There was a integer wraparound when mode_clock became too high,
and we didn't correct for the FEC overhead factor when dividing,
with the calculations breaking at HBR3.
As a result our calculated bpp was way too high, and the link width
limitation never came into effect.
Print out the resulting bpp calcululations as a sanity check, just
in case we ever have to debug it later on again.
We also used the wrong factor for FEC. While bspec mentions 2.4%,
all the calculations use 1/0.972261, and the same ratio should be
applied to data M/N as well, so use it there when FEC is enabled.
This fixes the FIFO underrun we are seeing with FEC enabled.
Changes since v2:
- Handle fec_enable in intel_link_compute_m_n, so only data M/N is adjusted. (Ville)
- Fix initial hardware readout for FEC. (Ville)
Changes since v3:
- Remove bogus fec_to_mode_clock. (Ville)
Changes since v4:
- Use the correct register for icl. (Ville)
- Split hw readout to a separate patch.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Fixes: d9218c8f6c ("drm/i915/dp: Add helpers for Compressed BPP and Slice Count for DSC")
Cc: <stable@vger.kernel.org> # v5.0+
Cc: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190925082110.17439-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
(cherry picked from commit ed06efb801)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Right now we are aware of two cases that needs another hotplug retry:
- Unpowered type-c dongles
- HDMI slow unplug
Both have a complete explanation in the code to schedule another run
of the hotplug handler.
It could have more checks to just trigger the retry in those two
specific cases but why would sink signal a long pulse if there is
no change? Also the drawback of running the hotplug handler again
is really low and that could fix another cases that we are not
aware.
Also retrying for old DP ports(non-DDI) to make it consistent and not
cause CI failures if those systems are connected to chamelium boards
that will be used to simulate the issues reported in here.
v2: Also retrying for old DP ports(non-DDI)(Imre)
v4: Renamed INTEL_HOTPLUG_NOCHANGE to INTEL_HOTPLUG_UNCHANGED to keep
it consistent(Rodrigo)
Tested-by: Timo Aaltonen <tjaalton@ubuntu.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190712005343.24571-2-jose.souza@intel.com
We must keep the TypeC port mode fixed for the duration of the connector
detection and each AUX transfers. Add a new TypeC lock holding it around
these two sequences. For consistency also hold the lock during the port
mode sanitization.
Whenever resetting the port mode (only during the detection for now) the
port's AUX power domain must be disabled already. Flush the async power
domain disabling work to ensure this.
A follow-up patch will make the port mode changing more robust by
postponing the change for active ports.
v2:
- Fix checkpatch issue: missing annotation for tc_lock.
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190628143635.22066-15-imre.deak@intel.com
