Pull perf fixes from Thomas Gleixner:
"Two fixes for the perf subsystem:
- Fix an inconsistency of RDPMC mm struct tagging across exec() which
causes RDPMC to fault.
- Correct the timestamp mechanics across IOC_DISABLE/ENABLE which
causes incorrect timestamps and total time calculations"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Fix time on IOC_ENABLE
perf/x86: Fix RDPMC vs. mm_struct tracking
Pull watchdog fix from Thomas Gleixner:
"A fix for the hardlockup watchdog to prevent false positives with
extreme Turbo-Modes which make the perf/NMI watchdog fire faster than
the hrtimer which is used to verify.
Slightly larger than the minimal fix, which just would increase the
hrtimer frequency, but comes with extra overhead of more watchdog
timer interrupts and thread wakeups for all users.
With this change we restrict the overhead to the extreme Turbo-Mode
systems"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kernel/watchdog: Prevent false positives with turbo modes
Wenwei Tao has noticed that our current assumption that the oom victim
is dying and never doing any visible changes after it dies, and so the
oom_reaper can tear it down, is not entirely true.
__task_will_free_mem consider a task dying when SIGNAL_GROUP_EXIT is set
but do_group_exit sends SIGKILL to all threads _after_ the flag is set.
So there is a race window when some threads won't have
fatal_signal_pending while the oom_reaper could start unmapping the
address space. Moreover some paths might not check for fatal signals
before each PF/g-u-p/copy_from_user.
We already have a protection for oom_reaper vs. PF races by checking
MMF_UNSTABLE. This has been, however, checked only for kernel threads
(use_mm users) which can outlive the oom victim. A simple fix would be
to extend the current check in handle_mm_fault for all tasks but that
wouldn't be sufficient because the current check assumes that a kernel
thread would bail out after EFAULT from get_user*/copy_from_user and
never re-read the same address which would succeed because the PF path
has established page tables already. This seems to be the case for the
only existing use_mm user currently (virtio driver) but it is rather
fragile in general.
This is even more fragile in general for more complex paths such as
generic_perform_write which can re-read the same address more times
(e.g. iov_iter_copy_from_user_atomic to fail and then
iov_iter_fault_in_readable on retry).
Therefore we have to implement MMF_UNSTABLE protection in a robust way
and never make a potentially corrupted content visible. That requires
to hook deeper into the PF path and check for the flag _every time_
before a pte for anonymous memory is established (that means all
!VM_SHARED mappings).
The corruption can be triggered artificially
(http://lkml.kernel.org/r/201708040646.v746kkhC024636@www262.sakura.ne.jp)
but there doesn't seem to be any real life bug report. The race window
should be quite tight to trigger most of the time.
Link: http://lkml.kernel.org/r/20170807113839.16695-3-mhocko@kernel.org
Fixes: aac4536355 ("mm, oom: introduce oom reaper")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Wenwei Tao <wenwei.tww@alibaba-inc.com>
Tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: "Kirill A. Shutemov" <kirill@shutemov.name>
Cc: Andrea Argangeli <andrea@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is existing use after free bug when deferred struct pages are
enabled:
The memblock_add() allocates memory for the memory array if more than
128 entries are needed. See comment in e820__memblock_setup():
* The bootstrap memblock region count maximum is 128 entries
* (INIT_MEMBLOCK_REGIONS), but EFI might pass us more E820 entries
* than that - so allow memblock resizing.
This memblock memory is freed here:
free_low_memory_core_early()
We access the freed memblock.memory later in boot when deferred pages
are initialized in this path:
deferred_init_memmap()
for_each_mem_pfn_range()
__next_mem_pfn_range()
type = &memblock.memory;
One possible explanation for why this use-after-free hasn't been hit
before is that the limit of INIT_MEMBLOCK_REGIONS has never been
exceeded at least on systems where deferred struct pages were enabled.
Tested by reducing INIT_MEMBLOCK_REGIONS down to 4 from the current 128,
and verifying in qemu that this code is getting excuted and that the
freed pages are sane.
Link: http://lkml.kernel.org/r/1502485554-318703-2-git-send-email-pasha.tatashin@oracle.com
Fixes: 7e18adb4f8 ("mm: meminit: initialise remaining struct pages in parallel with kswapd")
Signed-off-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Reviewed-by: Steven Sistare <steven.sistare@oracle.com>
Reviewed-by: Daniel Jordan <daniel.m.jordan@oracle.com>
Reviewed-by: Bob Picco <bob.picco@oracle.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These are the few pending fixes I have queued up for v4.13-final. One
is a a generic regression fix for recursive loops on kmod and the other
one is a trivial print out correction.
During the v4.13 development we assumed that recursive kmod loops were
no longer possible. Clearly that is not true. The regression fix makes
use of a new killable wait. We use a killable wait to be paranoid in
how signals might be sent to modprobe and only accept a proper SIGKILL.
The signal will only be available to userspace to issue *iff* a thread
has already entered a wait state, and that happens only if we've already
throttled after 50 kmod threads have been hit.
Note that although it may seem excessive to trigger a failure afer 5
seconds if all kmod thread remain busy, prior to the series of changes
that went into v4.13 we would actually *always* fatally fail any request
which came in if the limit was already reached. The new waiting
implemented in v4.13 actually gives us *more* breathing room -- the wait
for 5 seconds is a wait for *any* kmod thread to finish. We give up and
fail *iff* no kmod thread has finished and they're *all* running
straight for 5 consecutive seconds. If 50 kmod threads are running
consecutively for 5 seconds something else must be really bad.
Recursive loops with kmod are bad but they're also hard to implement
properly as a selftest without currently fooling current userspace tools
like kmod [1]. For instance kmod will complain when you run depmod if
it finds a recursive loop with symbol dependency between modules as such
this type of recursive loop cannot go upstream as the modules_install
target will fail after running depmod.
These tests already exist on userspace kmod upstream though (refer to
the testsuite/module-playground/mod-loop-*.c files). The same is not
true if request_module() is used though, or worst if aliases are used.
Likewise the issue with 64-bit kernels booting 32-bit userspace without
a binfmt handler built-in is also currently not detected and proactively
avoided by userspace kmod tools, or kconfig for all architectures.
Although we could complain in the kernel when some of these individual
recursive issues creep up, proactively avoiding these situations in
userspace at build time is what we should keep striving for.
Lastly, since recursive loops could happen with kmod it may mean
recursive loops may also be possible with other kernel usermode helpers,
this should be investigated and long term if we can come up with a more
sensible generic solution even better!
[0] https://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux.git/log/?h=20170809-kmod-for-v4.13-final
[1] https://git.kernel.org/pub/scm/utils/kernel/kmod/kmod.git
This patch (of 3):
This wait is similar to wait_event_interruptible_timeout() but only
accepts SIGKILL interrupt signal. Other signals are ignored.
Link: http://lkml.kernel.org/r/20170809234635.13443-2-mcgrof@kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Jessica Yu <jeyu@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Michal Marek <mmarek@suse.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Daniel Mentz <danielmentz@google.com>
Cc: David Binderman <dcb314@hotmail.com>
Cc: Matt Redfearn <matt.redfearn@imgetc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jaegeuk and Brad report a NULL pointer crash when writeback ending tries
to update the memcg stats:
BUG: unable to handle kernel NULL pointer dereference at 00000000000003b0
IP: test_clear_page_writeback+0x12e/0x2c0
[...]
RIP: 0010:test_clear_page_writeback+0x12e/0x2c0
Call Trace:
<IRQ>
end_page_writeback+0x47/0x70
f2fs_write_end_io+0x76/0x180 [f2fs]
bio_endio+0x9f/0x120
blk_update_request+0xa8/0x2f0
scsi_end_request+0x39/0x1d0
scsi_io_completion+0x211/0x690
scsi_finish_command+0xd9/0x120
scsi_softirq_done+0x127/0x150
__blk_mq_complete_request_remote+0x13/0x20
flush_smp_call_function_queue+0x56/0x110
generic_smp_call_function_single_interrupt+0x13/0x30
smp_call_function_single_interrupt+0x27/0x40
call_function_single_interrupt+0x89/0x90
RIP: 0010:native_safe_halt+0x6/0x10
(gdb) l *(test_clear_page_writeback+0x12e)
0xffffffff811bae3e is in test_clear_page_writeback (./include/linux/memcontrol.h:619).
614 mod_node_page_state(page_pgdat(page), idx, val);
615 if (mem_cgroup_disabled() || !page->mem_cgroup)
616 return;
617 mod_memcg_state(page->mem_cgroup, idx, val);
618 pn = page->mem_cgroup->nodeinfo[page_to_nid(page)];
619 this_cpu_add(pn->lruvec_stat->count[idx], val);
620 }
621
622 unsigned long mem_cgroup_soft_limit_reclaim(pg_data_t *pgdat, int order,
623 gfp_t gfp_mask,
The issue is that writeback doesn't hold a page reference and the page
might get freed after PG_writeback is cleared (and the mapping is
unlocked) in test_clear_page_writeback(). The stat functions looking up
the page's node or zone are safe, as those attributes are static across
allocation and free cycles. But page->mem_cgroup is not, and it will
get cleared if we race with truncation or migration.
It appears this race window has been around for a while, but less likely
to trigger when the memcg stats were updated first thing after
PG_writeback is cleared. Recent changes reshuffled this code to update
the global node stats before the memcg ones, though, stretching the race
window out to an extent where people can reproduce the problem.
Update test_clear_page_writeback() to look up and pin page->mem_cgroup
before clearing PG_writeback, then not use that pointer afterward. It
is a partial revert of 62cccb8c8e ("mm: simplify lock_page_memcg()")
but leaves the pageref-holding callsites that aren't affected alone.
Link: http://lkml.kernel.org/r/20170809183825.GA26387@cmpxchg.org
Fixes: 62cccb8c8e ("mm: simplify lock_page_memcg()")
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reported-by: Jaegeuk Kim <jaegeuk@kernel.org>
Tested-by: Jaegeuk Kim <jaegeuk@kernel.org>
Reported-by: Bradley Bolen <bradleybolen@gmail.com>
Tested-by: Brad Bolen <bradleybolen@gmail.com>
Cc: Vladimir Davydov <vdavydov@virtuozzo.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: <stable@vger.kernel.org> [4.6+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The hardlockup detector on x86 uses a performance counter based on unhalted
CPU cycles and a periodic hrtimer. The hrtimer period is about 2/5 of the
performance counter period, so the hrtimer should fire 2-3 times before the
performance counter NMI fires. The NMI code checks whether the hrtimer
fired since the last invocation. If not, it assumess a hard lockup.
The calculation of those periods is based on the nominal CPU
frequency. Turbo modes increase the CPU clock frequency and therefore
shorten the period of the perf/NMI watchdog. With extreme Turbo-modes (3x
nominal frequency) the perf/NMI period is shorter than the hrtimer period
which leads to false positives.
A simple fix would be to shorten the hrtimer period, but that comes with
the side effect of more frequent hrtimer and softlockup thread wakeups,
which is not desired.
Implement a low pass filter, which checks the perf/NMI period against
kernel time. If the perf/NMI fires before 4/5 of the watchdog period has
elapsed then the event is ignored and postponed to the next perf/NMI.
That solves the problem and avoids the overhead of shorter hrtimer periods
and more frequent softlockup thread wakeups.
Fixes: 58687acba5 ("lockup_detector: Combine nmi_watchdog and softlockup detector")
Reported-and-tested-by: Kan Liang <Kan.liang@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: dzickus@redhat.com
Cc: prarit@redhat.com
Cc: ak@linux.intel.com
Cc: babu.moger@oracle.com
Cc: peterz@infradead.org
Cc: eranian@google.com
Cc: acme@redhat.com
Cc: stable@vger.kernel.org
Cc: atomlin@redhat.com
Cc: akpm@linux-foundation.org
Cc: torvalds@linux-foundation.org
Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1708150931310.1886@nanos
Christian Brauner reported that if you use the TIOCGPTPEER ioctl() to
get a slave pty file descriptor, the resulting file descriptor doesn't
look right in /proc/<pid>/fd/<fd>. In particular, he wanted to use
readlink() on /proc/self/fd/<fd> to get the pathname of the slave pty
(basically implementing "ptsname{_r}()").
The reason for that was that we had generated the wrong 'struct path'
when we create the pty in ptmx_open().
In particular, the dentry was correct, but the vfsmount pointed to the
mount of the ptmx node. That _can_ be correct - in case you use
"/dev/pts/ptmx" to open the master - but usually is not. The normal
case is to use /dev/ptmx, which then looks up the pts/ directory, and
then the vfsmount of the ptmx node is obviously the /dev directory, not
the /dev/pts/ directory.
We actually did have the right vfsmount available, but in the wrong
place (it gets looked up in 'devpts_acquire()' when we get a reference
to the pts filesystem), and so ptmx_open() used the wrong mnt pointer.
The end result of this confusion was that the pty worked fine, but when
if you did TIOCGPTPEER to get the slave side of the pty, end end result
would also work, but have that dodgy 'struct path'.
And then when doing "d_path()" on to get the pathname, the vfsmount
would not match the root of the pts directory, and d_path() would return
an empty pathname thinking that the entry had escaped a bind mount into
another mount.
This fixes the problem by making devpts_acquire() return the vfsmount
for the pts filesystem, allowing ptmx_open() to trivially just use the
right mount for the pts dentry, and create the proper 'struct path'.
Reported-by: Christian Brauner <christian.brauner@ubuntu.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes from David Miller:
1) Fix TCP checksum offload handling in iwlwifi driver, from Emmanuel
Grumbach.
2) In ksz DSA tagging code, free SKB if skb_put_padto() fails. From
Vivien Didelot.
3) Fix two regressions with bonding on wireless, from Andreas Born.
4) Fix build when busypoll is disabled, from Daniel Borkmann.
5) Fix copy_linear_skb() wrt. SO_PEEK_OFF, from Eric Dumazet.
6) Set SKB cached route properly in inet_rtm_getroute(), from Florian
Westphal.
7) Fix PCI-E relaxed ordering handling in cxgb4 driver, from Ding
Tianhong.
8) Fix module refcnt leak in ULP code, from Sabrina Dubroca.
9) Fix use of GFP_KERNEL in atomic contexts in AF_KEY code, from Eric
Dumazet.
10) Need to purge socket write queue in dccp_destroy_sock(), also from
Eric Dumazet.
11) Make bpf_trace_printk() work properly on 32-bit architectures, from
Daniel Borkmann.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
bpf: fix bpf_trace_printk on 32 bit archs
PCI: fix oops when try to find Root Port for a PCI device
sfc: don't try and read ef10 data on non-ef10 NIC
net_sched: remove warning from qdisc_hash_add
net_sched/sfq: update hierarchical backlog when drop packet
net_sched: reset pointers to tcf blocks in classful qdiscs' destructors
ipv4: fix NULL dereference in free_fib_info_rcu()
net: Fix a typo in comment about sock flags.
ipv6: fix NULL dereference in ip6_route_dev_notify()
tcp: fix possible deadlock in TCP stack vs BPF filter
dccp: purge write queue in dccp_destroy_sock()
udp: fix linear skb reception with PEEK_OFF
ipv6: release rt6->rt6i_idev properly during ifdown
af_key: do not use GFP_KERNEL in atomic contexts
tcp: ulp: avoid module refcnt leak in tcp_set_ulp
net/cxgb4vf: Use new PCI_DEV_FLAGS_NO_RELAXED_ORDERING flag
net/cxgb4: Use new PCI_DEV_FLAGS_NO_RELAXED_ORDERING flag
PCI: Disable Relaxed Ordering Attributes for AMD A1100
PCI: Disable Relaxed Ordering for some Intel processors
PCI: Disable PCIe Relaxed Ordering if unsupported
...
Kalle Valo says:
====================
wireless-drivers fixes for 4.13
This time quite a few fixes for iwlwifi and one major regression fix
for brcmfmac. For the iwlwifi aggregation bug a small change was
needed for mac80211, but as Johannes is still away the mac80211 patch
is taken via wireless-drivers tree.
brcmfmac
* fix firmware crash (a recent regression in bcm4343{0,1,8}
iwlwifi
* Some simple PCI HW ID fix-ups and additions for family 9000
* Remove a bogus warning message with new FWs (bug #196915)
* Don't allow illegal channel options to be used (bug #195299)
* A fix for checksum offload in family 9000
* A fix serious throughput degradation in 11ac with multiple streams
* An old bug in SMPS where the firmware was not aware of SMPS changes
* Fix a memory leak in the SAR code
* Fix a stuck queue case in AP mode;
* Convert a WARN to a simple debug in a legitimate race case (from
which we can recover)
* Fix a severe throughput aggregation on 9000-family devices due to
aggregation issues, needed a small change in mac80211
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
copy_linear_skb() is broken; both of its callers actually
expect 'len' to be the amount we are trying to copy,
not the offset of the end.
Fix it keeping the meanings of arguments in sync with what the
callers (both of them) expect.
Also restore a saner behavior on EFAULT (i.e. preserving
the iov_iter position in case of failure):
The commit fd851ba9ca ("udp: harden copy_linear_skb()")
avoids the more destructive effect of the buggy
copy_linear_skb(), e.g. no more invalid memory access, but
said function still behaves incorrectly: when peeking with
offset it can fail with EINVAL instead of copying the
appropriate amount of memory.
Reported-by: Sasha Levin <alexander.levin@verizon.com>
Fixes: b65ac44674 ("udp: try to avoid 2 cache miss on dequeue")
Fixes: fd851ba9ca ("udp: harden copy_linear_skb()")
Signed-off-by: Al Viro <viro@ZenIV.linux.org.uk>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Tested-by: Sasha Levin <alexander.levin@verizon.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When bit4 is set in the PCIe Device Control register, it indicates
whether the device is permitted to use relaxed ordering.
On some platforms using relaxed ordering can have performance issues or
due to erratum can cause data-corruption. In such cases devices must avoid
using relaxed ordering.
The patch adds a new flag PCI_DEV_FLAGS_NO_RELAXED_ORDERING to indicate that
Relaxed Ordering (RO) attribute should not be used for Transaction Layer
Packets (TLP) targeted towards these affected root complexes.
This patch checks if there is any node in the hierarchy that indicates that
using relaxed ordering is not safe. In such cases the patch turns off the
relaxed ordering by clearing the capability for this device.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull tty/serial fixes from Greg KH:
"Here are two tty serial driver fixes for 4.13-rc5. One is a revert of
a -rc1 patch that turned out to not be a good idea, and the other is a
fix for the pl011 serial driver.
Both have been in linux-next with no reported issues"
* tag 'tty-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: Delete dead code for CIR serial ports"
tty: pl011: fix initialization order of QDF2400 E44
Pull staging/iio fixes from Greg KH:
"Here are some Staging and IIO driver fixes for 4.13-rc5.
Nothing major, just a number of small fixes for reported issues. All
of these have been in linux-next for a while now with no reported
issues. Full details are in the shortlog"
* tag 'staging-4.13-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: comedi: comedi_fops: do not call blocking ops when !TASK_RUNNING
iio: aspeed-adc: wait for initial sequence.
iio: accel: bmc150: Always restore device to normal mode after suspend-resume
staging:iio:resolver:ad2s1210 fix negative IIO_ANGL_VEL read
iio: adc: axp288: Fix the GPADC pin reading often wrongly returning 0
iio: adc: vf610_adc: Fix VALT selection value for REFSEL bits
iio: accel: st_accel: add SPI-3wire support
iio: adc: Revert "axp288: Drop bogus AXP288_ADC_TS_PIN_CTRL register modifications"
iio: adc: sun4i-gpadc-iio: fix unbalanced irq enable/disable
iio: pressure: st_pressure_core: disable multiread by default for LPS22HB
iio: light: tsl2563: use correct event code
MIN_NAPI_ID is used in various places outside of
CONFIG_NET_RX_BUSY_POLL wrapping, so when it's not set
we run into build errors such as:
net/core/dev.c: In function 'dev_get_by_napi_id':
net/core/dev.c:886:16: error: ‘MIN_NAPI_ID’ undeclared (first use in this function)
if (napi_id < MIN_NAPI_ID)
^~~~~~~~~~~
Thus, have MIN_NAPI_ID always defined to fix these errors.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch c4adfc822b ("bonding: make speed, duplex setting consistent
with link state") puts the link state to down if
bond_update_speed_duplex() cannot retrieve speed and duplex settings.
Assumably the patch was written with 802.3ad mode in mind which relies
on link speed/duplex settings. For other modes like active-backup these
settings are not required. Thus, only for these other modes, this patch
reintroduces support for slaves that do not support reporting speed or
duplex such as wireless devices. This fixes the regression reported in
bug 196547 (https://bugzilla.kernel.org/show_bug.cgi?id=196547).
Fixes: c4adfc822b ("bonding: make speed, duplex setting consistent
with link state")
Signed-off-by: Andreas Born <futur.andy@googlemail.com>
Acked-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull block fixes from Jens Axboe:
"A set of fixes that should go into this series. This contains:
- Fix from Bart for blk-mq requeue queue running, preventing a
continued loop of run/restart.
- Fix for a bio/blk-integrity issue, in two parts. One from
Christoph, fixing where verification happens, and one from Milan,
for a NULL profile.
- NVMe pull request, most of the changes being for nvme-fc, but also
a few trivial core/pci fixes"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvme: fix directive command numd calculation
nvme: fix nvme reset command timeout handling
nvme-pci: fix CMB sysfs file removal in reset path
lpfc: support nvmet_fc defer_rcv callback
nvmet_fc: add defer_req callback for deferment of cmd buffer return
nvme: strip trailing 0-bytes in wwid_show
block: Make blk_mq_delay_kick_requeue_list() rerun the queue at a quiet time
bio-integrity: only verify integrity on the lowest stacked driver
bio-integrity: Fix regression if profile verify_fn is NULL
Pull drm fixes from Dave Airlie:
"Nothing too earth shattering here, it just seems like lots of little
things all over the place.
msm has probably the larger amount of changes, but they all seem fine,
otherwise, some rockchip, i915, etnaviv and exynos fixes, along with
one nouveau regression fix for some older GPUs"
* tag 'drm-fixes-for-v4.13-rc5' of git://people.freedesktop.org/~airlied/linux: (35 commits)
drm/nouveau/disp/nv04: avoid creation of output paths
drm: make DRM_STM default n
drm/exynos: forbid creating framebuffers from too small GEM buffers
drm/etnaviv: Fix off-by-one error in reloc checking
drm/i915: fix backlight invert for non-zero minimum brightness
drm/i915/shrinker: Wrap need_resched() inside preempt-disable
drm/i915/perf: fix flex eu registers programming
drm/i915: Fix out-of-bounds array access in bdw_load_gamma_lut
drm/i915/gvt: Change the max length of mmio_reg_rw from 4 to 8
drm/i915/gvt: Initialize MMIO Block with HW state
drm/rockchip: vop: report error when check resource error
drm/rockchip: vop: round_up pitches to word align
drm/rockchip: vop: fix NV12 video display error
drm/rockchip: vop: fix iommu page fault when resume
drm/i915/gvt: clean workload queue if error happened
drm/i915/gvt: change resetting to resetting_eng
drm/msm: gpu: don't abuse dma_alloc for non-DMA allocations
drm/msm: gpu: call qcom_mdt interfaces only for ARCH_QCOM
drm/msm/adreno: Prevent unclocked access when retrieving timestamps
drm/msm: Remove __user from __u64 data types
...
Merge misc fixes from Andrew Morton:
"21 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (21 commits)
userfaultfd: replace ENOSPC with ESRCH in case mm has gone during copy/zeropage
zram: rework copy of compressor name in comp_algorithm_store()
rmap: do not call mmu_notifier_invalidate_page() under ptl
mm: fix list corruptions on shmem shrinklist
mm/balloon_compaction.c: don't zero ballooned pages
MAINTAINERS: copy virtio on balloon_compaction.c
mm: fix KSM data corruption
mm: fix MADV_[FREE|DONTNEED] TLB flush miss problem
mm: make tlb_flush_pending global
mm: refactor TLB gathering API
Revert "mm: numa: defer TLB flush for THP migration as long as possible"
mm: migrate: fix barriers around tlb_flush_pending
mm: migrate: prevent racy access to tlb_flush_pending
fault-inject: fix wrong should_fail() decision in task context
test_kmod: fix small memory leak on filesystem tests
test_kmod: fix the lock in register_test_dev_kmod()
test_kmod: fix bug which allows negative values on two config options
test_kmod: fix spelling mistake: "EMTPY" -> "EMPTY"
userfaultfd: hugetlbfs: remove superfluous page unlock in VM_SHARED case
mm: ratelimit PFNs busy info message
...
Nadav reported parallel MADV_DONTNEED on same range has a stale TLB
problem and Mel fixed it[1] and found same problem on MADV_FREE[2].
Quote from Mel Gorman:
"The race in question is CPU 0 running madv_free and updating some PTEs
while CPU 1 is also running madv_free and looking at the same PTEs.
CPU 1 may have writable TLB entries for a page but fail the pte_dirty
check (because CPU 0 has updated it already) and potentially fail to
flush.
Hence, when madv_free on CPU 1 returns, there are still potentially
writable TLB entries and the underlying PTE is still present so that a
subsequent write does not necessarily propagate the dirty bit to the
underlying PTE any more. Reclaim at some unknown time at the future
may then see that the PTE is still clean and discard the page even
though a write has happened in the meantime. I think this is possible
but I could have missed some protection in madv_free that prevents it
happening."
This patch aims for solving both problems all at once and is ready for
other problem with KSM, MADV_FREE and soft-dirty story[3].
TLB batch API(tlb_[gather|finish]_mmu] uses [inc|dec]_tlb_flush_pending
and mmu_tlb_flush_pending so that when tlb_finish_mmu is called, we can
catch there are parallel threads going on. In that case, forcefully,
flush TLB to prevent for user to access memory via stale TLB entry
although it fail to gather page table entry.
I confirmed this patch works with [4] test program Nadav gave so this
patch supersedes "mm: Always flush VMA ranges affected by zap_page_range
v2" in current mmotm.
NOTE:
This patch modifies arch-specific TLB gathering interface(x86, ia64,
s390, sh, um). It seems most of architecture are straightforward but
s390 need to be careful because tlb_flush_mmu works only if
mm->context.flush_mm is set to non-zero which happens only a pte entry
really is cleared by ptep_get_and_clear and friends. However, this
problem never changes the pte entries but need to flush to prevent
memory access from stale tlb.
[1] http://lkml.kernel.org/r/20170725101230.5v7gvnjmcnkzzql3@techsingularity.net
[2] http://lkml.kernel.org/r/20170725100722.2dxnmgypmwnrfawp@suse.de
[3] http://lkml.kernel.org/r/BD3A0EBE-ECF4-41D4-87FA-C755EA9AB6BD@gmail.com
[4] https://patchwork.kernel.org/patch/9861621/
[minchan@kernel.org: decrease tlb flush pending count in tlb_finish_mmu]
Link: http://lkml.kernel.org/r/20170808080821.GA31730@bbox
Link: http://lkml.kernel.org/r/20170802000818.4760-7-namit@vmware.com
Signed-off-by: Minchan Kim <minchan@kernel.org>
Signed-off-by: Nadav Amit <namit@vmware.com>
Reported-by: Nadav Amit <namit@vmware.com>
Reported-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch series "fixes of TLB batching races", v6.
It turns out that Linux TLB batching mechanism suffers from various
races. Races that are caused due to batching during reclamation were
recently handled by Mel and this patch-set deals with others. The more
fundamental issue is that concurrent updates of the page-tables allow
for TLB flushes to be batched on one core, while another core changes
the page-tables. This other core may assume a PTE change does not
require a flush based on the updated PTE value, while it is unaware that
TLB flushes are still pending.
This behavior affects KSM (which may result in memory corruption) and
MADV_FREE and MADV_DONTNEED (which may result in incorrect behavior). A
proof-of-concept can easily produce the wrong behavior of MADV_DONTNEED.
Memory corruption in KSM is harder to produce in practice, but was
observed by hacking the kernel and adding a delay before flushing and
replacing the KSM page.
Finally, there is also one memory barrier missing, which may affect
architectures with weak memory model.
This patch (of 7):
Setting and clearing mm->tlb_flush_pending can be performed by multiple
threads, since mmap_sem may only be acquired for read in
task_numa_work(). If this happens, tlb_flush_pending might be cleared
while one of the threads still changes PTEs and batches TLB flushes.
This can lead to the same race between migration and
change_protection_range() that led to the introduction of
tlb_flush_pending. The result of this race was data corruption, which
means that this patch also addresses a theoretically possible data
corruption.
An actual data corruption was not observed, yet the race was was
confirmed by adding assertion to check tlb_flush_pending is not set by
two threads, adding artificial latency in change_protection_range() and
using sysctl to reduce kernel.numa_balancing_scan_delay_ms.
Link: http://lkml.kernel.org/r/20170802000818.4760-2-namit@vmware.com
Fixes: 2084140594 ("mm: fix TLB flush race between migration, and
change_protection_range")
Signed-off-by: Nadav Amit <namit@vmware.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At queue creation, the transport allocates a local job struct
(struct nvmet_fc_fcp_iod) for each possible element of the queue.
When a new CMD is received from the wire, a jobs struct is allocated
from the queue and then used for the duration of the command.
The job struct contains buffer space for the wire command iu. Thus,
upon allocation of the job struct, the cmd iu buffer is copied to
the job struct and the LLDD may immediately free/reuse the CMD IU
buffer passed in the call.
However, in some circumstances, due to the packetized nature of FC
and the api of the FC LLDD which may issue a hw command to send the
wire response, but the LLDD may not get the hw completion for the
command and upcall the nvmet_fc layer before a new command may be
asynchronously received on the wire. In other words, its possible
for the initiator to get the response from the wire, thus believe a
command slot free, and send a new command iu. The new command iu
may be received by the LLDD and passed to the transport before the
LLDD had serviced the hw completion and made the teardown calls for
the original job struct. As such, there is no available job struct
available for the new io. E.g. it appears like the host sent more
queue elements than the queue size. It didn't based on it's
understanding.
Rather than treat this as a hard connection failure queue the new
request until the job struct does free up. As the buffer isn't
copied as there's no job struct, a special return value must be
returned to the LLDD to signify to hold off on recycling the cmd
iu buffer. And later, when a job struct is allocated and the
buffer copied, a new LLDD callback is introduced to notify the
LLDD and allow it to recycle it's command iu buffer.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Core Changes:
- dma-buf: Allow multiple sync_files to wrap a single dma-fence (Chris)
Driver Changes:
- rockchip: misc fixes to vop driver from the downstream rockchip tree (Mark)
- Error path cleanups to tc358767 & host1x (Lucas & Paul, respectively)
* tag 'drm-misc-fixes-2017-08-08' of git://anongit.freedesktop.org/git/drm-misc:
drm/rockchip: vop: report error when check resource error
drm/rockchip: vop: round_up pitches to word align
drm/rockchip: vop: fix NV12 video display error
drm/rockchip: vop: fix iommu page fault when resume
dma-buf/sync_file: Allow multiple sync_files to wrap a single dma-fence
drm/bridge: tc358767: fix probe without attached output node
Bunch of msm fixes for 4.13
* 'msm-fixes-4.13-rc3' of git://people.freedesktop.org/~robclark/linux:
drm/msm: gpu: don't abuse dma_alloc for non-DMA allocations
drm/msm: gpu: call qcom_mdt interfaces only for ARCH_QCOM
drm/msm/adreno: Prevent unclocked access when retrieving timestamps
drm/msm: Remove __user from __u64 data types
drm/msm: args->fence should be args->flags
drm/msm: Turn off hardware clock gating before reading A5XX registers
drm/msm: Allow hardware clock gating to be toggled
drm/msm: Remove some potentially blocked register ranges
drm/msm/mdp5: Drop clock names with "_clk" suffix
drm/msm/mdp5: Fix typo in encoder_enable path
drm/msm: NULL pointer dereference in drivers/gpu/drm/msm/msm_gem_vma.c
drm/msm: fix WARN_ON in add_vma() with no iommu
drm/msm/dsi: Calculate link clock rates with updated dsi->lanes
drm/msm/mdp5: fix unclocked register access in _cursor_set()
drm/msm: unlock on error in msm_gem_get_iova()
drm/msm: fix an integer overflow test
drm/msm/mdp5: Fix compilation warnings
Pull pin control fixes from Linus Walleij:
"These are the pin control fixes I have gathered since the return from
my vacation. They boiled in -next a while so let's get them in.
Apart from the documentation build it is purely driver fixes. Which is
nice. The Intel fixes seem kind of important.
- Fix the documentation build as the docs were moved
- Correct the UART pin list on the Intel Merrifield
- Fix pin assignment and number of pins on the Marvell Armada 37xx
pin controller
- Cover the Setzer models in the Chromebook DMI quirk in the Intel
cheryview driver so they start working
- Add the missing "sim" function to the sunxi driver
- Fix USB pin definitions on Uniphier Pro4
- Smatch fix for invalid reference in the zx pin control driver"
* tag 'pinctrl-v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: generic: update references to Documentation/pinctrl.txt
pinctrl: intel: merrifield: Correct UART pin lists
pinctrl: armada-37xx: Fix number of pin in south bridge
pinctrl: armada-37xx: Fix the pin 23 on south bridge
pinctrl: cherryview: Add Setzer models to the Chromebook DMI quirk
pinctrl: sunxi: add a missing function of A10/A20 pinctrl driver
pinctrl: uniphier: fix USB3 pin assignment for Pro4
pinctrl: zte: fix dereference of 'data' in zx_set_mux()
Pull i2c fixes from Wolfram Sang:
"The main thing is to allow empty id_tables for ACPI to make some
drivers get probed again. It looks a bit bigger than usual because it
needs some internal renaming, too.
Other than that, there is a fix for broken DSTDs, a super simple
enablement for ARM MPS, and two documentation fixes which I'd like to
see in v4.13 already"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: rephrase explanation of I2C_CLASS_DEPRECATED
i2c: allow i2c-versatile for ARM MPS platforms
i2c: designware: Some broken DSTDs use 1MiHz instead of 1MHz
i2c: designware: Print clock freq on invalid clock freq error
i2c: core: Allow empty id_table in ACPI case as well
i2c: mux: pinctrl: mention correct module name in Kconfig help text
Pull networking fixes from David Miller:
"The pull requests are getting smaller, that's progress I suppose :-)
1) Fix infinite loop in CIPSO option parsing, from Yujuan Qi.
2) Fix remote checksum handling in VXLAN and GUE tunneling drivers,
from Koichiro Den.
3) Missing u64_stats_init() calls in several drivers, from Florian
Fainelli.
4) TCP can set the congestion window to an invalid ssthresh value
after congestion window reductions, from Yuchung Cheng.
5) Fix BPF jit branch generation on s390, from Daniel Borkmann.
6) Correct MIPS ebpf JIT merge, from David Daney.
7) Correct byte order test in BPF test_verifier.c, from Daniel
Borkmann.
8) Fix various crashes and leaks in ASIX driver, from Dean Jenkins.
9) Handle SCTP checksums properly in mlx4 driver, from Davide
Caratti.
10) We can potentially enter tcp_connect() with a cached route
already, due to fastopen, so we have to explicitly invalidate it.
11) skb_warn_bad_offload() can bark in legitimate situations, fix from
Willem de Bruijn"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
net: avoid skb_warn_bad_offload false positives on UFO
qmi_wwan: fix NULL deref on disconnect
ppp: fix xmit recursion detection on ppp channels
rds: Reintroduce statistics counting
tcp: fastopen: tcp_connect() must refresh the route
net: sched: set xt_tgchk_param par.net properly in ipt_init_target
net: dsa: mediatek: add adjust link support for user ports
net/mlx4_en: don't set CHECKSUM_COMPLETE on SCTP packets
qed: Fix a memory allocation failure test in 'qed_mcp_cmd_init()'
hysdn: fix to a race condition in put_log_buffer
s390/qeth: fix L3 next-hop in xmit qeth hdr
asix: Fix small memory leak in ax88772_unbind()
asix: Ensure asix_rx_fixup_info members are all reset
asix: Add rx->ax_skb = NULL after usbnet_skb_return()
bpf: fix selftest/bpf/test_pkt_md_access on s390x
netvsc: fix race on sub channel creation
bpf: fix byte order test in test_verifier
xgene: Always get clk source, but ignore if it's missing for SGMII ports
MIPS: Add missing file for eBPF JIT.
bpf, s390: fix build for libbpf and selftest suite
...
Some drivers handle rx buffer reordering internally (and by extension
handle also the rx ba session timer internally), but do not ofload the
addba/delba negotiation.
Add an api for these drivers to properly tear-down the ba session,
including sending a delba.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Pull rdma fixes from Doug Ledford:
"Third set of -rc fixes for 4.13 cycle
- small set of miscellanous fixes
- a reasonably sizable set of IPoIB fixes that deal with multiple
long standing issues"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
IB/hns: checking for IS_ERR() instead of NULL
RDMA/mlx5: Fix existence check for extended address vector
IB/uverbs: Fix device cleanup
RDMA/uverbs: Prevent leak of reserved field
IB/core: Fix race condition in resolving IP to MAC
IB/ipoib: Notify on modify QP failure only when relevant
Revert "IB/core: Allow QP state transition from reset to error"
IB/ipoib: Remove double pointer assigning
IB/ipoib: Clean error paths in add port
IB/ipoib: Add get statistics support to SRIOV VF
IB/ipoib: Add multicast packets statistics
IB/ipoib: Set IPOIB_NEIGH_TBL_FLUSH after flushed completion initialization
IB/ipoib: Prevent setting negative values to max_nonsrq_conn_qp
IB/ipoib: Make sure no in-flight joins while leaving that mcast
IB/ipoib: Use cancel_delayed_work_sync when needed
IB/ipoib: Fix race between light events and interface restart
Pull SCSI fixes from James Bottomley:
"Two small fixes, one re-fix of a previous fix and five patches sorting
out hotplug in the bnx2X class of drivers. The latter is rather
involved, but necessary because these drivers have started dropping
lockdep recursion warnings on the hotplug lock because of its
conversion to a percpu rwsem"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sg: only check for dxfer_len greater than 256M
scsi: aacraid: reading out of bounds
scsi: qedf: Limit number of CQs
scsi: bnx2i: Simplify cpu hotplug code
scsi: bnx2fc: Simplify CPU hotplug code
scsi: bnx2i: Prevent recursive cpuhotplug locking
scsi: bnx2fc: Prevent recursive cpuhotplug locking
scsi: bnx2fc: Plug CPU hotplug race
Pull MTD fixes from Brian Norris:
"I missed getting these out for rc4, but here are some MTD fixes.
Just NAND fixes (in both the core handling, and a few drivers). Notes
stolen from Boris:
Core fixes:
- fix data interface setup for ONFI NANDs that do not support the SET
FEATURES command
- fix a kernel doc header
- fix potential integer overflow when retrieving timing information
from the parameter page
- fix wrong OOB layout for small page NANDs
Driver fixes:
- fix potential division-by-zero bug
- fix backward compat with old atmel-nand DT bindings
- fix ->setup_data_interface() in the atmel NAND driver"
* tag 'for-linus-20170807' of git://git.infradead.org/linux-mtd:
mtd: nand: atmel: Fix EDO mode check
mtd: nand: Declare tBERS, tR and tPROG as u64 to avoid integer overflow
mtd: nand: Fix timing setup for NANDs that do not support SET FEATURES
mtd: nand: Fix a docs build warning
mtd: nand: sunxi: fix potential divide-by-zero error
nand: fix wrong default oob layout for small pages using soft ecc
mtd: nand: atmel: Fix DT backward compatibility in pmecc.c
Update deprecated references to Documentation/pinctrl.txt since it has been
moved to Documentation/driver-api/pinctl.rst.
Signed-off-by: Ludovic Desroches <ludovic.desroches@o2linux.fr>
Fixes: 5a9b73832e ("pinctrl.txt: move it to the driver-api book")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes a bug associated with iscsit_reset_np_thread()
that can occur during parallel configfs rmdir of a single iscsi_np
used across multiple iscsi-target instances, that would result in
hung task(s) similar to below where configfs rmdir process context
was blocked indefinately waiting for iscsi_np->np_restart_comp
to finish:
[ 6726.112076] INFO: task dcp_proxy_node_:15550 blocked for more than 120 seconds.
[ 6726.119440] Tainted: G W O 4.1.26-3321 #2
[ 6726.125045] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 6726.132927] dcp_proxy_node_ D ffff8803f202bc88 0 15550 1 0x00000000
[ 6726.140058] ffff8803f202bc88 ffff88085c64d960 ffff88083b3b1ad0 ffff88087fffeb08
[ 6726.147593] ffff8803f202c000 7fffffffffffffff ffff88083f459c28 ffff88083b3b1ad0
[ 6726.155132] ffff88035373c100 ffff8803f202bca8 ffffffff8168ced2 ffff8803f202bcb8
[ 6726.162667] Call Trace:
[ 6726.165150] [<ffffffff8168ced2>] schedule+0x32/0x80
[ 6726.170156] [<ffffffff8168f5b4>] schedule_timeout+0x214/0x290
[ 6726.176030] [<ffffffff810caef2>] ? __send_signal+0x52/0x4a0
[ 6726.181728] [<ffffffff8168d7d6>] wait_for_completion+0x96/0x100
[ 6726.187774] [<ffffffff810e7c80>] ? wake_up_state+0x10/0x10
[ 6726.193395] [<ffffffffa035d6e2>] iscsit_reset_np_thread+0x62/0xe0 [iscsi_target_mod]
[ 6726.201278] [<ffffffffa0355d86>] iscsit_tpg_disable_portal_group+0x96/0x190 [iscsi_target_mod]
[ 6726.210033] [<ffffffffa0363f7f>] lio_target_tpg_store_enable+0x4f/0xc0 [iscsi_target_mod]
[ 6726.218351] [<ffffffff81260c5a>] configfs_write_file+0xaa/0x110
[ 6726.224392] [<ffffffff811ea364>] vfs_write+0xa4/0x1b0
[ 6726.229576] [<ffffffff811eb111>] SyS_write+0x41/0xb0
[ 6726.234659] [<ffffffff8169042e>] system_call_fastpath+0x12/0x71
It would happen because each iscsit_reset_np_thread() sets state
to ISCSI_NP_THREAD_RESET, sends SIGINT, and then blocks waiting
for completion on iscsi_np->np_restart_comp.
However, if iscsi_np was active processing a login request and
more than a single iscsit_reset_np_thread() caller to the same
iscsi_np was blocked on iscsi_np->np_restart_comp, iscsi_np
kthread process context in __iscsi_target_login_thread() would
flush pending signals and only perform a single completion of
np->np_restart_comp before going back to sleep within transport
specific iscsit_transport->iscsi_accept_np code.
To address this bug, add a iscsi_np->np_reset_count and update
__iscsi_target_login_thread() to keep completing np->np_restart_comp
until ->np_reset_count has reached zero.
Reported-by: Gary Guo <ghg@datera.io>
Tested-by: Gary Guo <ghg@datera.io>
Cc: Mike Christie <mchristi@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull ext4 fixes from Ted Ts'o:
"A large number of ext4 bug fixes and cleanups for v4.13"
* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
ext4: fix copy paste error in ext4_swap_extents()
ext4: fix overflow caused by missing cast in ext4_resize_fs()
ext4, project: expand inode extra size if possible
ext4: cleanup ext4_expand_extra_isize_ea()
ext4: restructure ext4_expand_extra_isize
ext4: fix forgetten xattr lock protection in ext4_expand_extra_isize
ext4: make xattr inode reads faster
ext4: inplace xattr block update fails to deduplicate blocks
ext4: remove unused mode parameter
ext4: fix warning about stack corruption
ext4: fix dir_nlink behaviour
ext4: silence array overflow warning
ext4: fix SEEK_HOLE/SEEK_DATA for blocksize < pagesize
ext4: release discard bio after sending discard commands
ext4: convert swap_inode_data() over to use swap() on most of the fields
ext4: error should be cleared if ea_inode isn't added to the cache
ext4: Don't clear SGID when inheriting ACLs
ext4: preserve i_mode if __ext4_set_acl() fails
ext4: remove unused metadata accounting variables
ext4: correct comment references to ext4_ext_direct_IO()
Pull media fixes from Mauro Carvalho Chehab:
"This series is larger than I would like to submit for -rc4. My
original intent were to sent it to either -rc2 or -rc3. Unfortunately,
due to my vacations, I got a lot of pending stuff after my return, and
had to do some biz trips, with prevented me to send this earlier.
Several fixes:
- some fixes at atomisp staging driver
- several gcc 7 warning fixes
- cleanup media SVG files, in order to fix PDF build on some distros
- fix random Kconfig build of venus driver
- some fixes for the venus driver
- some changes from semaphone to mutex in ngene's driver
- some locking fixes at dib0700 driver
- several fixes on ngene's driver and frontends to make it properly
support some new boards added on Kernel 4.13
- some fixes to CEC drivers
- omap_vout: vrfb: convert to dmaengine
- docs-rst: document EBUSY for VIDIOC_S_FMT
Please notice that the big diffstat changes here are at the SVG files.
Visually, the images look the same, but the file size is now a lot
smaller than before, and they don't use some XML tags that would cause
them to be badly parsed by some ImageMagick versions, or to require a
lot of memory by TeTex, with would break PDF output on some
distributions"
* tag 'media/v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (68 commits)
media: atomisp2: array underflow in imx_enum_frame_size()
media: atomisp2: array underflow in ap1302_enum_frame_size()
media: atomisp2: Array underflow in atomisp_enum_input()
media: platform: davinci: drop VPFE_CMD_S_CCDC_RAW_PARAMS
media: platform: davinci: return -EINVAL for VPFE_CMD_S_CCDC_RAW_PARAMS ioctl
media: venus: don't abuse dma_alloc for non-DMA allocations
media: venus: hfi: fix error handling in hfi_sys_init_done()
media: venus: fix compile-test build on non-qcom ARM platform
media: venus: mark PM functions as __maybe_unused
media: cec-notifier: small improvements
media: pulse8-cec: persistent_config should be off by default
media: cec: cec_transmit_attempt_done: ignore CEC_TX_STATUS_MAX_RETRIES
media: staging: atomisp: array underflow in ioctl
media: lirc: LIRC_GET_REC_RESOLUTION should return microseconds
media: svg: avoid too long lines
media: svg files: simplify files
media: selection.svg: simplify the SVG file
media: vimc: set id_table for platform drivers
media: staging: atomisp: disable warnings with cc-disable-warning
media: davinci: variable 'common' set but not used
...
Pull KVM fixes from Radim Krčmář:
"ARM:
- Yet another race with VM destruction plugged
- A set of small vgic fixes
x86:
- Preserve pending INIT
- RCU fixes in paravirtual async pf, VM teardown, and VMXOFF
emulation
- nVMX interrupt injection and dirty tracking fixes
- initialize to make UBSAN happy"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: arm/arm64: vgic: Use READ_ONCE fo cmpxchg
KVM: nVMX: Fix interrupt window request with "Acknowledge interrupt on exit"
KVM: nVMX: mark vmcs12 pages dirty on L2 exit
kvm: nVMX: don't flush VMCS12 during VMXOFF or VCPU teardown
KVM: nVMX: do not pin the VMCS12
KVM: avoid using rcu_dereference_protected
KVM: X86: init irq->level in kvm_pv_kick_cpu_op
KVM: X86: Fix loss of pending INIT due to race
KVM: async_pf: make rcu irq exit if not triggered from idle task
KVM: nVMX: fixes to nested virt interrupt injection
KVM: nVMX: do not fill vm_exit_intr_error_code in prepare_vmcs12
KVM: arm/arm64: Handle hva aging while destroying the vm
KVM: arm/arm64: PMU: Fix overflow interrupt injection
KVM: arm/arm64: Fix bug in advertising KVM_CAP_MSI_DEVID capability
The extended address vector is the highest bit in be32 variable,
but it was compared with the lowest. This patch fixes the endianness
of that check and removes already declared define.
Fixes: 17d2f88f92 ("IB/mlx5: Add ODP atomics support")
Reviewed-by: Artemy Kovalyov <artemyko@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Pull ceph fixes from Ilya Dryomov:
"A bunch of fixes and follow-ups for -rc1 Luminous patches: issues with
->reencode_message() and last minute RADOS semantic changes in
v12.1.2"
* tag 'ceph-for-4.13-rc4' of git://github.com/ceph/ceph-client:
libceph: make RECOVERY_DELETES feature create a new interval
libceph: upmap semantic changes
crush: assume weight_set != null imples weight_set_size > 0
libceph: fallback for when there isn't a pool-specific choose_arg
libceph: don't call ->reencode_message() more than once per message
libceph: make encode_request_*() work with r_mempool requests
Pull sound fixes from Takashi Iwai:
"Now we hit the usual ASoC-fix-flood in the middle of release.
Most of the changes are trivial and device-specific, while one
significant change is the fix for unbalanced of_graph_*() refcounts.
This involved a change in the graph API itself that had been a bit
messy"
* tag 'sound-4.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix speaker output from VAIO VPCL14M1R
device property: Fix usecount for of_graph_get_port_parent()
ASoC: rt5665: fix wrong register for bclk ratio control
ASoC: Intel: Use MCLK instead of BLCK as the sysclock for RT5514 codec on kabylake platform
ASoC: Intel: Enabling ASRC for RT5663 codec on kabylake platform
ASoC: codecs: msm8916-analog: fix DIG_CLK_CTL_RXD3_CLK_EN define
ASoC: Intel: Skylake: Fix missing sentinels in sst_acpi_mach
ASoC: sh: hac: add missing "int ret"
ASoC: samsung: odroid: Fix EPLL frequency values
ASoC: sgtl5000: Use snd_soc_kcontrol_codec()
ASoC: rt5665: fix GPIO6 pin function define
ASoC: ux500: Restore platform DAI assignments
ASoC: fix pcm-creation regression
ASoC: do not close shared backend dailink
ASoC: pxa: SND_PXA2XX_SOC should depend on HAS_DMA
ASoC: Intel: Skylake: Fix default dma_buffer_size
ASoC: rt5663: Update the HW default values based on the shipping version
ASoC: imx-ssi: add check on platform_get_irq return value
Pure refactor. This helper will be required in the xmit timer fix
later in the patch series. (Because the TLP logic will want to make
this calculation.)
Fixes: 6ba8a3b19e ("tcp: Tail loss probe (TLP)")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
