[ Upstream commit 76aed5e00f ]
Registers DSI_VM_CMD and DSI_SHADOW_DEBUG start at different
addresses in both MT8186 and MT8188 compared to the older IPs.
Add two members in struct mtk_dsi_driver_data to specify the
offsets for these two registers on a per-SoC basis, then do
specify those in all of the currently present SoC driver data.
This fixes writes to the Video Mode Command Packet Control
register, fixing enablement of command packet transmission
(VM_CMD_EN) and allowance of this transmission during the
VFP period (TS_VFP_EN) on both MT8186 and MT8188.
Fixes: 03d7adc410 ("drm/mediatek: Add mt8186 dsi compatible to mtk_dsi.c")
Fixes: 814d5341f3 ("drm/mediatek: Add mt8188 dsi compatible to mtk_dsi.c")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20241219112733.47907-1-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Adding the per-frame lp function of mt8188, which can keep HFP in HS and
reduce the time required for each line to enter and exit low power.
Per Frame LP:
|<----------One Active Frame-------->|
--______________________________________----___________________
^HSA+HBP^^RGB^^HFP^^HSA+HBP^^RGB^^HFP^ ^HSA+HBP^^RGB^^HFP^
Per Line LP:
|<---------------One Active Frame----------->|
--______________--______________--______________----______________
^HSA+HBP^^RGB^ ^HSA+HBP^^RGB^ ^HSA+HBP^^RGB^ ^HSA+HBP^^RGB^
Signed-off-by: Shuijing Li <shuijing.li@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20240826060654.24038-1-shuijing.li@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
mtk_find_possible_crtcs() assumes that the main path will always have
the CRTC with id 0, the ext id 1 and the third id 2. This is only true
if the paths are all available. But paths are optional (see also
comment in mtk_drm_kms_init()), e.g. the main path might not be enabled
or available at all. Then the CRTC IDs will shift one up, e.g. ext will
be 0 and the third path will be 1.
To fix that, dynamically calculate the IDs by the presence of the paths.
While at it, make the return code a signed one and return -ENODEV if no
path is found and handle the error in the callers.
Fixes: 5aa8e76476 ("drm/mediatek: dpi/dsi: Change the getting possible_crtc way")
Suggested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Michael Walle <mwalle@kernel.org>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20240606092122.2026313-1-mwalle@kernel.org/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Instead of open coding, use the mipi_dsi_pixel_format_to_bpp() helper
function from drm_mipi_dsi.h in mtk_dsi_poweron() and for validation
in mtk_dsi_bridge_mode_valid().
Note that this function changes the behavior of this driver: previously,
in case of unknown formats, it would (wrongly) assume that it should
account for a 24-bits format - now it will return an error and refuse
to set clocks and/or enable the DSI.
This is done because setting the wrong data rate will only produce a
garbage output that the display will misinterpret both because this
driver doesn't actually provide any extra-spec format support and/or
because the data rate (hence, the HS clock) will be wrong.
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20240215085316.56835-10-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Instead of open coding bitshifting for various register fields,
use the bitfield macro FIELD_PREP(): this allows to enhance the
human readability, decrease likeliness of mistakes (and register
field overflowing) and also to simplify the code.
The latter is especially seen in mtk_dsi_rxtx_control(), where
it was possible to change a switch to a short for loop and to
also remove the need to check for maximum DSI lanes == 4 thanks
to the FIELD_PREP macro masking the value.
While at it, also add the missing DA_HS_SYNC bitmask, used in
mtk_dsi_phy_timconfig().
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20240215085316.56835-5-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The register bits definitions for RGB666 formats are wrong in multiple
ways: first, in the DSI_PS_SEL bits region, the Packed 18-bits RGB666
format is selected with bit 1, while the Loosely Packed one is bit 2,
and second - the definition name "LOOSELY_PS_18BIT_RGB666" is wrong
because the loosely packed format is 24 bits instead!
Either way, functions mtk_dsi_ps_control_vact() and mtk_dsi_ps_control()
do not even agree on the DSI_PS_SEL bit to set in DSI_PSCTRL: one sets
loosely packed (24) on RGB666, the other sets packed (18), and the other
way around for RGB666_PACKED.
Fixing this entire stack of issues is done in one go:
- Use the correct bit for the Loosely Packed RGB666 definition
- Rename LOOSELY_PS_18BIT_RGB666 to LOOSELY_PS_24BIT_RGB666
- Change ps_bpp_mode in mtk_dsi_ps_control_vact() to set:
- Loosely Packed, 24-bits for MIPI_DSI_FMT_RGB666
- Packed, 18-bits for MIPI_DSI_FMT_RGB666_PACKED
Fixes: 2e54c14e31 ("drm/mediatek: Add DSI sub driver")
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20240215085316.56835-3-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Due to the initial confusion about MIPI_DSI_MODE_EOT_PACKET, properly
renamed to MIPI_DSI_MODE_NO_EOT_PACKET, reflecting its actual meaning,
both the DSI_TXRX_CON register setting for bit (HSTX_)DIS_EOT and the
later calculation for horizontal sync-active (HSA), back (HBP) and
front (HFP) porches got incorrect due to the logic being inverted.
This means that a number of settings were wrong because....:
- DSI_TXRX_CON register setting: bit (HSTX_)DIS_EOT should be
set in order to disable the End of Transmission packet;
- Horizontal Sync and Back/Front porches: The delta used to
calculate all of HSA, HBP and HFP should account for the
additional EOT packet.
Before this change...
- Bit (HSTX_)DIS_EOT was being set when EOT packet was enabled;
- For HSA/HBP/HFP delta... all three were wrong, as words were
added when EOT disabled, instead of when EOT packet enabled!
Invert the logic around flag MIPI_DSI_MODE_NO_EOT_PACKET in the
MediaTek DSI driver to fix the aforementioned issues.
Fixes: 8b2b99fd79 ("drm/mediatek: dsi: Fine tune the line time caused by EOTp")
Fixes: c87d1c4b5b ("drm/mediatek: dsi: Use symbolized register definition")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Tested-by: Michael Walle <mwalle@kernel.org>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230523104234.7849-1-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert the mediatek drm drivers from always returning zero in
the remove callback to the void returning variant.
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jyri Sarha <jyri.sarha@iki.fi>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230801110239.831099-8-u.kleine-koenig@pengutronix.de/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Fix the follow sparse warnings by adding missing headers:
drivers/gpu/drm/mediatek/mtk_cec.c:251:24: sparse: warning: symbol 'mtk_cec_driver' was not declared. Should it be static?
drivers/gpu/drm/mediatek/mtk_disp_ccorr.c:221:24: sparse: warning: symbol 'mtk_disp_ccorr_driver' was not declared. Should it be static?
drivers/gpu/drm/mediatek/mtk_disp_rdma.c:390:24: sparse: warning: symbol 'mtk_disp_rdma_driver' was not declared. Should it be static?
drivers/gpu/drm/mediatek/mtk_disp_gamma.c:209:24: sparse: warning: symbol 'mtk_disp_gamma_driver' was not declared. Should it be static?
drivers/gpu/drm/mediatek/mtk_disp_ovl.c:565:24: sparse: warning: symbol 'mtk_disp_ovl_driver' was not declared. Should it be static?
drivers/gpu/drm/mediatek/mtk_disp_color.c:164:24: sparse: warning: symbol 'mtk_disp_color_driver' was not declared. Should it be static?
drivers/gpu/drm/mediatek/mtk_disp_aal.c:161:24: sparse: warning: symbol 'mtk_disp_aal_driver' was not declared. Should it be static?
drivers/gpu/drm/mediatek/mtk_dpi.c:1109:24: sparse: warning: symbol 'mtk_dpi_driver' was not declared. Should it be static?
drivers/gpu/drm/mediatek/mtk_hdmi_ddc.c:340:24: sparse: warning: symbol 'mtk_hdmi_ddc_driver' was not declared. Should it be static?
drivers/gpu/drm/mediatek/mtk_dsi.c:1223:24: sparse: warning: symbol 'mtk_dsi_driver' was not declared. Should it be static?
Signed-off-by: Miles Chen <miles.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20230110091647.13265-1-miles.chen@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
According to Figure 16 Turnaround Procedure on page 36 in [1], you
can see the status of LP-00 -> LP10 -> LP11. This state can correspond
to the state of DSI from LP00 -> LP11 in mtk_dsi_lane_ready function
in mtk_dsi.c.
LP-00 -> LP10 -> LP11 takes about 2*TLPX time (refer to [1] page 51
to see that TLPX is 50ns)
The delay at the end of the mtk_dsi_lane_ready function should be
greater than the 2*TLPX specified by the DSI spec, and less than
the time specified by the DSI_RX (generally 6ms to 40ms), to avoid
problems caused by the RX specification
[1]:mipi_D-PHY_specification_v1-1
Fixes: 39e8d062b0 ("drm/mediatek: Keep dsi as LP00 before dcs cmds transfer")
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/1673330093-6771-2-git-send-email-xinlei.lee@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
As the comment right before the mtk_dsi_stop() call advises,
mtk_dsi_stop() should only be called after
mtk_drm_crtc_atomic_disable(). That's because that function calls
drm_crtc_wait_one_vblank(), which requires the vblank irq to be enabled.
Previously mtk_dsi_stop(), being in mtk_dsi_poweroff() and guarded by a
refcount, would only be called at the end of
mtk_drm_crtc_atomic_disable(), through the call to mtk_crtc_ddp_hw_fini().
Commit cde7e2e35c ("drm/mediatek: Separate poweron/poweroff from
enable/disable and define new funcs") moved the mtk_dsi_stop() call to
mtk_output_dsi_disable(), causing it to be called before
mtk_drm_crtc_atomic_disable(), and consequently generating vblank
timeout warnings during suspend.
Move the mtk_dsi_stop() call back to mtk_dsi_poweroff() so that we have
a working vblank irq during mtk_drm_crtc_atomic_disable() and stop
getting vblank timeout warnings.
Fixes: cde7e2e35c ("drm/mediatek: Separate poweron/poweroff from enable/disable and define new funcs")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Link: http://lists.infradead.org/pipermail/linux-mediatek/2022-August/046713.html
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
To comply with the panel sequence, hold the mipi signal to LP00 before
the dcs cmds transmission, and pull the mipi signal high from LP00 to
LP11 until the start of the dcs cmds transmission.
The normal panel timing is :
(1) pp1800 DC pull up
(2) avdd & avee AC pull high
(3) lcm_reset pull high -> pull low -> pull high
(4) Pull MIPI signal high (LP11) -> initial code -> send video data
(HS mode)
The power-off sequence is reversed.
If dsi is not in cmd mode, then dsi will pull the mipi signal high in
the mtk_output_dsi_enable function. The delay in lane_ready func is
the reaction time of dsi_rx after pulling up the mipi signal.
Fixes: 2dd8075d21 ("drm/mediatek: mtk_dsi: Use the drm_panel_bridge API")
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/1653012007-11854-4-git-send-email-xinlei.lee@mediatek.com/
Cc: <stable@vger.kernel.org> # 5.10.x: 7f6335c6a2: drm/mediatek: Modify dsi funcs to atomic operations
Cc: <stable@vger.kernel.org> # 5.10.x: cde7e2e35c: drm/mediatek: Separate poweron/poweroff from enable/disable and define new funcs
Cc: <stable@vger.kernel.org> # 5.10.x
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Some DSI RX devices (for example, anx7625) require last alignment of
packets on all lanes after each row of data is sent.
Otherwise, there will be some issues of shift or scroll for screen.
Take horizontal_sync_active_byte for a example,
we roundup the HSA packet data to lane number, and the subtraction of 2
is the packet data value added by the roundup operation, making the
long packets are integer multiples of lane number.
This value (2) varies with the lane number, and that is the reason we
do this operation when the lane number is 4.
In the previous operation of function "mtk_dsi_config_vdo_timing",
the length of HSA and HFP data packets has been adjusted to an
integration multiple of lane number.
Since the number of RGB data packets cannot be guaranteed to be an
integer multiple of lane number, we modify the data packet length of
HBP so that the number of HBP + RGB is equal to the lane number.
So after sending a line of data (HSA + HBP + RGB + HFP), the data
lanes are aligned.
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220309073637.3591-3-rex-bc.chen@mediatek.com
Mipi dsi panel drivers can use mipi_dsi_dcs_{set,get}_display_brightness()
to request backlight changes.
This can be done during panel initialization (dsi is in command mode)
or afterwards (dsi is in Video Mode).
When the DSI is in Video Mode, all commands are rejected.
Detect current DSI mode in mtk_dsi_host_transfer() and switch modes
temporarily to allow commands to be sent.
Signed-off-by: Julien STEPHAN <jstephan@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
DRM bridge drivers are now attaching their DSI device at probe time,
which requires us to register our DSI host in order to let the bridge
to probe: this recently started producing an endless -EPROBE_DEFER
loop on some machines that are using external bridges, like the
parade-ps8640, found on the ACER Chromebook R13.
Now that the DSI hosts/devices probe sequence is documented, we can
do adjustments to the mtk_dsi driver as to both fix now and make sure
to avoid this situation in the future: for this, following what is
documented in drm_bridge.c, move the mtk_dsi component_add() to the
mtk_dsi_ops.attach callback and delete it in the detach callback;
keeping in mind that we are registering a drm_bridge for our DSI,
which is only used/attached if the DSI Host is bound, it wouldn't
make sense to keep adding our bridge at probe time (as it would
be useless to have it if mtk_dsi_ops.attach() fails!), so also move
that one to the dsi host attach function (and remove it in detach).
Cc: <stable@vger.kernel.org> # 5.15.x
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
This patch adds the missing MODULE_DEVICE_TABLE definitions on different
Mediatek drivers which generates correct modalias for automatic loading
when these drivers are compiled as an external module.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Enabling EoTp will make the line time larger, so the hfp and
hbp should be reduced to keep line time.
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
For HSTX_CKLP_EN and DIS_EOT, use symbolized register
definition instead of magic number.
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
The interrupt trigger is already set by OF. When do devm_request_irq()
in driver, please use IRQF_TRIGGER_NONE and don't specify trigger type
again.
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Some ddp component exist in both display path and other path, so
sub driver should not directly call DRM driver's function. Moving
mtk_ddp_comp_init() from sub driver to DRM driver to achieve this.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Some ddp component exist in both display path and other path, so
sub driver should not directly call DRM driver's function. Let
DRM driver directly refer to sub driver's function so that sub
driver need not register these function to DRM driver.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Some ddp component exist in both display path and other path, so
sub driver interface should get rid of display info. Using device
instead of mtk_ddp_comp make interface general.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
