commit 6f4870753f upstream.
The proper name for the property, which assign given device to IOMMU is
'iommus', not 'iommu'. Fix incorrect name and let all GScaler devices
to be properly handled when IOMMU support is enabled.
Reported-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: 6cbfdd73a9 ("ARM: dts: add sysmmu nodes for exynos5250")
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0629a01920 upstream.
Fix that USB initialization fails as below runtime log is present during
booting on bananapi-r2 board by adding missing regulators the USB device
requires. Current regulators USB device uses are being updated with the
correct ones to reflect real configurations which are all from fixed
regulators rather than MT6323 one's output.
xhci-mtk 1a1c0000.usb: 1a1c0000.usb supply vbus not found, using dummy regulator
xhci-mtk 1a240000.usb: 1a240000.usb supply vbus not found, using dummy regulator
Cc: stable@vger.kernel.org
Fixes: f4ff257cd1 ("arm: dts: mt7623: add support for Bananapi R2 (BPI-R2) board")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
[mb: update kernel log in commit message]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c5a88cd2e1 upstream.
This fixes the battery voltage monitoring gpio-hog settings.
When the gpio is low, it turns off the battery voltage to the ADC chip.
However, this needs to be on all of the time so that we can monitor
battery voltage.
Also, there was a typo that prevented pinmuxing from working correctly.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d5c7b4d5ac ]
Commit a22950c888 (mmc: sdhci-of-esdhc: add quirk
SDHCI_QUIRK_BROKEN_TIMEOUT_VAL for ls1021a) added logic to the driver to
enable the broken timeout val quirk for ls1021a, but did not add the
corresponding compatible string to the device tree, so it didn't really
have any effect. Fix that.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 70b8d21496 upstream.
This patch fixes a bootproblem with the Bananapi M2 board. Since there
are some regulators missing we add them right now. Those values come
from the schematic, below you can find a small overview:
* reg_aldo1: 3,3V, powers the wifi
* reg_aldo2: 2,5V, powers the IO of the RTL8211E
* reg_aldo3: 3,3V, powers the audio
* reg_dldo1: 3,0V, powers the RTL8211E
* reg_dldo2: 2,8V, powers the analog part of the csi
* reg_dldo3: 3,3V, powers misc
* reg_eldo1: 1,8V, powers the csi
* reg_ldo_io1:1,8V, powers the gpio
* reg_dc5ldo: needs to be always on
This patch updates also the vmmc-supply properties on the mmc0 and mmc2
node to use the allready existent regulators.
We can now remove the sunxi-common-regulators.dtsi include since we
don't need it anymore.
Fixes: 7daa213700 ("ARM: dts: sunxi: Add regulators for Sinovoip BPI-M2")
Cc: <stable@vger.kernel.org>
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b23af6ad8d upstream.
The eldoin is supplied from the dcdc1 regulator. The N_VBUSEN pin is
connected to an external power regulator (SY6280AAC).
With this commit we update the pmic binding properties to support
those features.
Fixes: 7daa213700 ("ARM: dts: sunxi: Add regulators for Sinovoip BPI-M2")
Cc: <stable@vger.kernel.org>
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7be4b5dc7f ]
The correct DT property for specifying a GPIO used for reset
is "reset-gpios", fix this here.
Fixes: 14e3e295b2 ("ARM: dts: omap3-n900: Add TLV320AIC3X support")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e153db03c6 ]
The correct DT property for specifying a GPIO used for reset
is "reset-gpios", fix this here.
Fixes: 4341881d05 ("ARM: dts: Add devicetree for Gumstix Pepper board")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 74402055a2 upstream.
The pinmuxing was missing for I2C1 which was causing intermittent issues
with the PMIC which is connected to I2C1. The bootloader did not quite
configure the I2C1 either, so when running at 2.6MHz, it was generating
errors at time.
This correctly sets the I2C1 pinmuxing so it can operate at 2.6MHz
Fixes: 687c276761 ("ARM: dts: Add minimal support for LogicPD Torpedo
DM3730 devkit")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 84c7efd607 upstream.
The pinmuxing was missing for I2C1 which was causing intermittent issues
with the PMIC which is connected to I2C1. The bootloader did not quite
configure the I2C1 either, so when running at 2.6MHz, it was generating
errors at times.
This correctly sets the I2C1 pinmuxing so it can operate at 2.6MHz
Fixes: ab8dd3aed0 ("ARM: DTS: Add minimal Support for Logic PD DM3730
SOM-LV")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5ce0bad4cc upstream.
Rockchip recommends to run the CPU cores only with operations points of
1.6 GHz or lower.
Removed the cpu0 node with too high operation points and use the default
values instead.
Fixes: 903d31e346 ("ARM: dts: rockchip: Add support for phyCORE-RK3288 SoM")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 506e8a9126 ]
dtc warns about two 'clocks' properties that have an extraneous '1'
at the end:
arch/arm/boot/dts/ls1021a-qds.dtb: Warning (clocks_property): arch/arm/boot/dts/ls1021a-twr.dtb: Warning (clocks_property): Property 'clocks', cell 1 is not a phandle reference in /soc/i2c@2180000/mux@77/i2c@4/sgtl5000@2a
arch/arm/boot/dts/ls1021a-qds.dtb: Warning (clocks_property): Missing property '#clock-cells' in node /soc/interrupt-controller@1400000 or bad phandle (referred from /soc/i2c@2180000/mux@77/i2c@4/sgtl5000@2a:clocks[1])
Property 'clocks', cell 1 is not a phandle reference in /soc/i2c@2190000/sgtl5000@a
arch/arm/boot/dts/ls1021a-twr.dtb: Warning (clocks_property): Missing property '#clock-cells' in node /soc/interrupt-controller@1400000 or bad phandle (referred from /soc/i2c@2190000/sgtl5000@a:clocks[1])
The clocks that get referenced here are fixed-rate, so they do not
take any argument, and dtc interprets the next cell as a phandle, which
is invalid.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d364b038bc ]
Looks like the interrupt property is missing the controller and level
information causing:
Warning (interrupts_property): interrupts size is (4), expected multiple
of 12 in /ocp/elm@48078000
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cd7594ac32 ]
The pin assignment for the wl127x interrupt was incorrect. I am
not sure how this every worked. This also eliminates a conflict with
the SMC911x ethernet driver and properly moves pinmuxes for the
related gpio to omap3_pmx_wkup from omap3_pmx_core.
Fixes: ab8dd3aed0 ("ARM: DTS: Add minimal Support for Logic PD
DM3730 SOM-LV")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3c18bbf3d1 ]
This patch fixes and issue where the NAND and GPMC based ethernet
controller stopped working. This also updates the GPMC settings
to be consistent with the Logic PD Torpedo development from the
commit listed above.
Fixes: 44e4716499 ("ARM: dts: omap3: Fix NAND device nodes")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cf87634c8b ]
There's been a reproducable USB OHCI/EHCI cpuidle related hang on omap4
for a while that happens after about 20 - 40 minutes on an idle system
with some data feeding device being connected, like a USB GPS device or
a cellular modem.
This issue happens in cpuidle states C2 and C3 and does not happen if
cpuidle is limited to C1 state only. The symptoms are that the whole
system hangs and never wakes up from idle, and if a watchdog is
configured the system reboots after a while.
Turns out that OHCI/EHCI devices on omap4 are trying to use the GIC
interrupt controller directly as a parent instead of the WUGEN. We
need to pass the interrupts through WUGEN to GIC to provide the wakeup
events for the processor.
Let's fix the issue by removing the gic interrupt-parent and use the
default interrupt-parent wakeupgen instead. Note that omap5.dtsi had
this already fixes earlier by commit 7136d457f3 ("ARM: omap: convert
wakeupgen to stacked domains") but we somehow missed omap4 at that
point.
Fixes: 7136d457f3 ("ARM: omap: convert wakeupgen to stacked domains")
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 586b2a4bef upstream.
The EB MP board probably has a character LCD but the board manual does
not really state which IRQ it has assigned to this device. The invalid
assignment was a mistake by me during submission of the DTSI where I was
looking for the reference, didn't find it and didn't fill it in.
Delete this for now: it can probably be fixed but that requires access
to the actual board for some trial-and-error experiments.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5c1037196b upstream.
The ohci-hcd node has an interrupt number but no interrupt-parent,
leading to a warning with current dtc versions:
arch/arm/boot/dts/s5pv210-aquila.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-goni.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-smdkc110.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-smdkv210.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
arch/arm/boot/dts/s5pv210-torbreck.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/ohci@ec300000
As seen from the related exynos dts files, the ohci and ehci controllers
always share one interrupt number, and the number is the same here as
well, so setting the same interrupt-parent is the reasonable solution
here.
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5628a8ca14 upstream.
According to the comment added to exynos_dt_pmu_match[] in commit
8b283c0254 ("ARM: exynos4/5: convert pmu wakeup to stacked domains"),
the RTC is not able to wake up the system through the PMU on Exynos5410,
unlike Exynos5420.
However, when the RTC DT node got added, it was a straight copy of
the Exynos5420 node, which now causes a warning from dtc.
This removes the incorrect interrupt-parent, which should get the
interrupt working and avoid the warning.
Fixes: e1e146b1b0 ("ARM: dts: exynos: Add RTC and I2C to Exynos5410")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8975cb1b8 upstream.
This fixes the following warning by also sending the flags argument for
gpio controllers:
Property 'cs-gpios', cell 6 is not a phandle reference in
/ahb/apb/spi@e0100000
Fixes: 8113ba917d ("ARM: SPEAr: DT: Update device nodes")
Cc: stable@vger.kernel.org # v3.8+
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cdd1040991 upstream.
The "dmas" cells for the designware DMA controller need to have only 3
properties apart from the phandle: request line, src master and
destination master. But the commit 6e8887f60f updated it incorrectly
while moving from platform code to DT. Fix it.
Cc: stable@vger.kernel.org # v3.10+
Fixes: 6e8887f60f ("ARM: SPEAr13xx: Pass generic DW DMAC platform data from DT")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e8bfa04224 upstream.
The clcd device is lacking an interrupt-parent property, which makes
the interrupt unusable and shows up as a warning with the latest
dtc version:
arch/arm/boot/dts/ste-nomadik-s8815.dtb: Warning (interrupts_property): Missing interrupt-parent for /amba/clcd@10120000
arch/arm/boot/dts/ste-nomadik-nhk15.dtb: Warning (interrupts_property): Missing interrupt-parent for /amba/clcd@10120000
I looked up the old board files and found that this interrupt has
the same irqchip as all the other on-chip device, it just needs one
extra line.
Fixes: 17470b7da1 ("ARM: dts: add the CLCD LCD display to the NHK15")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ac1f59c09 upstream.
The GPIO polarity is missing in the hdmi,hpd-gpio property, this
fixes the following DT warnings:
arch/arm/boot/dts/stih410-b2120.dtb: Warning (gpios_property): hdmi,hpd-gpio property
size (8) too small for cell size 2 in /soc/sti-display-subsystem/sti-hdmi@8d04000
arch/arm/boot/dts/stih407-b2120.dtb: Warning (gpios_property): hdmi,hpd-gpio property
size (8) too small for cell size 2 in /soc/sti-display-subsystem/sti-hdmi@8d04000
arch/arm/boot/dts/stih410-b2260.dtb: Warning (gpios_property): hdmi,hpd-gpio property
size (8) too small for cell size 2 in /soc/sti-display-subsystem/sti-hdmi@8d04000
[arnd: marked Cc:stable since this warning shows up with the latest dtc
by default, and is more likely to actually cause problems than the
other patches from this series]
Cc: stable@vger.kernel.org
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ca32e0c4bf upstream.
dtc warns about obviously incorrect GPIO numbers for the audio codec
on both lpc32xx boards:
arch/arm/boot/dts/lpc3250-phy3250.dtb: Warning (gpios_property): reset-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
arch/arm/boot/dts/lpc3250-phy3250.dtb: Warning (gpios_property): power-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
arch/arm/boot/dts/lpc3250-ea3250.dtb: Warning (gpios_property): reset-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
arch/arm/boot/dts/lpc3250-ea3250.dtb: Warning (gpios_property): power-gpio property size (12) too small for cell size 3 in /ahb/apb/i2c@400A0000/uda1380@18
It looks like the nodes are written for a different binding that combines
the GPIO number into a single number rather than a bank/number pair.
I found the right numbers on stackexchange.com, so this patch fixes
the warning and has a reasonable chance of getting things to actually
work.
Cc: stable@vger.kernel.org
Link: https://unix.stackexchange.com/questions/59497/alsa-asoc-how-to-correctly-load-devices-drivers/62217#62217
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5f1aa51c7a ]
Booting a kernel results in the kernel warning us about the following
PPI interrupts configuration:
[ 0.105127] smp: Bringing up secondary CPUs ...
[ 0.110545] GIC: PPI11 is secure or misconfigured
[ 0.110551] GIC: PPI13 is secure or misconfigured
Fix this by using the appropriate edge configuration for PPI11 and
PPI13, this is similar to what was fixed for Northstar (BCM5301X) in
commit 0e34079cd1 ("ARM: dts: BCM5301X: Correct GIC_PPI interrupt
flags").
Fixes: 7b2e987de2 ("ARM: NSP: add minimal Northstar Plus device tree")
Fixes: 1a9d53caba ("ARM: dts: NSP: Add TWD Support to DT")
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 77416ab35f ]
The AHCI controller is currently enabled for all of these boards:
bcm958623hr and bcm958625hr would result in a hard hang on boot that we
cannot get rid of. Since this does not appear to have an easy and simple
fix, just disable the AHCI controller for now until this gets resolved.
Fixes: 70725d6e97 ("ARM: dts: NSP: Enable SATA on bcm958625hr")
Fixes: d454c37624 ("ARM: dts: NSP: Add new DT file for bcm958623hr")
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 56aeb07c91 upstream.
MPP7 is currently muxed as "gpio", but this function doesn't exist for
MPP7, only "gpo" is available. This causes the following error:
kirkwood-pinctrl f1010000.pin-controller: unsupported function gpio on pin mpp7
pinctrl core: failed to register map default (6): invalid type given
kirkwood-pinctrl f1010000.pin-controller: error claiming hogs: -22
kirkwood-pinctrl f1010000.pin-controller: could not claim hogs: -22
kirkwood-pinctrl f1010000.pin-controller: unable to register pinctrl driver
kirkwood-pinctrl: probe of f1010000.pin-controller failed with error -22
So the pinctrl driver is not probed, all device drivers (including the
UART driver) do a -EPROBE_DEFER, and therefore the system doesn't
really boot (well, it boots, but with no UART, and no devices that
require pin-muxing).
Back when the Device Tree file for this board was introduced, the
definition was already wrong. The pinctrl driver also always described
as "gpo" this function for MPP7. However, between Linux 4.10 and 4.11,
a hog pin failing to be muxed was turned from a simple warning to a
hard error that caused the entire pinctrl driver probe to bail
out. This is probably the result of commit 6118714275 ("pinctrl:
core: Fix pinctrl_register_and_init() with pinctrl_enable()").
This commit fixes the Device Tree to use the proper "gpo" function for
MPP7, which fixes the boot of OpenBlocks A7, which was broken since
Linux 4.11.
Fixes: f24b56cbcd ("ARM: kirkwood: add support for OpenBlocks A7 platform")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull ARM SoC fixes from Arnd Bergmann:
"Only two patches came in over the last two weeks: Uniphier USB support
needs additional clocks enabled (on both 32-bit and 64-bit ARM), and a
Marvell MVEBU stability issue has been fixed"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: mvebu: pl310-cache disable double-linefill
arm64: dts: uniphier: add STDMAC clock to EHCI nodes
ARM: dts: uniphier: add STDMAC clock to EHCI nodes
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull "mvebu fixes for 4.14 (part 3)" from Gregory CLEMENT:
Fixing an old stability issue on Cortex A9 based mvebu SoC
* tag 'mvebu-fixes-4.14-3' of git://git.infradead.org/linux-mvebu:
ARM: dts: mvebu: pl310-cache disable double-linefill
Pull "UniPhier ARM SoC fixes for v4.14" from Masahiro Yamada:
- Add necessary clock to EHCI node
* tag 'uniphier-fixes-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
arm64: dts: uniphier: add STDMAC clock to EHCI nodes
ARM: dts: uniphier: add STDMAC clock to EHCI nodes
Under heavy system stress mvebu SoC using Cortex A9 sporadically
encountered instability issues.
The "double linefill" feature of L2 cache was identified as causing
dependency between read and write which lead to the deadlock.
Especially, it was the cause of deadlock seen under heavy PCIe traffic,
as this dependency violates PCIE overtaking rule.
Fixes: c8f5a878e5 ("ARM: mvebu: use DT properties to fine-tune the L2 configuration")
Cc: stable@vger.kernel.org
Signed-off-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
[gregory.clement@free-electrons.com: reformulate commit log, add Armada
375 and add Fixes tag]
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Pull "Allwinner fixes for 4.14" from Maxime Ripard:
Two fixes, one for the A31 DRM binding, and one for a missing regulator on
the pine MMC controller.
* tag 'sunxi-fixes-for-4.14' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun6i: Fix endpoint IDs in second display pipeline
arm64: allwinner: a64: pine64: Use dcdc1 regulator for mmc0
Without the STDMAC clock enabled, the USB 2.0 hosts do not work.
This clock must be explicitly listed in the "clocks" property because
it is independent of the other clocks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
