[ Upstream commit aae425efdf ]
During reallocation of RX buffers, new DMA mappings are created for
those buffers.
steps for reproduction:
while :
do
for ((i=0; i<=8160; i=i+32))
do
ethtool -G enp130s0f0 rx $i tx $i
sleep 0.5
ethtool -g enp130s0f0
done
done
This resulted in crash:
i40e 0000:01:00.1: Unable to allocate memory for the Rx descriptor ring, size=65536
Driver BUG
WARNING: CPU: 0 PID: 4300 at net/core/xdp.c:141 xdp_rxq_info_unreg+0x43/0x50
Call Trace:
i40e_free_rx_resources+0x70/0x80 [i40e]
i40e_set_ringparam+0x27c/0x800 [i40e]
ethnl_set_rings+0x1b2/0x290
genl_family_rcv_msg_doit.isra.15+0x10f/0x150
genl_family_rcv_msg+0xb3/0x160
? rings_fill_reply+0x1a0/0x1a0
genl_rcv_msg+0x47/0x90
? genl_family_rcv_msg+0x160/0x160
netlink_rcv_skb+0x4c/0x120
genl_rcv+0x24/0x40
netlink_unicast+0x196/0x230
netlink_sendmsg+0x204/0x3d0
sock_sendmsg+0x4c/0x50
__sys_sendto+0xee/0x160
? handle_mm_fault+0xbe/0x1e0
? syscall_trace_enter+0x1d3/0x2c0
__x64_sys_sendto+0x24/0x30
do_syscall_64+0x5b/0x1a0
entry_SYSCALL_64_after_hwframe+0x65/0xca
RIP: 0033:0x7f5eac8b035b
Missing register, driver bug
WARNING: CPU: 0 PID: 4300 at net/core/xdp.c:119 xdp_rxq_info_unreg_mem_model+0x69/0x140
Call Trace:
xdp_rxq_info_unreg+0x1e/0x50
i40e_free_rx_resources+0x70/0x80 [i40e]
i40e_set_ringparam+0x27c/0x800 [i40e]
ethnl_set_rings+0x1b2/0x290
genl_family_rcv_msg_doit.isra.15+0x10f/0x150
genl_family_rcv_msg+0xb3/0x160
? rings_fill_reply+0x1a0/0x1a0
genl_rcv_msg+0x47/0x90
? genl_family_rcv_msg+0x160/0x160
netlink_rcv_skb+0x4c/0x120
genl_rcv+0x24/0x40
netlink_unicast+0x196/0x230
netlink_sendmsg+0x204/0x3d0
sock_sendmsg+0x4c/0x50
__sys_sendto+0xee/0x160
? handle_mm_fault+0xbe/0x1e0
? syscall_trace_enter+0x1d3/0x2c0
__x64_sys_sendto+0x24/0x30
do_syscall_64+0x5b/0x1a0
entry_SYSCALL_64_after_hwframe+0x65/0xca
RIP: 0033:0x7f5eac8b035b
This was caused because of new buffers with different RX ring count should
substitute older ones, but those buffers were freed in
i40e_configure_rx_ring and reallocated again with i40e_alloc_rx_bi,
thus kfree on rx_bi caused leak of already mapped DMA.
Fix this by reallocating ZC with rx_bi_zc struct when BPF program loads. Additionally
reallocate back to rx_bi when BPF program unloads.
If BPF program is loaded/unloaded and XSK pools are created, reallocate
RX queues accordingly in XSP_SETUP_XSK_POOL handler.
Fixes: be1222b585 ("i40e: Separate kernel allocated rx_bi rings from AF_XDP rings")
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Chandan <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 35bbe652c4 upstream.
davinci_mdio.c uses mdio bitbang APIs, so it should select
MDIO_BITBANG to prevent build errors.
arm-linux-gnueabi-ld: drivers/net/ethernet/ti/davinci_mdio.o: in function `davinci_mdio_remove':
drivers/net/ethernet/ti/davinci_mdio.c:649: undefined reference to `free_mdio_bitbang'
arm-linux-gnueabi-ld: drivers/net/ethernet/ti/davinci_mdio.o: in function `davinci_mdio_probe':
drivers/net/ethernet/ti/davinci_mdio.c:545: undefined reference to `alloc_mdio_bitbang'
arm-linux-gnueabi-ld: drivers/net/ethernet/ti/davinci_mdio.o: in function `davinci_mdiobb_read':
drivers/net/ethernet/ti/davinci_mdio.c:236: undefined reference to `mdiobb_read'
arm-linux-gnueabi-ld: drivers/net/ethernet/ti/davinci_mdio.o: in function `davinci_mdiobb_write':
drivers/net/ethernet/ti/davinci_mdio.c:253: undefined reference to `mdiobb_write'
Fixes: d04807b806 ("net: ethernet: ti: davinci_mdio: Add workaround for errata i2329")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Ravi Gunasekaran <r-gunasekaran@ti.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Naresh Kamboju <naresh.kamboju@linaro.org>
Cc: Sudip Mukherjee (Codethink) <sudipm.mukherjee@gmail.com>
Link: https://lore.kernel.org/r/20220824024216.4939-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8db3d514e9 ]
Any change to the hardware timestamps configuration triggers nic restart,
which breaks transmition and reception of network packets for a while.
But there is no need to fully restart the device because while configuring
hardware timestamps. The code for changing configuration runs after all
of the initialisation, when the NIC is actually up and running. This patch
changes the code that ioctl will only update configuration registers and
will not trigger carrier status change, but in case of timestamps for
all rx packetes it fallbacks to close()/open() sequnce because of
synchronization issues in the hardware. Tested on BCM57504.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Vadim Fedorenko <vfedorenko@novek.ru>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20220922191038.29921-1-vfedorenko@novek.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11c12adcbc ]
During stress tests with adding VF to namespace and changing vf's
trust there was a race between iavf_reset_task and iavf_close.
Sometimes when IAVF_FLAG_AQ_DISABLE_QUEUES from iavf_close was sent
to PF after reset and before IAVF_AQ_GET_CONFIG was sent then PF
returns error IAVF_NOT_SUPPORTED to disable queues request and
following requests. There is need to get_config before other
aq_required will be send but iavf_close clears all flags, if
get_config was not sent before iavf_close, then it will not be send
at all.
In case when IAVF_FLAG_AQ_GET_OFFLOAD_VLAN_V2_CAPS was sent before
IAVF_FLAG_AQ_DISABLE_QUEUES then there was rtnl_lock deadlock
between iavf_close and iavf_adminq_task until iavf_close timeouts
and disable queues was sent after iavf_close ends.
There was also a problem with sending delete/add filters.
Sometimes when filters was not yet added to PF and in
iavf_close all filters was set to remove there might be a try
to remove nonexistent filters on PF.
Add aq_required_tmp to save aq_required flags and send them after
disable_queues will be handled. Clear flags given to iavf_down
different than IAVF_FLAG_AQ_GET_CONFIG as this flag is necessary
to sent other aq_required. Remove some flags that we don't
want to send as we are in iavf_close and we want to disable
interface. Remove filters which was not yet sent and send del
filters flags only when there are filters to remove.
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9df696b3b3 ]
Sparse found a number of endianness-related issues of these kinds:
.../ftmac100.c:192:32: warning: restricted __le32 degrades to integer
.../ftmac100.c:208:23: warning: incorrect type in assignment (different base types)
.../ftmac100.c:208:23: expected unsigned int rxdes0
.../ftmac100.c:208:23: got restricted __le32 [usertype]
.../ftmac100.c:249:23: warning: invalid assignment: &=
.../ftmac100.c:249:23: left side has type unsigned int
.../ftmac100.c:249:23: right side has type restricted __le32
.../ftmac100.c:527:16: warning: cast to restricted __le32
Change type of some fields from 'unsigned int' to '__le32' to fix it.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220902113749.1408562-1-saproj@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fef5de753f ]
Issue found during code review. This bug has no impact as long as the
ks8851_net structure is the first element of the ks8851_net_spi structure.
As long as the offset to the ks8851_net struct is zero, the container_of()
macro is subtracting 0 and therefore no damage done. But if the
ks8851_net_spi struct is ever modified such that the ks8851_net struct
within it is no longer the first element of the struct, then the bug would
manifest itself and cause problems.
struct ks8851_net is contained within ks8851_net_spi.
ks is contained within kss.
kss is the priv_data of the netdev structure.
Signed-off-by: Jerry Ray <jerry.ray@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d04807b806 ]
On the CPSW and ICSS peripherals, there is a possibility that the MDIO
interface returns corrupt data on MDIO reads or writes incorrect data
on MDIO writes. There is also a possibility for the MDIO interface to
become unavailable until the next peripheral reset.
The workaround is to configure the MDIO in manual mode and disable the
MDIO state machine and emulate the MDIO protocol by reading and writing
appropriate fields in MDIO_MANUAL_IF_REG register of the MDIO controller
to manipulate the MDIO clock and data pins.
More details about the errata i2329 and the workaround is available in:
https://www.ti.com/lit/er/sprz487a/sprz487a.pdf
Add implementation to disable MDIO state machine, configure MDIO in manual
mode and achieve MDIO read and writes via MDIO Bitbanging
Signed-off-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0152dfee23 ]
When mvpp2 is unloaded, the driver specific debugfs directory is not
removed, which technically leads to a memory leak. However, this
directory is only created when the first device is probed, so the
hardware is present. Removing the module is only something a developer
would to when e.g. testing out changes, so the module would be
reloaded. So this memory leak is minor.
The original attempt in commit fe2c9c61f6 ("net: mvpp2: debugfs: fix
memory leak when using debugfs_lookup()") that was labelled as a memory
leak fix was not, it fixed a refcount leak, but in doing so created a
problem when the module is reloaded - the directory already exists, but
mvpp2_root is NULL, so we lose all debugfs entries. This fix has been
reverted.
This is the alternative fix, where we remove the offending directory
whenever the driver is unloaded.
Fixes: 21da57a231 ("net: mvpp2: add a debugfs interface for the Header Parser")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Marcin Wojtas <mw@semihalf.com>
Link: https://lore.kernel.org/r/E1ofOAB-00CzkG-UO@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12aece8b01 ]
This frees "mac" and tries to display its address as part of the error
message on the next line. Swap the order.
Fixes: fd3040b939 ("net: ethernet: Add driver for Sunplus SP7021")
Signed-off-by: Zheng Wang <zyytlz.wz@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b43f9acbb8 ]
bnx2x_tpa_stop() allocates a memory chunk from new_data with
bnx2x_frag_alloc(). The new_data should be freed when gets some error.
But when "pad + len > fp->rx_buf_size" is true, bnx2x_tpa_stop() returns
without releasing the new_data, which will lead to a memory leak.
We should free the new_data with bnx2x_frag_free() when "pad + len >
fp->rx_buf_size" is true.
Fixes: 07b0f00964 ("bnx2x: fix possible panic under memory stress")
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb4b12071a ]
Remove PTP_PF_EXTTS support for non-PCI11x1x devices since they do not support
the PTP-IO Input event triggered timestamping mechanisms added
Fixes: 60942c397a ("net: lan743x: Add support for PTP-IO Event Input External Timestamp (extts)")
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e6fd874c7 ]
As the kemdup could return NULL, it should be better to check the return
value and return error if fails.
Moreover, the return value of prestera_acl_ruleset_keymask_set() should
be checked by cascade.
Fixes: 604ba23090 ("net: prestera: flower template support")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Reviewed-by: Taras Chornyi<tchornyi@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ad1c94e1e ]
Zbynek reports that alx trips an rtnl assertion on resume:
RTNL: assertion failed at net/core/dev.c (2891)
RIP: 0010:netif_set_real_num_tx_queues+0x1ac/0x1c0
Call Trace:
<TASK>
__alx_open+0x230/0x570 [alx]
alx_resume+0x54/0x80 [alx]
? pci_legacy_resume+0x80/0x80
dpm_run_callback+0x4a/0x150
device_resume+0x8b/0x190
async_resume+0x19/0x30
async_run_entry_fn+0x30/0x130
process_one_work+0x1e5/0x3b0
indeed the driver does not hold rtnl_lock during its internal close
and re-open functions during suspend/resume. Note that this is not
a huge bug as the driver implements its own locking, and does not
implement changing the number of queues, but we need to silence
the splat.
Fixes: 4a5fe57e77 ("alx: use fine-grained locking instead of RTNL")
Reported-and-tested-by: Zbynek Michl <zbynek.michl@gmail.com>
Reviewed-by: Niels Dossche <dossche.niels@gmail.com>
Link: https://lore.kernel.org/r/20220928181236.1053043-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3b173745c ]
When the user changes the number of queues via ethtool, the driver
allocates new rings. This allocation did not initialize tx_tstamps. This
results in the tx_tstamps field being zero (due to kcalloc allocation), and
would result in a NULL pointer dereference when attempting a transmit
timestamp on the new ring.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stable-dep-of: fc5ae5b44e ("Bluetooth: L2CAP: Fix build errors in some archs")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 704438dd4f ]
Port event data must stored to port-state cache regardless of whether
the port uses phylink or not since this data is used by ethtool.
Fixes: 52323ef754 ("net: marvell: prestera: add phylink support")
Signed-off-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
Signed-off-by: Maksym Glubokiy <maksym.glubokiy@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7d8dd6b5cd ]
Fixed register define is not used, but register definition shall be kept
in sync.
Fixes: 403f69bbdb ("tsnep: Add TSN endpoint Ethernet MAC driver")
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit ae3ed15da5 upstream.
Setting ib1 state to MTK_FOE_STATE_UNBIND in __mtk_foe_entry_clear
routine as done by commit 0e80707d94 ("net: ethernet: mtk_eth_soc:
fix typo in __mtk_foe_entry_clear") breaks flow offloading, at least
on older MTK_NETSYS_V1 SoCs, OpenWrt users have confirmed the bug on
MT7622 and MT7621 systems.
Felix Fietkau suggested to use MTK_FOE_STATE_INVALID instead which
works well on both, MTK_NETSYS_V1 and MTK_NETSYS_V2.
Tested on MT7622 (Linksys E8450) and MT7986 (BananaPi BPI-R3).
Suggested-by: Felix Fietkau <nbd@nbd.name>
Fixes: 0e80707d94 ("net: ethernet: mtk_eth_soc: fix typo in __mtk_foe_entry_clear")
Fixes: 33fc42de33 ("net: ethernet: mtk_eth_soc: support creating mac address based offload entries")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/YzY+1Yg0FBXcnrtc@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tony Nguyen says:
====================
ice: xsk: ZC changes
Maciej Fijalkowski says:
This set consists of two fixes to issues that were either pointed out on
indirectly (John was reviewing AF_XDP selftests that were testing ice's
ZC support) mailing list or were directly reported by customers.
First patch allows user space to see done descriptor in CQ even after a
single frame being transmitted and second patch removes the need for
having HW rings sized to power of 2 number of descriptors when used
against AF_XDP.
I also forgot to mention that due to the current Tx cleaning algorithm,
4k HW ring was broken and these two patches bring it back to life, so we
kill two birds with one stone.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: xsk: drop power of 2 ring size restriction for AF_XDP
ice: xsk: change batched Tx descriptor cleaning
====================
Link: https://lore.kernel.org/r/20220927164112.4011983-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently the following set of commands fails:
$ ip link add br0 type bridge # vlan_filtering 0
$ ip link set swp0 master br0
$ bridge vlan
port vlan-id
swp0 1 PVID Egress Untagged
$ bridge vlan add dev swp0 vid 10
Error: mscc_ocelot_switch_lib: Port with more than one egress-untagged VLAN cannot have egress-tagged VLANs.
Dumping ocelot->vlans, one can see that the 2 egress-untagged VLANs on swp0 are
vid 1 (the bridge PVID) and vid 4094, a PVID used privately by the driver for
VLAN-unaware bridging. So this is why bridge vid 10 is refused, despite
'bridge vlan' showing a single egress untagged VLAN.
As mentioned in the comment added, having this private VLAN does not impose
restrictions to the hardware configuration, yet it is a bookkeeping problem.
There are 2 possible solutions.
One is to make the functions that operate on VLAN-unaware pvids:
- ocelot_add_vlan_unaware_pvid()
- ocelot_del_vlan_unaware_pvid()
- ocelot_port_setup_dsa_8021q_cpu()
- ocelot_port_teardown_dsa_8021q_cpu()
call something different than ocelot_vlan_member_(add|del)(), the latter being
the real problem, because it allocates a struct ocelot_bridge_vlan *vlan which
it adds to ocelot->vlans. We don't really *need* the private VLANs in
ocelot->vlans, it's just that we have the extra convenience of having the
vlan->portmask cached in software (whereas without these structures, we'd have
to create a raw ocelot_vlant_rmw_mask() procedure which reads back the current
port mask from hardware).
The other solution is to filter out the private VLANs from
ocelot_port_num_untagged_vlans(), since they aren't what callers care about.
We only need to do this to the mentioned function and not to
ocelot_port_num_tagged_vlans(), because private VLANs are never egress-tagged.
Nothing else seems to be broken in either solution, but the first one requires
more rework which will conflict with the net-next change 36a0bf4435 ("net:
mscc: ocelot: set up tag_8021q CPU ports independent of user port affinity"),
and I'd like to avoid that. So go with the other one.
Fixes: 54c3198460 ("net: mscc: ocelot: enforce FDB isolation when VLAN-unaware")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220927122042.1100231-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
AF_XDP Tx descriptor cleaning in ice driver currently works in a "lazy"
way - descriptors are not cleaned immediately after send. We rather hold
on with cleaning until we see that free space in ring drops below
particular threshold. This was supposed to reduce the amount of
unnecessary work related to cleaning and instead of keeping the ring
empty, ring was rather saturated.
In AF_XDP realm cleaning Tx descriptors implies producing them to CQ.
This is a way of letting know user space that particular descriptor has
been sent, as John points out in [0].
We tried to implement serial descriptor cleaning which would be used in
conjunction with batched cleaning but it made code base more convoluted
and probably harder to maintain in future. Therefore we step away from
batched cleaning in a current form in favor of an approach where we set
RS bit on every last descriptor from a batch and clean always at the
beginning of ice_xmit_zc().
This means that we give up a bit of Tx performance, but this doesn't
hurt l2fwd scenario which is way more meaningful than txonly as this can
be treaten as AF_XDP based packet generator. l2fwd is not hurt due to
the fact that Tx side is much faster than Rx and Rx is the one that has
to catch Tx up.
FWIW Tx descriptors are still produced in a batched way.
[0]: https://lore.kernel.org/bpf/62b0a20232920_3573208ab@john.notmuch/
Fixes: 126cdfe100 ("ice: xsk: Improve AF_XDP ZC Tx and use batching API")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This commit fixes DMA engine reset timeout issue in suspend/resume
with ADLink I-Pi SMARC Plus board which dmesg shows:
...
[ 54.678271] PM: suspend exit
[ 54.754066] intel-eth-pci 0000:00:1d.2 enp0s29f2: PHY [stmmac-3:01] driver [Maxlinear Ethernet GPY215B] (irq=POLL)
[ 54.755808] intel-eth-pci 0000:00:1d.2 enp0s29f2: Register MEM_TYPE_PAGE_POOL RxQ-0
...
[ 54.780482] intel-eth-pci 0000:00:1d.2 enp0s29f2: Register MEM_TYPE_PAGE_POOL RxQ-7
[ 55.784098] intel-eth-pci 0000:00:1d.2: Failed to reset the dma
[ 55.784111] intel-eth-pci 0000:00:1d.2 enp0s29f2: stmmac_hw_setup: DMA engine initialization failed
[ 55.784115] intel-eth-pci 0000:00:1d.2 enp0s29f2: stmmac_open: Hw setup failed
...
The issue is related with serdes which impacts clock. There is
serdes in ADLink I-Pi SMARC board ethernet controller. Please refer to
commit b9663b7ca6 ("net: stmmac: Enable SERDES power up/down sequence")
for detial. When issue is reproduced, DMA engine clock is not ready
because serdes is not powered up.
To reproduce DMA engine reset timeout issue with hardware which has
serdes in GBE controller, install Ubuntu. In Ubuntu GUI, click
"Power Off/Log Out" -> "Suspend" menu, it disables network interface,
then goes to sleep mode. When it wakes up, it enables network
interface again. Stmmac driver is called in this way:
1. stmmac_release: Stop network interface. In this function, it
disables DMA engine and network interface;
2. stmmac_suspend: It is called in kernel suspend flow. But because
network interface has been disabled(netif_running(ndev) is
false), it does nothing and returns directly;
3. System goes into S3 or S0ix state. Some time later, system is
waken up by keyboard or mouse;
4. stmmac_resume: It does nothing because network interface has
been disabled;
5. stmmac_open: It is called to enable network interace again. DMA
engine is initialized in this API, but serdes is not power on so
there will be DMA engine reset timeout issue.
Similarly, serdes powerdown should be added in stmmac_release.
Network interface might be disabled by cmd "ifconfig eth0 down",
DMA engine, phy and mac have been disabled in ndo_stop callback,
serdes should be powered down as well. It doesn't make sense that
serdes is on while other components have been turned off.
If ethernet interface is in enabled state(netif_running(ndev) is true)
before suspend/resume, the issue couldn't be reproduced because serdes
could be powered up in stmmac_resume.
Because serdes_powerup is added in stmmac_open, it doesn't need to be
called in probe function.
Fixes: b9663b7ca6 ("net: stmmac: Enable SERDES power up/down sequence")
Signed-off-by: Junxiao Chang <junxiao.chang@intel.com>
Reviewed-by: Voon Weifeng <weifeng.voon@intel.com>
Tested-by: Jimmy JS Chen <jimmyjs.chen@adlinktech.com>
Tested-by: Looi, Hong Aun <hong.aun.looi@intel.com>
Link: https://lore.kernel.org/r/20220923050448.1220250-1-junxiao.chang@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The label passed to the QDESC_GET for the ETHOFLD TXQ, RXQ, and FLQ, is the
'out' one, which skips the 'out_unlock' label, and thus doesn't unlock the
'uld_mutex' before returning. Additionally, since commit 5148e5950c
("cxgb4: add EOTID tracking and software context dump"), the access to
these ETHOFLD hardware queues should be protected by the 'mqprio_mutex'
instead.
Fixes: 2d0cb84dd9 ("cxgb4: add ETHOFLD hardware queue support")
Fixes: 5148e5950c ("cxgb4: add EOTID tracking and software context dump")
Signed-off-by: Rafael Mendonca <rafaelmendsr@gmail.com>
Reviewed-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Link: https://lore.kernel.org/r/20220922175109.764898-1-rafaelmendsr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit fe2c9c61f6.
On Tue, Sep 13, 2022 at 05:48:58PM +0100, Russell King (Oracle) wrote:
>What happens if this is built as a module, and the module is loaded,
>binds (and creates the directory), then is removed, and then re-
>inserted? Nothing removes the old directory, so doesn't
>debugfs_create_dir() fail, resulting in subsequent failure to add
>any subsequent debugfs entries?
>
>I don't think this patch should be backported to stable trees until
>this point is addressed.
Revert until a proper fix is available as the original behavior was
better.
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: stable@kernel.org
Reported-by: Russell King <linux@armlinux.org.uk>
Fixes: fe2c9c61f6 ("net: mvpp2: debugfs: fix memory leak when using debugfs_lookup()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20220923234736.657413-1-sashal@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When GEM is in SGMII mode and disabled as a wakeup source, the power
management controller can power down the entire full power domain(FPD)
if none of the FPD devices are in use.
Incase of FPD off, there are below ethernet link up issues on non-wakeup
suspend/resume. To fix it add phy_exit() in suspend and phy_init() in the
resume path which reinitializes PS GTR SGMII lanes.
$ echo +20 > /sys/class/rtc/rtc0/wakealarm
$ echo mem > /sys/power/state
After resume:
$ ifconfig eth0 up
xilinx-psgtr fd400000.phy: lane 0 (type 10, protocol 5): PLL lock timeout
phy phy-fd400000.phy.0: phy poweron failed --> -110
xilinx-psgtr fd400000.phy: lane 0 (type 10, protocol 5): PLL lock timeout
SIOCSIFFLAGS: Connection timed out
phy phy-fd400000.phy.0: phy poweron failed --> -110
Fixes: 8b73fa3ae0 ("net: macb: Added ZynqMP-specific initialization")
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from Jakub Kicinski:
"Including fixes from wifi, netfilter and can.
A handful of awaited fixes here - revert of the FEC changes, bluetooth
fix, fixes for iwlwifi spew.
We added a warning in PHY/MDIO code which is triggering on a couple of
platforms in a false-positive-ish way. If we can't iron that out over
the week we'll drop it and re-add for 6.1.
I've added a new "follow up fixes" section for fixes to fixes in
6.0-rcs but it may actually give the false impression that those are
problematic or that more testing time would have caught them. So
likely a one time thing.
Follow up fixes:
- nf_tables_addchain: fix nft_counters_enabled underflow
- ebtables: fix memory leak when blob is malformed
- nf_ct_ftp: fix deadlock when nat rewrite is needed
Current release - regressions:
- Revert "fec: Restart PPS after link state change" and the related
"net: fec: Use a spinlock to guard `fep->ptp_clk_on`"
- Bluetooth: fix HCIGETDEVINFO regression
- wifi: mt76: fix 5 GHz connection regression on mt76x0/mt76x2
- mptcp: fix fwd memory accounting on coalesce
- rwlock removal fall out:
- ipmr: always call ip{,6}_mr_forward() from RCU read-side
critical section
- ipv6: fix crash when IPv6 is administratively disabled
- tcp: read multiple skbs in tcp_read_skb()
- mdio_bus_phy_resume state warning fallout:
- eth: ravb: fix PHY state warning splat during system resume
- eth: sh_eth: fix PHY state warning splat during system resume
Current release - new code bugs:
- wifi: iwlwifi: don't spam logs with NSS>2 messages
- eth: mtk_eth_soc: enable XDP support just for MT7986 SoC
Previous releases - regressions:
- bonding: fix NULL deref in bond_rr_gen_slave_id
- wifi: iwlwifi: mark IWLMEI as broken
Previous releases - always broken:
- nf_conntrack helpers:
- irc: tighten matching on DCC message
- sip: fix ct_sip_walk_headers
- osf: fix possible bogus match in nf_osf_find()
- ipvlan: fix out-of-bound bugs caused by unset skb->mac_header
- core: fix flow symmetric hash
- bonding, team: unsync device addresses on ndo_stop
- phy: micrel: fix shared interrupt on LAN8814"
* tag 'net-6.0-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (83 commits)
selftests: forwarding: add shebang for sch_red.sh
bnxt: prevent skb UAF after handing over to PTP worker
net: marvell: Fix refcounting bugs in prestera_port_sfp_bind()
net: sched: fix possible refcount leak in tc_new_tfilter()
net: sunhme: Fix packet reception for len < RX_COPY_THRESHOLD
udp: Use WARN_ON_ONCE() in udp_read_skb()
selftests: bonding: cause oops in bond_rr_gen_slave_id
bonding: fix NULL deref in bond_rr_gen_slave_id
net: phy: micrel: fix shared interrupt on LAN8814
net/smc: Stop the CLC flow if no link to map buffers on
ice: Fix ice_xdp_xmit() when XDP TX queue number is not sufficient
net: atlantic: fix potential memory leak in aq_ndev_close()
can: gs_usb: gs_usb_set_phys_id(): return with error if identify is not supported
can: gs_usb: gs_can_open(): fix race dev->can.state condition
can: flexcan: flexcan_mailbox_read() fix return value for drop = true
net: sh_eth: Fix PHY state warning splat during system resume
net: ravb: Fix PHY state warning splat during system resume
netfilter: nf_ct_ftp: fix deadlock when nat rewrite is needed
netfilter: ebtables: fix memory leak when blob is malformed
netfilter: nf_tables: fix percpu memory leak at nf_tables_addchain()
...
When reading the timestamp is required bnxt_tx_int() hands
over the ownership of the completed skb to the PTP worker.
The skb should not be used afterwards, as the worker may
run before the rest of our code and free the skb, leading
to a use-after-free.
Since dev_kfree_skb_any() accepts NULL make the loss of
ownership more obvious and set skb to NULL.
Fixes: 83bb623c96 ("bnxt_en: Transmit and retrieve packet timestamps")
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20220921201005.335390-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In prestera_port_sfp_bind(), there are two refcounting bugs:
(1) we should call of_node_get() before of_find_node_by_name() as
it will automaitcally decrease the refcount of 'from' argument;
(2) we should call of_node_put() for the break of the iteration
for_each_child_of_node() as it will automatically increase and
decrease the 'child'.
Fixes: 52323ef754 ("net: marvell: prestera: add phylink support")
Signed-off-by: Liang He <windhl@126.com>
Reviewed-by: Yevhen Orlov <yevhen.orlov@plvision.eu>
Link: https://lore.kernel.org/r/20220921133245.4111672-1-windhl@126.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is a separate receive path for small packets (under 256 bytes).
Instead of allocating a new dma-capable skb to be used for the next packet,
this path allocates a skb and copies the data into it (reusing the existing
sbk for the next packet). There are two bytes of junk data at the beginning
of every packet. I believe these are inserted in order to allow aligned DMA
and IP headers. We skip over them using skb_reserve. Before copying over
the data, we must use a barrier to ensure we see the whole packet. The
current code only synchronizes len bytes, starting from the beginning of
the packet, including the junk bytes. However, this leaves off the final
two bytes in the packet. Synchronize the whole packet.
To reproduce this problem, ping a HME with a payload size between 17 and
214
$ ping -s 17 <hme_address>
which will complain rather loudly about the data mismatch. Small packets
(below 60 bytes on the wire) do not have this issue. I suspect this is
related to the padding added to increase the minimum packet size.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220920235018.1675956-1-seanga2@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-09-20 (ice)
Michal re-sets TC configuration when changing number of queues.
Mateusz moves the check and call for link-down-on-close to the specific
path for downing/closing the interface.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: Fix interface being down after reset with link-down-on-close flag on
ice: config netdev tc before setting queues number
====================
Link: https://lore.kernel.org/r/20220920205344.1860934-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The original patch added the static branch to handle the situation,
when assigning an XDP TX queue to every CPU is not possible,
so they have to be shared.
However, in the XDP transmit handler ice_xdp_xmit(), an error was
returned in such cases even before static condition was checked,
thus making queue sharing still impossible.
Fixes: 22bf877e52 ("ice: introduce XDP_TX fallback path")
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/r/20220919134346.25030-1-larysa.zaremba@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-09-19 (iavf, i40e)
Norbert adds checking of buffer size for Rx buffer checks in iavf.
Michal corrects setting of max MTU in iavf to account for MTU data provided
by PF, fixes i40e to set VF max MTU, and resolves lack of rate limiting
when value was less than divisor for i40e.
* '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
i40e: Fix set max_tx_rate when it is lower than 1 Mbps
i40e: Fix VF set max MTU size
iavf: Fix set max MTU size with port VLAN and jumbo frames
iavf: Fix bad page state
====================
Link: https://lore.kernel.org/r/20220919223428.572091-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If aq_nic_stop() fails, aq_ndev_close() returns err without calling
aq_nic_deinit() to release the relevant memory and resource, which
will lead to a memory leak.
We can fix it by deleting the if condition judgment and goto statement to
call aq_nic_deinit() directly after aq_nic_stop() to fix the memory leak.
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 744d23c71a ("net: phy: Warn about incorrect
mdio_bus_phy_resume() state"), a warning splat is printed during system
resume with Wake-on-LAN disabled:
WARNING: CPU: 0 PID: 626 at drivers/net/phy/phy_device.c:323 mdio_bus_phy_resume+0xbc/0xe4
As the Renesas SuperH Ethernet driver already calls phy_{stop,start}()
in its suspend/resume callbacks, it is sufficient to just mark the MAC
responsible for managing the power state of the PHY.
Fixes: fba863b816 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/c6e1331b9bef61225fa4c09db3ba3e2e7214ba2d.1663598886.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Since commit 744d23c71a ("net: phy: Warn about incorrect
mdio_bus_phy_resume() state"), a warning splat is printed during system
resume with Wake-on-LAN disabled:
WARNING: CPU: 0 PID: 1197 at drivers/net/phy/phy_device.c:323 mdio_bus_phy_resume+0xbc/0xc8
As the Renesas Ethernet AVB driver already calls phy_{stop,start}() in
its suspend/resume callbacks, it is sufficient to just mark the MAC
responsible for managing the power state of the PHY.
Fixes: fba863b816 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/8ec796f47620980fdd0403e21bd8b7200b4fa1d4.1663598796.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When performing a reset on ice driver with link-down-on-close flag on
interface would always stay down. Fix this by moving a check of this
flag to ice_stop() that is called only when user wants to bring
interface down.
Fixes: ab4ab73fc1 ("ice: Add ethtool private flag to make forcing link down optional")
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Petr Oros <poros@redhat.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After lowering number of tx queues the warning appears:
"Number of in use tx queues changed invalidating tc mappings. Priority
traffic classification disabled!"
Example command to reproduce:
ethtool -L enp24s0f0 tx 36 rx 36
Fix this by setting correct tc mapping before setting real number of
queues on netdev.
Fixes: 0754d65bd4 ("ice: Add infrastructure for mqprio support via ndo_setup_tc")
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
TSN features on the ENETC (taprio, cbs, gate, police) are configured
through a mix of command BD ring messages and port registers:
enetc_port_rd(), enetc_port_wr().
Port registers are a region of the ENETC memory map which are only
accessible from the PCIe Physical Function. They are not accessible from
the Virtual Functions.
Moreover, attempting to access these registers crashes the kernel:
$ echo 1 > /sys/bus/pci/devices/0000\:00\:00.0/sriov_numvfs
pci 0000:00:01.0: [1957:ef00] type 00 class 0x020001
fsl_enetc_vf 0000:00:01.0: Adding to iommu group 15
fsl_enetc_vf 0000:00:01.0: enabling device (0000 -> 0002)
fsl_enetc_vf 0000:00:01.0 eno0vf0: renamed from eth0
$ tc qdisc replace dev eno0vf0 root taprio num_tc 8 map 0 1 2 3 4 5 6 7 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 base-time 0 \
sched-entry S 0x7f 900000 sched-entry S 0x80 100000 flags 0x2
Unable to handle kernel paging request at virtual address ffff800009551a08
Internal error: Oops: 96000007 [#1] PREEMPT SMP
pc : enetc_setup_tc_taprio+0x170/0x47c
lr : enetc_setup_tc_taprio+0x16c/0x47c
Call trace:
enetc_setup_tc_taprio+0x170/0x47c
enetc_setup_tc+0x38/0x2dc
taprio_change+0x43c/0x970
taprio_init+0x188/0x1e0
qdisc_create+0x114/0x470
tc_modify_qdisc+0x1fc/0x6c0
rtnetlink_rcv_msg+0x12c/0x390
Split enetc_setup_tc() into separate functions for the PF and for the
VF drivers. Also remove enetc_qos.o from being included into
enetc-vf.ko, since it serves absolutely no purpose there.
Fixes: 34c6adf197 ("enetc: Configure the Time-Aware Scheduler via tc-taprio offload")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220916133209.3351399-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use GFP_ATOMIC when allocating pages out of the hotpath,
continue to use GFP_KERNEL when allocating pages during setup.
GFP_KERNEL will allow blocking which allows it to succeed
more often in a low memory enviornment but in the hotpath we do
not want to allow the allocation to block.
Fixes: 9b8dd5e5ea ("gve: DQO: Add RX path")
Signed-off-by: Shailend Chand <shailend@google.com>
Signed-off-by: Jeroen de Borst <jeroendb@google.com>
Link: https://lore.kernel.org/r/20220913000901.959546-1-jeroendb@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
