We have deprecated the distinction between hardware and physical
segments in the block layer. Consolidate the two limits into one in
drivers/mmc/.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
On OMAP4, MMC2 controller has eMMC which draws power from VAUX regulator
on TWL. Though the eMMC supports dual voltage[1.8v/3v] as per ocr register,
its VCC is fixed at 3V for operation. With this once the mmc core selects
the minimum voltage[1.8] supported based on the ocr value read from OCR register,
eMMC will not get detected. Thus the platform data for MMC2 is updated with ocr
mask and same will be communicated to core which will set the regulator to
always operate at 3V when ever turned ON.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In OMAP4, as per new PM programming model, the legacy registers
which were there in OMAP3 are all shifted by 0x100 while new one's
are added from offset 0 to 0x10.
For OMAP4, the register offset appending of 0x100 done in devices.c
currently, is moved to driver file.This change fits in for current
implementation as well as once the driver undergoes hwmod adaptation.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap4 es2 hsmmc has a updated soft reset logic.After the
reset is issued monitor a 0->1 transition first. The reset of
CMD or DATA lines is complete only after a 0->1->0 transition
of SRC or SRD bits.
Signed-off-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Tested-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
wires variable is renamed, extended and this single variable to be used to
pass the platform capabilities, e.g DDR mode. Also removed the hardcoded
value was using as bus-width.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If suspend called when kmmcd is doing host->ops->disable, as kmmcd already
increased host->en_dis_recurs to 1, the mmc_host_enable in suspend
function will return directly without increase the nesting_cnt, which will
cause the followed register access carried out to the disabled host.
mmc_suspend_host will enable host itself. No need to enable host before
it. Also works on kmmcd will get flushed in mmc_suspend_host, enable host
after it will be safe. So make the mmc_host_enable after it.
[cjb: rebase against current Linus]
Signed-off-by: Ethan <ethan.too@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Acked-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes the following warning:
drivers/mmc/host/omap_hsmmc.c: In function 'omap_hsmmc_suspend':
drivers/mmc/host/omap_hsmmc.c:2275: warning: unused variable 'state'
Introduced by commit ID:
commit 1a13f8fa76
Author: Matt Fleming <matt@console-pimps.org>
Date: Wed May 26 14:42:08 2010 -0700
mmc: remove the "state" argument to mmc_suspend_host()
The unique usage of this var was removed there, and missed
removing the respective declaration aswell.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Acked-by: Matt Fleming <matt@console-pimps.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If other informative interrupts are enabled for the DMA channel used by
hsmmc, those are incorrectly treated as block completion. This patch lets
only the block completion interrupt to be processed.
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Even though many mmc host drivers pass a pm_message_t argument to
mmc_suspend_host() that argument isn't used the by MMC core. As host
drivers are converted to dev_pm_ops they'll have to construct
pm_message_t's (as they won't be passed by the PM subsystem any more) just
to appease the mmc suspend interface.
We might as well just delete the unused paramter.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Michal Miroslaw <mirq-linux@rere.qmqm.pl>ZZ
Acked-by: Sascha Sommer <saschasommer@freenet.de>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert PM operations to use dev_pm_ops. This will facilitate the runtime
PM coversion which will add to dev_pm_ops hooks.
Note that dev_pm_ops version of the suspend hook no longer takes a 'state'
argument. However, the MMC core function mmc_suspend_host() still takes a
'state' argument, but it is unused, so a dummy state variable was created
to pass to the MMC core.
In the future, the MMC core should be converted to drop this state
argument and the rest of the MMC drivers could be easily converted to
dev_pm_ops as well.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The following changes were needed:
- do not use in_interrupt() because it will not work
with threaded interrupts
In addition, the following improvements were made:
- ensure DMA is unmapped only after the final DMA interrupt
- ensure a request is completed only after the final DMA interrupt
- disable controller interrupts when a request is not in progress
- remove the spin-lock protecting the start of a new request from
an unexpected interrupt because the locking was complicated and
a 'req_in_progress' flag suffices (since the spin-lock only defers
the unexpected interrupts anyway)
- instead use the spin-lock to protect the MMC interrupt handler
from the DMA interrupt handler
- remove the semaphore preventing DMA from being started while
the previous DMA is still in progress - the other changes make that
impossible, so it is now a BUG_ON condition
- ensure the controller interrupt status is clear before exiting
the interrrupt handler
In general, these changes make the code safer but do not fix any specific
bugs so backporting is not necessary.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Tested-by: Venkatraman S <svenkatr@ti.com>
Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The reset of data lines when the card is removed from the cage results in
a failure.The failure is seen if the card is removed from the cage when TC
is pending after a CMD with data received CC.The reset logic leaves the
controller in a state where niether a TC is received nor DTO.
The rest code can be safely removed here since it is taken care in the IRQ
handler.
Signed-off-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is still possible to use the omap_hsmmc module
without the regulator framework. Accordingly, ifdef
out regulator-specific functions.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
EMMC can have two voltage supplies, Vcc and VccQ
which are implemented in the code as consumer
supplies vmmc and vmmc_aux.
If the regulator that supplies vmmc_aux is shared
with other consumers, then sending it to sleep
will disrupt those consumers. However, the
TWL4030-family regulators may have OFF remapped
to SLEEP, in which case 'regulator_disable()'
will put the regulator to sleep only when all
consumers are disabled - which is the desired
behaviour.
This patch adds a platform data field to allow
that option.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Stop using 'regulator_is_enabled()' and just pair enables
with disables so that the regulator reference counts can
work correctly.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
An eMMC may be always powered on, so that the lowest
power saving state possible is sleeping. Add a field
to the platform data to indicate that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch moves the setup code for GPIO's and Voltage
Regulators from the board file mmc-twl4030.c to the
driver omap_hsmmc.c. PBIAS and other system control
configuration remains in the board file.
Moving GPIO code to the driver makes the board initialisation
code independent of when GPIO's are defined. That makes the
board initialisation now entirely independent of its original
twl4030 roots.
Moving Voltage Regulator code to the driver allows for further
development of regulator support in the core MMC code. It also
permits the MMC core to be compiled as a module, because the
board code no longer calls MMC core functions.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (417 commits)
MAINTAINERS: EB110ATX is not ebsa110
MAINTAINERS: update Eric Miao's email address and status
fb: add support of LCD display controller on pxa168/910 (base layer)
[ARM] 5552/1: ep93xx get_uart_rate(): use EP93XX_SYSCON_PWRCNT and EP93XX_SYSCON_PWRCN
[ARM] pxa/sharpsl_pm: zaurus needs generic pxa suspend/resume routines
[ARM] 5544/1: Trust PrimeCell resource sizes
[ARM] pxa/sharpsl_pm: cleanup of gpio-related code.
[ARM] pxa/sharpsl_pm: drop set_irq_type calls
[ARM] pxa/sharpsl_pm: merge pxa-specific code into generic one
[ARM] pxa/sharpsl_pm: merge the two sharpsl_pm.c since it's now pxa specific
[ARM] sa1100: remove unused collie_pm.c
[ARM] pxa: fix the conflicting non-static declarations of global_gpios[]
[ARM] 5550/1: Add default configure file for w90p910 platform
[ARM] 5549/1: Add clock api for w90p910 platform.
[ARM] 5548/1: Add gpio api for w90p910 platform
[ARM] 5551/1: Add multi-function pin api for w90p910 platform.
[ARM] Make ARM_VIC_NR depend on ARM_VIC
[ARM] 5546/1: ARM PL022 SSP/SPI driver v3
ARM: OMAP4: SMP: Update defconfig for OMAP4430
ARM: OMAP4: SMP: Enable SMP support for OMAP4430
...
Decouple the HSMMC glue from the twl4030 as the only
regulator provider, using the regulator framework instead.
This makes the glue's "mmc-twl4030" name become a complete
misnomer ... this code could probably all migrate into the
HSMMC driver now.
Tested on 3430SDP (SD and low-voltage MMC) and Beagle (SD),
plus some other boards (including Overo) after they were
converted to set up MMC regulators properly.
Eventually all boards should just associate a regulator with
each MMC controller they use. In some cases (Overo MMC2 and
Pandora MMC3, at least) that would be a fixed-voltage regulator
with no real software control. As a temporary hack (pending
regulator-next updates to make the "fixed.c" regulator become
usable) there's a new ocr_mask field for those boards.
Patch updated with a fix for disabling vcc_aux by
Adrian Hunter <adrian.hunter@nokia.com>
Cc: Pierre Ossman <drzeus-list@drzeus.cx>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
