence to only appear in the fp_timing terminator
entries. However some VBTs also have extra 0xffff sequences
elsewhere in the LFP data. When looking for the terminators
we may end up finding those extra sequeneces insted, which means
we deduce the wrong size for the fp_timing table. The code
then notices the inconsistent looking values and gives up on
the generated data table pointers, preventing us from parsing
the LFP data table entirely.
Let's give up on the "search for the terminators" approach
and instead just hardcode the expected size for the fp_timing
table.
We have enough sanity checks in place to make sure we
shouldn't end up parsing total garbage even if that size
should change in the future (although that seems unlikely
as the fp_timing and dvo_timing tables have been declared
obsolete as of VBT version 229).
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/6592
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220818192223.29881-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2130b87b22 upstream.
After commit 8799c0be89 ("drm/amd/display: Fix vblank refcount in vrr
transition"), a build with CONFIG_DEBUG_FS=n is broken due to a
misplaced brace, along the lines of:
In file included from drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm_trace.h:39,
from drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:41:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c: At top level:
./include/drm/drm_atomic.h:864:9: error: expected identifier or ‘(’ before ‘for’
864 | for ((__i) = 0; \
| ^~~
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:8317:9: note: in expansion of macro ‘for_each_new_crtc_in_state’
8317 | for_each_new_crtc_in_state(state, crtc, new_crtc_state, j)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
Move the brace within the #ifdef so that the file can be built with or
without CONFIG_DEBUG_FS.
Fixes: 8799c0be89 ("drm/amd/display: Fix vblank refcount in vrr transition")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b292cafe2d ]
This was fixed in initialize_cpsch before, but not in initialize_nocpsch.
Factor sdma bitmap initialization into a helper function to apply the
correct implementation in both cases without duplicating it.
v2: Added a range check
Reported-by: Ellis Michael <ellis@ellismichael.com>
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Graham Sider <Graham.Sider@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e32df0c7ec ]
[why]
vid stream control is double bufferred, if we don't wait for video
stream enable set to 0, we may get temporary image corruption
showing on the stream when setting PIXEL_TO_SYMBOL_FIFO_ENABLE to 0.
Reviewed-by: Ariel Bernstein <Eric.Bernstein@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97d8d6f075 ]
[why]
Only a single VLINE interrupt is available so interface should not
expose the second one which is used by DMU firmware.
[how]
Remove references to periodic_interrupt1 and VLINE1 from DC interfaces.
Reviewed-by: Jaehyun Chung <jaehyun.chung@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b4d8db657 ]
The sequence for Source DP PHY CTS automation is [2][1]:
1- Emulate successful Link Training(LT)
2- Short HPD and change link rates and number of lanes by LT.
(This is same flow for Link Layer CTS)
3- Short HPD and change PHY test pattern and swing/pre-emphasis
levels (This step should not trigger LT)
The problem is with DP PHY compliance setup as follow:
[DPTX + on board LTTPR]------Main Link--->[Scope]
^ |
| |
| |
----------Aux Ch------>[Aux Emulator]
At step 3, before writing TRAINING_LANEx_SET/LINK_QUAL_PATTERN_SET
to declare the pattern/swing requested by scope, we write link
config in LINK_BW_SET/LANE_COUNT_SET on a port that has LTTPR.
As LTTPR snoops aux transaction, LINK_BW_SET/LANE_COUNT_SET writes
indicate a LT will start [Check DP 2.0 E11 -Sec 3.6.8.2 & 3.6.8.6.3],
and LTTPR will reset the link and stop sending DP signals to
DPTX/Scope causing the measurements to fail. Note that step 3 will
not trigger LT and DP link will never recovered by the
Aux Emulator/Scope.
The reset of link can be tested with a monitor connected to LTTPR
port simply by writing to LINK_BW_SET or LANE_COUNT_SET as follow
igt/tools/dpcd_reg write --offset=0x100 --value 0x14 --device=2
OR
printf '\x14' | sudo dd of=/dev/drm_dp_aux2 bs=1 count=1 conv=notrunc
seek=$((0x100))
This single aux write causes the screen to blank, sending short HPD to
DPTX, setting LINK_STATUS_UPDATE = 1 in DPCD 0x204, and triggering LT.
As stated in [1]:
"Before any TX electrical testing can be performed, the link between a
DPTX and DPRX (in this case, a piece of test equipment), including all
LTTPRs within the path, shall be trained as defined in this Standard."
In addition, changing Phy pattern/Swing/Pre-emphasis (Step 3) uses the
same link rate and lane count applied on step 2, so no need to redo LT.
The fix is to not rewrite link config in step 3, and just writes
TRAINING_LANEx_SET and LINK_QUAL_PATTERN_SET
[1]: DP 2.0 E11 - 3.6.11.1 LTTPR DPTX_PHY Electrical Compliance
[2]: Configuring UnigrafDPTC Controller - Automation Test Sequence
https://www.keysight.com/us/en/assets/9922-01244/help-files/
D9040DPPC-DisplayPort-Test-Software-Online-Help-latest.chm
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Or Cochvi <or.cochvi@intel.com>
Signed-off-by: Khaled Almahallawy <khaled.almahallawy@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220916054900.415804-1-khaled.almahallawy@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
