commit 662a9ece32 upstream.
When the USB5744 option is disabled, the onboard_usb driver warns about
unused functions:
drivers/usb/misc/onboard_usb_dev.c:358:12: error: 'onboard_dev_5744_i2c_write_byte' defined but not used [-Werror=unused-function]
358 | static int onboard_dev_5744_i2c_write_byte(struct i2c_client *client, u16 addr, u8 data)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/usb/misc/onboard_usb_dev.c:313:12: error: 'onboard_dev_5744_i2c_read_byte' defined but not used [-Werror=unused-function]
313 | static int onboard_dev_5744_i2c_read_byte(struct i2c_client *client, u16 addr, u8 *data)
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Extend the #ifdef block a little further to cover all of these functions.
Ideally we'd use use if(IS_ENABLED()) instead, but that doesn't currently
work because the i2c_transfer() and i2c_smbus_write_word_data() function
declarations are hidden when CONFIG_I2C is disabled.
Fixes: 1143d41922 ("usb: misc: onboard_usb_dev: Fix usb5744 initialization sequence")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20250523120947.2170302-1-arnd@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9f657a9280 upstream.
The Cypress HX3 USB3.0 hubs use different PID values depending
on the product variant. The comment in compatibles table is
misleading, as the currently used PIDs (0x6504 and 0x6506 for
USB 3.0 and USB 2.0, respectively) are defaults for the CYUSB331x,
while CYUSB330x and CYUSB332x variants use different values.
Based on the datasheet [1], update the compatible usb devices table
to handle different types of the hub.
The change also includes vendor mode PIDs, which are used by the
hub in I2C Master boot mode, if connected EEPROM contains invalid
signature or is blank. This allows to correctly boot the hub even
if the EEPROM will have broken content.
Number of vcc supplies and timing requirements are the same for all
HX variants, so the platform driver's match table does not have to
be extended.
[1] https://www.infineon.com/dgdl/Infineon-HX3_USB_3_0_Hub_Consumer_Industrial-DataSheet-v22_00-EN.pdf?fileId=8ac78c8c7d0d8da4017d0ecb53f644b8
Table 9. PID Values
Fixes: b43cd82a1a ("usb: misc: onboard-hub: add support for Cypress HX3 USB 3.0 family")
Cc: stable <stable@kernel.org>
Signed-off-by: Lukasz Czechowski <lukasz.czechowski@thaumatec.com>
Link: https://lore.kernel.org/r/20250425-onboard_usb_dev-v2-1-4a76a474a010@thaumatec.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ce15d6b3d5 upstream.
USB5744 SMBus initialization is done once in probe() and doing it in resume
is not supported so avoid going into suspend and reset the HUB.
There is a sysfs property 'always_powered_in_suspend' to implement this
feature but since default state should be set to a working configuration
so override this property value.
It fixes the suspend/resume testcase on Kria KR260 Robotics Starter Kit.
Fixes: 6782311d04 ("usb: misc: onboard_usb_dev: add Microchip usb5744 SMBus programming support")
Cc: stable@vger.kernel.org
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1733165302-1694891-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce new kernel config symbol for Microchip usb5744 SMBus programming
support. Since usb5744 i2c initialization routine uses i2c SMBus APIs these
APIs should only be invoked when kernel has I2C support. This new kernel
config describes the dependency on I2C kernel support and fix the below
build issues when USB_ONBOARD_DEV=y and CONFIG_I2C=m.
riscv64-linux-ld: drivers/usb/misc/onboard_usb_dev.o:
undefined reference to `i2c_find_device_by_fwnode'
drivers/usb/misc/onboard_usb_dev.c:408:(.text+0xb24): undefined
reference to `i2c_smbus_write_block_data'
<snip>
Parsing of the i2c-bus bus handle is not put under usb5744 kernel config
check as the intention is to report an error when DT is configured for
usb5744 SMBus support and kernel has USB_ONBOARD_DEV_USB5744 disabled.
Fixes: 6782311d04 ("usb: misc: onboard_usb_dev: add Microchip usb5744 SMBus programming support")
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Suggested-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202409140539.3Axwv38m-lkp@intel.com/
Acked-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Link: https://lore.kernel.org/r/1727529992-476088-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb5744 supports SMBus Configuration and it may be configured via the
SMBus slave interface during the hub start-up configuration stage.
To program it driver uses i2c-bus phandle (added in commit '02be19e914b8
dt-bindings: usb: Add support for Microchip usb5744 hub controller') to
get i2c client device and then based on usb5744 compatible check calls
usb5744 i2c default initialization sequence.
Apart from the USB command attach, prevent the hub from suspend.
when the USB Attach with SMBus (0xAA56) command is issued to the hub,
the hub is getting enumerated and then it puts in a suspend mode.
This causes the hub to NAK any SMBus access made by the SMBus Master
during this period and not able to see the hub's slave address while
running the "i2c probe" command.
Prevent the MCU from putting the HUB in suspend mode through register
write. The BYPASS_UDC_SUSPEND bit (Bit 3) of the RuntimeFlags2
register at address 0x411D controls this aspect of the hub. The
BYPASS_UDC_SUSPEND bit in register 0x411Dh must be set to ensure that the
MCU is always enabled and ready to respond to SMBus runtime commands.
This register needs to be written before the USB attach command is issued.
The byte sequence is as follows:
Slave addr: 0x2d 00 00 05 00 01 41 1D 08
Slave addr: 0x2d 99 37 00
Slave addr: 0x2d AA 56 00
Also since usb5744 i2c initialization routine uses i2c SMBus APIs invoke
these APIs only when i2c driver is enabled in the kernel configuration.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/1725732196-70975-3-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce dedicated field 'power_on_delay_us' in onboard platform data
and update its delay for USB5744 configuration. Hub itself requires some
delay after reset to get to state where configuration data is going to
be accepted. Without delay upcoming support for configuration via SMBUS
is reporting a failure on the first SMBus write.
i2c 2-002d: error -ENXIO: BYPASS_UDC_SUSPEND bit configuration failed
Similar delay is likely also required for default configuration but
because there is enough time (code execution) between reset and usage
of the hub any issue is not visible but it doesn't mean delay shouldn't
be reflected.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Suggested-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/1725732196-70975-2-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a match function for the onboard_usb_dev driver. Primary
matching is still done through the VID:PID pair, as usual for
USB devices. The new match function checks in addition whether
the device has a device tree node, which is a needed for using
the onboard_usb_dev driver.
Remove the check for a device tree node from _probe(), the new
match functions prevents devices without DT node from probing.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Jameson Thies <jthies@google.com>
Reviewed-by: Jameson Thies <jthies@google.com>
Link: https://lore.kernel.org/r/20240612180448.1.I805556c176c626872c15ce001f0e8198e1f95ae1@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The XMOS XVF3500 VocalFusion Voice Processor[1] is a low-latency, 32-bit
multicore controller for voice processing.
This device requires a specific power sequence, which consists of
enabling the regulators that control the 3V3 and 1V0 device supplies,
and a reset de-assertion after a delay of at least 100ns.
Once in normal operation, the XVF3500 registers itself as a USB device,
and it does not require any device-specific operations in the driver.
[1] https://www.xmos.com/xvf3500/
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Link: https://lore.kernel.org/r/20240325-onboard_xvf3500-v8-8-29e3f9222922@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most of the functionality this driver provides can be used by non-hub
devices as well.
To account for the hub-specific code, add a flag to the device data
structure and check its value for hub-specific code.
The 'always_powered_in_supend' attribute is only available for hub
devices, keeping the driver's default behavior for non-hub devices (keep
on in suspend).
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Link: https://lore.kernel.org/r/20240325-onboard_xvf3500-v8-6-29e3f9222922@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch prepares onboad_hub to support non-hub devices by renaming
the driver files and their content, the headers and their references.
The comments and descriptions have been slightly modified to keep
coherence and account for the specific cases that only affect onboard
hubs (e.g. peer-hub).
The "hub" variables in functions where "dev" (and similar names) variables
already exist have been renamed to onboard_dev for clarity, which adds a
few lines in cases where more than 80 characters are used.
No new functionality has been added.
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Link: https://lore.kernel.org/r/20240325-onboard_xvf3500-v8-2-29e3f9222922@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
