The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for drivers/phy/phy-can-transceiver.c
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20230714174841.4061919-1-robh@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This adds a bunch of new pixel clock- and tmds rates to the pre-pll
table which are required to get more VESA and some DMT rates working.
It has been completely re-calculated to match the min- and max-vco of
(750 MHz - 3.2 GHz) requirements. If more than one configuration would
have been possible the lowest fbdiv and refdiv (and therefore lowest
vco rate) has been preferred.
It's important to note, that RK3228 version of the phy does not support
fractional dividers. To support the most possible rates for this version
also in both 8-bit and 10-bit variant, some rates are not exact. The
maximum deviation of the pixel clock is 0.26, which perfectly fits into
VESA DMT recommendation of 0.5%.
I tested all possible rates on several screens from different
manufacturers with both RK3228 and RK3328. Both pre- and post-PLL
locking are slighlty faster now.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20230615171005.2251032-7-jonas@kwiboo.se
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Regular 8-bit and Deep Color video formats mainly differ in TMDS rate and
not in pixel clock rate.
When the hdmiphy clock is configured with the same pixel clock rate using
clk_set_rate() the clock framework do not signal the hdmi phy driver
to set_rate when switching between 8-bit and Deep Color.
This result in pre/post pll not being re-configured when switching between
regular 8-bit and Deep Color video formats.
Fix this by calling set_rate in power_on to force pre pll re-configuration.
Signed-off-by: Huicong Xu <xhc@rock-chips.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20230615171005.2251032-6-jonas@kwiboo.se
Signed-off-by: Vinod Koul <vkoul@kernel.org>
inno_write is used to configure 0xaa reg, that also hold the
POST_PLL_POWER_DOWN bit.
When POST_PLL_REFCLK_SEL_TMDS is configured the power down bit is not
taken into consideration.
Fix this by keeping the power down bit until configuration is complete.
Also reorder the reg write order for consistency.
Fixes: 53706a1168 ("phy: add Rockchip Innosilicon hdmi phy")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20230615171005.2251032-5-jonas@kwiboo.se
Signed-off-by: Vinod Koul <vkoul@kernel.org>
inno_hdmi_phy_rk3328_clk_recalc_rate() is returning a rate not found
in the pre pll config table when the fractal divider is used.
This can prevent proper power_on because a tmdsclock for the new rate
is not found in the pre pll config table.
Fix this by saving and returning a rounded pixel rate that exist
in the pre pll config table.
Fixes: 53706a1168 ("phy: add Rockchip Innosilicon hdmi phy")
Signed-off-by: Zheng Yang <zhengyang@rock-chips.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20230615171005.2251032-3-jonas@kwiboo.se
Signed-off-by: Vinod Koul <vkoul@kernel.org>
On RK3588 some registers need to be tweaked to support waking up from
suspend when a USB device is plugged into a port from a suspended PHY.
Without this change USB devices only work when they are plugged at
boot time.
Apart from that it optimizes settings to avoid devices toggling
between fullspeed and highspeed mode.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230522170324.61349-5-sebastian.reichel@collabora.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
clang with W=1 reports
drivers/phy/rockchip/phy-rockchip-pcie.c:122:19: error:
unused function 'phy_rd_cfg' [-Werror,-Wunused-function]
static inline u32 phy_rd_cfg(struct rockchip_pcie_phy *rk_phy,
^
This function is not used, so remove it.
Signed-off-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/20230321122503.1783311-1-trix@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20230307115900.2293120-23-u.kleine-koenig@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20230307115900.2293120-22-u.kleine-koenig@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20230307115900.2293120-21-u.kleine-koenig@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20230307115900.2293120-20-u.kleine-koenig@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The existing logic in tcphy_get_mode() can cause the phy to be
incorrectly configured to USB UFP or DisplayPort mode when
extcon_get_state returns an error code.
extcon_get_state() can return 0, 1, or a negative error code.
It is possible to get into the failing state with an extcon driver
which does not support the extcon connector id specified as the
second argument to extcon_get_state().
tcphy_get_mode()
->extcon_get_state()
-->find_cable_index_by_id()
--->return -EINVAL;
Fixes: e96be45cb8 ("phy: Add USB Type-C PHY driver for rk3399")
Signed-off-by: Neill Kapron <nkapron@google.com>
Reviewed-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230126001013.3707873-1-nkapron@google.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The rockchip,pipe-grf property is only used on rk3588, but not on
rk3568. Therefore this property is not present on rk3568 devices,
leading to the following message:
rockchip-snps-pcie3-phy fe8c0000.phy: failed to find rockchip,pipe_grf regmap
Fix that by only looking for this property on rk3588.
Fixes: 2e9bffc4f7 ("phy: rockchip: Support PCIe v3")
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Link: https://lore.kernel.org/r/20220927051752.53089-1-aurelien@aurel32.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add support for the Rockchip RK3568 DSI-DPHY. Registers were taken from
the BSP kernel driver and wherever possible cross referenced with the
TRM.
Refactor the code to allow the different compatible strings to set
either a max 1GHz timing table (all existing hardware) or a max 2.5GHz
timing table (the new RK356x). This works (for me) on both an RK3326
(PX30) and a new RK3566 device.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Link: https://lore.kernel.org/r/20220919164616.12492-3-macroalpha82@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
RK3568 supports PCIe v3 using not Combphy like PCIe v2 on rk3566.
It use a dedicated PCIe-phy. Add support for this.
Initial support by Shawn Lin, modifications by Peter Geis and Frank
Wunderlich.
Add data-lanes property for splitting pcie-lanes across controllers.
The data-lanes is an array where x=0 means lane is disabled and x > 0
means controller x is assigned to phy lane.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Suggested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20220825193836.54262-4-linux@fw-web.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
When the OTG port is fixed to host mode, the driver does not request its
IRQs, nor does it enable those IRQs in hardware. Similarly, the driver
should ignore the OTG port IRQs when handling the shared interrupt.
Otherwise, it would update the extcon based on an ID pin which may be in
an undefined state, or try to queue a uninitialized work item.
Fixes: 6a98df08cc ("phy: rockchip-inno-usb2: Fix muxed interrupt support")
Reported-by: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Link: https://lore.kernel.org/r/20220708061434.38115-1-samuel@sholland.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
This commit fixes two issues with the muxed interrupt handler. First,
the OTG port has the "bvalid" interrupt enabled, not "linestate". Since
only the linestate interrupt was handled, and not the bvalid interrupt,
plugging in a cable to the OTG port caused an interrupt storm.
Second, the return values from the individual port IRQ handlers need to
be OR-ed together. Otherwise, the lack of an interrupt from the last
port would cause the handler to erroneously return IRQ_NONE.
Fixes: ed2b5a8e6b ("phy: phy-rockchip-inno-usb2: support muxed interrupts")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Tested-by: Michael Riesch <michael.riesch@wolfvision.net>
Link: https://lore.kernel.org/r/20220414032258.40984-2-samuel@sholland.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The D-PHY specification (v1.2) explicitly mentions that the T-CLK-PRE
parameter's unit is Unit Interval(UI) and the minimum value is 8. Also,
kernel doc of the 'clk_pre' member of struct phy_configure_opts_mipi_dphy
mentions that it should be in UI. However, the dphy core driver wrongly
sets 'clk_pre' to 8000, which seems to hint that it's in picoseconds.
So, let's fix the dphy core driver to correctly reflect the T-CLK-PRE
parameter's minimum value according to the D-PHY specification.
I'm assuming that all impacted custom drivers shall program values in
TxByteClkHS cycles into hardware for the T-CLK-PRE parameter. The D-PHY
specification mentions that the frequency of TxByteClkHS is exactly 1/8
the High-Speed(HS) bit rate(each HS bit consumes one UI). So, relevant
custom driver code is changed to program those values as
DIV_ROUND_UP(cfg->clk_pre, BITS_PER_BYTE), then.
Note that I've only tested the patch with RM67191 DSI panel on i.MX8mq EVK.
Help is needed to test with other i.MX8mq, Meson and Rockchip platforms,
as I don't have the hardwares.
Fixes: 2ed869990e ("phy: Add MIPI D-PHY configuration options")
Tested-by: Liu Ying <victor.liu@nxp.com> # RM67191 DSI panel on i.MX8mq EVK
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com> # for phy-meson-axg-mipi-dphy.c
Tested-by: Neil Armstrong <narmstrong@baylibre.com> # for phy-meson-axg-mipi-dphy.c
Tested-by: Guido Günther <agx@sigxcpu.org> # Librem 5 (imx8mq) with it's rather picky panel
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Link: https://lore.kernel.org/r/20220124024007.1465018-1-victor.liu@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
