[ Upstream commit 43e7c3505e ]
mhi_alloc_controller() allocates a memory space for mhi_ctrl. When gets
some error, mhi_ctrl should be freed with mhi_free_controller(). But
when ath11k_mhi_read_addr_from_dt() fails, the function returns without
calling mhi_free_controller(), which will lead to a memory leak.
We can fix it by calling mhi_free_controller() when
ath11k_mhi_read_addr_from_dt() fails.
Signed-off-by: Jianglei Nie <niejianglei2021@163.com>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220907073704.58806-1-niejianglei2021@163.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac41c2b642 ]
When the system shuts down, SMMU driver will be stopped and
will not assist in IOVA translations. SMMU driver expects all
of its consumers to shutdown before shutting down itself.
WCN6750 being one of the consumer device should not perform any
DMA operations after the SMMU has shutdown which will otherwise
result in SMMU faults.
SMMU driver will call the shutdown() callback of all its
consumer devices and the consumers shall stop further DMA
activity after the invocation of their respective shutdown()
callbacks.
Register the shutdown() callback to the platform core for WCN6750.
Change will not impact other AHB ath11k devices.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220720134710.15523-1-quic_mpubbise@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b383e8abed ]
syzbot is reporting uninit value at ath9k_htc_rx_msg() [1], for
ioctl(USB_RAW_IOCTL_EP_WRITE) can call ath9k_hif_usb_rx_stream() with
pkt_len = 0 but ath9k_hif_usb_rx_stream() uses
__dev_alloc_skb(pkt_len + 32, GFP_ATOMIC) based on an assumption that
pkt_len is valid. As a result, ath9k_hif_usb_rx_stream() allocates skb
with uninitialized memory and ath9k_htc_rx_msg() is reading from
uninitialized memory.
Since bytes accessed by ath9k_htc_rx_msg() is not known until
ath9k_htc_rx_msg() is called, it would be difficult to check minimal valid
pkt_len at "if (pkt_len > 2 * MAX_RX_BUF_SIZE) {" line in
ath9k_hif_usb_rx_stream().
We have two choices. One is to workaround by adding __GFP_ZERO so that
ath9k_htc_rx_msg() sees 0 if pkt_len is invalid. The other is to let
ath9k_htc_rx_msg() validate pkt_len before accessing. This patch chose
the latter.
Note that I'm not sure threshold condition is correct, for I can't find
details on possible packet length used by this protocol.
Link: https://syzkaller.appspot.com/bug?extid=2ca247c2d60c7023de7f [1]
Reported-by: syzbot <syzbot+2ca247c2d60c7023de7f@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/7acfa1be-4b5c-b2ce-de43-95b0593fb3e5@I-love.SAKURA.ne.jp
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d673cb6fe6 ]
This patch try to fix the following error.
Wed Jun 1 22:19:30 2022 kern.warn kernel: [ 119.561227] ath11k c000000.wifi: peer already added vdev id 0 req, vdev id 1 present
Wed Jun 1 22:19:30 2022 kern.warn kernel: [ 119.561282] ath11k c000000.wifi: Failed to add peer: 28:c2:1f:xx:xx:xx for VDEV: 0
Wed Jun 1 22:19:30 2022 kern.warn kernel: [ 119.568053] ath11k c000000.wifi: Failed to add station: 28:c2:1f:xx:xx:xx for VDEV: 0
Wed Jun 1 22:19:31 2022 daemon.notice hostapd: wlan2: STA 28:c2:1f:xx:xx:xx IEEE 802.11: Could not add STA to kernel driver
Wed Jun 1 22:19:31 2022 daemon.notice hostapd: wlan2: STA 28:c2:1f:xx:xx:xx IEEE 802.11: did not acknowledge authentication response
Wed Jun 1 22:19:31 2022 daemon.notice hostapd: wlan1: AP-STA-DISCONNECTED 28:c2:1f:xx:xx:xx
Wed Jun 1 22:19:31 2022 daemon.info hostapd: wlan1: STA 28:c2:1f:xx:xx:xx IEEE 802.11: disassociated due to inactivity
Wed Jun 1 22:19:32 2022 daemon.info hostapd: wlan1: STA 28:c2:1f:xx:xx:xx IEEE 802.11: deauthenticated due to inactivity (timer DEAUTH/REMOVE)
To repro this:
- Have 2 Wifi with the same bssid and pass on different band (2.4 and
5GHz)
- Enable 802.11r Fast Transaction with same mobility domain
- FT Protocol: FT over the Air
From a openwrt system issue the command (with the correct mac)
ubus call hostapd.wlan1 wnm_disassoc_imminent '{"addr":"28:C2:1F:xx:xx:xx"}'
Notice the log printing the errors.
The cause of this error has been investigated and we found that this is
related to the WiFi Fast Transaction feature. We observed that this is
triggered when the router tells the device to change band. In this case
the device first auth to the other band and then the disconnect path
from the prev band is triggered.
This is problematic with the current rhash implementation since the
addrs is used as key and the logic of "adding first, delete later"
conflicts with the rhash logic.
In fact peer addition will fail since the peer is already added and with
that fixed a peer deletion will cause unitended effect by removing the
peer just added.
Current solution to this is to add additional logic to the peer delete,
make sure we are deleting the correct peer taken from the rhash
table (and fallback to the peer list) and for the peer add logic delete
the peer entry for the rhash list before adding the new one (counting as
an error only when a peer with the same vlan_id is asked to be added).
With this change, a sta can correctly transition from 2.4GHz and 5GHZ
with no drop and no error are printed.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
Fixes: 7b0c70d92a ("ath11k: Add peer rhash table support")
Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220603164559.27769-1-ansuelsmth@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 55b5ee3357 ]
The number of spatial streams used when acting as a beamformee in VHT
mode are reported by the firmware as 7 (8 sts - 1) both in IPQ6018 and
IPQ8074 which respectively have 2 and 4 sts each. So the firmware should
report 1 (2 - 1) and 3 (4 - 1).
Fix this by checking that the number of VHT beamformee sts reported by
the firmware is not greater than the number of receiving antennas - 1.
The fix is based on the same approach used in this same function for
sanitizing the number of sounding dimensions reported by the firmware.
Without this change, acting as a beamformee in VHT mode is not working
properly.
Tested-on: IPQ6018 hw1.0 AHB WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01208-QCAHKSWPL_SILICONZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Jesus Fernandez Manzano <jesus.manzano@galgus.net>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220616173947.21901-1-jesus.manzano@galgus.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a20ed60bb3 ]
It has a fail log which is ath11k_dbg in ath11k_dp_rx_process_mon_status(),
as below, it will not print when debug_mask is not set ATH11K_DBG_DATA.
ath11k_dbg(ab, ATH11K_DBG_DATA,
"failed to find the peer with peer_id %d\n",
ppdu_info.peer_id);
When run scan with station disconnected, the peer_id is 0 for case
HAL_RX_MPDU_START in ath11k_hal_rx_parse_mon_status_tlv() which called
from ath11k_dp_rx_process_mon_status(), and the peer_id of ppdu_info is
reset to 0 in the while loop, so it does not match condition of the
check "if (ppdu_info->peer_id == HAL_INVALID_PEERID" in the loop, and
then the log "failed to find the peer with peer_id 0" print after the
check in the loop, it is below call stack when debug_mask is set
ATH11K_DBG_DATA.
The reason is this commit 01d2f285e3 ("ath11k: decode HE status tlv")
add "memset(ppdu_info, 0, sizeof(struct hal_rx_mon_ppdu_info))" in
ath11k_dp_rx_process_mon_status(), but the commit does not initialize
the peer_id to HAL_INVALID_PEERID, then lead the check mis-match.
Callstack of the failed log:
[12335.689072] RIP: 0010:ath11k_dp_rx_process_mon_status+0x9ea/0x1020 [ath11k]
[12335.689157] Code: 89 ff e8 f9 10 00 00 be 01 00 00 00 4c 89 f7 e8 dc 4b 4e de 48 8b 85 38 ff ff ff c7 80 e4 07 00 00 01 00 00 00 e9 20 f8 ff ff <0f> 0b 41 0f b7 96 be 06 00 00 48 c7 c6 b8 50 44 c1 4c 89 ff e8 fd
[12335.689180] RSP: 0018:ffffb874001a4ca0 EFLAGS: 00010246
[12335.689210] RAX: 0000000000000000 RBX: ffff995642cbd100 RCX: 0000000000000000
[12335.689229] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff99564212cd18
[12335.689248] RBP: ffffb874001a4dc0 R08: 0000000000000001 R09: 0000000000000000
[12335.689268] R10: 0000000000000220 R11: ffffb874001a48e8 R12: ffff995642473d40
[12335.689286] R13: ffff99564212c5b8 R14: ffff9956424736a0 R15: ffff995642120000
[12335.689303] FS: 0000000000000000(0000) GS:ffff995739000000(0000) knlGS:0000000000000000
[12335.689323] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[12335.689341] CR2: 00007f43c5d5e039 CR3: 000000011c012005 CR4: 00000000000606e0
[12335.689360] Call Trace:
[12335.689377] <IRQ>
[12335.689418] ? rcu_read_lock_held_common+0x12/0x50
[12335.689447] ? rcu_read_lock_sched_held+0x25/0x80
[12335.689471] ? rcu_read_lock_held_common+0x12/0x50
[12335.689504] ath11k_dp_rx_process_mon_rings+0x8d/0x4f0 [ath11k]
[12335.689578] ? ath11k_dp_rx_process_mon_rings+0x8d/0x4f0 [ath11k]
[12335.689653] ? lock_acquire+0xef/0x360
[12335.689681] ? rcu_read_lock_sched_held+0x25/0x80
[12335.689713] ath11k_dp_service_mon_ring+0x38/0x60 [ath11k]
[12335.689784] ? ath11k_dp_rx_process_mon_rings+0x4f0/0x4f0 [ath11k]
[12335.689860] call_timer_fn+0xb2/0x2f0
[12335.689897] ? ath11k_dp_rx_process_mon_rings+0x4f0/0x4f0 [ath11k]
[12335.689970] run_timer_softirq+0x21f/0x540
[12335.689999] ? ktime_get+0xad/0x160
[12335.690025] ? lapic_next_deadline+0x2c/0x40
[12335.690053] ? clockevents_program_event+0x82/0x100
[12335.690093] __do_softirq+0x151/0x4a8
[12335.690135] irq_exit_rcu+0xc9/0x100
[12335.690165] sysvec_apic_timer_interrupt+0xa8/0xd0
[12335.690189] </IRQ>
[12335.690204] <TASK>
[12335.690225] asm_sysvec_apic_timer_interrupt+0x12/0x20
Reset the default value to HAL_INVALID_PEERID each time after memset
of ppdu_info as well as others memset which existed in function
ath11k_dp_rx_process_mon_status(), then the failed log disappeared.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: 01d2f285e3 ("ath11k: decode HE status tlv")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220518033556.31940-1-quic_wgong@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b7b6f86149 ]
In current code STA_KEEPALIVE_ARP_RESPONSE TLV header is included only
when ARP method is used, this causes firmware always to crash when wowlan
is enabled because firmware needs it to be present no matter ARP method
is used or not.
Fix this issue by including STA_KEEPALIVE_ARP_RESPONSE TLV header by
default.
Also fix below typo:
s/WMI_TAG_STA_KEEPALVE_ARP_RESPONSE/WMI_TAG_STA_KEEPALIVE_ARP_RESPONSE/
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: 0f84a156aa ("ath11k: Handle keepalive during WoWLAN suspend and resume")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220913044358.2037-1-quic_bqiang@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3ca32308e ]
QMI message IDs for some of the QMI messages were incorrectly
defined in the original implementation. These have to be corrected
to enable cold boot support on WCN6750. These corrections are
applicable for all chipsets and will not impact them. Refactor the
code accordingly.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220720134909.15626-2-quic_mpubbise@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f020d9570a ]
When peer delete failed in a disconnect operation, use-after-free
detected by KFENCE in below log. It is because for each vdev_id and
address, it has only one struct ath10k_peer, it is allocated in
ath10k_peer_map_event(). When connected to an AP, it has more than
one HTT_T2H_MSG_TYPE_PEER_MAP reported from firmware, then the
array peer_map of struct ath10k will be set muti-elements to the
same ath10k_peer in ath10k_peer_map_event(). When peer delete failed
in ath10k_sta_state(), the ath10k_peer will be free for the 1st peer
id in array peer_map of struct ath10k, and then use-after-free happened
for the 2nd peer id because they map to the same ath10k_peer.
And clean up all peers in array peer_map for the ath10k_peer, then
user-after-free disappeared
peer map event log:
[ 306.911021] wlan0: authenticate with b0:2a:43:e6:75:0e
[ 306.957187] ath10k_pci 0000:01:00.0: mac vdev 0 peer create b0:2a:43:e6:75:0e (new sta) sta 1 / 32 peer 1 / 33
[ 306.957395] ath10k_pci 0000:01:00.0: htt peer map vdev 0 peer b0:2a:43:e6:75:0e id 246
[ 306.957404] ath10k_pci 0000:01:00.0: htt peer map vdev 0 peer b0:2a:43:e6:75:0e id 198
[ 306.986924] ath10k_pci 0000:01:00.0: htt peer map vdev 0 peer b0:2a:43:e6:75:0e id 166
peer unmap event log:
[ 435.715691] wlan0: deauthenticating from b0:2a:43:e6:75:0e by local choice (Reason: 3=DEAUTH_LEAVING)
[ 435.716802] ath10k_pci 0000:01:00.0: mac vdev 0 peer delete b0:2a:43:e6:75:0e sta ffff990e0e9c2b50 (sta gone)
[ 435.717177] ath10k_pci 0000:01:00.0: htt peer unmap vdev 0 peer b0:2a:43:e6:75:0e id 246
[ 435.717186] ath10k_pci 0000:01:00.0: htt peer unmap vdev 0 peer b0:2a:43:e6:75:0e id 198
[ 435.717193] ath10k_pci 0000:01:00.0: htt peer unmap vdev 0 peer b0:2a:43:e6:75:0e id 166
use-after-free log:
[21705.888627] wlan0: deauthenticating from d0:76:8f:82:be:75 by local choice (Reason: 3=DEAUTH_LEAVING)
[21713.799910] ath10k_pci 0000:01:00.0: failed to delete peer d0:76:8f:82:be:75 for vdev 0: -110
[21713.799925] ath10k_pci 0000:01:00.0: found sta peer d0:76:8f:82:be:75 (ptr 0000000000000000 id 102) entry on vdev 0 after it was supposedly removed
[21713.799968] ==================================================================
[21713.799991] BUG: KFENCE: use-after-free read in ath10k_sta_state+0x265/0xb8a [ath10k_core]
[21713.799991]
[21713.799997] Use-after-free read at 0x00000000abe1c75e (in kfence-#69):
[21713.800010] ath10k_sta_state+0x265/0xb8a [ath10k_core]
[21713.800041] drv_sta_state+0x115/0x677 [mac80211]
[21713.800059] __sta_info_destroy_part2+0xb1/0x133 [mac80211]
[21713.800076] __sta_info_flush+0x11d/0x162 [mac80211]
[21713.800093] ieee80211_set_disassoc+0x12d/0x2f4 [mac80211]
[21713.800110] ieee80211_mgd_deauth+0x26c/0x29b [mac80211]
[21713.800137] cfg80211_mlme_deauth+0x13f/0x1bb [cfg80211]
[21713.800153] nl80211_deauthenticate+0xf8/0x121 [cfg80211]
[21713.800161] genl_rcv_msg+0x38e/0x3be
[21713.800166] netlink_rcv_skb+0x89/0xf7
[21713.800171] genl_rcv+0x28/0x36
[21713.800176] netlink_unicast+0x179/0x24b
[21713.800181] netlink_sendmsg+0x3a0/0x40e
[21713.800187] sock_sendmsg+0x72/0x76
[21713.800192] ____sys_sendmsg+0x16d/0x1e3
[21713.800196] ___sys_sendmsg+0x95/0xd1
[21713.800200] __sys_sendmsg+0x85/0xbf
[21713.800205] do_syscall_64+0x43/0x55
[21713.800210] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[21713.800213]
[21713.800219] kfence-#69: 0x000000009149b0d5-0x000000004c0697fb, size=1064, cache=kmalloc-2k
[21713.800219]
[21713.800224] allocated by task 13 on cpu 0 at 21705.501373s:
[21713.800241] ath10k_peer_map_event+0x7e/0x154 [ath10k_core]
[21713.800254] ath10k_htt_t2h_msg_handler+0x586/0x1039 [ath10k_core]
[21713.800265] ath10k_htt_htc_t2h_msg_handler+0x12/0x28 [ath10k_core]
[21713.800277] ath10k_htc_rx_completion_handler+0x14c/0x1b5 [ath10k_core]
[21713.800283] ath10k_pci_process_rx_cb+0x195/0x1df [ath10k_pci]
[21713.800294] ath10k_ce_per_engine_service+0x55/0x74 [ath10k_core]
[21713.800305] ath10k_ce_per_engine_service_any+0x76/0x84 [ath10k_core]
[21713.800310] ath10k_pci_napi_poll+0x49/0x144 [ath10k_pci]
[21713.800316] net_rx_action+0xdc/0x361
[21713.800320] __do_softirq+0x163/0x29a
[21713.800325] asm_call_irq_on_stack+0x12/0x20
[21713.800331] do_softirq_own_stack+0x3c/0x48
[21713.800337] __irq_exit_rcu+0x9b/0x9d
[21713.800342] common_interrupt+0xc9/0x14d
[21713.800346] asm_common_interrupt+0x1e/0x40
[21713.800351] ksoftirqd_should_run+0x5/0x16
[21713.800357] smpboot_thread_fn+0x148/0x211
[21713.800362] kthread+0x150/0x15f
[21713.800367] ret_from_fork+0x22/0x30
[21713.800370]
[21713.800374] freed by task 708 on cpu 1 at 21713.799953s:
[21713.800498] ath10k_sta_state+0x2c6/0xb8a [ath10k_core]
[21713.800515] drv_sta_state+0x115/0x677 [mac80211]
[21713.800532] __sta_info_destroy_part2+0xb1/0x133 [mac80211]
[21713.800548] __sta_info_flush+0x11d/0x162 [mac80211]
[21713.800565] ieee80211_set_disassoc+0x12d/0x2f4 [mac80211]
[21713.800581] ieee80211_mgd_deauth+0x26c/0x29b [mac80211]
[21713.800598] cfg80211_mlme_deauth+0x13f/0x1bb [cfg80211]
[21713.800614] nl80211_deauthenticate+0xf8/0x121 [cfg80211]
[21713.800619] genl_rcv_msg+0x38e/0x3be
[21713.800623] netlink_rcv_skb+0x89/0xf7
[21713.800628] genl_rcv+0x28/0x36
[21713.800632] netlink_unicast+0x179/0x24b
[21713.800637] netlink_sendmsg+0x3a0/0x40e
[21713.800642] sock_sendmsg+0x72/0x76
[21713.800646] ____sys_sendmsg+0x16d/0x1e3
[21713.800651] ___sys_sendmsg+0x95/0xd1
[21713.800655] __sys_sendmsg+0x85/0xbf
[21713.800659] do_syscall_64+0x43/0x55
[21713.800663] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00288-QCARMSWPZ-1
Fixes: d0eeafad11 ("ath10k: Clean up peer when sta goes away.")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220801141930.16794-1-quic_wgong@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d81bbb684c ]
Currently host can send two WMI commands at once. There is possibility to
cause SMMU issues or corruption, if host wants to initiate 2 DMA
transfers, it is possible when copy complete interrupt for first DMA
reaches host, CE has already updated SRRI (Source ring read index) for
both DMA transfers and is in the middle of 2nd DMA. Host uses SRRI
(Source ring read index) to interpret how many DMA’s have been completed
and tries to unmap/free both the DMA entries. Hence now it is limiting to
one.Because CE is still in the middle of 2nd DMA which can cause these
issues when handling two DMA transfers.
This change will not impact other targets, as it is only for WCN3990.
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1
Signed-off-by: Youghandhar Chintala <quic_youghand@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220801134941.15216-1-quic_youghand@quicinc.com
Stable-dep-of: f020d9570a ("wifi: ath10k: add peer map clean up for peer delete in ath10k_sta_state()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
Pull tracing updates from Steven Rostedt:
- Runtime verification infrastructure
This is the biggest change here. It introduces the runtime
verification that is necessary for running Linux on safety critical
systems.
It allows for deterministic automata models to be inserted into the
kernel that will attach to tracepoints, where the information on
these tracepoints will move the model from state to state.
If a state is encountered that does not belong to the model, it will
then activate a given reactor, that could just inform the user or
even panic the kernel (for which safety critical systems will detect
and can recover from).
- Two monitor models are also added: Wakeup In Preemptive (WIP - not to
be confused with "work in progress"), and Wakeup While Not Running
(WWNR).
- Added __vstring() helper to the TRACE_EVENT() macro to replace
several vsnprintf() usages that were all doing it wrong.
- eprobes now can have their event autogenerated when the event name is
left off.
- The rest is various cleanups and fixes.
* tag 'trace-v6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (50 commits)
rv: Unlock on error path in rv_unregister_reactor()
tracing: Use alignof__(struct {type b;}) instead of offsetof()
tracing/eprobe: Show syntax error logs in error_log file
scripts/tracing: Fix typo 'the the' in comment
tracepoints: It is CONFIG_TRACEPOINTS not CONFIG_TRACEPOINT
tracing: Use free_trace_buffer() in allocate_trace_buffers()
tracing: Use a struct alignof to determine trace event field alignment
rv/reactor: Add the panic reactor
rv/reactor: Add the printk reactor
rv/monitor: Add the wwnr monitor
rv/monitor: Add the wip monitor
rv/monitor: Add the wip monitor skeleton created by dot2k
Documentation/rv: Add deterministic automata instrumentation documentation
Documentation/rv: Add deterministic automata monitor synthesis documentation
tools/rv: Add dot2k
Documentation/rv: Add deterministic automaton documentation
tools/rv: Add dot2c
Documentation/rv: Add a basic documentation
rv/include: Add instrumentation helper functions
rv/include: Add deterministic automata monitor definition via C macros
...
The naming of the get/set/clear firmware feature capability bits doesn't
really follow the established namespace pattern of
wcn36xx_logicalblock_do_something();
The feature bits are accessed by smd.c and main.c. It would be nice to
display the found feature bits in debugfs. To do so though we should tidy
up the namespace a bit.
Move the firmware feature exchange API to its own file - firmware.c giving
us the opportunity to functionally decompose other firmware related
accessors as appropriate in future.
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220727161655.2286867-3-bryan.odonoghue@linaro.org
Commit 7a4836560a changes simple_write_to_buffer() with memdup_user()
but it forgets to change the value to be returned that came from
simple_write_to_buffer() call. It results in the following warning:
warning: variable 'rc' is uninitialized when used here [-Wuninitialized]
return rc;
^~
Remove rc variable and just return the passed in length if the
memdup_user() succeeds.
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 7a4836560a ("wifi: wil6210: debugfs: fix info leak in wil_write_file_wmi()")
Fixes: ff974e4083 ("wil6210: debugfs interface to send raw WMI command")
Signed-off-by: Ammar Faizi <ammarfaizi2@gnuweeb.org>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220724202452.61846-1-ammar.faizi@intel.com
Commit 56c8ccf331 ("ath11k: Add register access logic for WCN6750")
regressed QCN9074. With the above mentioned commit, writes are failing
for some registers on QCN9074 although the device seems to work
normally.
ath11k_pci 0000:03:00.0: failed to set pcie link register0x01e0e0a8: 0xffffffff != 0x00000010
ath11k_pci 0000:03:00.0: failed to set sysclk: -110
PCIe devices in ath11k (QCA6390, WCN6855, QCN9074, WCN6750) use window
concept for register accesses. There are two schemes, dynamic & static
window.
In dynamic window scheme, a single window(region in the BAR) is mapped
either to CE or DP register windows at any give time. QCA6390 & WCN6855
follow this scheme for register accesses.
In static window scheme, CE & DP register windows are statically mapped
to separate regions with in the BAR so that there is no switching of
register windows between CE & DP register accesses. QCN9074 & WCN6750
follow this scheme although the window start offsets are different for
QCN9074 & WCN6750.
QCN9074 uses 3rd & 2nd window for DP & CE register accesses respectively
whereas WCN6750 uses 1st & 2nd window for DP & CE. In QCN9074, along with
2nd & 3rd windows, 1st window is also used for certain configurations
which commit 56c8ccf331 ("ath11k: Add register access logic for WCN6750")
did not account for and hence the regression.
Fix this by going back to the original way of accessing the registers on
QCN9074. Since this diverges from WCN6750 way of accessing registers, it
is required to register window_read32/window_write32() pci_ops for WCN6750.
We can also get rid of dp_window_idx & ce_window_idx members in hw_params,
so remove them.
Also add a new API ath11k_pcic_register_pci_ops() for registering pci_ops
to the ath11k core. This API checks for mandatory pci_ops() and reports
error if those are missing. Also initialize unused pci_ops to NULL.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1
Fixes: 56c8ccf331 ("ath11k: Add register access logic for WCN6750")
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Tested-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220608062954.27792-1-quic_mpubbise@quicinc.com
The simple_write_to_buffer() function will succeed if even a single
byte is initialized. However, we need to initialize the whole buffer
to prevent information leaks. Just use memdup_user().
Fixes: ff974e4083 ("wil6210: debugfs interface to send raw WMI command")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/Ysg14NdKAZF/hcNG@kili
Since mac80211 already has a protected pointer to link_conf,
pass it to the driver to avoid additional RCU locking.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This really shouldn't be in a per-link config, we don't want
to let anyone control it that way (if anything, link powersave
could be forced through APIs to activate/deactivate a link),
and we don't support powersave in software with devices that
can do MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johannes Berg says:
====================
A fairly large set of updates for next, highlights:
ath10k
* ethernet frame format support
rtw89
* TDLS support
cfg80211/mac80211
* airtime fairness fixes
* EHT support continued, especially in AP mode
* initial (and still major) rework for multi-link
operation (MLO) from 802.11be/wifi 7
As usual, also many small updates/cleanups/fixes/etc.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Most drivers use "skb_transport_offset(skb) + tcp_hdrlen(skb)"
to compute headers length for a TCP packet, but others
use more convoluted (but equivalent) ways.
Add skb_tcp_all_headers() and skb_inner_tcp_all_headers()
helpers to harmonize this a bit.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MLO links used for connection with an MLD AP are decided by the
driver in case of SME offloaded to driver.
Add support for the drivers to indicate the information of links used
for MLO connection in connect and roam callbacks, update the connected
links information in wdev from connect/roam result sent by driver.
Also, send the connected links information to userspace.
Add a netlink flag attribute to indicate that userspace supports
handling of MLO connection. Drivers must not do MLO connection when this
flag is not set. This is to maintain backwards compatibility with older
supplicant versions which doesn't have support for MLO connection.
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pass the link id through to the get_beacon and return
the beacon for a specific link id.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make the channel context code MLO aware, along with some
functions that it uses, so that the chan.c file is now
MLD-clean and no longer uses deflink/bss_conf/etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Split the bss_info_changed method to vif_cfg_changed and
link_info_changed, with the latter getting a link ID.
Also change the 'changed' parameter to u64 already, we
know we need that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We'll use bss_conf for per-link configuration later, so
move out all the non-link-specific data out into a new
struct ieee80211_vif_cfg used in the vif.
Some adjustments were done with the following spatch:
@@
expression sdata;
struct ieee80211_vif *vifp;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
(
-sdata->vif.bss_conf.var
+sdata->vif.cfg.var
|
-vifp->bss_conf.var
+vifp->cfg.var
)
@bss_conf@
struct ieee80211_bss_conf *bss_conf;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
-bss_conf->var
+vif_cfg->var
(though more manual fixups were needed, e.g. replacing
"vif_cfg->" by "vif->cfg." in many files.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To add MLD, reuse the bss_conf structure later for per-link
information, so move some things into it that are per link.
Most transformations were done with the following spatch:
@@
expression sdata;
identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color };
@@
-sdata->vif.var
+sdata->vif.bss_conf.var
@@
struct ieee80211_vif *vif;
identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color };
@@
-vif->var
+vif->bss_conf.var
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support multi-link operation with multiple links,
start adding some APIs. The notable addition here is to have
the link ID in a new nl80211 attribute, that will be used to
differentiate the links in many nl80211 operations.
So far, this patch adds the netlink NL80211_ATTR_MLO_LINK_ID
attribute (as well as the NL80211_ATTR_MLO_LINKS attribute)
and plugs it through the system in some places, checking the
validity etc. along with other infrastructure needed for it.
For now, I've decided to include only the over-the-air link
ID in the API. I know we discussed that we eventually need to
have to have other ways of identifying a link, but for local
AP mode and auth/assoc commands as well as set_key etc. we'll
use the OTA ID.
Also included in this patch is some refactoring of the data
structures in struct wireless_dev, splitting for the first
time the data into type dependent pieces, to make reasoning
about these things easier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
I've changed *STAT_* macros a bit in previous patch and I seems like
they become really unreadable. Align these macros definitions to make
code cleaner and fix folllowing checkpatch warning
ERROR: Macros with complex values should be enclosed in parentheses
Also, statistics macros now accept an hif_dev as argument, since
macros that depend on having a local variable with a magic name
don't abide by the coding style.
No functional change
Suggested-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/ebb2306d06a496cd1b032155ae52fdc5fa8cc2c5.1655145743.git.paskripkin@gmail.com
