[ Upstream commit a1e07ba89d ]
[Why]
The input color space for the plane was previously ignored even if it
was set.
If a limited range YUV format was given to DC then the
wrong color transformation matrix was being used since DC assumed that
it was full range instead.
[How]
Respect the given color_space format for the plane if it isn't
COLOR_SPACE_UNKNOWN. Otherwise, use the implicit default since DM
didn't specify.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15ae3b28f8 ]
[Why]
If link is already enabled at a different rate (for example 5.4 Gbps)
then calling VBIOS command table to switch to a new rate
(for example 2.7 Gbps) will not take effect.
This can lead to link training failure to occur.
[How]
If the requested link rate is different than the current link rate,
the link must be disabled in order to re-enable at the new
link rate.
In today's logic it is currently only impacting eDP since DP
connection types will always disable the link during display
detection, when initial link verification occurs.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4bc46da4a3 ]
[Why]
Seamless boot tries to reuse planes that were enabled for the first
commit applied.
In the case where Raven is booting with two monitors connected and the
first commit contains two streams the screen corruption would occur
because the second stream was trying to re-use a tg and plane that
weren't previously enabled.
The state on the first commit looks something like the following:
TG0: enabled=1
TG1: enabled=0
TG2: enabled=0
TG3: enabled=0
New state: pipe=0, stream=0, plane=0, new_tg=0
New state: pipe=1, stream=1, plane=1, new_tg=1
New state: pipe=2, stream=NULL, plane=NULL, new_tg=NULL
New state: pipe=3, stream=NULL, plane=NULL, new_tg=NULL
Only one plane/tg is setup before we enter accelerated mode so
we really want to disabling everything but that first plane.
[How]
Check if the stream is not NULL and if the tg is enabled before
deciding whether to skip the plane disable.
Also ensure we're also disabling on the current state's pipe_ctx so
we don't overwrite the fields in the new pending state.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dcf1a98867 ]
[Why]
AUX arbitration occurs between SW and FW components.
When AUX acquire fails, it causes engine->ddc to be NULL,
which leads to an exception when we try to release the AUX
engine.
[How]
When AUX engine acquire fails, it should return from the
function without trying to continue the operation.
The upper level will determine if it wants to retry.
i.e. dce_aux_transfer_with_retries will be used and retry.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 162f807858 ]
[Why]
used to be unable to run 4:2:0 if using a dongle because 4k60 bandwidth
exceeded dongle caps
[How]
half pixel clock during comparison to dongle cap. *Could get stuck on black
screen on monitor that don't support 420 but will be selecting 420 as
preferred mode*
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Aidan Wood <Aidan.Wood@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6bddf6c67 ]
[why]
Stream update will adjust both info packets and stream params,
need to make sure all things are applied togather.
[how]
add pipe lock during stream update
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66acd4418d ]
[Why]
In certain cases we do link training when we don't have a backend.
[How]
In dc_link_set_preferred_link_settings(), store preferred link settings
first and then verify that the link is DP and the link stream's backend is
enabled. If either is false, then we will not do any link retraining.
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6752bea8b0 ]
[Why]
The actual position for the cursor on the screen is essentially:
x_out = x - x_plane - x_hotspot
y_out = y - y_plane - y_hotspot
The register values for cursor position and cursor hotspot need to be
greater than zero when programmed, but we also need to subtract off
the plane position to display the cursor at the correct position.
Since we don't want x or y to be less than zero, we add the plane
position as a positive value to x_hotspot or y_hotspot. However, what
this doesn't take into account is that the hotspot registers are limited
by the maximum cursor size.
On DCN10 the cursor hotspot regitsers are masked to 0xFF, so they have
a maximum value of 0-255. Values greater this will wrap, causing the
cursor to display in the wrong position.
In practice this means that for sufficiently large plane positions, the
cursor will be drawn twice on the screen, and can cause screen flashes
or p-state WARNS depending on what the wrapped value is.
So we need a way to remove the value from x_plane and y_plane without
exceeding the maximum cursor size.
[How]
Subtract as much as x_plane/y_plane as possible from x and y and place
the remainder in the cursor hotspot register.
The value for x_hotspot and y_hotspot can still wrap around but it
won't happen in a case where the cursor is actually enabled.
The cursor plane needs to intersect at least one pixel of the plane's
rectangle to be enabled, so the cursor position + hotspot provided by
userspace must always be strictly less than the maximum cursor size for
the cursor to actually be enabled.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e49f69363a ]
[why]
The existing calculation uses a wrong formula to
calculate bandwidth from timing.
[how]
Expose the existing proper function that calculates the bandwidth,
so dc_link can use it to calculate timing bandwidth correctly.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[Why]
On some compositors, with two monitors attached, VT terminal
switch can cause a graphical issue by the following means:
There are two streams, one for each monitor. Each stream has one
plane
current state:
M1:S1->P1
M2:S2->P2
The user calls for a terminal switch and a commit is made to
change both planes to linear swizzle mode. In atomic check,
a new dc_state is constructed with new planes on each stream
new state:
M1:S1->P3
M2:S2->P4
In commit tail, each stream is committed, one at a time. The first
stream (S1) updates properly, triggerring a full update and replacing
the state
current state:
M1:S1->P3
M2:S2->P4
The update for S2 comes in, but dc detects that there is no difference
between the stream and plane in the new and current states, and so
triggers a fast update. The fast update does not program swizzle,
so the second monitor is corrupted
[How]
Add a flag to dc_plane_state that forces full updates
When a stream undergoes a full update, set this flag on all changed
planes, then clear it on the current stream
Subsequent streams will get full updates as a result
Signed-off-by: David Francis <David.Francis@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
AUX takes longer to reply when using active DP-DVI dongle on some asics
resulting in up to 2000+ us edid read (timeout).
[How]
1. Adjust AUX poll to match spec
2. Extend the SW timeout. This does not affect normal
operation since we exit the loop as soon as AUX acks.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If the cursor pos passed from DM is less than the plane_state->dst_rect
top left corner then the unsigned cursor pos wraps around to a large
positive number since cursor pos is a u32.
There was an attempt to guard against this in hubp1_cursor_set_position
by checking the src_x_offset and src_y_offset and offseting the
cursor hotspot within hubp1_cursor_set_position.
However, the cursor position itself is still being programmed
incorrectly as a large value.
This manifests itself visually as the cursor disappearing or containing
strange artifacts near the middle of the screen on raven.
[How]
Don't subtract the destination rect top left corner from the pos but
add it to the hotspot instead. This happens before the pos gets
passed into hubp1_cursor_set_position.
This achieves the same result but avoids the subtraction wrap around.
With this fix the original cursor programming logic can be used again.
v2: add hunk that got dropped accidently when this patch was originally
committed. (Alex)
Fixes: 0921c41e19 ("drm/amd/display: Fix negative cursor pos programming")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Murton Liu <Murton.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
VBIOS will not post pixel rate > 340MHz.
If driver set pixel rate > 340MHz and do restart bottom, VBIOS can't
post HDMI monitor due to monitor is stay in HDMI2.0 state.
[How]
Program Scrambling_Enable and TMDS_Bit_Clock_Ratio when disable stream.
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Powerplay functions called from dm_pp_* functions tend to do a
mutex_lock which isn't safe to do inside a kernel_fpu_begin/end block as
those will disable/enable preemption.
Rearrange the dm_pp_get_clock_levels_by_type_with_voltage calls to make
sure they happen outside of kernel_fpu_begin/end.
Cc: stable@vger.kernel.org
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a really hairy resolution involving amdgpu fixes, that I'd rather confirm here.
Also some misc fixes are landed by me, but the pr has them as well.
Signed-off-by: Dave Airlie <airlied@redhat.com>
[Why]
For MST, link not disabled until all streams disabled
[How]
Add check for stream_count before setting link_active = false for MST
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fixes for 5.1:
amdgpu:
- Fix missing fw declaration after dropping old CI DPM code
- Fix debugfs access to registers beyond the MMIO bar size
- Fix context priority handling
- Add missing license on some new files
- Various cleanups and bug fixes
radeon:
- Fix missing break in CS parser for evergreen
- Various cleanups and bug fixes
sched:
- Fix entities with 0 run queues
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190221214134.3308-1-alexander.deucher@amd.com
[Why]
When a dce80 asic was suspended, the clocks were not set to 0.
Upon resume, the new clock was compared to the existing clock,
they were found to be the same, and so the clock was not set.
This resulted in a blackscreen.
[How]
In atomic commit, check to see if there are any active pipes.
If no, set clocks to 0
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
If the cursor pos passed from DM is less than the plane_state->dst_rect
top left corner then the unsigned cursor pos wraps around to a large
positive number since cursor pos is a u32.
There was an attempt to guard against this in hubp1_cursor_set_position
by checking the src_x_offset and src_y_offset and offseting the
cursor hotspot within hubp1_cursor_set_position.
However, the cursor position itself is still being programmed
incorrectly as a large value.
This manifests itself visually as the cursor disappearing or containing
strange artifacts near the middle of the screen on raven.
[How]
Don't subtract the destination rect top left corner from the pos but
add it to the hotspot instead. This happens before the pos gets
passed into hubp1_cursor_set_position.
This achieves the same result but avoids the subtraction wrap around.
With this fix the original cursor programming logic can be used again.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Murton Liu <Murton.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current periodic interrupt start point calc in optc
is not clear.
[How]
1. DM convert delta time to lines number and dc will calculate the
start position as per lines number and interrupt type.
2. hwss calculates the start point as per line offset.
3. optc programs vertical interrupts register as per start point
and interrupt source.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The stream->mode_changed flag can persist in the following sequence
of atomic commits:
Commit 1:
Enable CRTC0 (mode_changed = true), Enable CRTC1 (mode_changed = true)
Commit 2:
Disable CRTC1 (mode_changed = false)
In this sequence we want to keep the exiting CRTC0 but it's not in the
atomic state for the commit since it hasn't been modified. In this case
the stream->mode_changed flag persists as true and we don't re-program
the planes for the existing stream.
[How]
The flag needs to be cleared and it makes the most sense to do it within
DC after the state has been committed. Nothing following dc_commit_state
should think that the stream's mode has changed.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously, a change removed code that would send a pipe set command
to dmcu each time the backlight was set, as it was thought to be
superfluous. However, it is possible for the backlight to be set
before a valid pipe has been set, which causes DMCU to hang after a
DPMS restore on some systems.
[How]
Send a pipe set command to DMCU prior to setting the backlight.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Certain tests fail after a fresh reboot. This is caused by writing to
registers prior to ungating the stream we're trying to program.
[How]
Make sure the stream is ungated before writing to its registers.
This also enables power-gating plane resources before init_hw
initializes them.
Additionally, this does some refactoring to move gating/ungating
from enable/disable_plane functions to where stream resources are
enabled/disabled.
Signed-off-by: Gary Kattan <gary.kattan@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want boot to desktop to be seamless
[How]
During init pipes, avoid touching the pipes where GOP has already
enabled the HW to the state we want.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When stream is blanked, pipe set command is sent to dmcu to notify it
that the abm pipe is disabled. When stream is unblanked, no notification is
made to dmcu that the abm pipe has been enabled, resulting in abm not
being enabled in the firmware.
[How]
When stream is unblanked, send a pipe set command to dmcu.
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The visual corruption due to low display clock value.
Observed on Carrizo 4K@60Hz.
[How]
There was earlier patch for dce_update_clocks:
Adding +15% workaround also to to dce11_update_clocks
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Pipe related init is possible to optimized if we know what we
intend to program, and if we can determine it matches what is
already programmed for the pipe.
[How]
First step is to isolate the pipe related init code
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Keep enable_stream_timing programming only
timing related stuff.
[How]
Move DRR and static screen mask programming from
enable_stream_timing to outside in
apply_single_controller_ctx_to_hw
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If we determine the stream we are trying to commit
matches HW, we want to try to optimize.
[How]
Try to acquire the HW resources that are already enabled
and optimize.
Also skip backend reprogramming
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need to understand whether link is active aside from stream state.
This could be used to check what links are enabled by GOP.
[How]
Store link_active state in link status and initialize it by checking
if the DIG is enabled.
Keep it updated on every link enable and disable
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
More clearly isolate the code that is involved in programming of
vupdate interrupt
[How]
Add function for programming of vupdate interrupt.
Call it after timing is programmed.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need to figure out whether a timing we want to commit matches
something that GOP already programmed, in which case
we can decide to some optimizations
[How]
1. Add way to check for DIG FE
2. Add way to check for matching OTG timing
3. Add way to check for matching pixel clock (if possible)
- Currently only support DP for pixel clock, since it is easy to calc
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When moving mouse onto or off of pip plane,
screen would flash briefly due to garbage negative
pos values being programmed for cursor.
Also, text flashes due to PIP flips taking too long.
[How]
When negative pos value seen, default to 0 and adjust by modifying cursor hotspot.
For flip issue, only do post update when optimize required vs all the time.
Signed-off-by: Murton Liu <murton.liu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Sivapiriyan Kumarasamy <Sivapiriyan.Kumarasamy@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Current implementation that maps link_rate_set value to
actual link rate is incorrect.
[How]
Fix this implementation, such that link_rate_set indexes into
the supported_link_rate table.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
VM_helper needs to be intialized with the dc struct in order to fix
an unallocated memory issue. System aperture settings should be
initialized to 0 and guarded with a check to make sure vm_config
is valid.
[How]
Allocate and free memory for vm_helper with other dc members.
Check whether the vm_config valid bit is set before initializing
aperture settings.
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Bandwidth calculation formulas currently do not take Stereo 3D + Stutter
properly into account. Disable stutter feature when we detect a Stereo
3D mode as a temporary workaround.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Martin Leung <Martin.Leung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This fixes an mpc programming error for the following sequence of
atomic commits when pipe split is enabled:
Commit 1: CRTC0 (plane 4, plane 3)
Pipe 0: old_plane_state = A0, new_plane_state = A1, new_tg = T0
Pipe 1: old_plane_state = B0, new_plane_state = B1, new_tg = T0
Pipe 2: old_plane_state = A0, new_plane_state = A1, new_tg = T0
Pipe 3: old_plane_state = B0, new_plane_state = B1, new_tg = T0
Commit 2: CRTC0 (plane 3), CRTC1 (plane 2)
Pipe 0: old_plane_state = A1, new_plane_state = A2, new_tg = T0
Pipe 1: old_plane_state = B1, new_plane_state = B2, new_tg = T1
Pipe 2: old_plane_state = A1, new_plane_state = NULL, new_tg = NULL
Pipe 3: old_plane_state = B1, new_plane_state = NULL, new_tg = NULL
In the second commit the assertion for mpcc in use is hit because
mpcc disconnect never occurs for pipe 1. This is because the stream
changes for pipe 1 and the opp_list is empty.
This sequence occurs when running the
"igt@kms_plane_multiple@atomic-pipe-A-tiling-none" test with two
displays connected.
[How]
Expand the reset condition to include:
"old_pipe_ctx->stream_res.tg != new_pipe_ctx->stream_res.tg"
...but only when the plane state is non-NULL for both old and new.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
