commit 4a014a7339 upstream.
When printer_write() calls usb_ep_queue(), a udc driver (e.g.
renesas_usbhs driver) may call usb_gadget_giveback_request() in
the udc .queue ops immediately. Then, printer_write() calls
list_add(&req->list, &dev->tx_reqs_active) wrongly. After that,
if we do unbind the printer driver, WARN_ON() happens in
printer_func_unbind() because the list entry is not removed.
So, this patch moves list_add(&req->list, &dev->tx_reqs_active)
calling before usb_ep_queue().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05826ff135 upstream.
The USB Type-C PHY in Intel WhiskeyCove PMIC has build-in
USB Type-C state machine which we were relying on to
configure the CC lines correctly. This patch removes that
dependency and configures the CC line according to commands
from the port manager (tcpm.c) in wcove_set_cc().
This fixes an issue where USB devices attached to the USB
Type-C port do not get enumerated. When acting as
source/host, the HW FSM sometimes fails to configure the PHY
correctly.
Fixes: 3c4fb9f169 ("usb: typec: wcove: start using tcpm for USB PD support")
Cc: stable@vger.kernel.org
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c4e97ddfe upstream.
The ALWAYS_SYNC flag is currently honored by the usb-storage driver but not UAS
and is required to work around devices that become unstable upon being
queried for cache. This code is taken straight from:
drivers/usb/storage/scsiglue.c:284
Signed-off-by: Alexander Kappner <agk@godking.net>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a0d6ec8809 upstream.
pdev_nr and rhport can be controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/usb/usbip/vhci_sysfs.c:238 detach_store() warn: potential spectre issue 'vhcis'
drivers/usb/usbip/vhci_sysfs.c:328 attach_store() warn: potential spectre issue 'vhcis'
drivers/usb/usbip/vhci_sysfs.c:338 attach_store() warn: potential spectre issue 'vhci->vhci_hcd_ss->vdev'
drivers/usb/usbip/vhci_sysfs.c:340 attach_store() warn: potential spectre issue 'vhci->vhci_hcd_hs->vdev'
Fix this by sanitizing pdev_nr and rhport before using them to index
vhcis and vhci->vhci_hcd_ss->vdev respectively.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0ee78c1014 ]
xhci driver displays the supported xHC USB revision in a message during
driver load:
"Host supports USB 3.1 Enhanced SuperSpeed"
Get the USB minor revision number from the xhci protocol capability.
This will show the correct supported revisions for new USB 3.2 and later
hosts
Don't rely on the SBRN (serial bus revision number) register, it's often
showing 0x30 (USB3.0) for hosts that support USB 3.1
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5d6ae4f0da ]
When handling an OS descriptor request, one of the first operations is
to zero out the request buffer using the wLength from the setup packet.
There is no bounds checking, so a wLength > 4096 would clobber memory
adjacent to the request buffer. Fix this by taking the min of wLength
and the request buffer length prior to the memset. While at it, define
the buffer length in a header file so that magic numbers don't appear
throughout the code.
When returning data to the host, the data length should be the min of
the wLength and the valid data we have to return. Currently we are
returning wLength, thus requests for a wLength greater than the amount
of data in the OS descriptor buffer would return invalid (albeit zero'd)
data following the valid descriptor data. Fix this by counting the
number of bytes when constructing the data and using this when
determining the length of the request.
Signed-off-by: Chris Dickens <christopher.a.dickens@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4058ebf33c ]
When using a AIO read() operation on the function FS gadget driver a URB is
submitted asynchronously and on URB completion the received data is copied
to the userspace buffer associated with the read operation.
This is done from a kernel worker thread invoking copy_to_user() (through
copy_to_iter()). And while the user space process memory is made available
to the kernel thread using use_mm(), some architecture require in addition
to this that the operation runs with USER_DS set. Otherwise the userspace
memory access will fail.
For example on ARM64 with Privileged Access Never (PAN) and User Access
Override (UAO) enabled the following crash occurs.
Internal error: Accessing user space memory with fs=KERNEL_DS: 9600004f [#1] SMP
Modules linked in:
CPU: 2 PID: 1636 Comm: kworker/2:1 Not tainted 4.9.0-04081-g8ab2dfb-dirty #487
Hardware name: ZynqMP ZCU102 Rev1.0 (DT)
Workqueue: events ffs_user_copy_worker
task: ffffffc87afc8080 task.stack: ffffffc87a00c000
PC is at __arch_copy_to_user+0x190/0x220
LR is at copy_to_iter+0x78/0x3c8
[...]
[<ffffff800847b790>] __arch_copy_to_user+0x190/0x220
[<ffffff80086f25d8>] ffs_user_copy_worker+0x70/0x130
[<ffffff80080b8c64>] process_one_work+0x1dc/0x460
[<ffffff80080b8f38>] worker_thread+0x50/0x4b0
[<ffffff80080bf5a0>] kthread+0xd8/0xf0
[<ffffff8008083680>] ret_from_fork+0x10/0x50
Address this by placing a set_fs(USER_DS) before of the copy operation
and revert it again once the copy operation has finished.
This patch is analogous to commit d7ffde35e3 ("vhost: use USER_DS in
vhost_worker thread") which addresses the same underlying issue.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 946ef68ad4 ]
Some UDC drivers (like the DWC3) expect that the response to a setup()
request is queued from within the setup function itself so that it is
available as soon as setup() has completed.
Upon receiving a setup request the function fs driver creates an event that
is made available to userspace. And only once userspace has acknowledged
that event the response to the setup request is queued.
So it violates the requirement of those UDC drivers and random failures can
be observed. This is basically a race condition and if userspace is able to
read the event and queue the response fast enough all is good. But if it is
not, for example because other processes are currently scheduled to run,
the USB host that sent the setup request will observe an error.
To avoid this the gadget framework provides the USB_GADGET_DELAYED_STATUS
return code. If a setup() callback returns this value the UDC driver is
aware that response is not yet available and can uses the appropriate
methods to handle this case.
Since in the case of function fs the response will never be available when
the setup() function returns make sure that this status code is used.
This fixed random occasional failures that were previously observed on a
DWC3 based system under high system load.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 92a8dd2646 ]
Added missing GUSBCFG programming in host mode, which fixes
transaction errors issue on HiKey and Altera Cyclone V boards.
These field even if was programmed in device mode (in function
dwc2_hsotg_core_init_disconnected()) will be resetting to POR values
after core soft reset applied.
So, each time when switching to host mode required to set this field
to correct value.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a400efe455 ]
set udev->slot_id to zero when disabling and freeing the xhci slot.
Prevents usb core from calling xhci with a stale slot id.
xHC controller may be reset during resume to recover from some error.
All slots are unusable as they are disabled and freed.
xhci driver starts slot enumeration again from 1 in the order they are
enabled. In the worst case a stale udev->slot_id for one device matches
a newly enabled slot_id for a different device, causing us to
perform a action on the wrong device.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c171654caa upstream.
stub_probe() calls put_busid_priv() in an error path when device isn't
found in the busid_table. Fix it by making put_busid_priv() safe to be
called with null struct bus_id_priv pointer.
This problem happens when "usbip bind" is run without loading usbip_host
driver and then running modprobe. The first failed bind attempt unbinds
the device from the original driver and when usbip_host is modprobed,
stub_probe() runs and doesn't find the device in its busid table and calls
put_busid_priv(0 with null bus_id_priv pointer.
usbip-host 3-10.2: 3-10.2 is not in match_busid table... skip!
[ 367.359679] =====================================
[ 367.359681] WARNING: bad unlock balance detected!
[ 367.359683] 4.17.0-rc4+ #5 Not tainted
[ 367.359685] -------------------------------------
[ 367.359688] modprobe/2768 is trying to release lock (
[ 367.359689]
==================================================================
[ 367.359696] BUG: KASAN: null-ptr-deref in print_unlock_imbalance_bug+0x99/0x110
[ 367.359699] Read of size 8 at addr 0000000000000058 by task modprobe/2768
[ 367.359705] CPU: 4 PID: 2768 Comm: modprobe Not tainted 4.17.0-rc4+ #5
Fixes: 22076557b0 ("usbip: usbip_host: fix NULL-ptr deref and use-after-free errors") in usb-linus
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 22076557b0 upstream.
usbip_host updates device status without holding lock from stub probe,
disconnect and rebind code paths. When multiple requests to import a
device are received, these unprotected code paths step all over each
other and drive fails with NULL-ptr deref and use-after-free errors.
The driver uses a table lock to protect the busid array for adding and
deleting busids to the table. However, the probe, disconnect and rebind
paths get the busid table entry and update the status without holding
the busid table lock. Add a new finer grain lock to protect the busid
entry. This new lock will be held to search and update the busid entry
fields from get_busid_idx(), add_match_busid() and del_match_busid().
match_busid_show() does the same to access the busid entry fields.
get_busid_priv() changed to return the pointer to the busid entry holding
the busid lock. stub_probe(), stub_disconnect() and stub_device_rebind()
call put_busid_priv() to release the busid lock before returning. This
changes fixes the unprotected code paths eliminating the race conditions
in updating the busid entries.
Reported-by: Jakub Jirasek
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7510df3f29 upstream.
After removing usbip_host module, devices it releases are left without
a driver. For example, when a keyboard or a mass storage device are
bound to usbip_host when it is removed, these devices are no longer
bound to any driver.
Fix it to run device_attach() from the module exit routine to restore
the devices to their original drivers. This includes cleanup changes
and moving device_attach() code to a common routine to be called from
rebind_store() and usbip_host_exit().
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1e180f167d upstream.
Device is left in the busid_table after unbind and rebind. Rebind
initiates usb bus scan and the original driver claims the device.
After rescan the device should be deleted from the busid_table as
it no longer belongs to usbip_host.
Fix it to delete the device after device_attach() succeeds.
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2278446e2b upstream.
Hub driver will try to disable a USB3 device twice at logical disconnect,
racing with xhci_free_dev() callback from the first port disable.
This can be triggered with "udisksctl power-off --block-device <disk>"
or by writing "1" to the "remove" sysfs file for a USB3 device
in 4.17-rc4.
USB3 devices don't have a similar disabled link state as USB2 devices,
and use a U3 suspended link state instead. In this state the port
is still enabled and connected.
hub_port_connect() first disconnects the device, then later it notices
that device is still enabled (due to U3 states) it will try to disable
the port again (set to U3).
The xhci_free_dev() called during device disable is async, so checking
for existing xhci->devs[i] when setting link state to U3 the second time
was successful, even if device was being freed.
The regression was caused by, and whole thing revealed by,
Commit 44a182b9d1 ("xhci: Fix use-after-free in xhci_free_virt_device")
which sets xhci->devs[i]->udev to NULL before xhci_virt_dev() returned.
and causes a NULL pointer dereference the second time we try to set U3.
Fix this by checking xhci->devs[i]->udev exists before setting link state.
The original patch went to stable so this fix needs to be applied there as
well.
Fixes: 44a182b9d1 ("xhci: Fix use-after-free in xhci_free_virt_device")
Cc: <stable@vger.kernel.org>
Reported-by: Jordan Glover <Golden_Miller83@protonmail.ch>
Tested-by: Jordan Glover <Golden_Miller83@protonmail.ch>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9aea9b6cc7 upstream.
The usb_request pointer could be NULL in musb_g_tx(), where the
tracepoint call would trigger the NULL pointer dereference failure when
parsing the members of the usb_request pointer.
Move the tracepoint call to where the usb_request pointer is already
checked to solve the issue.
Fixes: fc78003e53 ("usb: musb: gadget: add usb-request tracepoints")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2b63f1329d upstream.
musb_start_urb() doesn't check the pass-in parameter if it is NULL. But
in musb_bulk_nak_timeout() the parameter passed to musb_start_urb() is
returned from first_qh(), which could be NULL.
So wrap the musb_start_urb() call here with a if condition check to
avoid the potential NULL pointer dereference.
Fixes: f283862f3b ("usb: musb: NAK timeout scheme on bulk TX endpoint")
Cc: stable@vger.kernel.org # v3.7+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c3a65808f0 upstream.
Reimplement interface masking using device flags stored directly in the
device-id table. This will make it easier to add and maintain device-id
entries by using a more compact and readable notation compared to the
current implementation (which manages pairs of masks in separate
blacklist structs).
Two convenience macros are used to flag an interface as either reserved
or as not supporting modem-control requests:
{ USB_DEVICE(TELIT_VENDOR_ID, TELIT_PRODUCT_ME910_DUAL_MODEM),
.driver_info = NCTRL(0) | RSVD(3) },
For now, we limit the highest maskable interface number to seven, which
allows for (up to 16) additional device flags to be added later should
need arise.
Note that this will likely need to be backported to stable in order to
make future device-id backports more manageable.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb5ee84ea7 upstream.
Some non-compliant high-speed USB devices have bulk endpoints with a
1024-byte maxpacket size. Although such endpoints don't work with
xHCI host controllers, they do work with EHCI controllers. We used to
accept these invalid sizes (with a warning), but we no longer do
because of an unintentional change introduced by commit aed9d65ac3
("USB: validate wMaxPacketValue entries in endpoint descriptors").
This patch restores the old behavior, so that people with these
peculiar devices can use them without patching their kernels by hand.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Elvinas <elvinas@veikia.lt>
Fixes: aed9d65ac3 ("USB: validate wMaxPacketValue entries in endpoint descriptors")
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 96bd39df29 upstream.
dwc3_ep_dequeue() waits for completion of End Transfer command using
wait_event_lock_irq(), which will release the dwc3->lock while waiting
and reacquire after completion. This allows a potential race condition
with ep_disable() which also removes all requests from started_list
and pending_list.
The check for NULL r->trb should catch this but currently it exits to
the wrong 'out1' label which calls dwc3_gadget_giveback(). Since its
list entry was already removed, if CONFIG_DEBUG_LIST is enabled a
'list_del corruption' bug is thrown since its next/prev pointers are
already LIST_POISON1/2. If r->trb is NULL it should simply exit to
'out0'.
Fixes: cf3113d893 ("usb: dwc3: gadget: properly increment dequeue pointer on ep_dequeue")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4842ed5bfc upstream.
If we get an invalid device configuration from a palm 3 type device, we
might incorrectly parse things, and we have the potential to crash in
"interesting" ways.
Fix this up by verifying the size of the configuration passed to us by
the device, and only if it is correct, will we handle it.
Note that this also fixes an information leak of slab data.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ johan: add comment about the info leak ]
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 44a182b9d1 upstream.
KASAN found a use-after-free in xhci_free_virt_device+0x33b/0x38e
where xhci_free_virt_device() sets slot id to 0 if udev exists:
if (dev->udev && dev->udev->slot_id)
dev->udev->slot_id = 0;
dev->udev will be true even if udev is freed because dev->udev is
not set to NULL.
set dev->udev pointer to NULL in xhci_free_dev()
The original patch went to stable so this fix needs to be applied
there as well.
Fixes: a400efe455 ("xhci: zero usb device slot_id member when disabling and freeing a xhci slot")
Cc: <stable@vger.kernel.org>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83a62c51ba upstream.
On chromebooks we depend on wakeup count to identify the wakeup source.
But currently USB devices do not increment the wakeup count when they
trigger the remote wake. This patch addresses the same.
Resume condition is reported differently on USB 2.0 and USB 3.0 devices.
On USB 2.0 devices, a wake capable device, if wake enabled, drives
resume signal to indicate a remote wake (USB 2.0 spec section 7.1.7.7).
The upstream facing port then sets C_PORT_SUSPEND bit and reports a
port change event (USB 2.0 spec section 11.24.2.7.2.3). Thus if a port
has resumed before driving the resume signal from the host and
C_PORT_SUSPEND is set, then the device attached to the given port might
be the reason for the last system wakeup. Increment the wakeup count for
the same.
On USB 3.0 devices, a function may signal that it wants to exit from device
suspend by sending a Function Wake Device Notification to the host (USB3.0
spec section 8.5.6.4) Thus on receiving the Function Wake, increment the
wakeup count.
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 470b5d6f0c upstream.
Arrow USB Blaster integrated on MAX1000 board uses the same vendor ID
(0x0403) and product ID (0x6010) as the "original" FTDI device.
This patch avoids picking up by ftdi_sio of the first interface of this
USB device. After that this device can be used by Arrow user-space JTAG
driver.
Signed-off-by: Vasyl Vavrychuk <vvavrychuk@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 621faf4f6a upstream.
The Dell Inspiron 5775 is a Raven Ridge. The Enable Slot command timed
out when a USB device gets plugged:
[ 212.156326] xhci_hcd 0000:03:00.3: Error while assigning device slot ID
[ 212.156340] xhci_hcd 0000:03:00.3: Max number of devices this xHCI host supports is 64.
[ 212.156348] usb usb2-port3: couldn't allocate usb_device
AMD suggests that a delay before xHC suspends can fix the issue.
I can confirm it fixes the issue, so use the suspend delay quirk for
Raven Ridge's xHC.
Cc: stable@vger.kernel.org
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c91815b596 upstream.
This is a requirement which has always existed but, somehow, wasn't
reflected in the documentation and problems weren't found until now
when Tuba Yavuz found a possible deadlock happening between dwc3 and
f_hid. She described the situation as follows:
spin_lock_irqsave(&hidg->write_spinlock, flags); // first acquire
/* we our function has been disabled by host */
if (!hidg->req) {
free_ep_req(hidg->in_ep, hidg->req);
goto try_again;
}
[...]
status = usb_ep_queue(hidg->in_ep, hidg->req, GFP_ATOMIC);
=>
[...]
=> usb_gadget_giveback_request
=>
f_hidg_req_complete
=>
spin_lock_irqsave(&hidg->write_spinlock, flags); // second acquire
Note that this happens because dwc3 would call ->complete() on a
failed usb_ep_queue() due to failed Start Transfer command. This is,
anyway, a theoretical situation because dwc3 currently uses "No
Response Update Transfer" command for Bulk and Interrupt endpoints.
It's still good to make this case impossible to happen even if the "No
Reponse Update Transfer" command is changed.
Reported-by: Tuba Yavuz <tuba@ece.ufl.edu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
