When the LLC and NUMA domains fully overlap, enabling both optimizations
in the built-in idle CPU selection policy is redundant, as it leads to
searching for an idle CPU within the same domain twice.
Likewise, if all online CPUs are within a single LLC domain, LLC
optimization is unnecessary.
Therefore, detect overlapping domains and enable topology optimizations
only when necessary.
Moreover, rely on the online CPUs for this detection logic, instead of
using the possible CPUs.
Fixes: 860a45219b ("sched_ext: Introduce NUMA awareness to the default idle selection policy")
Signed-off-by: Andrea Righi <arighi@nvidia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Instead of solving the underlying problem of the double invocation of
__sched_fork() for idle tasks, sched-ext decided to hack around the issue
by partially clearing out the entity struct to preserve the already
enqueued node. A provided analysis and solution has been ignored for four
months.
Now that someone else has taken care of cleaning it up, remove the
disgusting hack and clear out the full structure. Remove the comment in the
structure declaration as well, as there is no requirement for @node being
the last element anymore.
Fixes: f0e1a0643a ("sched_ext: Implement BPF extensible scheduler class")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/r/87ldy82wkc.ffs@tglx
Pull scheduler fixes from Thomas Gleixner:
- Plug a race between pick_next_task_fair() and try_to_wake_up() where
both try to write to the same task, even though both paths hold a
runqueue lock, but obviously from different runqueues.
The problem is that the store to task::on_rq in __block_task() is
visible to try_to_wake_up() which assumes that the task is not
queued. Both sides then operate on the same task.
Cure it by rearranging __block_task() so the the store to task::on_rq
is the last operation on the task.
- Prevent a potential NULL pointer dereference in task_numa_work()
task_numa_work() iterates the VMAs of a process. A concurrent unmap
of the address space can result in a NULL pointer return from
vma_next() which is unchecked.
Add the missing NULL pointer check to prevent this.
- Operate on the correct scheduler policy in task_should_scx()
task_should_scx() returns true when a task should be handled by sched
EXT. It checks the tasks scheduling policy.
This fails when the check is done before a policy has been set.
Cure it by handing the policy into task_should_scx() so it operates
on the requested value.
- Add the missing handling of sched EXT in the delayed dequeue
mechanism. This was simply forgotten.
* tag 'sched-urgent-2024-11-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/ext: Fix scx vs sched_delayed
sched: Pass correct scheduling policy to __setscheduler_class
sched/numa: Fix the potential null pointer dereference in task_numa_work()
sched: Fix pick_next_task_fair() vs try_to_wake_up() race
Pull sched_ext fixes from Tejun Heo:
- Instances of scx_ops_bypass() could race each other leading to
misbehavior. Fix by protecting the operation with a spinlock.
- selftest and userspace header fixes
* tag 'sched_ext-for-6.12-rc5-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext:
sched_ext: Fix enq_last_no_enq_fails selftest
sched_ext: Make cast_mask() inline
scx: Fix raciness in scx_ops_bypass()
scx: Fix exit selftest to use custom DSQ
sched_ext: Fix function pointer type mismatches in BPF selftests
selftests/sched_ext: add order-only dependency of runner.o on BPFOBJ
Similarly to commit dfa4ed29b1 ("sched_ext: Introduce LLC awareness to
the default idle selection policy"), extend the built-in idle CPU
selection policy to also prioritize CPUs within the same NUMA node.
With this change applied, the built-in CPU idle selection policy follows
this logic:
- always prioritize CPUs from fully idle SMT cores,
- select the same CPU if possible,
- select a CPU within the same LLC domain,
- select a CPU within the same NUMA node.
Both NUMA and LLC awareness features are enabled only when the system
has multiple NUMA nodes or multiple LLC domains.
In the future, we may want to improve the NUMA node selection to account
the node distance from prev_cpu. Currently, the logic only tries to keep
tasks running on the same NUMA node. If all CPUs within a node are busy,
the next NUMA node is chosen randomly.
Signed-off-by: Andrea Righi <arighi@nvidia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Commit 98442f0ccd ("sched: Fix delayed_dequeue vs
switched_from_fair()") overlooked that __setscheduler_prio(), now
__setscheduler_class() relies on p->policy for task_should_scx(), and
moved the call before __setscheduler_params() updates it, causing it
to be using the old p->policy value.
Resolve this by changing task_should_scx() to take the policy itself
instead of a task pointer, such that __sched_setscheduler() can pass
in the updated policy.
Fixes: 98442f0ccd ("sched: Fix delayed_dequeue vs switched_from_fair()")
Signed-off-by: Aboorva Devarajan <aboorvad@linux.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Tejun Heo <tj@kernel.org>
ops.dispatch() and ops.yield() may be fed a NULL task_struct pointer.
set_arg_maybe_null() is used to tell the verifier that they should be NULL
checked before being dereferenced. BPF now has an a lot prettier way to
express this - tagging arguments in CFI stubs with __nullable. Replace
set_arg_maybe_null() with __nullable CFI stub tags.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Vernet <void@manifault.com>
Acked-by: Martin KaFai Lau <martin.lau@kernel.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
CFI stubs can be used to tag arguments with __nullable (and possibly other
tags in the future) but for that to work the CFI stubs must have names that
are recognized by BPF. Rename them.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Vernet <void@manifault.com>
Acked-by: Martin KaFai Lau <martin.lau@kernel.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Rely on the scheduler topology information to implement basic LLC
awareness in the sched_ext build-in idle selection policy.
This allows schedulers using the built-in policy to make more informed
decisions when selecting an idle CPU in systems with multiple LLCs, such
as NUMA systems or chiplet-based architectures, and it helps keep tasks
within the same LLC domain, thereby improving cache locality.
For efficiency, LLC awareness is applied only to tasks that can run on
all the CPUs in the system for now. If a task's affinity is modified
from user space, it's the responsibility of user space to choose the
appropriate optimized scheduling domain.
Signed-off-by: Andrea Righi <arighi@nvidia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Update ops.select_cpu() documentation to clarify that this method is not
called for tasks that are restricted to run on a single CPU, as these
tasks do not have the option to select a different CPU.
Signed-off-by: Andrea Righi <arighi@nvidia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
In the sched_ext built-in idle CPU selection logic, when handling a
WF_SYNC wakeup, we always attempt to migrate the task to the waker's
CPU, as the waker is expected to yield the CPU after waking the task.
However, it may be preferable to keep the task on its previous CPU if
the waker's CPU is cache-affine.
The same approach is also used by the fair class and in other scx
schedulers, like scx_rusty and scx_bpfland.
Therefore, apply the same logic to the built-in idle CPU selection
policy as well.
Signed-off-by: Andrea Righi <andrea.righi@linux.dev>
Signed-off-by: Tejun Heo <tj@kernel.org>
Conflicts:
kernel/sched/ext.c
There's a context conflict between this upstream commit:
3fdb9ebcec sched_ext: Start schedulers with consistent p->scx.slice values
... and this fix in sched/urgent:
98442f0ccd sched: Fix delayed_dequeue vs switched_from_fair()
Resolve it.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
As described in commit b07996c7ab ("sched_ext: Don't hold
scx_tasks_lock for too long"), we're doing a cond_resched() every 32
calls to scx_task_iter_next() to avoid RCU and other stalls. That commit
also added a cpu_relax() to the codepath where we drop and reacquire the
lock, but as Waiman described in [0], cpu_relax() should only be
necessary in busy loops to avoid pounding on a cacheline (or to allow a
hypertwin to more fully utilize a core).
Let's remove the unnecessary cpu_relax().
[0]: https://lore.kernel.org/all/35b3889b-904a-4d26-981f-c8aa1557a7c7@redhat.com/
Cc: Waiman Long <llong@redhat.com>
Signed-off-by: David Vernet <void@manifault.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Commit 2e0199df25 ("sched/fair: Prepare exit/cleanup paths for delayed_dequeue")
and its follow up fixes try to deal with a rather unfortunate
situation where is task is enqueued in a new class, even though it
shouldn't have been. Mostly because the existing ->switched_to/from()
hooks are in the wrong place for this case.
This all led to Paul being able to trigger failures at something like
once per 10k CPU hours of RCU torture.
For now, do the ugly thing and move the code to the right place by
ignoring the switch hooks.
Note: Clean up the whole sched_class::switch*_{to,from}() thing.
Fixes: 2e0199df25 ("sched/fair: Prepare exit/cleanup paths for delayed_dequeue")
Reported-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20241003185037.GA5594@noisy.programming.kicks-ass.net
Iterating with scx_task_iter involves scx_tasks_lock and optionally the rq
lock of the task being iterated. Both locks can be released during iteration
and the iteration can be continued after re-grabbing scx_tasks_lock.
Currently, all lock handling is pushed to the caller which is a bit
cumbersome and makes it difficult to add lock-aware behaviors. Make the
scx_task_iter helpers handle scx_tasks_lock.
- scx_task_iter_init/scx_taks_iter_exit() now grabs and releases
scx_task_lock, respectively. Renamed to
scx_task_iter_start/scx_task_iter_stop() to more clearly indicate that
there are non-trivial side-effects.
- Add __ prefix to scx_task_iter_rq_unlock() to indicate that the function
is internal.
- Add scx_task_iter_unlock/relock(). The former drops both rq lock (if held)
and scx_tasks_lock and the latter re-locks only scx_tasks_lock.
This doesn't cause behavior changes and will be used to implement stall
avoidance.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Vernet <void@manifault.com>
Bypass mode was depending on ops.select_cpu() which can't be trusted as with
the rest of the BPF scheduler. Always enable and use scx_select_cpu_dfl() in
bypass mode.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Vernet <void@manifault.com>
Move the sanity check from the inner function scx_select_cpu_dfl() to the
exported kfunc scx_bpf_select_cpu_dfl(). This doesn't cause behavior
differences and will allow using scx_select_cpu_dfl() in bypass mode
regardless of scx_builtin_idle_enabled.
Signed-off-by: Tejun Heo <tj@kernel.org>
The disable path caps p->scx.slice to SCX_SLICE_DFL. As the field is already
being ignored at this stage during disable, the only effect this has is that
when the next BPF scheduler is loaded, it won't see unreasonable left-over
slices. Ultimately, this shouldn't matter but it's better to start in a
known state. Drop p->scx.slice capping from the disable path and instead
reset it to SCX_SLICE_DFL in the enable path.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Vernet <void@manifault.com>
This reverts commit 6f34d8d382.
Slice length is ignored while bypassing and tasks are switched on every tick
and thus the patch does not make any difference. The perceived difference
was from test noise.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Vernet <void@manifault.com>
pick_next_task_scx() was turned into pick_task_scx() since
commit 753e2836d1 ("sched_ext: Unify regular and core-sched pick
task paths"). Update the outdated message.
Signed-off-by: Honglei Wang <jameshongleiwang@126.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
scx_qmap and other schedulers in the SCX repo are using SCX_ENQ_WAKEUP to
tell whether ops.select_cpu() was called. This is incorrect as
ops.select_cpu() can be skipped in the wakeup path and leads to e.g.
incorrectly skipping direct dispatch for tasks that are bound to a single
CPU.
sched core has been updated to specify ENQUEUE_RQ_SELECTED if
->select_task_rq() was called. Map it to SCX_ENQ_CPU_SELECTED and update
scx_qmap to test it instead of SCX_ENQ_WAKEUP.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Vernet <void@manifault.com>
Cc: Daniel Hodges <hodges.daniel.scott@gmail.com>
Cc: Changwoo Min <multics69@gmail.com>
Cc: Andrea Righi <andrea.righi@linux.dev>
Cc: Dan Schatzberg <schatzberg.dan@gmail.com>
568894edbe ("sched_ext: Add scx_cgroup_enabled to gate cgroup operations
and fix scx_tg_online()") assumed that scx_cgroup_exit() is only called
after scx_cgroup_init() finished successfully. This isn't true.
scx_cgroup_exit() can be called without scx_cgroup_init() being called at
all or after scx_cgroup_init() failed in the middle.
As init state is tracked per cgroup, scx_cgroup_exit() can be used safely to
clean up in all cases. Remove the incorrect WARN_ON_ONCE().
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: 568894edbe ("sched_ext: Add scx_cgroup_enabled to gate cgroup operations and fix scx_tg_online()")
When the BPF scheduler fails, ops.exit() allows rich error reporting through
scx_exit_info. Use scx.exit() path consistently for all failures which can
be caused by the BPF scheduler:
- scx_ops_error() is called after ops.init() and ops.cgroup_init() failure
to record error information.
- ops.init_task() failure now uses scx_ops_error() instead of pr_err().
- The err_disable path updated to automatically trigger scx_ops_error() to
cover cases that the error message hasn't already been generated and
always return 0 indicating init success so that the error is reported
through ops.exit().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: David Vernet <void@manifault.com>
Cc: Daniel Hodges <hodges.daniel.scott@gmail.com>
Cc: Changwoo Min <multics69@gmail.com>
Cc: Andrea Righi <andrea.righi@linux.dev>
Cc: Dan Schatzberg <schatzberg.dan@gmail.com>
The #endif trailing comment of CONFIG_EXT_GROUP_SCHED is unmatched, so fix
it.
Signed-off-by: Zhang Qiao <zhangqiao22@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The enable path uses three big locks - scx_fork_rwsem, scx_cgroup_rwsem and
cpus_read_lock. Currently, the locks are grabbed together which is prone to
locking order problems.
For example, currently, there is a possible deadlock involving
scx_fork_rwsem and cpus_read_lock. cpus_read_lock has to nest inside
scx_fork_rwsem due to locking order existing in other subsystems. However,
there exists a dependency in the other direction during hotplug if hotplug
needs to fork a new task, which happens in some cases. This leads to the
following deadlock:
scx_ops_enable() hotplug
percpu_down_write(&cpu_hotplug_lock)
percpu_down_write(&scx_fork_rwsem)
block on cpu_hotplug_lock
kthread_create() waits for kthreadd
kthreadd blocks on scx_fork_rwsem
Note that this doesn't trigger lockdep because the hotplug side dependency
bounces through kthreadd.
With the preceding scx_cgroup_enabled change, this can be solved by
decoupling cpus_read_lock, which is needed for static_key manipulations,
from the other two locks.
- Move the first block of static_key manipulations outside of scx_fork_rwsem
and scx_cgroup_rwsem. This is now safe with the preceding
scx_cgroup_enabled change.
- Drop scx_cgroup_rwsem and scx_fork_rwsem between the two task iteration
blocks so that __scx_ops_enabled static_key enabling is outside the two
rwsems.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-tested-by: Aboorva Devarajan <aboorvad@linux.ibm.com>
Link: http://lkml.kernel.org/r/8cd0ec0c4c7c1bc0119e61fbef0bee9d5e24022d.camel@linux.ibm.com
The disable path uses three big locks - scx_fork_rwsem, scx_cgroup_rwsem and
cpus_read_lock. Currently, the locks are grabbed together which is prone to
locking order problems. With the preceding scx_cgroup_enabled change, we can
decouple them:
- As cgroup disabling no longer requires modifying a static_key which
requires cpus_read_lock(), no need to grab cpus_read_lock() before
grabbing scx_cgroup_rwsem.
- cgroup can now be independently disabled before tasks are moved back to
the fair class.
Relocate scx_cgroup_exit() invocation before scx_fork_rwsem is grabbed, drop
now unnecessary cpus_read_lock() and move static_key operations out of
scx_fork_rwsem. This decouples all three locks in the disable path.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-tested-by: Aboorva Devarajan <aboorvad@linux.ibm.com>
Link: http://lkml.kernel.org/r/8cd0ec0c4c7c1bc0119e61fbef0bee9d5e24022d.camel@linux.ibm.com
If the BPF scheduler does not implement ops.cgroup_init(), scx_tg_online()
didn't set SCX_TG_INITED which meant that ops.cgroup_exit(), even if
implemented, won't be called from scx_tg_offline(). This is because
SCX_HAS_OP(cgroupt_init) is used to test both whether SCX cgroup operations
are enabled and ops.cgroup_init() exists.
Fix it by introducing a separate bool scx_cgroup_enabled to gate cgroup
operations and use SCX_HAS_OP(cgroup_init) only to test whether
ops.cgroup_init() exists. Make all cgroup operations consistently use
scx_cgroup_enabled to test whether cgroup operations are enabled.
scx_cgroup_enabled is added instead of using scx_enabled() to ease planned
locking updates.
Signed-off-by: Tejun Heo <tj@kernel.org>
scx_ops_init_task() and the follow-up scx_ops_enable_task() in the fork path
were gated by scx_enabled() test and thus __scx_ops_enabled had to be turned
on before the first scx_ops_init_task() loop in scx_ops_enable(). However,
if an external entity causes sched_class switch before the loop is complete,
tasks which are not initialized could be switched to SCX.
The following can be reproduced by running a program which keeps toggling a
process between SCHED_OTHER and SCHED_EXT using sched_setscheduler(2).
sched_ext: Invalid task state transition 0 -> 3 for fish[1623]
WARNING: CPU: 1 PID: 1650 at kernel/sched/ext.c:3392 scx_ops_enable_task+0x1a1/0x200
...
Sched_ext: simple (enabling)
RIP: 0010:scx_ops_enable_task+0x1a1/0x200
...
switching_to_scx+0x13/0xa0
__sched_setscheduler+0x850/0xa50
do_sched_setscheduler+0x104/0x1c0
__x64_sys_sched_setscheduler+0x18/0x30
do_syscall_64+0x7b/0x140
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Fix it by gating scx_ops_init_task() separately using
scx_ops_init_task_enabled. __scx_ops_enabled is now set after all tasks are
finished with scx_ops_init_task().
Signed-off-by: Tejun Heo <tj@kernel.org>
scx_ops_enable() has two task iteration loops. The first one calls
scx_ops_init_task() on every task and the latter switches the eligible ones
into SCX. The first loop left the tasks in SCX_TASK_INIT state and then the
second loop switched it into READY before switching the task into SCX.
The distinction between INIT and READY is only meaningful in the fork path
where it's used to tell whether the task finished forking so that we can
tell ops.exit_task() accordingly. Leaving task in INIT state between the two
loops is incosistent with the fork path and incorrect. The following can be
triggered by running a program which keeps toggling a task between
SCHED_OTHER and SCHED_SCX while enabling a task:
sched_ext: Invalid task state transition 1 -> 3 for fish[1526]
WARNING: CPU: 2 PID: 1615 at kernel/sched/ext.c:3393 scx_ops_enable_task+0x1a1/0x200
...
Sched_ext: qmap (enabling+all)
RIP: 0010:scx_ops_enable_task+0x1a1/0x200
...
switching_to_scx+0x13/0xa0
__sched_setscheduler+0x850/0xa50
do_sched_setscheduler+0x104/0x1c0
__x64_sys_sched_setscheduler+0x18/0x30
do_syscall_64+0x7b/0x140
entry_SYSCALL_64_after_hwframe+0x76/0x7e
Fix it by transitioning to READY in the first loop right after
scx_ops_init_task() succeeds.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: David Vernet <void@manifault.com>
scx_ops_enable() used preempt_disable() around the task iteration loop to
switch tasks into SCX to guarantee forward progress of the task which is
running scx_ops_enable(). However, in the gap between setting
__scx_ops_enabled and preeempt_disable(), an external entity can put tasks
including the enabling one into SCX prematurely, which can lead to
malfunctions including stalls.
The bypass mode can wrap the entire enabling operation and guarantee forward
progress no matter what the BPF scheduler does. Use the bypass mode instead
to guarantee forward progress while enabling.
While at it, release and regrab scx_tasks_lock between the two task
iteration locks in scx_ops_enable() for clarity as there is no reason to
keep holding the lock between them.
Signed-off-by: Tejun Heo <tj@kernel.org>
The distinction between SCX_OPS_PREPPING and SCX_OPS_ENABLING is not used
anywhere and only adds confusion. Drop SCX_OPS_PREPPING.
Signed-off-by: Tejun Heo <tj@kernel.org>
check_hotplug_seq() is used to detect CPU hotplug event which occurred while
the BPF scheduler is being loaded so that initialization can be retried if
CPU hotplug events take place before the CPU hotplug callbacks are online.
As such, the best place to call it is in the same cpu_read_lock() section
that enables the CPU hotplug ops. Currently, it is called in the next
cpus_read_lock() block in scx_ops_enable(). The side effect of this
placement is a small window in which hotplug sequence detection can trigger
unnecessarily, which isn't critical.
Move check_hotplug_seq() invocation to the same cpus_read_lock() block as
the hotplug operation enablement to close the window and get the invocation
out of the way for planned locking updates.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: David Vernet <void@manifault.com>
While bypassing, tasks are scheduled in FIFO order which favors tasks that
hog CPUs. This can slow down e.g. unloading of the BPF scheduler. While
bypassing, guaranteeing timely forward progress is the main goal. There's no
point in giving long slices. Shorten the time slice used while bypassing
from 20ms to 5ms.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Vernet <void@manifault.com>
In the bypass mode, the global DSQ is used to schedule all tasks in simple
FIFO order. All tasks are queued into the global DSQ and all CPUs try to
execute tasks from it. This creates a lot of cross-node cacheline accesses
and scheduling across the node boundaries, and can lead to live-lock
conditions where the system takes tens of minutes to disable the BPF
scheduler while executing in the bypass mode.
Split the global DSQ per NUMA node. Each node has its own global DSQ. When a
task is dispatched to SCX_DSQ_GLOBAL, it's put into the global DSQ local to
the task's CPU and all CPUs in a node only consume its node-local global
DSQ.
This resolves a livelock condition which could be reliably triggered on an
2x EPYC 7642 system by running `stress-ng --race-sched 1024` together with
`stress-ng --workload 80 --workload-threads 10` while repeatedly enabling
and disabling a SCX scheduler.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Vernet <void@manifault.com>
To prepare for the addition of find_global_dsq(). No functional changes.
Signed-off-by: tejun heo <tj@kernel.org>
Acked-by: David Vernet <void@manifault.com>
SCX_DSQ_GLOBAL is special in that it can't be used as a priority queue and
is consumed implicitly, but all BPF DSQ related kfuncs could be used on it.
SCX_DSQ_GLOBAL will be split per-node for scalability and those operations
won't make sense anymore. Disallow SCX_DSQ_GLOBAL on scx_bpf_consume(),
scx_bpf_dsq_nr_queued() and bpf_iter_scx_dsq_new(). This means that
SCX_DSQ_GLOBAL can only be used as a dispatch target from BPF schedulers.
With scx_flatcg, which was using SCX_DSQ_GLOBAL as the fallback DSQ,
updated, this shouldn't affect any schedulers.
This leaves find_dsq_for_dispatch() the only user of find_non_local_dsq().
Open code and remove find_non_local_dsq().
Signed-off-by: tejun heo <tj@kernel.org>
Acked-by: David Vernet <void@manifault.com>
move_remote_task_to_local_dsq() is only defined on SMP configs but
scx_disaptch_from_dsq() was calling move_remote_task_to_local_dsq() on UP
configs too causing build failures. Add a dummy
move_remote_task_to_local_dsq() which triggers a warning.
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: 4c30f5ce4f ("sched_ext: Implement scx_bpf_dispatch[_vtime]_from_dsq()")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202409241108.jaocHiDJ-lkp@intel.com/
As discussed during the distro-centric session within the sched_ext
Microconference at LPC 2024, introduce a sequence counter that is
incremented every time a BPF scheduler is loaded.
This feature can help distributions in diagnosing potential performance
regressions by identifying systems where users are running (or have ran)
custom BPF schedulers.
Example:
arighi@virtme-ng~> cat /sys/kernel/sched_ext/enable_seq
0
arighi@virtme-ng~> sudo scx_simple
local=1 global=0
^CEXIT: unregistered from user space
arighi@virtme-ng~> cat /sys/kernel/sched_ext/enable_seq
1
In this way user-space tools (such as Ubuntu's apport and similar) are
able to gather and include this information in bug reports.
Cc: Giovanni Gherdovich <giovanni.gherdovich@suse.com>
Cc: Kleber Sacilotto de Souza <kleber.souza@canonical.com>
Cc: Marcelo Henrique Cerri <marcelo.cerri@canonical.com>
Cc: Phil Auld <pauld@redhat.com>
Signed-off-by: Andrea Righi <andrea.righi@linux.dev>
Signed-off-by: Tejun Heo <tj@kernel.org>
A task moving across CPUs should not trigger quiescent/runnable task state
events as the task is staying runnable the whole time and just stopping and
then starting on different CPUs. Suppress quiescent/runnable task state
events if task_on_rq_migrating().
Signed-off-by: Tejun Heo <tj@kernel.org>
Suggested-by: David Vernet <void@manifault.com>
Cc: Daniel Hodges <hodges.daniel.scott@gmail.com>
Cc: Changwoo Min <multics69@gmail.com>
Cc: Andrea Righi <andrea.righi@linux.dev>
Cc: Dan Schatzberg <schatzberg.dan@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
While the BPF scheduler is being unloaded, the following warning messages
trigger sometimes:
NOHZ tick-stop error: local softirq work is pending, handler #80!!!
This is caused by the CPU entering idle while there are pending softirqs.
The main culprit is the bypassing state assertion not being synchronized
with rq operations. As the BPF scheduler cannot be trusted in the disable
path, the first step is entering the bypass mode where the BPF scheduler is
ignored and scheduling becomes global FIFO.
This is implemented by turning scx_ops_bypassing() true. However, the
transition isn't synchronized against anything and it's possible for enqueue
and dispatch paths to have different ideas on whether bypass mode is on.
Make each rq track its own bypass state with SCX_RQ_BYPASSING which is
modified while rq is locked.
This removes most of the NOHZ tick-stop messages but not completely. I
believe the stragglers are from the sched core bug where pick_task_scx() can
be called without preceding balance_scx(). Once that bug is fixed, we should
verify that all occurrences of this error message are gone too.
v2: scx_enabled() test moved inside the for_each_possible_cpu() loop so that
the per-cpu states are always synchronized with the global state.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: David Vernet <void@manifault.com>
Once a task is put into a DSQ, the allowed operations are fairly limited.
Tasks in the built-in local and global DSQs are executed automatically and,
ignoring dequeue, there is only one way a task in a user DSQ can be
manipulated - scx_bpf_consume() moves the first task to the dispatching
local DSQ. This inflexibility sometimes gets in the way and is an area where
multiple feature requests have been made.
Implement scx_bpf_dispatch[_vtime]_from_dsq(), which can be called during
DSQ iteration and can move the task to any DSQ - local DSQs, global DSQ and
user DSQs. The kfuncs can be called from ops.dispatch() and any BPF context
which dosen't hold a rq lock including BPF timers and SYSCALL programs.
This is an expansion of an earlier patch which only allowed moving into the
dispatching local DSQ:
http://lkml.kernel.org/r/Zn4Cw4FDTmvXnhaf@slm.duckdns.org
v2: Remove @slice and @vtime from scx_bpf_dispatch_from_dsq[_vtime]() as
they push scx_bpf_dispatch_from_dsq_vtime() over the kfunc argument
count limit and often won't be needed anyway. Instead provide
scx_bpf_dispatch_from_dsq_set_{slice|vtime}() kfuncs which can be called
only when needed and override the specified parameter for the subsequent
dispatch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Daniel Hodges <hodges.daniel.scott@gmail.com>
Cc: David Vernet <void@manifault.com>
Cc: Changwoo Min <multics69@gmail.com>
Cc: Andrea Righi <andrea.righi@linux.dev>
Cc: Dan Schatzberg <schatzberg.dan@gmail.com>
