commit 44a182b9d1 upstream.
KASAN found a use-after-free in xhci_free_virt_device+0x33b/0x38e
where xhci_free_virt_device() sets slot id to 0 if udev exists:
if (dev->udev && dev->udev->slot_id)
dev->udev->slot_id = 0;
dev->udev will be true even if udev is freed because dev->udev is
not set to NULL.
set dev->udev pointer to NULL in xhci_free_dev()
The original patch went to stable so this fix needs to be applied
there as well.
Fixes: a400efe455 ("xhci: zero usb device slot_id member when disabling and freeing a xhci slot")
Cc: <stable@vger.kernel.org>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit bde0716d1f ]
For AMD Promontory xHCI host, although you can disable USB ports in
BIOS settings, those ports will be enabled anyway after you remove a
device on that port and re-plug it in again. It's a known limitation of
the chip. As a workaround we can clear the PORT_WAKE_BITS.
[commit and code comment rephrasing -Mathias]
Signed-off-by: Joe Lee <asmt.swfae@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0ee78c1014 ]
xhci driver displays the supported xHC USB revision in a message during
driver load:
"Host supports USB 3.1 Enhanced SuperSpeed"
Get the USB minor revision number from the xhci protocol capability.
This will show the correct supported revisions for new USB 3.2 and later
hosts
Don't rely on the SBRN (serial bus revision number) register, it's often
showing 0x30 (USB3.0) for hosts that support USB 3.1
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a400efe455 ]
set udev->slot_id to zero when disabling and freeing the xhci slot.
Prevents usb core from calling xhci with a stale slot id.
xHC controller may be reset during resume to recover from some error.
All slots are unusable as they are disabled and freed.
xhci driver starts slot enumeration again from 1 in the order they are
enabled. In the worst case a stale udev->slot_id for one device matches
a newly enabled slot_id for a different device, causing us to
perform a action on the wrong device.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d56e57ca03 ]
This patch reverts the commit 835e4241e7 ("usb: host: xhci-plat:
enable clk in resume timing") because this driver also has runtime PM
and the commit 560869100b ("clk: renesas: cpg-mssr: Restore module
clocks during resume") will restore the clock on R-Car H3 environment.
If the xhci_plat_suspend() disables the clk, the system cannot enable
the clk in resume like the following behavior:
< In resume >
- genpd_resume_noirq() runs and enable the clk (enable_count = 1)
- cpg_mssr_resume_noirq() restores the clk register.
-- Since the clk was disabled in suspend, cpg_mssr_resume_noirq()
will disable the clk and keep the enable_count.
- Even if xhci_plat_resume() calls clk_prepare_enable(), since
the enable_count is 1, the clk will be not enabled.
After this patch is applied, the cpg-mssr driver will save the clk
as enable, so the clk will be enabled in resume.
Fixes: 835e4241e7 ("usb: host: xhci-plat: enable clk in resume timing")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 621faf4f6a upstream.
The Dell Inspiron 5775 is a Raven Ridge. The Enable Slot command timed
out when a USB device gets plugged:
[ 212.156326] xhci_hcd 0000:03:00.3: Error while assigning device slot ID
[ 212.156340] xhci_hcd 0000:03:00.3: Max number of devices this xHCI host supports is 64.
[ 212.156348] usb usb2-port3: couldn't allocate usb_device
AMD suggests that a delay before xHC suspends can fix the issue.
I can confirm it fixes the issue, so use the suspend delay quirk for
Raven Ridge's xHC.
Cc: stable@vger.kernel.org
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cd3f1790b0 upstream.
xhci_disable_slot() allows the invoker to pass a command pointer
as paramenter. Otherwise, it will allocate one. This will cause
memory leak when a command structure was allocated inside of this
function while queuing command trb fails. Another problem comes up
when the invoker passed a command pointer, but xhci_disable_slot()
frees it when it detects a dead host.
This patch fixes these two problems by removing the command parameter
from xhci_disable_slot().
Fixes: f9e609b824 ("usb: xhci: Add helper function xhci_disable_slot().")
Cc: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b64149ca01 upstream.
xhci_disable_slot() is a helper for disabling a slot when a device
goes away or recovers from error situations. Currently, it checks
the corespoding virt-dev pointer and returns directly (w/o issuing
disable slot command) if it's null.
This is unnecessary and will cause problems in case where virt-dev
allocation fails and xhci_disable_slot() is called to roll back the
hardware state. Refer to the implementation of xhci_alloc_dev().
This patch removes lines to check virt-dev in xhci_disable_slot().
Fixes: f9e609b824 ("usb: xhci: Add helper function xhci_disable_slot().")
Cc: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 191edc5e2e upstream.
When a USB device gets plugged on ASUS PRIME B350M-A's front ports, the
xHC stops working:
[ 549.114587] xhci_hcd 0000:02:00.0: WARN: xHC CMD_RUN timeout
[ 549.114608] suspend_common(): xhci_pci_suspend+0x0/0xc0 returns -110
[ 549.114638] xhci_hcd 0000:02:00.0: can't suspend (hcd_pci_runtime_suspend returned -110)
Delay before running xHC command CMD_RUN can workaround the issue.
Use a new quirk to make the delay only targets to the affected xHC.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 02a10f061a upstream.
commit a8c06e407e ("usb: separate out sysdev pointer from usb_bus")
converted to use hcd->self.sysdev for DMA operations instead of
hcd->self.controller, but forgot to do it for hcd test mode. Replace
the correct one in this commit.
Fixes: a8c06e407e ("usb: separate out sysdev pointer from usb_bus")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 46408ea558 upstream.
There is a race condition between finish_unlinks->finish_urb() function
and usb_kill_urb() in ohci controller case. The finish_urb calls
spin_unlock(&ohci->lock) before usb_hcd_giveback_urb() function call,
then if during this time, usb_kill_urb is called for another endpoint,
then new ed will be added to ed_rm_list at beginning for unlink, and
ed_rm_list will point to newly added.
When finish_urb() is completed in finish_unlinks() and ed->td_list
becomes empty as in below code (in finish_unlinks() function):
if (list_empty(&ed->td_list)) {
*last = ed->ed_next;
ed->ed_next = NULL;
} else if (ohci->rh_state == OHCI_RH_RUNNING) {
*last = ed->ed_next;
ed->ed_next = NULL;
ed_schedule(ohci, ed);
}
The *last = ed->ed_next will make ed_rm_list to point to ed->ed_next
and previously added ed by usb_kill_urb will be left unreferenced by
ed_rm_list. This causes usb_kill_urb() hang forever waiting for
finish_unlink to remove added ed from ed_rm_list.
The main reason for hang in this race condtion is addition and removal
of ed from ed_rm_list in the beginning during usb_kill_urb and later
last* is modified in finish_unlinks().
As suggested by Alan Stern, the solution for proper handling of
ohci->ed_rm_list is to remove ed from the ed_rm_list before finishing
any URBs. Then at the end, we can add ed back to the list if necessary.
This properly handle the updated ohci->ed_rm_list in usb_kill_urb().
Fixes: 977dcfdc60 ("USB: OHCI: don't lose track of EDs when a controller dies")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Aman Deep <aman.deep@samsung.com>
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b2685bdacd upstream.
Running io_watchdog_func() while ohci_urb_enqueue() is running can
cause a race condition where ohci->prev_frame_no is corrupted and the
watchdog can mis-detect following error:
ohci-platform 664a0800.usb: frame counter not updating; disabled
ohci-platform 664a0800.usb: HC died; cleaning up
Specifically, following scenario causes a race condition:
1. ohci_urb_enqueue() calls spin_lock_irqsave(&ohci->lock, flags)
and enters the critical section
2. ohci_urb_enqueue() calls timer_pending(&ohci->io_watchdog) and it
returns false
3. ohci_urb_enqueue() sets ohci->prev_frame_no to a frame number
read by ohci_frame_no(ohci)
4. ohci_urb_enqueue() schedules io_watchdog_func() with mod_timer()
5. ohci_urb_enqueue() calls spin_unlock_irqrestore(&ohci->lock,
flags) and exits the critical section
6. Later, ohci_urb_enqueue() is called
7. ohci_urb_enqueue() calls spin_lock_irqsave(&ohci->lock, flags)
and enters the critical section
8. The timer scheduled on step 4 expires and io_watchdog_func() runs
9. io_watchdog_func() calls spin_lock_irqsave(&ohci->lock, flags)
and waits on it because ohci_urb_enqueue() is already in the
critical section on step 7
10. ohci_urb_enqueue() calls timer_pending(&ohci->io_watchdog) and it
returns false
11. ohci_urb_enqueue() sets ohci->prev_frame_no to new frame number
read by ohci_frame_no(ohci) because the frame number proceeded
between step 3 and 6
12. ohci_urb_enqueue() schedules io_watchdog_func() with mod_timer()
13. ohci_urb_enqueue() calls spin_unlock_irqrestore(&ohci->lock,
flags) and exits the critical section, then wake up
io_watchdog_func() which is waiting on step 9
14. io_watchdog_func() enters the critical section
15. io_watchdog_func() calls ohci_frame_no(ohci) and set frame_no
variable to the frame number
16. io_watchdog_func() compares frame_no and ohci->prev_frame_no
On step 16, because this calling of io_watchdog_func() is scheduled on
step 4, the frame number set in ohci->prev_frame_no is expected to the
number set on step 3. However, ohci->prev_frame_no is overwritten on
step 11. Because step 16 is executed soon after step 11, the frame
number might not proceed, so ohci->prev_frame_no must equals to
frame_no.
To address above scenario, this patch introduces a special sentinel
value IO_WATCHDOG_OFF and set this value to ohci->prev_frame_no when
the watchdog is not pending or running. When ohci_urb_enqueue()
schedules the watchdog (step 4 and 12 above), it compares
ohci->prev_frame_no to IO_WATCHDOG_OFF so that ohci->prev_frame_no is
not overwritten while io_watchdog_func() is running.
Signed-off-by: Shigeru Yoshida <Shigeru.Yoshida@windriver.com>
Signed-off-by: Haiqing Bai <Haiqing.Bai@windriver.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec897569ad upstream.
Move the Kconfig symbols USB_UHCI_BIG_ENDIAN_MMIO and
USB_UHCI_BIG_ENDIAN_DESC out of drivers/usb/host/Kconfig, which is
conditional upon USB && USB_SUPPORT, so that it can be freely selected
by platform Kconfig symbols in architecture code.
For example once the MIPS_GENERIC platform selects are fixed in commit
2e6522c565 ("MIPS: Fix typo BIG_ENDIAN to CPU_BIG_ENDIAN"), the MIPS
32r6_defconfig warns like so:
warning: (MIPS_GENERIC) selects USB_UHCI_BIG_ENDIAN_MMIO which has unmet direct dependencies (USB_SUPPORT && USB)
warning: (MIPS_GENERIC) selects USB_UHCI_BIG_ENDIAN_DESC which has unmet direct dependencies (USB_SUPPORT && USB)
Fixes: 2e6522c565 ("MIPS: Fix typo BIG_ENDIAN to CPU_BIG_ENDIAN")
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Corentin Labbe <clabbe.montjoie@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-mips@linux-mips.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patchwork: https://patchwork.linux-mips.org/patch/18559/
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da99706689 upstream.
When plugging in a USB webcam I see the following message:
xhci_hcd 0000:04:00.0: WARN Successful completion on short TX: needs
XHCI_TRUST_TX_LENGTH quirk?
handle_tx_event: 913 callbacks suppressed
All is quiet again with this patch (and I've done a fair but of soak
testing with the camera since).
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d9b70f7d5 upstream.
Avoid null pointer dereference if some function is walking through the
devs array accessing members of a new virt_dev that is mid allocation.
Add the virt_dev to xhci->devs[i] _after_ the virt_device and all its
members are properly allocated.
issue found by KASAN: null-ptr-deref in xhci_find_slot_id_by_port
"Quick analysis suggests that xhci_alloc_virt_device() is not mutex
protected. If so, there is a time frame where xhci->devs[slot_id] is set
but not fully initialized. Specifically, xhci->devs[i]->udev can be NULL."
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72b663a99c upstream.
For MTK's xHCI 1.0 or latter, TD size is the number of max
packet sized packets remaining in the TD, not including
this TRB (following spec).
For MTK's xHCI 0.96 and older, TD size is the number of max
packet sized packets remaining in the TD, including this TRB
(not following spec).
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d5a31582e upstream.
The variable temp is incorrectly being updated, instead it should
be offset otherwise the loop just reads the same capability value
and loops forever. Thanks to Alan Stern for pointing out the
correct fix to my original fix. Fix also cleans up clang warning:
drivers/usb/host/ehci-dbg.c:840:4: warning: Value stored to 'temp'
is never read
Fixes: d49d431744 ("USB: misc ehci updates")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4ec40ec4b upstream.
xHC can generate two events for a short transfer if the short TRB and
last TRB in the TD are not the same TRB.
The driver will handle the TD after the first short event, and remove
it from its internal list. Driver then incorrectly prints a warning
for the second event:
"WARN Event TRB for slot x ep y with no TDs queued"
Fix this by not printing a warning if we get a event on a empty list
if the previous event was a short event.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dcabc76fa9 ]
xhci_disable_slot() is a helper for disabling a slot when a device
goes away or recovers from error situations. Currently, it returns
success when it sees a dead host. This is not the right way to go.
It should return error and let the invoker know that disable slot
command was failed due to a dead host.
Fixes: f9e609b824 ("usb: xhci: Add helper function xhci_disable_slot().")
Cc: Guoqing Zhang <guoqing.zhang@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci_stop_device() calls xhci_queue_stop_endpoint() multiple times
without checking the return value. xhci_queue_stop_endpoint() can
return error if the HC is already halted or unable to queue commands.
This can cause a deadlock condition as xhci_stop_device() would
end up waiting indefinitely for a completion for the command that
didn't get queued. Fix this by checking the return value and bailing
out of xhci_stop_device() in case of error. This patch happens to fix
potential memory leaks of the allocated command structures as well.
Fixes: c311e391a7 ("xhci: rework command timeout and cancellation,")
Cc: <stable@vger.kernel.org>
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KASAN reported use-after-free bug when xhci host controller died:
[ 176.952537] BUG: KASAN: use-after-free in xhci_handle_command_timeout+0x68/0x224
[ 176.960846] Write of size 4 at addr ffffffc0cbb01608 by task kworker/3:3/1680
...
[ 177.180644] Freed by task 0:
[ 177.183882] kasan_slab_free+0x90/0x15c
[ 177.188194] kfree+0x114/0x28c
[ 177.191630] xhci_cleanup_command_queue+0xc8/0xf8
[ 177.196916] xhci_hc_died+0x84/0x358
Problem here is that when the cmd_timer fired, it would try to access
current_cmd while the command queue is already freed by xhci_hc_died().
Cleanup current_cmd in xhci_cleanup_command_queue() to avoid that.
Fixes: d9f11ba9f1 ("xhci: Rework how we handle unresponsive or hoptlug removed hosts")
Cc: <stable@vger.kernel.org> # v4.12+
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many USB 3.1 capable hosts never updated the Serial Bus Release Number
(SBRN) register to USB 3.1 from USB 3.0
xhci driver identified USB 3.1 capable hosts based on this SBRN register,
which according to specs "contains the release of the Universal Serial
Bus Specification with which this Universal Serial Bus Host Controller
module is compliant." but still in october 2017 gives USB 3.0 as
the only possible option.
Make an additional check for USB 3.1 support and enable it if the xHCI
supported protocol capablity lists USB 3.1 capable ports.
Cc: <stable@vger.kernel.org> # v4.6+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit dec08194ff.
Commit dec08194ff ("xhci: Limit USB2 port wake support for AMD Promontory
hosts") makes all high speed USB ports on ASUS PRIME B350M-A cease to
function after enabling runtime PM.
All boards with this chipsets will be affected, so revert the commit.
The original patch was added to stable 4.9, 4.11 and 4.12 and needs
to reverted from there as well
Cc: <stable@vger.kernel.org> # 4.9+
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A SuperSpeedPlus roothub needs to have the Link Protocol (LP) bit set in
the bmSublinkSpeedAttr[] entry of a SuperSpeedPlus descriptor.
If the xhci controller has an optional Protocol Speed ID (PSI) table then
that will be used as a base to create the roothub SuperSpeedPlus
descriptor.
The PSI table does not however necessary contain the LP bit so we need
to set it manually.
Check the psi speed and set LP bit if speed is 10Gbps or higher.
We're not setting it for 5 to 10Gbps as USB 3.1 specification always
mention SuperSpeedPlus for 10Gbps or higher, and some SSIC USB 3.0 speeds
can be over 5Gbps, such as SSIC-G3B-L1 at 5830 Mbps
Cc: <stable@vger.kernel.org> # 4.6+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The flow control workaround for ASM1042A xHC hosts sleeps between
register polling. The workaround gets called in several places, among
them with spin_lock_irq() held when xHC host is resumed or hoplug removed.
This was noticed as kernel panics at resume on a Dell XPS15 9550 with
TB16 thunderbolt dock.
Avoid sleeping with spin_lock_irq() held, use udelay() instead
The original workaround was added to 4.9 and 4.12 stable releases,
this patch needs to be applied to those as well.
Fixes: 9da5a1092b ("xhci: Bad Ethernet performance plugged in ASM1042A host")
Cc: <stable@vger.kernel.org> #4.9+
Reported-by: Jose Marino <marinoj@nso.edu>
Tested-by: Jose Marino <marinoj@nso.edu>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4c39d4b949 ("usb: xhci: use bus->sysdev for DMA configuration")
updated the method determining DMA for XHCI from sysdev. However, this
patch broke the ability to enumerate the FWNODE from parent ACPI devices
from the child plat XHCI device.
Currently, xhci_plat is not set up properly when the parent device is an
ACPI node. The conditions that xhci_plat_probe should satisfy are
1. xhci_plat comes from firmware
2. xhci_plat is child of a device from firmware (dwc3-plat)
3. xhci_plat is grandchild of a pci device (dwc3-pci)
Case 2 is covered when the child is an OF node (by checking
sysdev->parent->of_node), however, an ACPI parent will return NULL in
the of_node check and will thus not result in sysdev being set to
sysdev->parent
[ 17.591549] xhci-hcd: probe of xhci-hcd.6.auto failed with error -5
This change adds a check for ACPI to completely allow for condition 2.
This is done by first checking if the parent node is of type ACPI (e.g.,
dwc3-plat) and set sysdev to sysdev->parent if either of the two
following conditions are met:
1: If fwnode is empty (in the case that platform_device_add_properties
was not called on the allocated platform device)
2: fwnode exists but is not of type ACPI (this would happen if
platform_device_add_properties was called on the allocated device.
Instead of type FWNODE_ACPI, you would end up with FWNODE_PDATA)
Cc: stable@vger.kernel.org #4.12.x
Cc: stable@vger.kernel.org #4.13.x
Fixes: 4c39d4b949 ("usb: xhci: use bus->sysdev for DMA configuration")
Tested-by: Thang Q. Nguyen <tqnguyen@apm.com>
Signed-off-by: Adam Wallis <awallis@codeaurora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Read the endpiont ESIT from endpiont context using correct macro.
Add a macro for reading the high bits of ESIT for Large ESIT Payload
Capable hosts (LEC=1)
Cc: <stable@vger.kernel.org> # 4.12
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Servers were emitting failed handoff messages but were not
waiting the full 1 second as designated in section 4.22.1 of
the eXtensible Host Controller Interface specifications. The
handshake was using wrong units so calls were made with milliseconds
not microseconds. Comments referenced 5 seconds not 1 second as
in specs.
The wrong units were also corrected in a second handshake call.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jim Dickerson <jim.dickerson@hpe.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci driver keeps a bus_state structure for each hcd (usb2 and usb3)
The structure is picked based on hcd speed, but driver only compared
for HCD_USB3 speed, returning the wrong bus_state for HCD_USB31 hosts.
This caused null pointer dereference errors in bus_resume function.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the xhci_add_endpoint(), a new ring was allocated and saved at
xhci_virt_ep->new_ring. Hence, when error happens, we need to free
the allocated ring before returning error.
Current code frees xhci_virt_ep->ring instead of the new_ring. This
patch fixes this.
Cc: <stable@vger.kernel.org>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull dma-mapping updates from Christoph Hellwig:
- removal of the old dma_alloc_noncoherent interface
- remove unused flags to dma_declare_coherent_memory
- restrict OF DMA configuration to specific physical busses
- use the iommu mailing list for dma-mapping questions and patches
* tag 'dma-mapping-4.14' of git://git.infradead.org/users/hch/dma-mapping:
dma-coherent: fix dma_declare_coherent_memory() logic error
ARM: imx: mx31moboard: Remove unused 'dma' variable
dma-coherent: remove an unused variable
MAINTAINERS: use the iommu list for the dma-mapping subsystem
dma-coherent: remove the DMA_MEMORY_MAP and DMA_MEMORY_IO flags
dma-coherent: remove the DMA_MEMORY_INCLUDES_CHILDREN flag
of: restrict DMA configuration
dma-mapping: remove dma_alloc_noncoherent and dma_free_noncoherent
i825xx: switch to switch to dma_alloc_attrs
au1000_eth: switch to dma_alloc_attrs
sgiseeq: switch to dma_alloc_attrs
dma-mapping: reduce dma_mapping_error inline bloat
Pull MFD updates from Lee Jones:
"New Drivers
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
New Device Support:
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
New Functionality:
- Amend API to provide register layout; atmel-smc
Fix-ups:
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
Bug Fixes:
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll"
* tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (61 commits)
mfd: intel_soc_pmic: Differentiate between Bay and Cherry Trail CRC variants
mfd: intel_soc_pmic: Export separate mfd-cell configs for BYT and CHT
dt-bindings: mfd: Add bindings for ZII RAVE devices
mfd: omap-usb-tll: Fix register offsets
mfd: da9052: Constify spi_device_id
mfd: intel-lpss: Put I2C and SPI controllers into reset state on suspend
mfd: da9055: Constify i2c_device_id
mfd: intel-lpss: Add missing PCI ID for Intel Sunrise Point LPSS devices
mfd: t7l66xb: Handle return value of clk_prepare_enable
mfd: Add ROHM BD9571MWV-M PMIC DT bindings
mfd: intel_soc_pmic_chtwc: Turn Kconfig option into a bool
mfd: lp87565: Convert to use devm_mfd_add_devices()
mfd: Add support for TPS68470 device
mfd: lpc_ich: Do not touch SPI-NOR write protection bit on Haswell/Broadwell
mfd: syscon: atmel-smc: Add helper to retrieve register layout
mfd: axp20x: Use correct platform device ID for many PEK
dt-bindings: mfd: axp20x: Introduce bindings for AXP813
mfd: axp20x: Add support for AXP813 PMIC
dt-bindings: mfd: axp20x: Add AXP806 to supported list of chips
mfd: Add ROHM BD9571MWV-M MFD PMIC driver
...
DMA_MEMORY_IO was never used in the tree, so remove it. That means there is
no need for the DMA_MEMORY_MAP flag either now, so remove it as well and
change dma_declare_coherent_memory to return a normal errno value.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Make this structure const as it is not modified. And replace __initdata
with __initconst to avoid section conflict error.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The xhci-mtk driver is a generic driver for MediaTek xHCI IP, add
a generic compatible to avoid confusion when support new SoCs but
use a compatible with specific SoC's name "mt8173".
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To perform SuperSpeed compliance testing the port should first
be placed into compliance mode. For xHCI 1.0 and prior this
transition happens automatically when the port is in Training
and encounters an LFPS timeout. Thus running compliance tests
against a test appliance may simply just work by simply plugging
in to the downstream port.
However starting with xHCI 1.1 the transition from Polling.LFPS
to compliance mode may be disabled by default and needs to be
explicitly enabled by writing to the PLS field of the PORTSC
register, which sets an internal 'CTE' (Compliance Transition
Enabled) flag so that the port will perform the transition the
next time it encounters LFPS timeout. Whether this is disabled or
not is determined by the 'CTC' (Compliance Transition Capability)
bit in the HCCPARAMS2 capability register.
In order to allow a test operator to change this if needed, allow
a test driver (such as drivers/usb/misc/lvstest.c) to send a
SET_FEATURE(PORT_LINK_STATE) control message to the root hub to
update the link state prior to connecting to the port. Subsequently,
placing the port in warm reset would then disable the flag.
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following commit cause a regression on ATI chipsets.
'commit e788787ef4 ("usb:xhci:Add quirk for Certain
failing HP keyboard on reset after resume")'
This causes pinfo->smbus_dev to be wrongly set to NULL on
systems with the ATI chipset that this function checks for first.
Added conditional check for AMD chipsets to avoid the overwriting
pinfo->smbus_dev.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: e788787ef4 ("usb:xhci:Add quirk for Certain
failing HP keyboard on reset after resume")
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
cc: <stable@vger.kernel.org>
Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bus_resume() tried to resume the same ports the bus_suspend()
suspeded. This caused PLC timeouts in case a suspended device disconnected
and was not in a resumable state at bus_resume().
Add a check to make sure the link state is either U3 or resuming
before actually resuming the link.
At the same time do some other changes such as make sure we remove
wake on connect/disconnect/overcurrent also for the resuming ports,
and avoid extra portsc port register writes.
This improves resume time with 10ms in those PLC timeout cases where
devices disconnect at suspend/resume cycle.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
temp and temp1 variables are used for port status (portsc) and
command register. Give them more descriptive names
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
