[Why]
HDCP locality check has strict timing requirements, currently broken
due to reliance on msleep which does not guarantee accuracy.
The PR moves the write-poll-read sequence into DMUB using new generic
Fused IO interface, where the timing accuracy is greatly improved.
New flow is enabled using DCN resource capability bit (none for now),
or using a debug flag.
[How]
* Extended mod_hdcp_config with new function for requesting DMUB
to execute a sequence of fused I2C/AUX commands and synchronously
wait until an outbox reply arrives or a timeout expires.
* If the timeout expires, send an abort to DMUB.
* Update HDCP to use the DMUB for locality check if supported.
* Add DC_HDCP_LC_FORCE_FW_ENABLE and DC_HDCP_LC_ENABLE_SW_FALLBACK.
* Make the first enable new flow regardless of resource capabilities.
* Make the second enable fallback to old SW flow.
* Clean up makefile source file listings for easier updates.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Dominik Kaszewski <dominik.kaszewski@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When BIOS includes a lot of custom brightness data points, walking
the entire list can be time consuming. This is most noticed when
dragging a power slider. The "higher" values are "slower" to drag
around.
[How]
Move custom brightness calculation loop into a static function. Before
starting the loop check the "half way" data point to see how it compares
to the input. If greater than the half way data point use that as the
starting point instead.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Depending on when the HW latching event (vupdate) of double-buffered
registers happen relative to the PSR SDP (signals panel psr enter/exit)
deadline, and how bad the Panel clock has drifted since the last ALPM
off event, there can be up to 3 frames of delay between sending the PSR
exit cmd to DMUB fw, and when the panel starts displaying live frames.
This can manifest as micro-stuttering when userspace commit patterns
cause rapid toggling of the DRM vblank counter, since PSR enter/exit is
hooked up to DRM vblank disable/enable respectively.
In the ideal world, the panel should present the live frame immediately
on PSR exit cmd. But due to HW design and PSR limitations, immediate
exit can only happen by chance, when:
1. PSR exit cmd is ack'd by FW before HW latching (vupdate) event, and
2. Panel's SDP deadline -- determined by it's PSR Start Delay in DPCD
71h -- is after the vupdate event. The PSR exit SDP can then be sent
immediately after HW latches. Otherwise, we have to wait 1 frame. And
3. There is negligible drift between the panel's clock and source clock.
Otherwise, there can be up to 1 frame of drift.
Note that this delay is not expected with Panel Replay.
[How]
Since PSR power savings can be quite substantial, and there are a lot of
systems in the wild with PSR panels, It'll be nice to have a middle
ground that balances user experience with power savings.
A simple way to achieve this is by extending the vblank offdelay, such
that additional PSR exit delays will be less perceivable.
We can set:
20/100 * offdelay_ms = 3_frames_ms
=> offdelay_ms = 5 * 3_frames_ms
This ensures that `3_frames_ms` will only be experienced as a 20% delay
on top how long the panel has been static, and thus make the delay
less perceivable.
If this ends up being too high of a percentage, it can be dropped
further in a future change.
Fixes: 537ef0f888 ("drm/amd/display: use new vblank enable policy for DCN35+")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
The displays currently don't get turned off until after other IP blocks
have been suspended. However turning off the displays first gives a
very visible response that the system is on it's way down.
[How]
Turn off displays in a prepare_suspend() callback instead when possible.
This will help for suspend and hibernate sequences.
The shutdown sequence however will not call prepare() so check whether
the state has been already saved to decide what to do.
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
GPU reset will attempt to restore cached state, but brightness doesn't
get restored. It will come back at 100% brightness, but userspace thinks
it's the previous value.
[How]
When running resume sequence if GPU is in reset restore brightness
to previous value.
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To avoid flickering during boot default brightness level set by BIOS
should be maintained for as much of the boot as feasible.
commit 2fe87f54ab ("drm/amd/display: Set default brightness according
to ACPI") attempted to set the right levels for AC vs DC, but brightness
still got reset to maximum level in initialization code for
setup_backlight_device().
[How]
Remove the hardcoded initialization in setup_backlight_device() and
instead program brightness value to match BIOS (AC or DC). This avoids a
brightness flicker from kernel changing the value. Userspace may however
still change it during boot.
Fixes: 2fe87f54ab ("drm/amd/display: Set default brightness according to ACPI")
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Tom Chung <chiahsuan.chung@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Upgrading the kernel may cause some systems that were previously not using
a firmware specified brightness curve to use one.
In the event of problems with this curve (for example an interpolation
error) add a new dcdebugmask value that can be used to turn it off. Also
add an info message to show that custom brightness curves are currently in
use.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Link: https://lore.kernel.org/r/20250228185145.186319-6-mario.limonciello@amd.com
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
All cases except a failure to create a copy of the current context will
call dc_state_release() on the copied context.
Use a _free() macro to free the context and then adjust the error handling
flow to drop the unnecessary use of goto statements.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We must implement an ACPI re-timer programming interface and notify
ACPI driver whenever a PHY transition is about to take place.
Because some trace lengths on certain platforms are very long,
then a re-timer may need to be programmed whenever a PHY transition
takes place. The implementation of this re-timer programming interface
will notify ACPI driver that PHY transition is taking place and it
will trigger the re-timer as needed.
First we need to gather retimer information from ACPI interface.
Then, in the PRE case, the re-timer interface needs to be called before we call
transmitter ENABLE.
In the POST case, it has to be called after we call transmitter DISABLE.
[How]
Implemented ACPI retimer programming interface.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Signed-off-by: Rafal Ostrowski <rostrows@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
some board designs have eDP0 connected to DP1, need a way to enable
support_edp0_on_dp1 flag, otherwise edp related features cannot work
[how]
do a dmi check during dm initialization to identify systems that
require support_edp0_on_dp1. Optimize quirk table with callback
functions to set quirk entries, retrieve_dmi_info can set quirks
according to quirk entries
Cc: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Yilin Chen <Yilin.Chen@amd.com>
Signed-off-by: Zaeem Mohamed <zaeem.mohamed@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When switching to drm_edid, we slightly changed how to get edid by
removing the possibility of getting them from dc_link when in aux
transaction mode. As MST doesn't initialize the connector with
`drm_connector_init_with_ddc()`, restore the original behavior to avoid
functional changes.
v2:
- Fix build warning of unchecked dereference (kernel test bot)
CC: Alex Hung <alex.hung@amd.com>
CC: Mario Limonciello <mario.limonciello@amd.com>
CC: Roman Li <Roman.Li@amd.com>
CC: Aurabindo Pillai <Aurabindo.Pillai@amd.com>
Fixes: 48edb2a425 ("drm/amd/display: switch amdgpu_dm_connector to use struct drm_edid")
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Don't try to operate on a drm_wb_connector as an amdgpu_dm_connector.
While dereferencing aconnector->base will "work" it's wrong and
might lead to unknown bad things. Just... don't.
Reviewed-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
The source device outputs a full RGB signal, but TV may
be set to use limited RGB. The mismatch in color
range leads to a degradation in image quality.
Display driver should have the ability to switch
between the full and limited RGB to match TV's settings.
[HOW]
Add support of the linux DRM "Broadcast RGB" property, which
indicates the Quantization Range (Full vs Limited) used.
User space can set this property to be "Automatic", "Full"
or "Limited 16:235" to adjust the output color range.
Reviewed-by: Jerry Zuo <jerry.zuo@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Yan Li <yan.li@amd.com>
Signed-off-by: Wayne Lin <wayne.lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Expose the OEM i2c bus on boards that support it.
This bus is used for OEM specific features like RGB, etc.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Allow the creation of an OEM i2c bus and use the proper
DC helpers for that case.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
link_index can be fetched from the ddc_service; no need for a separate
parameter. res is not used.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
