[ Upstream commit d968f0f2e4 ]
Latest change in open-lldp code uses bytes 6-11 of perm_addr buffer
as the Ethernet source address for the host TLV packet.
Since our driver does not fill these bytes, they stay at zero and
the open-lldp code ends up sending the TLV packet with zero source
address and the switch drops this packet.
The fix is to initialize these bytes to 0xff. The open-lldp code
considers 0xff:ff:ff:ff:ff:ff as the invalid address and falls back to
use the host's mac address as the Ethernet source address.
Fixes: 3a6a931dfb ("net/mlx5e: Support DCBX CEE API")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8ff93de766 ]
Symbol error during carrier counter from PPCNT was mistakenly reported as
TX carrier errors in get_stats ndo, although it's an RX counter.
Fixes: 269e6b3af3 ("net/mlx5e: Report additional error statistics in get stats ndo")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2a0165a034 ]
Draining the health workqueue will ignore future health works including
the one that report hardware failure and thus we can't enter error state
Instead cancel the recovery flow and make sure only recovery flow won't
be scheduled.
Fixes: 5e44fca504 ('net/mlx5: Only cancel recovery work when cleaning up device')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6c780a0267 ]
Before attempting to initialize the command interface we must wait till
the fw_initializing bit is clear.
If we fail to meet this condition the hardware will drop our
configuration, specifically the descriptors page address. This scenario
can happen when the firmware is still executing an FLR flow and did not
finish yet so the driver needs to wait for that to finish.
Fixes: e3297246c2 ('net/mlx5_core: Wait for FW readiness on startup')
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 31ac93386d ]
The error flow of mlx5e_create_netdev calls the cleanup call
of the given profile without checking if it exists, fix that.
Currently the VF reps don't register that callback and we crash
if getting into error -- can be reproduced by the user doing ctrl^C
while attempting to change the sriov mode from legacy to switchdev.
Fixes: 26e59d8077 '(net/mlx5e: Implement mlx5e interface attach/detach callbacks')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Sabrina Dubroca <sdubroca@redhat.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5f195c2c5c ]
The offending commit only changed the code path for PF/VF, but it
didn't take care of VF representors. As a result, since
params->tx_min_inline_mode for VF representors is kzalloced to 0
(MLX5_INLINE_MODE_NONE), all VF reps SQs were set to that mode.
This actually works on CX5 by default but broke CX4. Fix that by
adding a call to query the min inline mode from the VF rep build up code.
Fixes: a6f402e499 ("net/mlx5e: Tx, no inline copy on ConnectX-5")
Signed-off-by: Chris Mi <chrism@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 91828bd899 ]
When the page size isn't bigger than 4K, there is no added value of enabling 4K
UAR feature in the Firmware.
Modified the condition of enabling the 4K UAR accordingly.
Fixes: f502d83495 ("net/mlx5: Activate support for 4K UARs")
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 53acd76ce5 ]
DIM (Dynamically-tuned Interrupt Moderation) is a mechanism designed for
changing the channel interrupt moderation values in order to reduce CPU
overhead for all traffic types.
Each iteration of the algorithm, DIM calculates the difference in
throughput, packet rate and interrupt rate from last iteration in order
to make a decision. DIM relies on counters for each metric. When these
counters get to their type's max value they wraparound. In this case
the delta between 'end' and 'start' samples is negative and when
translated to unsigned integers - very high. This results in a false
indication to the algorithm and might result in a wrong decision.
The fix calculates the 'distance' between 'end' and 'start' samples in a
cyclic way around the relevant type's max value. It can also be viewed as
an absolute value around the type's max value instead of around 0.
Testing show higher stability in DIM profile selection and no wraparound
issues.
Fixes: cb3c7fd4f8 ("net/mlx5e: Support adaptive RX coalescing")
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c3164d2fc4 ]
DIM (Dynamically-tuned Interrupt Moderation) is a mechanism designed for
changing the channel interrupt moderation values in order to reduce CPU
overhead for all traffic types.
Until now only interrupt and packet rate were sampled.
We found a scenario on which we get a false indication since a change in
DIM caused more aggregation and reduced packet rate while increasing BW.
We now regard a change as succesfull iff:
current_BW > (prev_BW + threshold) or
current_BW ~= prev_BW and current_PR > (prev_PR + threshold) or
current_BW ~= prev_BW and current_PR ~= prev_PR and
current_IR < (prev_IR - threshold)
Where BW = Bandwidth, PR = Packet rate and IR = Interrupt rate
Improvements (ConnectX-4Lx 25GbE, single RX queue, LRO off)
--------------------------------------------------
packet size | before[Mb/s] | after[Mb/s] | gain |
2B | 343.4 | 359.4 | 4.5% |
16B | 2739.7 | 2814.8 | 2.7% |
64B | 9739 | 10185.3 | 4.5% |
Fixes: cb3c7fd4f8 ("net/mlx5e: Support adaptive RX coalescing")
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f729860a17 ]
Remove the following module event counters out of ethtool stats. The
reason for removing these event counters is that these events do not
occur without techinician's intervention.
module_pwr_budget_exd
module_long_range
module_no_eeprom
module_enforce_part
module_unknown_id
module_unknown_status
module_plug
Fixes: bedb7c909c ("net/mlx5e: Add port module event counters to ethtool stats")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 73dd3a4839 ]
Currently when firmware command gets stuck or it takes long time to
complete, the driver command will get timeout and the command slot is
freed and can be used for new commands, and if the firmware receive new
command on the old busy slot its behavior is unexpected and this could
be harmful.
To fix this when the driver command gets timeout we return failure,
but we don't free the command slot and we wait for the firmware to
explicitly respond to that command.
Once all the entries are busy we will stop processing new firmware
commands.
Fixes: 9cba4ebcf3 ('net/mlx5: Fix potential deadlock in command mode change')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e3c1950371 ]
Pause bit should set when RX pause is on, not TX pause.
Also, setting Asym_Pause is incorrect, and should be turned off.
Fixes: 665bc53969 ("net/mlx5e: Use new ethtool get/set link ksettings API")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2017-04-22
This series contains some mlx5 fixes for net.
For your convenience, the series doesn't introduce any conflict with
the ongoing net-next pull request.
Please pull and let me know if there's any problem.
For -stable:
("net/mlx5: E-Switch, Correctly deal with inline mode on ConnectX-5") kernels >= 4.10
("net/mlx5e: Fix ETHTOOL_GRXCLSRLALL handling") kernels >= 4.8
("net/mlx5e: Fix small packet threshold") kernels >= 4.7
("net/mlx5: Fix driver load bad flow when having fw initializing timeout") kernels >= 4.4
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We have observed a sudden spike in rx/tx_packets and rx/tx_bytes
reported under /proc/net/dev. There is a race in mlx5e_update_stats()
and some of the get-stats functions (the one that we hit is the
mlx5e_get_stats() which is called by ndo_get_stats64()).
In particular, the very first thing mlx5e_update_sw_counters()
does is 'memset(s, 0, sizeof(*s))'. For example, if mlx5e_get_stats()
is unlucky at one point, rx_bytes and rx_packets could be 0. One second
later, a normal (and much bigger than 0) value will be reported.
This patch is to use a 'struct mlx5e_sw_stats temp' to avoid
a direct memset zero on priv->stats.sw.
mlx5e_update_vport_counters() has a similar race. Hence, addressed
together. However, memset zero is removed instead because
it is not needed.
I am lucky enough to catch this 0-reset in rx multicast:
eth0: 41457665 76804 70 0 0 70 0 47085 15586634 87502 3 0 0 0 3 0
eth0: 41459860 76815 70 0 0 70 0 47094 15588376 87516 3 0 0 0 3 0
eth0: 41460577 76822 70 0 0 70 0 0 15589083 87521 3 0 0 0 3 0
eth0: 41463293 76838 70 0 0 70 0 47108 15595872 87538 3 0 0 0 3 0
eth0: 41463379 76839 70 0 0 70 0 47116 15596138 87539 3 0 0 0 3 0
v2: Remove memset zero from mlx5e_update_vport_counters()
v1: Use temp and memcpy
Fixes: 9218b44dcc ("net/mlx5e: Statistics handling refactoring")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Suggested-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handler for ETHTOOL_GRXCLSRLALL must set info->data to the size
of the table, regardless of the amount of entries in it.
Existing code does not do that, and this breaks all usage of ethtool -N
or -n without explicit location, with this error:
rmgr: Invalid RX class rules table size: Success
Set info->data to the table size.
Tested:
ethtool -n ens8
ethtool -N ens8 flow-type ip4 src-ip 1.1.1.1 dst-ip 2.2.2.2 action 1
ethtool -N ens8 flow-type ip4 src-ip 1.1.1.1 dst-ip 2.2.2.2 action 1 loc 55
ethtool -n ens8
ethtool -N ens8 delete 1023
ethtool -N ens8 delete 55
Fixes: f913a72aa0 ("net/mlx5e: Add support to get ethtool flow rules")
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
RX packet headers are meant to be contained in SKB linear part,
and chose a threshold of 128.
It turns out this is not enough, i.e. for IPv6 packet over VxLAN.
In this case, UDP/IPv4 needs 42 bytes, GENEVE header is 8 bytes,
and 86 bytes for TCP/IPv6. In total 136 bytes that is more than
current 128 bytes. In this case expand header flow is reached.
The warning in skb_try_coalesce() caused by a wrong truesize
was already fixed here:
commit 158f323b98 ("net: adjust skb->truesize in pskb_expand_head()").
Still, we prefer to totally avoid the expand header flow for performance reasons.
Tested regular TCP_STREAM with iperf for 1 and 8 streams, no degradation was found.
Fixes: 461017cb00 ("net/mlx5e: Support RX multi-packet WQE (Striding RQ)")
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When UAR is released, we deallocate the device resource, but
don't unmmap the UAR mapping memory.
Fix the leak by unmapping this memory.
Fixes: a6d51b6861 ('net/mlx5: Introduce blue flame register allocator)
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Otherwise the code that fills the ipv6 encapsulation headers could be writing
beyond the allocated headers buffer.
Fixes: ce99f6b97f ('net/mlx5e: Support SRIOV TC encapsulation offloads for IPv6 tunnels')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Otherwise the code that fills the ipv4 encapsulation headers could be writing
beyond the allocated headers buffer.
Fixes: a54e20b4fc ('net/mlx5e: Add basic TC tunnel set action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
On ConnectX5 the wqe inline mode is "none" and hence the FW
reports MLX5_CAP_INLINE_MODE_NOT_REQUIRED.
Fix our devlink callbacks to deal with that on get and set.
Also fix the tc flow parsing code not to fail anything when
inline isn't required.
Fixes: bffaa91658 ('net/mlx5: E-Switch, Add control for inline mode')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
If FW is stuck in initializing state we will skip the driver load, but
current error handling flow doesn't clean previously allocated command
interface resources.
Fixes: e3297246c2 ('net/mlx5_core: Wait for FW readiness on startup')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
In NETDEV_CHANGEUPPER event the upper_info field is valid
only when linking is true. Otherwise it should be ignored.
Fixes: 7907f23adc (net/mlx5: Implement RoCE LAG feature)
Signed-off-by: Talat Batheesh <talatb@mellanox.com>
Reviewed-by: Aviv Heller <avivh@mellanox.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX packets statistics ('rx_packets' counter) used to count LRO packets
as one, even though it contains multiple segments.
This patch will increment the counter by the number of segments, and
align the driver with the behavior of other drivers in the stack.
Note that no information is lost in this patch due to 'rx_lro_packets'
counter existence.
Before, ethtool showed:
$ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets"
rx_packets: 435277
rx_lro_packets: 35847
rx_packets_phy: 1935066
Now, we will see the more logical statistics:
$ ethtool -S ens6 | egrep "rx_packets|rx_lro_packets"
rx_packets: 1935066
rx_lro_packets: 35847
rx_packets_phy: 1935066
Fixes: e586b3b0ba ("net/mlx5: Ethernet Datapath files")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX packets statistics ('tx_packets' counter) used to count GSO packets
as one, even though it contains multiple segments.
This patch will increment the counter by the number of segments, and
align the driver with the behavior of other drivers in the stack.
Note that no information is lost in this patch due to 'tx_tso_packets'
counter existence.
Before, ethtool showed:
$ ethtool -S ens6 | egrep "tx_packets|tx_tso_packets"
tx_packets: 61340
tx_tso_packets: 60954
tx_packets_phy: 2451115
Now, we will see the more logical statistics:
$ ethtool -S ens6 | egrep "tx_packets|tx_tso_packets"
tx_packets: 2451115
tx_tso_packets: 60954
tx_packets_phy: 2451115
Fixes: e586b3b0ba ("net/mlx5: Ethernet Datapath files")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With ConnectX-4 sharing SRQs from the same space as QPs, we hit a
limit preventing some applications to allocate needed QPs amount.
Double the size to 256K.
Fixes: e126ba97db ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was added to allow the TC offloading code to identify offloading
encap/decap vxlan rules.
The VF reps are effectively related to the same mlx5 PCI device as the
PF. Since the kernel invokes the (say) delete ndo for each netdev, the
FW erred on multiple vxlan dst port deletes when the port was deleted
from the system.
We fix that by keeping the registration to be carried out only by the
PF. Since the PF serves as the uplink device, the VF reps will look
up a port there and realize if they are ok to offload that.
Tested:
<SETUP VFS>
<SETUP switchdev mode to have representors>
ip link add vxlan1 type vxlan id 44 dev ens5f0 dstport 9999
ip link set vxlan1 up
ip link del dev vxlan1
Fixes: 4a25730eb2 ('net/mlx5e: Add ndo_udp_tunnel_add to VF representors')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we use the non UAPI values and we miss erring on
the modify action which is not supported, fix that.
Fixes: 8b32580df1 ('net/mlx5e: Add TC vlan action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the eswitch inline mode can potentially cause already configured
flows not to match the policy. E.g. set policy L4, add some L4 rules,
set policy to L2 --> bad! Hence we disallow it.
Keep track of how many offloaded rules are now set and refuse
inline mode changes if this isn't zero.
Fixes: bffaa91658 ("net/mlx5: E-Switch, Add control for inline mode")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the code to deal with add/del TC rules to have handler per NIC/E-switch
offloading use case, and push the latter into the e-switch code. This provides
better separation and is to be used in down-stream patch for applying a fix.
Fixes: bffaa91658 ("net/mlx5: E-Switch, Add control for inline mode")
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch cases for the rate limit set and query commands were
missing, which could get us wrong under fw error or driver reset
flow, fix that.
Fixes: 1466cc5b23 ('net/mlx5: Rate limit tables support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change packet type handler to ETH_P_IP instead of ETH_P_ALL
since we are already expecting an IP packet.
Also, using ETH_P_ALL will cause the loopback test packet type handler
to be called on all outgoing packets, especially our own self loopback
test SKB, which will be validated on xmit as well, and we don't want that.
Tested with:
ethtool -t ethX
validated that the loopback test passes.
Fixes: 0952da791c ('net/mlx5e: Add support for loopback selftest')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When deleting offloaded TC flows, we must correctly identify E-switch
rules. The current check could get us wrong w.r.t to rules set on the
PF. Since it's possible to set NIC rules on the PF, switch to SRIOV
offloads mode and then attempt to delete a NIC rule.
To solve that, we add a flags field to offloaded rules, set it on
creation time and use that over the code where currently needed.
Fixes: 8b32580df1 ('net/mlx5e: Add TC vlan action for SRIOV offloads')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the function setdcbx fails if the request dcbx mode
is either IEEE or CEE. We remove the IEEE/CEE mode check because
we support both IEEE and CEE interfaces.
Fixes: 3a6a931dfb ("net/mlx5e: Support DCBX CEE API")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a PCI error is detected the PCI state could be corrupt, don't save
it in that flow. Save the state after initialization. After restoring the
PCI state during slot reset save it again, restoring the state destroys
the previously saved state info.
Fixes: 05ac2c0b74 ('net/mlx5: Fix race between PCI error handlers and
health work')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The autogroups list is a list of non overlapping group boundaries
sorted by their start index. If the autogroups list wasn't empty
and an empty group slot was found at the start of the list,
the new group was added to the end of the list instead of the
beginning, as the prev initializer was incorrect.
When this was repeated, it caused multiple groups to have
overlapping boundaries.
Fixed that by correctly initializing the prev pointer to the
start of the list.
Fixes: eccec8da3b ('net/mlx5: Keep autogroups list ordered')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethernet support now calls directly into the ipv6 core code, which
fails if IPV6 is a loadable module but mlx5 is built-in:
drivers/net/ethernet/mellanox/mlx5/core/en_tc.o: In function `mlx5e_create_encap_header_ipv6':
en_tc.c:(.text.mlx5e_create_encap_header_ipv6+0x110): undefined reference to `ip6_route_output_flags'
This adds a dependency to ensure that MLX5_CORE_EN can only be built
if we are able link the kernel successfully. The downside is that the
ethernet option can be hidden. Alternatively we could make MLX5_CORE
depend on "IPV6 || !IPV6", which would force MLX5_CORE to be a module
when IPV6 is, including in configurations where we don't use the ethernet
support at all.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Some 'const'ing in qlogic networking drivers, from Bhumika Goyal.
2) Fix scheduling while atomic in l2tp network namespace exit by
deferring the work to the workqueue. From Ridge Kennedy.
3) Fix use after free in dccp timewait handling, from Andrey Ryabinin.
4) mlx5e CQE compression engine not initialized properly, from Tariq
Toukan.
5) Some UAPI header fixes from Dmitry V. Levin.
6) Don't overwrite module parameter value in mlx4 driver, from Majd
Dibbiny.
7) Fix divide by zero in xt_hashlimit netfilter module, from Alban
Browaeys.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits)
bpf: Fix bpf_xdp_event_output
net/mlx4_en: Use __skb_fill_page_desc()
net/mlx4_core: Use cq quota in SRIOV when creating completion EQs
net/mlx4_core: Fix VF overwrite of module param which disables DMFS on new probed PFs
net/mlx4: Spoofcheck and zero MAC can't coexist
net/mlx4: Change ENOTSUPP to EOPNOTSUPP
uapi: fix linux/rds.h userspace compilation errors
uapi: fix linux/seg6.h and linux/seg6_iptunnel.h userspace compilation errors
lib: Remove string from parman config selection
forcedeth: Remove return from a void function
bpf: fix spelling mistake: "proccessed" -> "processed"
uapi: fix linux/llc.h userspace compilation error
uapi: fix linux/ip6_tunnel.h userspace compilation errors
net/mlx5e: Fix wrong CQE decompression
net/mlx5e: Update MPWQE stride size when modifying CQE compress state
net/mlx5e: Fix broken CQE compression initialization
net/mlx5e: Do not reduce LRO WQE size when not using build_skb
net/mlx5e: Register/unregister vport representors on interface attach/detach
net/mlx5e: s390 system compilation fix
tcp: account for ts offset only if tsecr not zero
...
Pull Mellanox rdma updates from Doug Ledford:
"Mellanox specific updates for 4.11 merge window
Because the Mellanox code required being based on a net-next tree, I
keept it separate from the remainder of the RDMA stack submission that
is based on 4.10-rc3.
This branch contains:
- Various mlx4 and mlx5 fixes and minor changes
- Support for adding a tag match rule to flow specs
- Support for cvlan offload operation for raw ethernet QPs
- A change to the core IB code to recognize raw eth capabilities and
enumerate them (touches non-Mellanox code)
- Implicit On-Demand Paging memory registration support"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (40 commits)
IB/mlx5: Fix configuration of port capabilities
IB/mlx4: Take source GID by index from HW GID table
IB/mlx5: Fix blue flame buffer size calculation
IB/mlx4: Remove unused variable from function declaration
IB: Query ports via the core instead of direct into the driver
IB: Add protocol for USNIC
IB/mlx4: Support raw packet protocol
IB/mlx5: Support raw packet protocol
IB/core: Add raw packet protocol
IB/mlx5: Add implicit MR support
IB/mlx5: Expose MR cache for mlx5_ib
IB/mlx5: Add null_mkey access
IB/umem: Indicate that process is being terminated
IB/umem: Update on demand page (ODP) support
IB/core: Add implicit MR flag
IB/mlx5: Support creation of a WQ with scatter FCS offload
IB/mlx5: Enable QP creation with cvlan offload
IB/mlx5: Enable WQ creation and modification with cvlan offload
IB/mlx5: Expose vlan offloads capabilities
IB/uverbs: Enable QP creation with cvlan offload
...
In cqe compression with striding RQ, the decompression of the CQE field
wqe_counter was done with a wrong wraparound value.
This caused handling cqes with a wrong pointer to wqe (rx descriptor)
and creating SKBs with wrong data, pointing to wrong (and already consumed)
strides/pages.
The meaning of the CQE field wqe_counter in striding RQ holds the
stride index instead of the WQE index. Hence, when decompressing
a CQE, wqe_counter should have wrapped-around the number of strides
in a single multi-packet WQE.
We dropped this wrap-around mask at all in CQE decompression of striding
RQ. It is not needed as in such cases the CQE compression session would
break because of different value of wqe_id field, starting a new
compression session.
Tested:
ethtool -K ethxx lro off/on
ethtool --set-priv-flags ethxx rx_cqe_compress on
super_netperf 16 {ipv4,ipv6} -t TCP_STREAM -m 50 -D
verified no csum errors and no page refcount issues.
Fixes: 7219ab34f1 ("net/mlx5e: CQE compression")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reported-by: Tom Herbert <tom@herbertland.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the admin enables/disables cqe compression, updating
mpwqe stride size is required:
CQE compress ON ==> stride size = 256B
CQE compress OFF ==> stride size = 64B
This is already done on driver load via mlx5e_set_rq_type_params, all we
need is just to call it on arbitrary admin changes of cqe compression
state via priv flags or when changing timestamping state
(as it is mutually exclusive with cqe compression).
This bug introduces no functional damage, it only makes cqe compression
occur less often, since in ConnectX4-LX CQE compression is performed
only on packets smaller than stride size.
Tested:
ethtool --set-priv-flags ethxx rx_cqe_compress on
pktgen with 64 < pkt size < 256 and netperf TCP_STREAM (IPv4/IPv6)
verify `ethtool -S ethxx | grep compress` are advancing more often
(rapidly)
Fixes: 7219ab34f1 ("net/mlx5e: CQE compression")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of RQ type parameters are derived from CQE compression state flag,
CQE compression flag was initialized only after RQ type parameters
setup. This leads to load RQ with stride size smaller than what we
want for when CQE compression is on.
This bug introduces no functional damage, it only makes CQE compression
occur less often, since in ConnectX4-LX CQE compression is performed
only on packets smaller than stride size.
Fix this by marking default status of CQE compression in PFLAG prior to
calling mlx5e_set_rq_priv_params(), as it inits some fields based on it.
Tested:
load driver on systems where rx CQE compress will be on (MH)
pktgen with 64 < pkt size < 256 and netperf TCP_STREAM (IPv4/IPv6)
verify `ethtool -S ethxx | grep compress` are advancing more often
(rapidly)
Fixes: 2fc4bfb725 ("net/mlx5e: Dynamic RQ type infrastructure")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When rq_type is Striding RQ, no room of SKB_RESERVE is needed
as SKB allocation is not done via build_skb.
Fixes: e4b8550807 ("net/mlx5e: Slightly reduce hardware LRO size")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently vport representors are added only on driver load and removed on
driver unload. Apparently we forgot to handle them when we added the
seamless reset flow feature. This caused to leave the representors
netdevs alive and active with open HW resources on pci shutdown and on
error reset flows.
To overcome this we move their handling to interface attach/detach, so
they would be cleaned up on shutdown and recreated on reset flows.
Fixes: 26e59d8077 ("net/mlx5e: Implement mlx5e interface attach/detach callbacks")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When called by HW offloading drivers, the TC action (e.g
net/sched/act_mirred.c) code uses this_cpu logic, e.g
_bstats_cpu_update(this_cpu_ptr(a->cpu_bstats), bytes, packets)
per the kernel documention, preemption should be disabled, add that.
Before the fix, when running with CONFIG_PREEMPT set, we get a
BUG: using smp_processor_id() in preemptible [00000000] code: tc/3793
asserion from the TC action (mirred) stats_update callback.
Fixes: aad7e08d39 ('net/mlx5e: Hardware offloaded flower filter statistics support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow rules with same match criteria and value should be mapped to
the same flow table entry regardless the flow tag identifier.
Flow tag is part of flow table entry context and not of the
destination, therefore we should return error when we try to add
destination to flow table entry with different flow tag.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Saeed Mahameed says:
====================
mlx5-updates-2017-01-31
This series includes some updates to mlx5 core and ethernet driver.
We got one patch from Or to fix some static checker warnings.
2nd patche from Dan came to add the support for 128B cache line
in the HCA, which will configures the hardware to use 128B alignment only
on systems with 128B cache lines, otherwise it will be kept as the current
default of 64B.
From me three patches to support no inline copy on TX on ConnectX-5 and
later HCAs. Starting with two small infrastructure changes and
refactoring patches followed by two patches to add the actual support for
both xmit ndo and XDP xmit routines.
Last patch is a simple fix to return a mistakenly removed pointer from the
SQ structure, which was remove in previous submission of mlx5 4K UAR.
Saeed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
