Pull drm fixes from Dave Airlie:
"Fixes built up over the past 1.5 weeks or so, it's two weeks of
amdgpu, some core cleanups and some panfrost fixes. I also finally
figured out why my desktop was slow to do a bunch of stuff (someone
gave it an IPv6 address which can't reach anything!).
core:
- Some cleanups and fixes in the self-refresh helpers
- Some cleanups and fixes in the atomic helpers
amdgpu:
- Fix a 64 bit divide
- Prevent a memory leak in a failure case in dc
- Load proper gfx firmware on navi14 variants
- Add more navi12 and navi14 PCI ids
- Misc fixes for renoir
- Fix bandwidth issues with multiple displays on vega20
- Support for Dali
- Fix a possible oops with KFD on hawaii
- Fix for backlight level after resume on some APUs
- Other misc fixes
panfrost:
- Multiple panfrost fixes for regulator support and page fault
handling"
* tag 'drm-next-2019-09-27' of git://anongit.freedesktop.org/drm/drm: (34 commits)
drm/amd/display: prevent memory leak
drm/amdgpu/gfx10: add support for wks firmware loading
drm/amdgpu/display: include slab.h in dcn21_resource.c
drm/amdgpu/display: fix 64 bit divide
drm/panfrost: Prevent race when handling page fault
drm/panfrost: Remove NULL checks for regulator
drm/panfrost: Fix regulator_get_optional() misuse
drm: Measure Self Refresh Entry/Exit times to avoid thrashing
drm: Fix kerneldoc and remove unused struct member in self_refresh helper
drm/atomic: Rename crtc_state->pageflip_flags to async_flip
drm/atomic: Reject FLIP_ASYNC unconditionally
drm/atomic: Take the atomic toys away from X
drm/amdgpu: flag navi12 and 14 as experimental for 5.4
drm/kms: Duct-tape for mode object lifetime checks
drm/amdgpu: add navi12 pci id
drm/amdgpu: add navi14 PCI ID for work station SKU
drm/amdkfd: Swap trap temporary registers in gfx10 trap handler
drm/amd/powerplay: implement sysfs for getting dpm clock
drm/amd/display: Restore backlight brightness after system resume
drm/amd/display: Implement voltage limitation for dali
...
Pull i2c updates from Wolfram Sang:
- new driver for ICY, an Amiga Zorro card :)
- axxia driver gained slave mode support, NXP driver gained ACPI
- the slave EEPROM backend gained 16 bit address support
- and lots of regular driver updates and reworks
* 'i2c/for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (52 commits)
i2c: tegra: Move suspend handling to NOIRQ phase
i2c: imx: ACPI support for NXP i2c controller
i2c: uniphier(-f): remove all dev_dbg()
i2c: uniphier(-f): use devm_platform_ioremap_resource()
i2c: slave-eeprom: Add comment about address handling
i2c: exynos5: Remove IRQF_ONESHOT
i2c: stm32f7: Make structure stm32f7_i2c_algo constant
i2c: cht-wc: drop check because i2c_unregister_device() is NULL safe
i2c-eeprom_slave: Add support for more eeprom models
i2c: fsi: Add of_put_node() before break
i2c: synquacer: Make synquacer_i2c_ops constant
i2c: hix5hd2: Remove IRQF_ONESHOT
i2c: i801: Use iTCO version 6 in Cannon Lake PCH and beyond
watchdog: iTCO: Add support for Cannon Lake PCH iTCO
i2c: iproc: Make bcm_iproc_i2c_quirks constant
i2c: iproc: Add full name of devicetree node to adapter name
i2c: piix4: Add ACPI support
i2c: piix4: Fix probing of reserved ports on AMD Family 16h Model 30h
i2c: ocores: use request_any_context_irq() to register IRQ handler
i2c: designware: Fix optional reset error handling
...
This reverts commit 83f35bc3a8.
There are at least two DSI controller drivers which relies on the old
behaviour of adv7511 driver. To avoid platform breakage this patch
should be reverted. This is a temporary solution, as it blocks adv7511
usage with other platforms.
Assumption that DSI device driver (bridge/panel) should first expose
drm_bridge/drm_panel object, then look for DSI bus is just incorrect -
it can work with devices controlled via i2c but it cannot work with
devices controlled via DSI - they will not be able to probe.
To solve the issue following steps should be performed:
- rework reverted patch allowing co-operation with broken DSI controller
drivers - with simple/ugly workaround,
- fix controller drivers and then remove workaround.
Signed-off-by: Rob Clark <robdclark@chromium.org>
[a.hajda: changed commit message]
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190829180836.14453-1-robdclark@gmail.com
In the general move to have i2c_new_*_device functions which return
ERR_PTR instead of NULL, this patch converts i2c_new_secondary_device().
There are only few users, so this patch converts the I2C core and all
users in one go. The function gets renamed to i2c_new_ancillary_device()
so out-of-tree users will get a build failure to understand they need to
adapt their error checking code.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> # adv748x
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> # adv7511 + adv7604
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # adv7604
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In contrast to all of the DSI panel drivers in drivers/gpu/drm/panel
which attach to the DSI host via mipi_dsi_attach() at probe time, the
ADV7533 bridge device does not. Instead it defers this to the point that
the upstream device connects to its bridge via drm_bridge_attach().
The generic Synopsys MIPI DSI host driver does not register it's own
drm_bridge until the MIPI DSI has attached. But it does not call
drm_bridge_attach() on the downstream device until the upstream device
has attached. This leads to a chicken and the egg failure and the DRM
pipeline does not complete.
Since all other mipi_dsi_device drivers call mipi_dsi_attach() in
probe(), make the adv7533 mipi_dsi_device do the same. This ensures that
the Synopsys MIPI DSI host registers it's bridge such that it is
available for the upstream device to connect to.
Signed-off-by: Matt Redfearn <matt.redfearn@thinci.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190627151740.2277-1-matt.redfearn@thinci.com
Maarten needs -rc4 backmerged so he can pull in the fbcon notifier
removal topic branch into drm-misc-next.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The driver currently sets register 0xfb (Low Refresh Rate) based on the
value of mode->vrefresh. Firstly, this field is specified to be in Hz,
but the magic numbers used by the code are Hz * 1000. This essentially
leads to the low refresh rate always being set to 0x01, since the
vrefresh value will always be less than 24000. Fix the magic numbers to
be in Hz.
Secondly, according to the comment in drm_modes.h, the field is not
supposed to be used in a functional way anyway. Instead, use the helper
function drm_mode_vrefresh().
Fixes: 9c8af882bf ("drm: Add adv7511 encoder driver")
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Matt Redfearn <matt.redfearn@thinci.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190424132210.26338-1-matt.redfearn@thinci.com
The mode and ajusted_mode passed to the bridge .mode_set() operation
should never be modified by the bridge (and are not in any of the
existing bridge drivers). Make them const to make this clear.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 4.19.
Rob has some new hardware support for new qualcomm hw that I'll send
along separately. This has the display part of it, the remaining pull
is for the acceleration engine.
This also contains a wound-wait/wait-die mutex rework, Peter has acked
it for merging via my tree.
Otherwise mostly the usual level of activity. Summary:
core:
- Wound-wait/wait-die mutex rework
- Add writeback connector type
- Add "content type" property for HDMI
- Move GEM bo to drm_framebuffer
- Initial gpu scheduler documentation
- GPU scheduler fixes for dying processes
- Console deferred fbcon takeover support
- Displayport support for CEC tunneling over AUX
panel:
- otm8009a panel driver fixes
- Innolux TV123WAM and G070Y2-L01 panel driver
- Ilitek ILI9881c panel driver
- Rocktech RK070ER9427 LCD
- EDT ETM0700G0EDH6 and EDT ETM0700G0BDH6
- DLC DLC0700YZG-1
- BOE HV070WSA-100
- newhaven, nhd-4.3-480272ef-atxl LCD
- DataImage SCF0700C48GGU18
- Sharp LQ035Q7DB03
- p079zca: Refactor to support multiple panels
tinydrm:
- ILI9341 display panel
New driver:
- vkms - virtual kms driver to testing.
i915:
- Icelake:
Display enablement
DSI support
IRQ support
Powerwell support
- GPU reset fixes and improvements
- Full ppgtt support refactoring
- PSR fixes and improvements
- Execlist improvments
- GuC related fixes
amdgpu:
- Initial amdgpu documentation
- JPEG engine support on VCN
- CIK uses powerplay by default
- Move to using core PCIE functionality for gens/lanes
- DC/Powerplay interface rework
- Stutter mode support for RV
- Vega12 Powerplay updates
- GFXOFF fixes
- GPUVM fault debugging
- Vega12 GFXOFF
- DC improvements
- DC i2c/aux changes
- UVD 7.2 fixes
- Powerplay fixes for Polaris12, CZ/ST
- command submission bo_list fixes
amdkfd:
- Raven support
- Power management fixes
udl:
- Cleanups and fixes
nouveau:
- misc fixes and cleanups.
msm:
- DPU1 support display controller in sdm845
- GPU coredump support.
vmwgfx:
- Atomic modesetting validation fixes
- Support for multisample surfaces
armada:
- Atomic modesetting support completed.
exynos:
- IPPv2 fixes
- Move g2d to component framework
- Suspend/resume support cleanups
- Driver cleanups
imx:
- CSI configuration improvements
- Driver cleanups
- Use atomic suspend/resume helpers
- ipu-v3 V4L2 XRGB32/XBGR32 support
pl111:
- Add Nomadik LCDC variant
v3d:
- GPU scheduler jobs management
sun4i:
- R40 display engine support
- TCON TOP driver
mediatek:
- MT2712 SoC support
rockchip:
- vop fixes
omapdrm:
- Workaround for DRA7 errata i932
- Fix mm_list locking
mali-dp:
- Writeback implementation
PM improvements
- Internal error reporting debugfs
tilcdc:
- Single fix for deferred probing
hdlcd:
- Teardown fixes
tda998x:
- Converted to a bridge driver.
etnaviv:
- Misc fixes"
* tag 'drm-next-2018-08-15' of git://anongit.freedesktop.org/drm/drm: (1506 commits)
drm/amdgpu/sriov: give 8s for recover vram under RUNTIME
drm/scheduler: fix param documentation
drm/i2c: tda998x: correct PLL divider calculation
drm/i2c: tda998x: get rid of private fill_modes function
drm/i2c: tda998x: move mode_valid() to bridge
drm/i2c: tda998x: register bridge outside of component helper
drm/i2c: tda998x: cleanup from previous changes
drm/i2c: tda998x: allocate tda998x_priv inside tda998x_create()
drm/i2c: tda998x: convert to bridge driver
drm/scheduler: fix timeout worker setup for out of order job completions
drm/amd/display: display connected to dp-1 does not light up
drm/amd/display: update clk for various HDMI color depths
drm/amd/display: program display clock on cache match
drm/amd/display: Add NULL check for enabling dp ss
drm/amd/display: add vbios table check for enabling dp ss
drm/amd/display: Don't share clk source between DP and HDMI
drm/amd/display: Fix DP HBR2 Eye Diagram Pattern on Carrizo
drm/amd/display: Use calculated disp_clk_khz value for dce110
drm/amd/display: Implement custom degamma lut on dcn
drm/amd/display: Destroy aux_engines only once
...
The adv7511 driver keeps a private copy of the EDID in its driver state
struct. But this copy is only used in adv7511_get_modes() where it is also
retrieved, so there is no need to keep this extra copy around.
If a need to access the EDID elsewhere in the driver ever arises the copy
that is stored in the connector can be used. This copy is accessible
through drm_connector_get_edid().
Note, this patch removes the NULL check of the EDID before passing it to
drm_detect_hdmi_monitor(), but that is fine since the function correctly
handles the case where the EDID is NULL.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170905121018.11477-2-lars@metafoo.de
Currently adv7511_get_modes() bails out early when no EDID could be
retrieved. This leaves the previous EDID in place, which is typically not
the intended behavior and might confuse applications. Instead the EDID
should be cleared when no EDID could be retrieved.
All functions that are called after the EDID check handle the case where
the EDID is NULL just fine and exhibit the expected behavior, so just drop
the check.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20170905121018.11477-1-lars@metafoo.de
Make these const as they are only passed to the function
drm_connector_init and the corresponding argument is of type const.
Done using Coccinelle
@match disable optional_qualifier@
identifier s;
@@
static struct drm_connector_funcs s = {...};
@ref@
position p;
identifier match.s;
@@
s@p
@good1@
identifier match.s;
expression e1,e2;
position ref.p;
@@
drm_connector_init(e1,e2,&s@p,...)
@bad depends on !good1@
position ref.p;
identifier match.s;
@@
s@p
@depends on forall !bad disable optional_qualifier@
identifier match.s;
@@
static
+ const
struct drm_connector_funcs s;
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1502191712-11231-2-git-send-email-bhumirks@gmail.com
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Lower modes on ADV7533 require lower number of DSI lanes for correct
operation. If ADV7533 is being used with 4 DSI lanes, then switch the
lanes to 3 when the target mode's pixel clock is less than 80 Mhz.
Based on patch by Andy Green <andy.green@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
ADV7533 provides an internal timing generator for certain modes that it
can't use the DSI clock directly.
We've observed that HDMI is more stable with the internal timing
generator, especially if there are instabilities in the DSI clock source.
The data spec also seems to recommend the usage of the timing generator
for all modes.
However, on some platforms, it's reported that enabling the timing
generator causes instabilities with the HDMI output.
Create a DT parameter that lets a platform explicitly disable the timing
generator. The timing generator is enabled by default.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
In order to pass DSI specific parameters to the DSI host, we need the
driver to create a mipi_dsi_device DSI device that attaches to the
host.
Use of_graph helpers to get the DSI host DT node. Create a MIPI DSI
device using this host. Finally, attach this device to the DSI host.
Populate DT parameters (number of data lanes for now) that are required
for DSI RX to work correctly. Hardcode few other parameters (rgb,
embedded_sync) for now.
Select DRM_MIPI_DSI config option only when ADV7533 support is enabled.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
ADV7533 is a DSI to HDMI encoder chip. It is a derivative of ADV7511,
with additional blocks to translate input DSI data to parallel RGB
data. Besides the ADV7511 I2C register map, it has additional registers
that require to be configured to activate the DSI Rx block.
Create a new config that enables ADV7533 support. Use DT compatible
strings to populate the ADV7533 type enum. Add minimal register
configurations belonging to the DSI/CEC register map. Keep the ADV7533
code in a separate file.
Originally worked on by Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
When the adv7511 i2c client doesn't have an interrupt line, we observe a
deadlock on caused by trying to lock drm device's mode_config.mutex twice
in the same context.
Here is the sequence that causes it:
ioctl DRM_IOCTL_MODE_GETCONNECTOR from userspace
drm_mode_getconnector (acquires mode_config mutex)
connector->fill_modes()
drm_helper_probe_single_connector_modes
connector_funcs->get_modes
adv7511_encoder_get_modes
adv7511_get_edid_block
adv7511_irq_process
drm_helper_hpd_irq_event (acquires mode_config mutex again)
In adv7511_irq_process, don't call drm_helper_hpd_irq_event when not
called from the interrupt handler. It doesn't serve any purpose there
anyway.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
The driver has been converted to use drm_bridge instead of
drm_i2c_slave_encoder. We can now move it to the bridge folder.
Create a separate folder since we already have a couple of files and
expect more when we support audio and ADV7533.
Rename the driver to adv7511_drv.c. This will come in handy later
when the driver module will need to be built from multiple object
files.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
