[ Upstream commit fa1be7e01e ]
Some of the code paths calculating flow hash for IPv6 use flowlabel member
of struct flowi6 which, despite its name, encodes both flow label and
traffic class. If traffic class changes within a TCP connection (as e.g.
ssh does), ECMP route can switch between path. It's also inconsistent with
other code paths where ip6_flowlabel() (returning only flow label) is used
to feed the key.
Use only flow label everywhere, including one place where hash key is set
using ip6_flowinfo().
Fixes: 51ebd31815 ("ipv6: add support of equal cost multipath (ECMP)")
Fixes: f70ea018da ("net: Add functions to get skb->hash based on flow structures")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 21706ee8a4 ]
There was a regression at some point from the intended functionality of
commit f60c3704e8 ("bonding: Fix alb mode to only use first level
vlans.")
Given the return value vlan_get_encap_level() we need to store the nest
level of the bond device, and then compare the vlan's encap level to
this. Without this, this check always fails and learning packets are
never sent.
In addition, this same commit caused a regression in the behavior of
balance_alb, which requires learning packets be sent for all interfaces
using the slave's mac in order to load balance properly. For vlan's
that have not set a user mac, we can send after checking one bit.
Otherwise we need send the set mac, albeit defeating rx load balancing
for that vlan.
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c212d2c7fc ]
It is reported that in some cases, write_space may be called in
do_tcp_sendpages, such that we recursively invoke do_tcp_sendpages again:
[ 660.468802] ? do_tcp_sendpages+0x8d/0x580
[ 660.468826] ? tls_push_sg+0x74/0x130 [tls]
[ 660.468852] ? tls_push_record+0x24a/0x390 [tls]
[ 660.468880] ? tls_write_space+0x6a/0x80 [tls]
...
tls_push_sg already does a loop over all sending sg's, so ignore
any tls_write_space notifications until we are done sending.
We then have to call the previous write_space to wake up
poll() waiters after we are done with the send loop.
Reported-by: Andre Tomt <andre@tomt.net>
Signed-off-by: Dave Watson <davejwatson@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1993a2de1 upstream.
syzbot reported :
BUG: KMSAN: uninit-value in rtnh_ok include/net/nexthop.h:11 [inline]
BUG: KMSAN: uninit-value in fib_count_nexthops net/ipv4/fib_semantics.c:469 [inline]
BUG: KMSAN: uninit-value in fib_create_info+0x554/0x8d20 net/ipv4/fib_semantics.c:1091
@remaining is an integer, coming from user space.
If it is negative we want rtnh_ok() to return false.
Fixes: 4e902c5741 ("[IPv4]: FIB configuration using struct fib_config")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cc74eddd0f ]
There is currently no handling to check on a invalid tlv length. This
patch adds such handling to avoid killing the kernel with a malformed
ife packet.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Reviewed-by: Yotam Gigi <yotam.gi@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b905ef9ab9 ]
The connection timers of an llc sock could be still flying
after we delete them in llc_sk_free(), and even possibly
after we free the sock. We could just wait synchronously
here in case of troubles.
Note, I leave other call paths as they are, since they may
not have to wait, at least we can change them to synchronously
when needed.
Also, move the code to net/llc/llc_conn.c, which is apparently
a better place.
Reported-by: <syzbot+f922284c18ea23a8e457@syzkaller.appspotmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3f01ddb962 ]
On receiving a packet the state index points to the rstate which must be
used to fill up IP and TCP headers. But if the state index points to a
rstate which is unitialized, i.e. filled with zeros, it gets stuck in an
infinite loop inside ip_fast_csum trying to compute the ip checsum of a
header with zero length.
89.666953: <2> [<ffffff9dd3e94d38>] slhc_uncompress+0x464/0x468
89.666965: <2> [<ffffff9dd3e87d88>] ppp_receive_nonmp_frame+0x3b4/0x65c
89.666978: <2> [<ffffff9dd3e89dd4>] ppp_receive_frame+0x64/0x7e0
89.666991: <2> [<ffffff9dd3e8a708>] ppp_input+0x104/0x198
89.667005: <2> [<ffffff9dd3e93868>] pppopns_recv_core+0x238/0x370
89.667027: <2> [<ffffff9dd4428fc8>] __sk_receive_skb+0xdc/0x250
89.667040: <2> [<ffffff9dd3e939e4>] pppopns_recv+0x44/0x60
89.667053: <2> [<ffffff9dd4426848>] __sock_queue_rcv_skb+0x16c/0x24c
89.667065: <2> [<ffffff9dd4426954>] sock_queue_rcv_skb+0x2c/0x38
89.667085: <2> [<ffffff9dd44f7358>] raw_rcv+0x124/0x154
89.667098: <2> [<ffffff9dd44f7568>] raw_local_deliver+0x1e0/0x22c
89.667117: <2> [<ffffff9dd44c8ba0>] ip_local_deliver_finish+0x70/0x24c
89.667131: <2> [<ffffff9dd44c92f4>] ip_local_deliver+0x100/0x10c
./scripts/faddr2line vmlinux slhc_uncompress+0x464/0x468 output:
ip_fast_csum at arch/arm64/include/asm/checksum.h:40
(inlined by) slhc_uncompress at drivers/net/slip/slhc.c:615
Adding a variable to indicate if the current rstate is initialized. If
such a packet arrives, move to toss state.
Signed-off-by: Tejaswi Tanikella <tejaswit@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
llc_conn_send_pdu() pushes the skb into write queue and
calls llc_conn_send_pdus() to flush them out. However, the
status of dev_queue_xmit() is not returned to caller,
in this case, llc_conn_state_process().
llc_conn_state_process() needs hold the skb no matter
success or failure, because it still uses it after that,
therefore we should hold skb before dev_queue_xmit() when
that skb is the one being processed by llc_conn_state_process().
For other callers, they can just pass NULL and ignore
the return value as they are.
Reported-by: Noam Rathaus <noamr@beyondsecurity.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the qdisc lock was dropped in pfifo_fast we allow multiple
enqueue threads and dequeue threads to run in parallel. On the
enqueue side the skb bit ooo_okay is used to ensure all related
skbs are enqueued in-order. On the dequeue side though there is
no similar logic. What we observe is with fewer queues than CPUs
it is possible to re-order packets when two instances of
__qdisc_run() are running in parallel. Each thread will dequeue
a skb and then whichever thread calls the ndo op first will
be sent on the wire. This doesn't typically happen because
qdisc_run() is usually triggered by the same core that did the
enqueue. However, drivers will trigger __netif_schedule()
when queues are transitioning from stopped to awake using the
netif_tx_wake_* APIs. When this happens netif_schedule() calls
qdisc_run() on the same CPU that did the netif_tx_wake_* which
is usually done in the interrupt completion context. This CPU
is selected with the irq affinity which is unrelated to the
enqueue operations.
To resolve this we add a RUNNING bit to the qdisc to ensure
only a single dequeue per qdisc is running. Enqueue and dequeue
operations can still run in parallel and also on multi queue
NICs we can still have a dequeue in-flight per qdisc, which
is typically per CPU.
Fixes: c5ad119fb6 ("net: sched: pfifo_fast use skb_array")
Reported-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree,
they are:
1) Don't pick fixed hash implementation for NFT_SET_EVAL sets, otherwise
userspace hits EOPNOTSUPP with valid rules using the meter statement,
from Florian Westphal.
2) If you send a batch that flushes the existing ruleset (that contains
a NAT chain) and the new ruleset definition comes with a new NAT
chain, don't bogusly hit EBUSY. Also from Florian.
3) Missing netlink policy attribute validation, from Florian.
4) Detach conntrack template from skbuff if IP_NODEFRAG is set on,
from Paolo Abeni.
5) Cache device names in flowtable object, otherwise we may end up
walking over devices going aways given no rtnl_lock is held.
6) Fix incorrect net_device ingress with ingress hooks.
7) Fix crash when trying to read more data than available in UDP
packets from the nf_socket infrastructure, from Subash.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Devices going away have to grab the nfnl_lock from the netdev event path
to avoid races with control plane updates.
However, netlink dumps in netfilter do not hold nfnl_lock mutex. Cache
the device name into the objects to avoid an use-after-free situation
for a device that is going away.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Commit 7b6ddeaf27 ("mac80211: use QoS NDP for AP probing") added an
argument qos_ok to ieee80211_nullfunc_get to support QoS NDP. Despite
the claim in the commit log "Change all the drivers to *not* allow
QoS NDP for now, even though it looks like most of them should be OK
with that", this commit enables QoS NDP in response to beacons (see
change to mlme.c:ieee80211_send_nullfunc), causing ath9k_htc to lose
IP connectivity. See:
https://patchwork.kernel.org/patch/10241109/https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=891060
Introduce a hardware flag to allow such buggy drivers to override the
correct default behaviour of mac80211 of sending QoS NDP packets.
Signed-off-by: Ben Caradoc-Davies <ben@transient.nz>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Prior to the rework of PMTU information storage in commit
2c8cec5c10 ("ipv4: Cache learned PMTU information in inetpeer."),
when a PMTU event advertising a PMTU smaller than
net.ipv4.route.min_pmtu was received, we would disable setting the DF
flag on packets by locking the MTU metric, and set the PMTU to
net.ipv4.route.min_pmtu.
Since then, we don't disable DF, and set PMTU to
net.ipv4.route.min_pmtu, so the intermediate router that has this link
with a small MTU will have to drop the packets.
This patch reestablishes pre-2.6.39 behavior by splitting
rtable->rt_pmtu into a bitfield with rt_mtu_locked and rt_pmtu.
rt_mtu_locked indicates that we shouldn't set the DF bit on that path,
and is checked in ip_dont_fragment().
One possible workaround is to set net.ipv4.route.min_pmtu to a value low
enough to accommodate the lowest MTU encountered.
Fixes: 2c8cec5c10 ("ipv4: Cache learned PMTU information in inetpeer.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2018-03-13
1) Refuse to insert 32 bit userspace socket policies on 64
bit systems like we do it for standard policies. We don't
have a compat layer, so inserting socket policies from
32 bit userspace will lead to a broken configuration.
2) Make the policy hold queue work without the flowcache.
Dummy bundles are not chached anymore, so we need to
generate a new one on each lookup as long as the SAs
are not yet in place.
3) Fix the validation of the esn replay attribute. The
The sanity check in verify_replay() is bypassed if
the XFRM_STATE_ESN flag is not set. Fix this by doing
the sanity check uncoditionally.
From Florian Westphal.
4) After most of the dst_entry garbage collection code
is removed, we may leak xfrm_dst entries as they are
neither cached nor tracked somewhere. Fix this by
reusing the 'uncached_list' to track xfrm_dst entries
too. From Xin Long.
5) Fix a rcu_read_lock/rcu_read_unlock imbalance in
xfrm_get_tos() From Xin Long.
6) Fix an infinite loop in xfrm_get_dst_nexthop. On
transport mode we fetch the child dst_entry after
we continue, so this pointer is never updated.
Fix this by fetching it before we continue.
7) Fix ESN sequence number gap after IPsec GSO packets.
We accidentally increment the sequence number counter
on the xfrm_state by one packet too much in the ESN
case. Fix this by setting the sequence number to the
correct value.
8) Reset the ethernet protocol after decapsulation only if a
mac header was set. Otherwise it breaks configurations
with TUN devices. From Yossi Kuperman.
9) Fix __this_cpu_read() usage in preemptible code. Use
this_cpu_read() instead in ipcomp_alloc_tfms().
From Greg Hackmann.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when using 'ss' in iproute, kernel would try to load all _diag
modules, which also causes corresponding family and proto modules
to be loaded as well due to module dependencies.
Like after running 'ss', sctp, dccp, af_packet (if it works as a module)
would be loaded.
For example:
$ lsmod|grep sctp
$ ss
$ lsmod|grep sctp
sctp_diag 16384 0
sctp 323584 5 sctp_diag
inet_diag 24576 4 raw_diag,tcp_diag,sctp_diag,udp_diag
libcrc32c 16384 3 nf_conntrack,nf_nat,sctp
As these family and proto modules are loaded unintentionally, it
could cause some problems, like:
- Some debug tools use 'ss' to collect the socket info, which loads all
those diag and family and protocol modules. It's noisy for identifying
issues.
- Users usually expect to drop sctp init packet silently when they
have no sense of sctp protocol instead of sending abort back.
- It wastes resources (especially with multiple netns), and SCTP module
can't be unloaded once it's loaded.
...
In short, it's really inappropriate to have these family and proto
modules loaded unexpectedly when just doing debugging with inet_diag.
This patch is to introduce sock_load_diag_module() where it loads
the _diag module only when it's corresponding family or proto has
been already registered.
Note that we can't just load _diag module without the family or
proto loaded, as some symbols used in _diag module are from the
family or proto module.
v1->v2:
- move inet proto check to inet_diag to avoid a compiling err.
v2->v3:
- define sock_load_diag_module in sock.c and export one symbol
only.
- improve the changelog.
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Phil Sutter <phil@nwl.cc>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we exceed current packets limit and we have more than one
segment in the list returned by skb_gso_segment(), netem drops
only the first one, skipping the rest, hence kmemleak reports:
unreferenced object 0xffff880b5d23b600 (size 1024):
comm "softirq", pid 0, jiffies 4384527763 (age 2770.629s)
hex dump (first 32 bytes):
00 80 23 5d 0b 88 ff ff 00 00 00 00 00 00 00 00 ..#]............
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000d8a19b9d>] __alloc_skb+0xc9/0x520
[<000000001709b32f>] skb_segment+0x8c8/0x3710
[<00000000c7b9bb88>] tcp_gso_segment+0x331/0x1830
[<00000000c921cba1>] inet_gso_segment+0x476/0x1370
[<000000008b762dd4>] skb_mac_gso_segment+0x1f9/0x510
[<000000002182660a>] __skb_gso_segment+0x1dd/0x620
[<00000000412651b9>] netem_enqueue+0x1536/0x2590 [sch_netem]
[<0000000005d3b2a9>] __dev_queue_xmit+0x1167/0x2120
[<00000000fc5f7327>] ip_finish_output2+0x998/0xf00
[<00000000d309e9d3>] ip_output+0x1aa/0x2c0
[<000000007ecbd3a4>] tcp_transmit_skb+0x18db/0x3670
[<0000000042d2a45f>] tcp_write_xmit+0x4d4/0x58c0
[<0000000056a44199>] tcp_tasklet_func+0x3d9/0x540
[<0000000013d06d02>] tasklet_action+0x1ca/0x250
[<00000000fcde0b8b>] __do_softirq+0x1b4/0x5a3
[<00000000e7ed027c>] irq_exit+0x1e2/0x210
Fix it by adding the rest of the segments, if any, to skb 'to_free'
list. Add new __qdisc_drop_all() and qdisc_drop_all() functions
because they can be useful in the future if we need to drop segmented
GSO packets in other places.
Fixes: 6071bd1aa1 ("netem: Segment GSO packets on enqueue")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code uses global variables, adjusts them and passes pointer down
to devlink. With every other mlxsw_core instance, the previously passed
pointer values are rewritten. Fix this by de-globalize the variables and
also memcpy size_params during devlink resource registration.
Also, introduce a convenient size_param_init helper.
Fixes: ef3116e540 ("mlxsw: spectrum: Register KVD resources with devlink")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johannes Berg says:
====================
Various fixes across the tree, the shortlog basically says it all:
cfg80211: fix cfg80211_beacon_dup
-> old bug in this code
cfg80211: clear wep keys after disconnection
-> certain ways of disconnecting left the keys
mac80211: round IEEE80211_TX_STATUS_HEADROOM up to multiple of 4
-> alignment issues with using 14 bytes
mac80211: Do not disconnect on invalid operating class
-> if the AP has a bogus operating class, let it be
mac80211: Fix sending ADDBA response for an ongoing session
-> don't send the same frame twice
cfg80211: use only 1Mbps for basic rates in mesh
-> interop issue with old versions of our code
mac80211_hwsim: don't use WQ_MEM_RECLAIM
-> it causes splats because it flushes work on a non-reclaim WQ
regulatory: add NUL to request alpha2
-> nla_put_string() issue from Kees
mac80211: mesh: fix wrong mesh TTL offset calculation
-> protocol issue
mac80211: fix a possible leak of station stats
-> error path might leak memory
mac80211: fix calling sleeping function in atomic context
-> percpu allocations need to be made with gfp flags
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to the ancient commit a5fe8e7695 ("regulatory: add NUL
to alpha2"), add another byte to alpha2 in the request struct so
that when we use nla_put_string(), we don't overrun anything.
Fixes: 73d54c9e74 ("cfg80211: add regulatory netlink multicast group")
Reported-by: Kees Cook <keescook@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This ensures that mac80211 allocated management frames are properly
aligned, which makes copying them more efficient.
For instance, mt76 uses iowrite32_copy to copy beacon frames to beacon
template memory on the chip.
Misaligned 32-bit accesses cause CPU exceptions on MIPS and should be
avoided.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since UDP-Lite is always using checksum, the following path is
triggered when calculating pseudo header for it:
udp4_csum_init() or udp6_csum_init()
skb_checksum_init_zero_check()
__skb_checksum_validate_complete()
The problem can appear if skb->len is less than CHECKSUM_BREAK. In
this particular case __skb_checksum_validate_complete() also invokes
__skb_checksum_complete(skb). If UDP-Lite is using partial checksum
that covers only part of a packet, the function will return bad
checksum and the packet will be dropped.
It can be fixed if we skip skb_checksum_init_zero_check() and only
set the required pseudo header checksum for UDP-Lite with partial
checksum before udp4_csum_init()/udp6_csum_init() functions return.
Fixes: ed70fcfcee ("net: Call skb_checksum_init in IPv4")
Fixes: e4f45b7f40 ("net: Call skb_checksum_init in IPv6")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In early time, when freeing a xdst, it would be inserted into
dst_garbage.list first. Then if it's refcnt was still held
somewhere, later it would be put into dst_busy_list in
dst_gc_task().
When one dev was being unregistered, the dev of these dsts in
dst_busy_list would be set with loopback_dev and put this dev.
So that this dev's removal wouldn't get blocked, and avoid the
kmsg warning:
kernel:unregister_netdevice: waiting for veth0 to become \
free. Usage count = 2
However after Commit 52df157f17 ("xfrm: take refcnt of dst
when creating struct xfrm_dst bundle"), the xdst will not be
freed with dst gc, and this warning happens.
To fix it, we need to find these xdsts that are still held by
others when removing the dev, and free xdst's dev and set it
with loopback_dev.
But unfortunately after flow_cache for xfrm was deleted, no
list tracks them anymore. So we need to save these xdsts
somewhere to release the xdst's dev later.
To make this easier, this patch is to reuse uncached_list to
track xdsts, so that the dev refcnt can be released in the
event NETDEV_UNREGISTER process of fib_netdev_notifier.
Thanks to Florian, we could move forward this fix quickly.
Fixes: 52df157f17 ("xfrm: take refcnt of dst when creating struct xfrm_dst bundle")
Reported-by: Jianlin Shi <jishi@redhat.com>
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Tested-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Daniel Borkmann says:
====================
pull-request: bpf 2018-02-09
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Two fixes for BPF sockmap in order to break up circular map references
from programs attached to sockmap, and detaching related sockets in
case of socket close() event. For the latter we get rid of the
smap_state_change() and plug into ULP infrastructure, which will later
also be used for additional features anyway such as TX hooks. For the
second issue, dependency chain is broken up via map release callback
to free parse/verdict programs, all from John.
2) Fix a libbpf relocation issue that was found while implementing XDP
support for Suricata project. Issue was that when clang was invoked
with default target instead of bpf target, then various other e.g.
debugging relevant sections are added to the ELF file that contained
relocation entries pointing to non-BPF related sections which libbpf
trips over instead of skipping them. Test cases for libbpf are added
as well, from Jesper.
3) Various misc fixes for bpftool and one for libbpf: a small addition
to libbpf to make sure it recognizes all standard section prefixes.
Then, the Makefile in bpftool/Documentation is improved to explicitly
check for rst2man being installed on the system as we otherwise risk
installing empty man pages; the man page for bpftool-map is corrected
and a set of missing bash completions added in order to avoid shipping
bpftool where the completions are only partially working, from Quentin.
4) Fix applying the relocation to immediate load instructions in the
nfp JIT which were missing a shift, from Jakub.
5) Two fixes for the BPF kernel selftests: handle CONFIG_BPF_JIT_ALWAYS_ON=y
gracefully in test_bpf.ko module and mark them as FLAG_EXPECTED_FAIL
in this case; and explicitly delete the veth devices in the two tests
test_xdp_{meta,redirect}.sh before dismantling the netnses as when
selftests are run in batch mode, then workqueue to handle destruction
might not have finished yet and thus veth creation in next test under
same dev name would fail, from Yonghong.
6) Fix test_kmod.sh to check the test_bpf.ko module path before performing
an insmod, and fallback to modprobe. Especially the latter is useful
when having a device under test that has the modules installed instead,
from Naresh.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for you net tree, they
are:
1) Restore __GFP_NORETRY in xt_table allocations to mitigate effects of
large memory allocation requests, from Michal Hocko.
2) Release IPv6 fragment queue in case of error in fragmentation header,
this is a follow up to amend patch 83f1999cae, from Subash Abhinov
Kasiviswanathan.
3) Flowtable infrastructure depends on NETFILTER_INGRESS as it registers
a hook for each flowtable, reported by John Crispin.
4) Missing initialization of info->priv in xt_cgroup version 1, from
Cong Wang.
5) Give a chance to garbage collector to run after scheduling flowtable
cleanup.
6) Releasing flowtable content on nft_flow_offload module removal is
not required at all, there is not dependencies between this module
and flowtables, remove it.
7) Fix missing xt_rateest_mutex grabbing for hash insertions, also from
Cong Wang.
8) Move nf_flow_table_cleanup() routine to flowtable core, this patch is
a dependency for the next patch in this list.
9) Flowtable resources are not properly released on removal from the
control plane. Fix this resource leak by scheduling removal of all
entries and explicit call to the garbage collector.
10) nf_ct_nat_offset() declaration is dead code, this function prototype
is not used anywhere, remove it. From Taehee Yoo.
11) Fix another flowtable resource leak on entry insertion failures,
this patch also fixes a possible use-after-free. Patch from Felix
Fietkau.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
flow_offload_del frees the flow, so all associated resource must be
freed before.
Since the ct entry in struct flow_offload_entry was allocated by
flow_offload_alloc, it should be freed by flow_offload_free to take care
of the error handling path when flow_offload_add fails.
While at it, make flow_offload_del static, since it should never be
called directly, only from the gc step
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Every flow_offload entry is added into the table twice. Because of this,
rhashtable_free_and_destroy can't be used, since it would call kfree for
each flow_offload object twice.
This patch cleans up the flowtable via nf_flow_table_iterate() to
schedule removal of entries by setting on the dying bit, then there is
an explicitly invocation of the garbage collector to release resources.
Based on patch from Felix Fietkau.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Move the flowtable cleanup routines to nf_flow_table and expose the
nf_flow_table_cleanup() helper function.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Commit d350a82302 ("net: erspan: create erspan metadata uapi header")
moves the erspan 'version' in front of the 'struct erspan_md2' for
later extensibility reason. This breaks the existing erspan metadata
extraction code because the erspan_md2 then has a 4-byte offset
to between the erspan_metadata and erspan_base_hdr. This patch
fixes it.
Fixes: 1a66a836da ("gre: add collect_md mode to ERSPAN tunnel")
Fixes: ef7baf5e08 ("ip6_gre: add ip6 erspan collect_md mode")
Fixes: 1d7e2ed22f ("net: erspan: refactor existing erspan code")
Signed-off-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The selftests test_maps program was leaving dangling BPF sockmap
programs around because not all psock elements were removed from
the map. The elements in turn hold a reference on the BPF program
they are attached to causing BPF programs to stay open even after
test_maps has completed.
The original intent was that sk_state_change() would be called
when TCP socks went through TCP_CLOSE state. However, because
socks may be in SOCK_DEAD state or the sock may be a listening
socket the event is not always triggered.
To resolve this use the ULP infrastructure and register our own
proto close() handler. This fixes the above case.
Fixes: 174a79ff95 ("bpf: sockmap with sk redirect support")
Reported-by: Prashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Create a UID field and enum that can be used to assign ULPs to
sockets. This saves a set of string comparisons if the ULP id
is known.
For sockmap, which is added in the next patches, a ULP is used to
hook into TCP sockets close state. In this case the ULP being added
is done at map insert time and the ULP is known and done on the kernel
side. In this case the named lookup is not needed. Because we don't
want to expose psock internals to user space socket options a user
visible flag is also added. For TLS this is set for BPF it will be
cleared.
Alos remove pr_notice, user gets an error code back and should check
that rather than rely on logs.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Pull hardened usercopy whitelisting from Kees Cook:
"Currently, hardened usercopy performs dynamic bounds checking on slab
cache objects. This is good, but still leaves a lot of kernel memory
available to be copied to/from userspace in the face of bugs.
To further restrict what memory is available for copying, this creates
a way to whitelist specific areas of a given slab cache object for
copying to/from userspace, allowing much finer granularity of access
control.
Slab caches that are never exposed to userspace can declare no
whitelist for their objects, thereby keeping them unavailable to
userspace via dynamic copy operations. (Note, an implicit form of
whitelisting is the use of constant sizes in usercopy operations and
get_user()/put_user(); these bypass all hardened usercopy checks since
these sizes cannot change at runtime.)
This new check is WARN-by-default, so any mistakes can be found over
the next several releases without breaking anyone's system.
The series has roughly the following sections:
- remove %p and improve reporting with offset
- prepare infrastructure and whitelist kmalloc
- update VFS subsystem with whitelists
- update SCSI subsystem with whitelists
- update network subsystem with whitelists
- update process memory with whitelists
- update per-architecture thread_struct with whitelists
- update KVM with whitelists and fix ioctl bug
- mark all other allocations as not whitelisted
- update lkdtm for more sensible test overage"
* tag 'usercopy-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (38 commits)
lkdtm: Update usercopy tests for whitelisting
usercopy: Restrict non-usercopy caches to size 0
kvm: x86: fix KVM_XEN_HVM_CONFIG ioctl
kvm: whitelist struct kvm_vcpu_arch
arm: Implement thread_struct whitelist for hardened usercopy
arm64: Implement thread_struct whitelist for hardened usercopy
x86: Implement thread_struct whitelist for hardened usercopy
fork: Provide usercopy whitelisting for task_struct
fork: Define usercopy region in thread_stack slab caches
fork: Define usercopy region in mm_struct slab caches
net: Restrict unwhitelisted proto caches to size 0
sctp: Copy struct sctp_sock.autoclose to userspace using put_user()
sctp: Define usercopy region in SCTP proto slab cache
caif: Define usercopy region in caif proto slab cache
ip: Define usercopy region in IP proto slab cache
net: Define usercopy region in struct proto slab cache
scsi: Define usercopy region in scsi_sense_cache slab cache
cifs: Define usercopy region in cifs_request slab cache
vxfs: Define usercopy region in vxfs_inode slab cache
ufs: Define usercopy region in ufs_inode_cache slab cache
...
Pull networking updates from David Miller:
1) Significantly shrink the core networking routing structures. Result
of http://vger.kernel.org/~davem/seoul2017_netdev_keynote.pdf
2) Add netdevsim driver for testing various offloads, from Jakub
Kicinski.
3) Support cross-chip FDB operations in DSA, from Vivien Didelot.
4) Add a 2nd listener hash table for TCP, similar to what was done for
UDP. From Martin KaFai Lau.
5) Add eBPF based queue selection to tun, from Jason Wang.
6) Lockless qdisc support, from John Fastabend.
7) SCTP stream interleave support, from Xin Long.
8) Smoother TCP receive autotuning, from Eric Dumazet.
9) Lots of erspan tunneling enhancements, from William Tu.
10) Add true function call support to BPF, from Alexei Starovoitov.
11) Add explicit support for GRO HW offloading, from Michael Chan.
12) Support extack generation in more netlink subsystems. From Alexander
Aring, Quentin Monnet, and Jakub Kicinski.
13) Add 1000BaseX, flow control, and EEE support to mvneta driver. From
Russell King.
14) Add flow table abstraction to netfilter, from Pablo Neira Ayuso.
15) Many improvements and simplifications to the NFP driver bpf JIT,
from Jakub Kicinski.
16) Support for ipv6 non-equal cost multipath routing, from Ido
Schimmel.
17) Add resource abstration to devlink, from Arkadi Sharshevsky.
18) Packet scheduler classifier shared filter block support, from Jiri
Pirko.
19) Avoid locking in act_csum, from Davide Caratti.
20) devinet_ioctl() simplifications from Al viro.
21) More TCP bpf improvements from Lawrence Brakmo.
22) Add support for onlink ipv6 route flag, similar to ipv4, from David
Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1925 commits)
tls: Add support for encryption using async offload accelerator
ip6mr: fix stale iterator
net/sched: kconfig: Remove blank help texts
openvswitch: meter: Use 64-bit arithmetic instead of 32-bit
tcp_nv: fix potential integer overflow in tcpnv_acked
r8169: fix RTL8168EP take too long to complete driver initialization.
qmi_wwan: Add support for Quectel EP06
rtnetlink: enable IFLA_IF_NETNSID for RTM_NEWLINK
ipmr: Fix ptrdiff_t print formatting
ibmvnic: Wait for device response when changing MAC
qlcnic: fix deadlock bug
tcp: release sk_frag.page in tcp_disconnect
ipv4: Get the address of interface correctly.
net_sched: gen_estimator: fix lockdep splat
net: macb: Handle HRESP error
net/mlx5e: IPoIB, Fix copy-paste bug in flow steering refactoring
ipv6: addrconf: break critical section in addrconf_verify_rtnl()
ipv6: change route cache aging logic
i40e/i40evf: Update DESC_NEEDED value to reflect larger value
bnxt_en: cleanup DIM work on device shutdown
...
Async crypto accelerators (e.g. drivers/crypto/caam) support offloading
GCM operation. If they are enabled, crypto_aead_encrypt() return error
code -EINPROGRESS. In this case tls_do_encryption() needs to wait on a
completion till the time the response for crypto offload request is
received.
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
Pull locking updates from Ingo Molnar:
"The main changes relate to making lock_is_held() et al (and external
wrappers of them) work on const data types - this requires const
propagation through the depths of lockdep.
This removes a number of ugly type hacks the external helpers used"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
lockdep: Convert some users to const
lockdep: Make lockdep checking constant
lockdep: Assign lock keys on registration
Introduce a new qdisc ops ->change_tx_queue_len() so that
each qdisc could decide how to implement this if it wants.
Previously we simply read dev->tx_queue_len, after pfifo_fast
switches to skb array, we need this API to resize the skb array
when we change dev->tx_queue_len.
To avoid handling race conditions with TX BH, we need to
deactivate all TX queues before change the value and bring them
back after we are done, this also makes implementation easier.
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2018-01-26
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) A number of extensions to tcp-bpf, from Lawrence.
- direct R or R/W access to many tcp_sock fields via bpf_sock_ops
- passing up to 3 arguments to bpf_sock_ops functions
- tcp_sock field bpf_sock_ops_cb_flags for controlling callbacks
- optionally calling bpf_sock_ops program when RTO fires
- optionally calling bpf_sock_ops program when packet is retransmitted
- optionally calling bpf_sock_ops program when TCP state changes
- access to tclass and sk_txhash
- new selftest
2) div/mod exception handling, from Daniel.
One of the ugly leftovers from the early eBPF days is that div/mod
operations based on registers have a hard-coded src_reg == 0 test
in the interpreter as well as in JIT code generators that would
return from the BPF program with exit code 0. This was basically
adopted from cBPF interpreter for historical reasons.
There are multiple reasons why this is very suboptimal and prone
to bugs. To name one: the return code mapping for such abnormal
program exit of 0 does not always match with a suitable program
type's exit code mapping. For example, '0' in tc means action 'ok'
where the packet gets passed further up the stack, which is just
undesirable for such cases (e.g. when implementing policy) and
also does not match with other program types.
After considering _four_ different ways to address the problem,
we adapt the same behavior as on some major archs like ARMv8:
X div 0 results in 0, and X mod 0 results in X. aarch64 and
aarch32 ISA do not generate any traps or otherwise aborts
of program execution for unsigned divides.
Given the options, it seems the most suitable from
all of them, also since major archs have similar schemes in
place. Given this is all in the realm of undefined behavior,
we still have the option to adapt if deemed necessary.
3) sockmap sample refactoring, from John.
4) lpm map get_next_key fixes, from Yonghong.
5) test cleanups, from Alexei and Prashant.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2018-01-26
One last patch for this development cycle:
1) Add ESN support for IPSec HW offload.
From Yossef Efraim.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds a new uapi header file, erspan.h, and moves
the 'struct erspan_metadata' from internal erspan.h to it.
Signed-off-by: William Tu <u9012063@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Originally the erspan fields are defined as a group into a __be16 field,
and use mask and offset to access each field. This is more costly due to
calling ntohs/htons. The patch changes it to use bitfields.
Signed-off-by: William Tu <u9012063@gmail.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Very few (mlxsw) upstream drivers seem to allow offload of chains
other than 0. Save driver developers typing and add a helper for
checking both if ethtool's TC offload flag is on and if chain is 0.
This helper will set the extack appropriately in both error cases.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for passing up to 4 arguments to sock_ops bpf functions. It
reusues the reply union, so the bpf_sock_ops structures are not
increased in size.
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
This patch adds a macro, SOCK_OPS_SET_FIELD, for writing to
struct tcp_sock or struct sock fields. This required adding a new
field "temp" to struct bpf_sock_ops_kern for temporary storage that
is used by sock_ops_convert_ctx_access. It is used to store and recover
the contents of a register, so the register can be used to store the
address of the sk. Since we cannot overwrite the dst_reg because it
contains the pointer to ctx, nor the src_reg since it contains the value
we want to store, we need an extra register to contain the address
of the sk.
Also adds the macro SOCK_OPS_GET_OR_SET_FIELD that calls one of the
GET or SET macros depending on the value of the TYPE field.
Signed-off-by: Lawrence Brakmo <brakmo@fb.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Some dst_ops (e.g. md_dst_ops)) doesn't set this handler. It may result to:
"BUG: unable to handle kernel NULL pointer dereference at (null)"
Let's add a helper to check if update_pmtu is available before calling it.
Fixes: 52a589d51f ("geneve: update skb dst pmtu on tx path")
Fixes: a93bf0ff44 ("vxlan: update skb dst pmtu on tx path")
CC: Roman Kapl <code@rkapl.cz>
CC: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a tcp socket is closed, if it detects that its net namespace is
exiting, close immediately and do not wait for FIN sequence.
For normal sockets, a reference is taken to their net namespace, so it will
never exit while the socket is open. However, kernel sockets do not take a
reference to their net namespace, so it may begin exiting while the kernel
socket is still open. In this case if the kernel socket is a tcp socket,
it will stay open trying to complete its close sequence. The sock's dst(s)
hold a reference to their interface, which are all transferred to the
namespace's loopback interface when the real interfaces are taken down.
When the namespace tries to take down its loopback interface, it hangs
waiting for all references to the loopback interface to release, which
results in messages like:
unregister_netdevice: waiting for lo to become free. Usage count = 1
These messages continue until the socket finally times out and closes.
Since the net namespace cleanup holds the net_mutex while calling its
registered pernet callbacks, any new net namespace initialization is
blocked until the current net namespace finishes exiting.
After this change, the tcp socket notices the exiting net namespace, and
closes immediately, releasing its dst(s) and their reference to the
loopback interface, which lets the net namespace continue exiting.
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1711407
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=97811
Signed-off-by: Dan Streetman <ddstreet@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
