[ Upstream commit 04c03114be ]
soukjin bae reported a crash in tcp_v4_err() handling
ICMP_DEST_UNREACH after tcp_write_queue_head(sk)
returned a NULL pointer.
Current logic should have prevented this :
if (seq != tp->snd_una || !icsk->icsk_retransmits ||
!icsk->icsk_backoff || fastopen)
break;
Problem is the write queue might have been purged
and icsk_backoff has not been cleared.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: soukjin bae <soukjin.bae@samsung.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c09551c6ff ]
According to the algorithm described in the comment block at the
beginning of ip_rt_send_redirect, the host should try to send
'ip_rt_redirect_number' ICMP redirect packets with an exponential
backoff and then stop sending them at all assuming that the destination
ignores redirects.
If the device has previously sent some ICMP error packets that are
rate-limited (e.g TTL expired) and continues to receive traffic,
the redirect packets will never be transmitted. This happens since
peer->rate_tokens will be typically greater than 'ip_rt_redirect_number'
and so it will never be reset even if the redirect silence timeout
(ip_rt_redirect_silence) has elapsed without receiving any packet
requiring redirects.
Fix it by using a dedicated counter for the number of ICMP redirect
packets that has been sent by the host
I have not been able to identify a given commit that introduced the
issue since ip_rt_send_redirect implements the same rate-limiting
algorithm from commit 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5256083f6 ]
While implementing ipvlan l3 and l3s mode for kubernetes CNI plugin,
I ran into the issue that while l3 mode is working fine, l3s mode
does not have any connectivity to kube-apiserver and hence all pods
end up in Error state as well. The ipvlan master device sits on
top of a bond device and hostns traffic to kube-apiserver (also running
in hostns) is DNATed from 10.152.183.1:443 to 139.178.29.207:37573
where the latter is the address of the bond0. While in l3 mode, a
curl to https://10.152.183.1:443 or to https://139.178.29.207:37573
works fine from hostns, neither of them do in case of l3s. In the
latter only a curl to https://127.0.0.1:37573 appeared to work where
for local addresses of bond0 I saw kernel suddenly starting to emit
ARP requests to query HW address of bond0 which remained unanswered
and neighbor entries in INCOMPLETE state. These ARP requests only
happen while in l3s.
Debugging this further, I found the issue is that l3s mode is piggy-
backing on l3 master device, and in this case local routes are using
l3mdev_master_dev_rcu(dev) instead of net->loopback_dev as per commit
f5a0aab84b ("net: ipv4: dst for local input routes should use l3mdev
if relevant") and 5f02ce24c2 ("net: l3mdev: Allow the l3mdev to be
a loopback"). I found that reverting them back into using the
net->loopback_dev fixed ipvlan l3s connectivity and got everything
working for the CNI.
Now judging from 4fbae7d83c ("ipvlan: Introduce l3s mode") and the
l3mdev paper in [0] the only sole reason why ipvlan l3s is relying
on l3 master device is to get the l3mdev_ip_rcv() receive hook for
setting the dst entry of the input route without adding its own
ipvlan specific hacks into the receive path, however, any l3 domain
semantics beyond just that are breaking l3s operation. Note that
ipvlan also has the ability to dynamically switch its internal
operation from l3 to l3s for all ports via ipvlan_set_port_mode()
at runtime. In any case, l3 vs l3s soley distinguishes itself by
'de-confusing' netfilter through switching skb->dev to ipvlan slave
device late in NF_INET_LOCAL_IN before handing the skb to L4.
Minimal fix taken here is to add a IFF_L3MDEV_RX_HANDLER flag which,
if set from ipvlan setup, gets us only the wanted l3mdev_l3_rcv() hook
without any additional l3mdev semantics on top. This should also have
minimal impact since dev->priv_flags is already hot in cache. With
this set, l3s mode is working fine and I also get things like
masquerading pod traffic on the ipvlan master properly working.
[0] https://netdevconf.org/1.2/papers/ahern-what-is-l3mdev-paper.pdf
Fixes: f5a0aab84b ("net: ipv4: dst for local input routes should use l3mdev if relevant")
Fixes: 5f02ce24c2 ("net: l3mdev: Allow the l3mdev to be a loopback")
Fixes: 4fbae7d83c ("ipvlan: Introduce l3s mode")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Mahesh Bandewar <maheshb@google.com>
Cc: David Ahern <dsa@cumulusnetworks.com>
Cc: Florian Westphal <fw@strlen.de>
Cc: Martynas Pumputis <m@lambda.lt>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f97f4dd8b3 ]
IPv4 routing tables are flushed in two cases:
1. In response to events in the netdev and inetaddr notification chains
2. When a network namespace is being dismantled
In both cases only routes associated with a dead nexthop group are
flushed. However, a nexthop group will only be marked as dead in case it
is populated with actual nexthops using a nexthop device. This is not
the case when the route in question is an error route (e.g.,
'blackhole', 'unreachable').
Therefore, when a network namespace is being dismantled such routes are
not flushed and leaked [1].
To reproduce:
# ip netns add blue
# ip -n blue route add unreachable 192.0.2.0/24
# ip netns del blue
Fix this by not skipping error routes that are not marked with
RTNH_F_DEAD when flushing the routing tables.
To prevent the flushing of such routes in case #1, add a parameter to
fib_table_flush() that indicates if the table is flushed as part of
namespace dismantle or not.
Note that this problem does not exist in IPv6 since error routes are
associated with the loopback device.
[1]
unreferenced object 0xffff888066650338 (size 56):
comm "ip", pid 1206, jiffies 4294786063 (age 26.235s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 b0 1c 62 61 80 88 ff ff ..........ba....
e8 8b a1 64 80 88 ff ff 00 07 00 08 fe 00 00 00 ...d............
backtrace:
[<00000000856ed27d>] inet_rtm_newroute+0x129/0x220
[<00000000fcdfc00a>] rtnetlink_rcv_msg+0x397/0xa20
[<00000000cb85801a>] netlink_rcv_skb+0x132/0x380
[<00000000ebc991d2>] netlink_unicast+0x4c0/0x690
[<0000000014f62875>] netlink_sendmsg+0x929/0xe10
[<00000000bac9d967>] sock_sendmsg+0xc8/0x110
[<00000000223e6485>] ___sys_sendmsg+0x77a/0x8f0
[<000000002e94f880>] __sys_sendmsg+0xf7/0x250
[<00000000ccb1fa72>] do_syscall_64+0x14d/0x610
[<00000000ffbe3dae>] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[<000000003a8b605b>] 0xffffffffffffffff
unreferenced object 0xffff888061621c88 (size 48):
comm "ip", pid 1206, jiffies 4294786063 (age 26.235s)
hex dump (first 32 bytes):
6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b kkkkkkkkkkkkkkkk
6b 6b 6b 6b 6b 6b 6b 6b d8 8e 26 5f 80 88 ff ff kkkkkkkk..&_....
backtrace:
[<00000000733609e3>] fib_table_insert+0x978/0x1500
[<00000000856ed27d>] inet_rtm_newroute+0x129/0x220
[<00000000fcdfc00a>] rtnetlink_rcv_msg+0x397/0xa20
[<00000000cb85801a>] netlink_rcv_skb+0x132/0x380
[<00000000ebc991d2>] netlink_unicast+0x4c0/0x690
[<0000000014f62875>] netlink_sendmsg+0x929/0xe10
[<00000000bac9d967>] sock_sendmsg+0xc8/0x110
[<00000000223e6485>] ___sys_sendmsg+0x77a/0x8f0
[<000000002e94f880>] __sys_sendmsg+0xf7/0x250
[<00000000ccb1fa72>] do_syscall_64+0x14d/0x610
[<00000000ffbe3dae>] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[<000000003a8b605b>] 0xffffffffffffffff
Fixes: 8cced9eff1 ("[NETNS]: Enable routing configuration in non-initial namespace.")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21ba8847f8 upstream.
Currently, we use check_hlist() for garbage colleciton. However, we
use the ‘zone’ from the counted entry to query the existence of
existing entries in the hlist. This could be wrong when they are in
different zones, and this patch fixes this issue.
Fixes: e59ea3df3f ("netfilter: xt_connlimit: honor conntrack zone if available")
Signed-off-by: Yi-Hung Wei <yihung.wei@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
[mfo: backport: refresh context lines and use older symbol/file names, note hunk 5:
- nf_conncount.c -> xt_connlimit.c
- nf_conncount_rb -> xt_connlimit_rb
- nf_conncount_tuple -> xt_connlimit_conn
- hunk 5: remove check for non-NULL 'tuple', that isn't required as it's introduced
by upstream commit 35d8deb80 ("netfilter: conncount: Support count only use case")
which addresses nf_conncount_count() that does not exist yet -- it's introduced by
upstream commit 625c556118 ("netfilter: connlimit: split xt_connlimit into front
and backend"), a refactor change.
- nft_connlimit.c -> removed, not used/doesn't exist yet.]
Signed-off-by: Mauricio Faria de Oliveira <mfo@canonical.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 5e5cbc7b23 upstream.
This patch provides an interface to maintain the list of connections and
the lookup function to obtain the number of connections in the list.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
[mfo: backport: refresh context lines and use older symbol/file names:
- nf_conntrack_count.h: new file, add include guards.
- nf_conncount.c -> xt_connlimit.c.
- nf_conncount_rb -> xt_connlimit_rb
- nf_conncount_tuple -> xt_connlimit_conn
- conncount_rb_cachep -> connlimit_rb_cachep
- conncount_conn_cachep -> connlimit_conn_cachep]
Signed-off-by: Mauricio Faria de Oliveira <mfo@canonical.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3a0ed3e961 ]
Al Viro mentioned (Message-ID
<20170626041334.GZ10672@ZenIV.linux.org.uk>)
that there is probably a race condition
lurking in accesses of sk_stamp on 32-bit machines.
sock->sk_stamp is of type ktime_t which is always an s64.
On a 32 bit architecture, we might run into situations of
unsafe access as the access to the field becomes non atomic.
Use seqlocks for synchronization.
This allows us to avoid using spinlocks for readers as
readers do not need mutual exclusion.
Another approach to solve this is to require sk_lock for all
modifications of the timestamps. The current approach allows
for timestamps to have their own lock: sk_stamp_lock.
This allows for the patch to not compete with already
existing critical sections, and side effects are limited
to the paths in the patch.
The addition of the new field maintains the data locality
optimizations from
commit 9115e8cd2a ("net: reorganize struct sock for better data
locality")
Note that all the instances of the sk_stamp accesses
are either through the ioctl or the syscall recvmsg.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fb6df5a623 ]
In sctp_hash_transport/sctp_epaddr_lookup_transport, it dereferences
a transport's asoc under rcu_read_lock while asoc is freed not after
a grace period, which leads to a use-after-free panic.
This patch fixes it by calling kfree_rcu to make asoc be freed after
a grace period.
Note that only the asoc's memory is delayed to free in the patch, it
won't cause sk to linger longer.
Thanks Neil and Marcelo to make this clear.
Fixes: 7fda702f93 ("sctp: use new rhlist interface on sctp transport rhashtable")
Fixes: cd2b708750 ("sctp: check duplicate node before inserting a new transport")
Reported-by: syzbot+0b05d8aa7cb185107483@syzkaller.appspotmail.com
Reported-by: syzbot+aad231d51b1923158444@syzkaller.appspotmail.com
Suggested-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e6ac64d4c4 ]
While skb_push() makes the kernel panic if the skb headroom is less than
the unaligned hardware header size, it will proceed normally in case we
copy more than that because of alignment, and we'll silently corrupt
adjacent slabs.
In the case fixed by the previous patch,
"ipv6: Check available headroom in ip6_xmit() even without options", we
end up in neigh_hh_output() with 14 bytes headroom, 14 bytes hardware
header and write 16 bytes, starting 2 bytes before the allocated buffer.
Always check we're not writing before skb->head and, if the headroom is
not enough, warn and drop the packet.
v2:
- instead of panicking with BUG_ON(), WARN_ON_ONCE() and drop the packet
(Eric Dumazet)
- if we avoid the panic, though, we need to explicitly check the headroom
before the memcpy(), otherwise we'll have corrupted slabs on a running
kernel, after we warn
- use __skb_push() instead of skb_push(), as the headroom check is
already implemented here explicitly (Eric Dumazet)
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ff45d820a2 upstream.
Previously the TLS ulp context would leak if we attached a TLS ulp
to a socket but did not use the TLS_TX setsockopt,
or did use it but it failed.
This patch solves the issue by overriding prot[TLS_BASE_TX].close
and fixing tls_sk_proto_close to work properly
when its called with ctx->tx_conf == TLS_BASE_TX.
This patch also removes ctx->free_resources as we can use ctx->tx_conf
to obtain the relevant information.
Fixes: 3c4d755915 ('tls: kernel TLS support')
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[bwh: Backported to 4.14: Keep using tls_ctx_free() as introduced by
the earlier backport of "tls: zero the crypto information from
tls_context before freeing"]
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 6d88207fcf upstream.
The tx configuration is now stored in ctx->tx_conf.
And sk->sk_prot is updated trough a function
This will simplify things when we add rx
and support for different possible
tx and rx cross configurations.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8873c064d1 upstream.
syzkaller was able to hit the WARN_ON(sock_owned_by_user(sk));
in tcp_close()
While a socket is being closed, it is very possible other
threads find it in rtnetlink dump.
tcp_get_info() will acquire the socket lock for a short amount
of time (slow = lock_sock_fast(sk)/unlock_sock_fast(sk, slow);),
enough to trigger the warning.
Fixes: 67db3e4bfb ("tcp: no longer hold ehash lock while calling tcp_get_info()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2ab2ddd301 ]
Timer handlers do not imply rcu_read_lock(), so my recent fix
triggered a LOCKDEP warning when SYNACK is retransmit.
Lets add rcu_read_lock()/rcu_read_unlock() pairs around ireq->ireq_opt
usages instead of guessing what is done by callers, since it is
not worth the pain.
Get rid of ireq_opt_deref() helper since it hides the logic
without real benefit, since it is now a standard rcu_dereference().
Fixes: 1ad98e9d1b ("tcp/dccp: fix lockdep issue when SYN is backlogged")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1ad98e9d1b ]
In normal SYN processing, packets are handled without listener
lock and in RCU protected ingress path.
But syzkaller is known to be able to trick us and SYN
packets might be processed in process context, after being
queued into socket backlog.
In commit 06f877d613 ("tcp/dccp: fix other lockdep splats
accessing ireq_opt") I made a very stupid fix, that happened
to work mostly because of the regular path being RCU protected.
Really the thing protecting ireq->ireq_opt is RCU read lock,
and the pseudo request refcnt is not relevant.
This patch extends what I did in commit 449809a66c ("tcp/dccp:
block BH for SYN processing") by adding an extra rcu_read_{lock|unlock}
pair in the paths that might be taken when processing SYN from
socket backlog (thus possibly in process context)
Fixes: 06f877d613 ("tcp/dccp: fix other lockdep splats accessing ireq_opt")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit af7d6cce53 ]
Since commit 5aad1de5ea ("ipv4: use separate genid for next hop
exceptions"), exceptions get deprecated separately from cached
routes. In particular, administrative changes don't clear PMTU anymore.
As Stefano described in commit e9fa1495d7 ("ipv6: Reflect MTU changes
on PMTU of exceptions for MTU-less routes"), the PMTU discovered before
the local MTU change can become stale:
- if the local MTU is now lower than the PMTU, that PMTU is now
incorrect
- if the local MTU was the lowest value in the path, and is increased,
we might discover a higher PMTU
Similarly to what commit e9fa1495d7 did for IPv6, update PMTU in those
cases.
If the exception was locked, the discovered PMTU was smaller than the
minimal accepted PMTU. In that case, if the new local MTU is smaller
than the current PMTU, let PMTU discovery figure out if locking of the
exception is still needed.
To do this, we need to know the old link MTU in the NETDEV_CHANGEMTU
notifier. By the time the notifier is called, dev->mtu has been
changed. This patch adds the old MTU as additional information in the
notifier structure, and a new call_netdevice_notifiers_u32() function.
Fixes: 5aad1de5ea ("ipv4: use separate genid for next hop exceptions")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e285d5bfb7 upstream.
According to ETSI TS 102 622 specification chapter 4.4 pipe identifier
is 7 bits long which allows for 128 unique pipe IDs. Because
NFC_HCI_MAX_PIPES is used as the number of pipes supported and not
as the max pipe ID, its value should be 128 instead of 127.
nfc_hci_recv_from_llc extracts pipe ID from packet header using
NFC_HCI_FRAGMENT(0x7F) mask which allows for pipe ID value of 127.
Same happens when NCI_HCP_MSG_GET_PIPE() is being used. With
pipes array having only 127 elements and pipe ID of 127 the OOB memory
access will result.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Allen Pais <allen.pais@oracle.com>
Cc: "David S. Miller" <davem@davemloft.net>
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 86029d10af ]
This contains key material in crypto_send_aes_gcm_128 and
crypto_recv_aes_gcm_128.
Introduce union tls_crypto_context, and replace the two identical
unions directly embedded in struct tls_context with it. We can then
use this union to clean up the memory in the new tls_ctx_free()
function.
Fixes: 3c4d755915 ("tls: kernel TLS support")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces several helper functions/macros that will be
used in the follow-up patch. No runtime changes yet.
The new logic (fully implemented in the second patch) is as follows:
* Nodes in the rb-tree will now contain not single fragments, but lists
of consecutive fragments ("runs").
* At each point in time, the current "active" run at the tail is
maintained/tracked. Fragments that arrive in-order, adjacent
to the previous tail fragment, are added to this tail run without
triggering the re-balancing of the rb-tree.
* If a fragment arrives out of order with the offset _before_ the tail run,
it is inserted into the rb-tree as a single fragment.
* If a fragment arrives after the current tail fragment (with a gap),
it starts a new "tail" run, as is inserted into the rb-tree
at the end as the head of the new run.
skb->cb is used to store additional information
needed here (suggested by Eric Dumazet).
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Peter Oskolkov <posk@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 353c9cb360)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bffa72cf7f upstream
skb->rbnode shares space with skb->next, skb->prev and skb->tstamp
Current uses (TCP receive ofo queue and netem) need to save/restore
tstamp, while skb->dev is either NULL (TCP) or a constant for a given
queue (netem).
Since we plan using an RB tree for TCP retransmit queue to speedup SACK
processing with large BDP, this patch exchanges skb->dev and
skb->tstamp.
This saves some overhead in both TCP and netem.
v2: removes the swtstamp field from struct tcp_skb_cb
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Cc: Wei Wang <weiwan@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Put the read-mostly fields in a separate cache line
at the beginning of struct netns_frags, to reduce
false sharing noticed in inet_frag_kill()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit c2615cf5a7)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some users are willing to provision huge amounts of memory to be able
to perform reassembly reasonnably well under pressure.
Current memory tracking is using one atomic_t and integers.
Switch to atomic_long_t so that 64bit arches can use more than 2GB,
without any cost for 32bit arches.
Note that this patch avoids an overflow error, if high_thresh was set
to ~2GB, since this test in inet_frag_alloc() was never true :
if (... || frag_mem_limit(nf) > nf->high_thresh)
Tested:
$ echo 16000000000 >/proc/sys/net/ipv4/ipfrag_high_thresh
<frag DDOS>
$ grep FRAG /proc/net/sockstat
FRAG: inuse 14705885 memory 16000002880
$ nstat -n ; sleep 1 ; nstat | grep Reas
IpReasmReqds 3317150 0.0
IpReasmFails 3317112 0.0
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 3e67f106f6)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This refactors ip_expire() since one indentation level is removed.
Note: in the future, we should try hard to avoid the skb_clone()
since this is a serious performance cost.
Under DDOS, the ICMP message wont be sent because of rate limits.
Fact that ip6_expire_frag_queue() does not use skb_clone() is
disturbing too. Presumably IPv6 should have the same
issue than the one we fixed in commit ec4fbd6475
("inet: frag: release spinlock before calling icmp_send()")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 399d1404be)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove sum_frag_mem_limit(), ip_frag_mem() & ip6_frag_mem()
Also since we use rhashtable we can bring back the number of fragments
in "grep FRAG /proc/net/sockstat /proc/net/sockstat6" that was
removed in commit 434d305405 ("inet: frag: don't account number
of fragment queues")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 6befe4a78b)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some applications still rely on IP fragmentation, and to be fair linux
reassembly unit is not working under any serious load.
It uses static hash tables of 1024 buckets, and up to 128 items per bucket (!!!)
A work queue is supposed to garbage collect items when host is under memory
pressure, and doing a hash rebuild, changing seed used in hash computations.
This work queue blocks softirqs for up to 25 ms when doing a hash rebuild,
occurring every 5 seconds if host is under fire.
Then there is the problem of sharing this hash table for all netns.
It is time to switch to rhashtables, and allocate one of them per netns
to speedup netns dismantle, since this is a critical metric these days.
Lookup is now using RCU. A followup patch will even remove
the refcount hold/release left from prior implementation and save
a couple of atomic operations.
Before this patch, 16 cpus (16 RX queue NIC) could not handle more
than 1 Mpps frags DDOS.
After the patch, I reach 9 Mpps without any tuning, and can use up to 2GB
of storage for the fragments (exact number depends on frags being evicted
after timeout)
$ grep FRAG /proc/net/sockstat
FRAG: inuse 1966916 memory 2140004608
A followup patch will change the limits for 64bit arches.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Kirill Tkhai <ktkhai@virtuozzo.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Florian Westphal <fw@strlen.de>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Alexander Aring <alex.aring@gmail.com>
Cc: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 648700f76b)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to simplify the API, add a pointer to struct inet_frags.
This will allow us to make things less complex.
These functions no longer have a struct inet_frags parameter :
inet_frag_destroy(struct inet_frag_queue *q /*, struct inet_frags *f */)
inet_frag_put(struct inet_frag_queue *q /*, struct inet_frags *f */)
inet_frag_kill(struct inet_frag_queue *q /*, struct inet_frags *f */)
inet_frags_exit_net(struct netns_frags *nf /*, struct inet_frags *f */)
ip6_expire_frag_queue(struct net *net, struct frag_queue *fq)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 093ba72914)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We will soon initialize one rhashtable per struct netns_frags
in inet_frags_init_net().
This patch changes the return value to eventually propagate an
error.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 787bea7748)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 037b0b86ec ]
Lets not turn the TCP ULP lookup into an arbitrary module loader as
we only intend to load ULP modules through this mechanism, not other
unrelated kernel modules:
[root@bar]# cat foo.c
#include <sys/types.h>
#include <sys/socket.h>
#include <linux/tcp.h>
#include <linux/in.h>
int main(void)
{
int sock = socket(PF_INET, SOCK_STREAM, 0);
setsockopt(sock, IPPROTO_TCP, TCP_ULP, "sctp", sizeof("sctp"));
return 0;
}
[root@bar]# gcc foo.c -O2 -Wall
[root@bar]# lsmod | grep sctp
[root@bar]# ./a.out
[root@bar]# lsmod | grep sctp
sctp 1077248 4
libcrc32c 16384 3 nf_conntrack,nf_nat,sctp
[root@bar]#
Fix it by adding module alias to TCP ULP modules, so probing module
via request_module() will be limited to tcp-ulp-[name]. The existing
modules like kTLS will load fine given tcp-ulp-tls alias, but others
will fail to load:
[root@bar]# lsmod | grep sctp
[root@bar]# ./a.out
[root@bar]# lsmod | grep sctp
[root@bar]#
Sockmap is not affected from this since it's either built-in or not.
Fixes: 734942cc4e ("tcp: ULP infrastructure")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Acked-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a9ba23d48d ]
At present the ipv6_renew_options_kern() function ends up calling into
access_ok() which is problematic if done from inside an interrupt as
access_ok() calls WARN_ON_IN_IRQ() on some (all?) architectures
(x86-64 is affected). Example warning/backtrace is shown below:
WARNING: CPU: 1 PID: 3144 at lib/usercopy.c:11 _copy_from_user+0x85/0x90
...
Call Trace:
<IRQ>
ipv6_renew_option+0xb2/0xf0
ipv6_renew_options+0x26a/0x340
ipv6_renew_options_kern+0x2c/0x40
calipso_req_setattr+0x72/0xe0
netlbl_req_setattr+0x126/0x1b0
selinux_netlbl_inet_conn_request+0x80/0x100
selinux_inet_conn_request+0x6d/0xb0
security_inet_conn_request+0x32/0x50
tcp_conn_request+0x35f/0xe00
? __lock_acquire+0x250/0x16c0
? selinux_socket_sock_rcv_skb+0x1ae/0x210
? tcp_rcv_state_process+0x289/0x106b
tcp_rcv_state_process+0x289/0x106b
? tcp_v6_do_rcv+0x1a7/0x3c0
tcp_v6_do_rcv+0x1a7/0x3c0
tcp_v6_rcv+0xc82/0xcf0
ip6_input_finish+0x10d/0x690
ip6_input+0x45/0x1e0
? ip6_rcv_finish+0x1d0/0x1d0
ipv6_rcv+0x32b/0x880
? ip6_make_skb+0x1e0/0x1e0
__netif_receive_skb_core+0x6f2/0xdf0
? process_backlog+0x85/0x250
? process_backlog+0x85/0x250
? process_backlog+0xec/0x250
process_backlog+0xec/0x250
net_rx_action+0x153/0x480
__do_softirq+0xd9/0x4f7
do_softirq_own_stack+0x2a/0x40
</IRQ>
...
While not present in the backtrace, ipv6_renew_option() ends up calling
access_ok() via the following chain:
access_ok()
_copy_from_user()
copy_from_user()
ipv6_renew_option()
The fix presented in this patch is to perform the userspace copy
earlier in the call chain such that it is only called when the option
data is actually coming from userspace; that place is
do_ipv6_setsockopt(). Not only does this solve the problem seen in
the backtrace above, it also allows us to simplify the code quite a
bit by removing ipv6_renew_options_kern() completely. We also take
this opportunity to cleanup ipv6_renew_options()/ipv6_renew_option()
a small amount as well.
This patch is heavily based on a rough patch by Al Viro. I've taken
his original patch, converted a kmemdup() call in do_ipv6_setsockopt()
to a memdup_user() call, made better use of the e_inval jump target in
the same function, and cleaned up the use ipv6_renew_option() by
ipv6_renew_options().
CC: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9ce7bc036a ]
It is a waste of memory to use a full "struct netns_sysctl_ipv6"
while only one pointer is really used, considering netns_sysctl_ipv6
keeps growing.
Also, since "struct netns_frags" has cache line alignment,
it is better to move the frags_hdr pointer outside, otherwise
we spend a full cache line for this pointer.
This saves 192 bytes of memory per netns.
Fixes: c038a767cd ("ipv6: add a new namespace for nf_conntrack_reasm")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 455f05ecd2 ]
syzbot reported that we reinitialize an active delayed
work in vsock_stream_connect():
ODEBUG: init active (active state 0) object type: timer_list hint:
delayed_work_timer_fn+0x0/0x90 kernel/workqueue.c:1414
WARNING: CPU: 1 PID: 11518 at lib/debugobjects.c:329
debug_print_object+0x16a/0x210 lib/debugobjects.c:326
The pattern is apparently wrong, we should only initialize
the dealyed work once and could repeatly schedule it. So we
have to move out the initializations to allocation side.
And to avoid confusion, we can split the shared dwork
into two, instead of re-using the same one.
Fixes: d021c34405 ("VSOCK: Introduce VM Sockets")
Reported-by: <syzbot+8a9b1bd330476a4f3db6@syzkaller.appspotmail.com>
Cc: Andy king <acking@vmware.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0dcb82254d ]
llc_sap_put() decreases the refcnt before deleting sap
from the global list. Therefore, there is a chance
llc_sap_find() could find a sap with zero refcnt
in this global list.
Close this race condition by checking if refcnt is zero
or not in llc_sap_find(), if it is zero then it is being
removed so we can just treat it as gone.
Reported-by: <syzbot+278893f3f7803871f7ce@syzkaller.appspotmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9a9c9b51e5 ]
We want to add finer control of the number of ACK packets sent after
ECN events.
This patch is not changing current behavior, it only enables following
change.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a0496ef2c2 ]
Per DCTCP RFC8257 (Section 3.2) the ACK reflecting the CE status change
has to be sent immediately so the sender can respond quickly:
""" When receiving packets, the CE codepoint MUST be processed as follows:
1. If the CE codepoint is set and DCTCP.CE is false, set DCTCP.CE to
true and send an immediate ACK.
2. If the CE codepoint is not set and DCTCP.CE is true, set DCTCP.CE
to false and send an immediate ACK.
"""
Previously DCTCP implementation may continue to delay the ACK. This
patch fixes that to implement the RFC by forcing an immediate ACK.
Tested with this packetdrill script provided by Larry Brakmo
0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
0.000 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
0.000 setsockopt(3, SOL_TCP, TCP_CONGESTION, "dctcp", 5) = 0
0.000 bind(3, ..., ...) = 0
0.000 listen(3, 1) = 0
0.100 < [ect0] SEW 0:0(0) win 32792 <mss 1000,sackOK,nop,nop,nop,wscale 7>
0.100 > SE. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 8>
0.110 < [ect0] . 1:1(0) ack 1 win 257
0.200 accept(3, ..., ...) = 4
+0 setsockopt(4, SOL_SOCKET, SO_DEBUG, [1], 4) = 0
0.200 < [ect0] . 1:1001(1000) ack 1 win 257
0.200 > [ect01] . 1:1(0) ack 1001
0.200 write(4, ..., 1) = 1
0.200 > [ect01] P. 1:2(1) ack 1001
0.200 < [ect0] . 1001:2001(1000) ack 2 win 257
+0.005 < [ce] . 2001:3001(1000) ack 2 win 257
+0.000 > [ect01] . 2:2(0) ack 2001
// Previously the ACK below would be delayed by 40ms
+0.000 > [ect01] E. 2:2(0) ack 3001
+0.500 < F. 9501:9501(0) ack 4 win 257
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 27cde44a25 ]
Currently when a DCTCP receiver delays an ACK and receive a
data packet with a different CE mark from the previous one's, it
sends two immediate ACKs acking previous and latest sequences
respectly (for ECN accounting).
Previously sending the first ACK may mark off the delayed ACK timer
(tcp_event_ack_sent). This may subsequently prevent sending the
second ACK to acknowledge the latest sequence (tcp_ack_snd_check).
The culprit is that tcp_send_ack() assumes it always acknowleges
the latest sequence, which is not true for the first special ACK.
The fix is to not make the assumption in tcp_send_ack and check the
actual ack sequence before cancelling the delayed ACK. Further it's
safer to pass the ack sequence number as a local variable into
tcp_send_ack routine, instead of intercepting tp->rcv_nxt to avoid
future bugs like this.
Reported-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 24b711edfc ]
Example setup:
host: ip -6 addr add dev eth1 2001:db8:104::4
where eth1 is enslaved to a VRF
switch: ip -6 ro add 2001:db8:104::4/128 dev br1
where br1 only has an LLA
ping6 2001:db8:104::4
ssh 2001:db8:104::4
(NOTE: UDP works fine if the PKTINFO has the address set to the global
address and ifindex is set to the index of eth1 with a destination an
LLA).
For ICMP, icmp6_iif needs to be updated to check if skb->dev is an
L3 master. If it is then return the ifindex from rt6i_idev similar
to what is done for loopback.
For TCP, restore the original tcp_v6_iif definition which is needed in
most places and add a new tcp_v6_iif_l3_slave that considers the
l3_slave variability. This latter check is only needed for socket
lookups.
Fixes: 9ff7438460 ("net: vrf: Handle ipv6 multicast and link-local addresses")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 169dc027fb ]
The rol32 call is currently rotating hash but the rol'd value is
being discarded. I believe the current code is incorrect and hash
should be assigned the rotated value returned from rol32.
Thanks to David Lebrun for spotting this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bb7b40aecb upstream.
When removing a rule that jumps to chain and such chain in the same
batch, this bogusly hits EBUSY. Add activate and deactivate operations
to expression that can be called from the preparation and the
commit/abort phases.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6c206b2009 ]
After commit 6b229cf77d ("udp: add batching to udp_rmem_release()")
the sk_rmem_alloc field does not measure exactly anymore the
receive queue length, because we batch the rmem release. The issue
is really apparent only after commit 0d4a6608f6 ("udp: do rmem bulk
free even if the rx sk queue is empty"): the user space can easily
check for an empty socket with not-0 queue length reported by the 'ss'
tool or the procfs interface.
We need to use a custom UDP helper to report the correct queue length,
taking into account the forward allocation deficit.
Reported-by: trevor.francis@46labs.com
Fixes: 6b229cf77d ("UDP: add batching to udp_rmem_release()")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fa1be7e01e ]
Some of the code paths calculating flow hash for IPv6 use flowlabel member
of struct flowi6 which, despite its name, encodes both flow label and
traffic class. If traffic class changes within a TCP connection (as e.g.
ssh does), ECMP route can switch between path. It's also inconsistent with
other code paths where ip6_flowlabel() (returning only flow label) is used
to feed the key.
Use only flow label everywhere, including one place where hash key is set
using ip6_flowinfo().
Fixes: 51ebd31815 ("ipv6: add support of equal cost multipath (ECMP)")
Fixes: f70ea018da ("net: Add functions to get skb->hash based on flow structures")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b85ab56c3f ]
llc_conn_send_pdu() pushes the skb into write queue and
calls llc_conn_send_pdus() to flush them out. However, the
status of dev_queue_xmit() is not returned to caller,
in this case, llc_conn_state_process().
llc_conn_state_process() needs hold the skb no matter
success or failure, because it still uses it after that,
therefore we should hold skb before dev_queue_xmit() when
that skb is the one being processed by llc_conn_state_process().
For other callers, they can just pass NULL and ignore
the return value as they are.
Reported-by: Noam Rathaus <noamr@beyondsecurity.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d52e5a7e7c ]
Prior to the rework of PMTU information storage in commit
2c8cec5c10 ("ipv4: Cache learned PMTU information in inetpeer."),
when a PMTU event advertising a PMTU smaller than
net.ipv4.route.min_pmtu was received, we would disable setting the DF
flag on packets by locking the MTU metric, and set the PMTU to
net.ipv4.route.min_pmtu.
Since then, we don't disable DF, and set PMTU to
net.ipv4.route.min_pmtu, so the intermediate router that has this link
with a small MTU will have to drop the packets.
This patch reestablishes pre-2.6.39 behavior by splitting
rtable->rt_pmtu into a bitfield with rt_mtu_locked and rt_pmtu.
rt_mtu_locked indicates that we shouldn't set the DF bit on that path,
and is checked in ip_dont_fragment().
One possible workaround is to set net.ipv4.route.min_pmtu to a value low
enough to accommodate the lowest MTU encountered.
Fixes: 2c8cec5c10 ("ipv4: Cache learned PMTU information in inetpeer.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 657308f73e ]
Similar to the ancient commit a5fe8e7695 ("regulatory: add NUL
to alpha2"), add another byte to alpha2 in the request struct so
that when we use nla_put_string(), we don't overrun anything.
Fixes: 73d54c9e74 ("cfg80211: add regulatory netlink multicast group")
Reported-by: Kees Cook <keescook@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 651b9920d7 ]
This ensures that mac80211 allocated management frames are properly
aligned, which makes copying them more efficient.
For instance, mt76 uses iowrite32_copy to copy beacon frames to beacon
template memory on the chip.
Misaligned 32-bit accesses cause CPU exceptions on MIPS and should be
avoided.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 21706ee8a4 ]
There was a regression at some point from the intended functionality of
commit f60c3704e8 ("bonding: Fix alb mode to only use first level
vlans.")
Given the return value vlan_get_encap_level() we need to store the nest
level of the bond device, and then compare the vlan's encap level to
this. Without this, this check always fails and learning packets are
never sent.
In addition, this same commit caused a regression in the behavior of
balance_alb, which requires learning packets be sent for all interfaces
using the slave's mac in order to load balance properly. For vlan's
that have not set a user mac, we can send after checking one bit.
Otherwise we need send the set mac, albeit defeating rx load balancing
for that vlan.
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
