[why]
When populating dml pipes, odm combine policy should be assigned based
on the pipe topology of the context passed in. DML pipes could be
repopulated multiple times during single validate bandwidth attempt. We
need to make sure that whenever we repopulate the dml pipes it is always
aligned with the updated context. There is a case where DML pipes get
repopulated during FPO optimization after ODM combine policy is changed.
Since in the current code we reinitlaize ODM combine policy, even though
the current context has ODM combine enabled, we overwrite it despite the
pipes are already split. This causes DML to think that MPC combine is
used so we mistakenly enable MPC combine because we apply pipe split
with ODM combine policy reset. This issue doesn't impact non windowed
MPO with ODM case because the legacy policy has restricted use cases. We
don't encounter the case where both ODM and FPO optimizations are
enabled together. So we decide to leave it as is because it is about to
be replaced anyway.
Cc: stable@vger.kernel.org # 6.6+
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Only required if FIXED_VS retimer does not support DP2-capable.
[HOW]
Gate link rate toggle with DP 128b/132b LTTPR channel coding cap check.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The New sequence has been in use in DCN314 with no regressions
introduced. Therefore, it is safe to enable this sequence for all
devices using FIXED_VS retimers. So, remove the legacy codepath and its
associated config flag.
Reviewed-by: Ovidiu Bunea <ovidiu.bunea@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We want programs besides the compositor to be able to enable or disable
panel power saving features. However, since they are currently only
configurable through DRM properties, that isn't possible. So, to remedy
that issue introduce a new "panel_power_savings" sysfs attribute.
v2: squash in fix from Hamza (Alex)
Cc: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Tested-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
'panel_cntl' structure used to control the display panel could be null,
dereferencing it could lead to a null pointer access.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/hwss/dcn21/dcn21_hwseq.c:269 dcn21_set_backlight_level() error: we previously assumed 'panel_cntl' could be null (see line 250)
Fixes: 474ac4a875 ("drm/amd/display: Implement some asic specific abm call backs.")
Cc: Yongqiang Sun <yongqiang.sun@amd.com>
Cc: Anthony Koo <Anthony.Koo@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The error message buffer overflow 'dc->links' 12 <= 12 suggests that the
code is trying to access an element of the dc->links array that is
beyond its bounds. In C, arrays are zero-indexed, so an array with 12
elements has valid indices from 0 to 11. Trying to access dc->links[12]
would be an attempt to access the 13th element of a 12-element array,
which is a buffer overflow.
To fix this, ensure that the loop does not go beyond the last valid
index when accessing dc->links[i + 1] by subtracting 1 from the loop
condition.
This would ensure that i + 1 is always a valid index in the array.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dp_dpia_bw.c:208 get_host_router_total_dp_tunnel_bw() error: buffer overflow 'dc->links' 12 <= 12
Fixes: 59f1622a5f ("drm/amd/display: Add dpia display mode validation logic")
Cc: PeiChen Huang <peichen.huang@amd.com>
Cc: Aric Cyr <aric.cyr@amd.com>
Cc: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On 14us for exit latency time causes underflow for 8K monitor with HDR on.
Increasing the latency to 28us fixes the underflow.
[How]
Increase the latency to 28us. This workaround should be sufficient
before we figure out why SR exit so long.
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Nicholas Susanto <nicholas.susanto@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Originally, PMFW said min FCLK is 300Mhz, but min DCFCLK can be increased
to 400Mhz because min FCLK is now 600Mhz so FCLK >= 1.5 * DCFCLK hardware
requirement will still be satisfied. Increasing min DCFCLK addresses
underflow issues (underflow occurs when phantom pipe is turned on for some
Sub-Viewport configs).
[how]
Increasing DCFCLK by raising the min_dcfclk_mhz
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Sohaib Nadeem <sohaib.nadeem@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The error message buffer overflow 'dc->links' 12 <= 12 suggests that the
code is trying to access an element of the dc->links array that is
beyond its bounds. In C, arrays are zero-indexed, so an array with 12
elements has valid indices from 0 to 11. Trying to access dc->links[12]
would be an attempt to access the 13th element of a 12-element array,
which is a buffer overflow.
To fix this, ensure that the loop does not go beyond the last valid
index when accessing dc->links[i + 1] by subtracting 1 from the loop
condition.
This would ensure that i + 1 is always a valid index in the array.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/link/protocols/link_dp_dpia_bw.c:208 get_host_router_total_dp_tunnel_bw() error: buffer overflow 'dc->links' 12 <= 12
Fixes: 59f1622a5f ("drm/amd/display: Add dpia display mode validation logic")
Cc: PeiChen Huang <peichen.huang@amd.com>
Cc: Aric Cyr <aric.cyr@amd.com>
Cc: Rodrigo Siqueira <rodrigo.siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There exists scenarios where the split index for subvp can be
pipe index 0. The assumption in FW is that the split index
won't be 0 but this is incorrect.
[how]
Instead populate non-split cases to be 0xF to differentiate
between split and non-split.
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On 14us for exit latency time causes underflow for 8K monitor with HDR on.
Increasing the latency to 28us fixes the underflow.
[How]
Increase the latency to 28us. This workaround should be sufficient
before we figure out why SR exit so long.
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Nicholas Susanto <nicholas.susanto@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In current code, we recognize a pipe as a phantom pipe if it references
the same phantom stream. However it can also a phantom split pipe.
If the phantom split pipe has a smaller pipe index than the phantom pipe
we will mistakenly use the phantom split pipe as the phantom pipe. This
causes an incorrect subvp configuration where the first half of the
screen is flashing solid white image.
[how]
Add additional check that the pipe needs to be an OTG master pipe.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
1. To watch dmcub inbox1 ring buffer cmd type without tools
2. dmub_cmd_PLAT_54186_wa 66 bytes
[How]
Added dmcub cmd type enum: unsigned char for debug use only,
also fixed 66 bytes issue by using unsigned int in bit
define instead of unsigned char.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Fudongwang <fudong.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previous patch to allow DTBCLK disable didn't address boot case. Driver
thinks DTBCLK is disabled by default, so we don't send disable message to
PMFW. DTBCLK is then enabled at idle desktop on boot, burning power.
[How]
Set dtbclk_en to true on boot so that disable message is sent during first
commit.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Taimur Hassan <syed.hassan@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
fix reading edp rx crc timeout failure. after
bootup, kernel setup psr with dpcd 0x170 = 5. this
notify rx psr enable and let rx fw start checking crc
for fw internal logic. rx fw may not update crc read
count within dpcd 0x246. read count is always 0. this
will lead tx crc reading timeout.
[How]
add debugfs to let test app to disbable rx crc
checking for rx internal logic. then test app can read
rx crc dpcd 0x246 successfully.
expected app sequence is as below:
1. disable eDP PHY and notify eDP rx with dpcd 0x600 = 2.
2. echo 0x1 /sys/kernel/debug/dri/0/eDP-X/disallow_edp_enter_psr
3. enable eDP PHY and notify eDP rx with dpcd 0x600 = 1 but
without dpcd 0x170 = 5.
4. read crc from rx dpcd 0x270, 0x246, etc.
5. echo 0x0 /sys/kernel/debug/dri/0/eDP-X/disallow_edp_enter_psr.
this will let eDP back to normal with psr setup dpcd 0x170 = 5.
Reviewed-by: Wayne Lin <wayne.lin@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
For FPO and SubVP/DRR cases we need to ensure to program
OTG_V_TOTAL_MIN/MAX_SEL, otherwise stretching the vblank
in FPO / SubVP / DRR cases will not have any effect
and we could hit underflow / corruption.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There is only a single call to dc_post_update_surfaces_to_stream
so there is no need to have two flags to control it. Unifying
this to a single flag allows dc_stream_adjust_vmin_vmax to skip
actual programming when there is no change required.
[how]
Remove wm_optimze_required flag and set only optimize_required in its
place. Then in dc_stream_adjust_vmin_vmax, check that the stream timing
range matches the requested one and skip programming if they are equal.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Originally, PMFW said min FCLK is 300Mhz, but min DCFCLK can be increased
to 400Mhz because min FCLK is now 600Mhz so FCLK >= 1.5 * DCFCLK hardware
requirement will still be satisfied. Increasing min DCFCLK addresses
underflow issues (underflow occurs when phantom pipe is turned on for some
Sub-Viewport configs).
[how]
Increasing DCFCLK by raising the min_dcfclk_mhz
Reviewed-by: Chaitanya Dhere <chaitanya.dhere@amd.com>
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Sohaib Nadeem <sohaib.nadeem@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We want acknowledgment of the driver idle disallow from DMCUB before
continuing with any further programming.
For idle allow we want to minimize the chance of DMCUB actively
interacing with other firmware components on the system (eg. PMFW)
at the same time.
[How]
Ensure that DMCUB isn't in the middle of processing other command
submissions prior to allowing idle and after disallowing idle by
inserting a wait before the allow and by changing the wait type for
the idle disallow.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The 'stream' pointer is used in dcn10_set_output_transfer_func() before
the check if 'stream' is NULL.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/../display/dc/hwss/dcn10/dcn10_hwseq.c:1892 dcn10_set_output_transfer_func() warn: variable dereferenced before check 'stream' (see line 1875)
Fixes: ddef02de0d ("drm/amd/display: add null checks before logging")
Cc: Wyatt Wood <wyatt.wood@amd.com>
Cc: Anthony Koo <Anthony.Koo@amd.com>
Cc: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
IPS was temporary disabled due to instability.
It was fixed in dmub firmware and with:
- "drm/amd/display: Add IPS checks before dcn register access"
- "drm/amd/display: Disable ips before dc interrupt setting"
[How]
Enable IPS by default.
Disable IPS if 0x800 bit set in amdgpu.dcdebugmask module params
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
While in IPS2 an access to dcn registers is not allowed.
If interrupt results in dc call, we should disable IPS.
[How]
Safeguard register access in IPS2 by disabling idle optimization
before calling dc interrupt setting api.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Tested-by: Mark Broadworth <mark.broadworth@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
