If the drm/msm init code gets an error during output modeset
initialisation, the kernel will report an error regarding DRM memory
manager not being clean during shutdown. This is because
msm_dsi_modeset_init() allocates a piece of GEM memory for the TX
buffer, but destruction of the buffer happens only at
msm_dsi_host_destroy(), which is called during DSI driver's remove()
time, much later than the DRM MM shutdown.
To solve this issue, move the TX buffer destruction to dsi_unbind(), so
that the buffer is destructed at the correct time. Note, we also have to
store a reference to the address space, because priv->kms->aspace is
cleared before components are unbound.
Reported-by: Bjorn Andersson <andersson@kernel.org>
Fixes: 8f59ee9a57 ("drm/msm/dsi: Adjust probe order")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/562238/
Signed-off-by: Rob Clark <robdclark@chromium.org>
dsi_wait4video_done() API waits for the DSI video mode engine to
become idle so that we can transmit the DCS commands in the
beginning of BLLP. However, with the current sequence, the MDP
timing engine is turned on after the panel's pre_enable() callback
which can send out the DCS commands needed to power up the panel.
During those cases, this API will always timeout and print out the
error spam leading to long bootup times and log flooding.
Fix this by checking if the DSI video engine was actually busy before
waiting for it to become idle otherwise this is a redundant wait.
changes in v2:
- move the reg read below the video mode check
- minor fixes in commit text
Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/34
Fixes: a689554ba6 ("drm/msm: Initial add DSI connector support")
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/557853/
Link: https://lore.kernel.org/r/20230915204426.19011-1-quic_abhinavk@quicinc.com
Updates for v6.6, which includes a backmerge of msm-fixes to avoid conficts.
Core:
- SM6125 MDSS support
DPU:
- SM6125 DPU support
- Added subblocks to display snapshot
- Use UBWC data from MDSS driver rather than duplicating it
- dpu_core_perf cleanup
DSI:
- Enabled burst mode to fix CMD mode panels
- Runtime PM support
- refgen regulator support
DSI PHY:
- SM6125 support in 14nm DSI PHY driver
GPU:
- Rework GPU identification to prepare for a7xx, and other a7xx prep
- Cleanups and fixes
- Disallow legacy relocs on a6xx and newer
- a690: switch to using a660_gmu.bin fw as this is what we have in
linux-firmware and we see no evidence that it should be different
from other a660 family (a6xx subgen 4) devices
- Submit overhead opts, 1.6x faster for NO_IMPLICIT_SYNC commits with
100 BOs to 2.5x faster for 1000 BOs
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGv_01g-edjdfKLWWcb-rO5aSyLsv5FpbKrTkXVL9+ngTQ@mail.gmail.com
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Steven Price <steven.price@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230714174545.4056287-1-robh@kernel.org
Currently, slice_count is being used to calculate word count and
pkt_per_line. Instead, these values should be calculated using slice per
packet, which is not the same as slice_count.
Slice count represents the number of slices per interface, and its value
will not always match that of slice per packet. For example, it is possible
to have cases where there are multiple slices per interface but the panel
specifies only one slice per packet.
Thus, use the default value of one slice per packet and remove slice_count
from the aforementioned calculations.
Fixes: 08802f515c ("drm/msm/dsi: Add support for DSC configuration")
Fixes: bc6b6ff813 ("drm/msm/dsi: Use DSC slice(s) packet size to compute word count")
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/541965/
Link: https://lore.kernel.org/r/20230405-add-dsc-support-v6-5-95eab864d1b6@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Currently, we allow for MAX_DSI entries in io_start to facilitate for
MAX_DSI number of DSI hosts at different addresses. The configuration
is matched against the DSI CTRL hardware revision read back from the
component. We need a way to resolve situations where multiple SoCs
with different register maps may use the same version of DSI CTRL. In
preparation to do so, make msm_dsi_config a 2d array where each entry
represents a set of configurations adequate for a given SoC.
This is totally fine to do, as the only differentiating factors
between same-version-different-SoCs configurations are the number of
DSI hosts (1 or 2, at least as of today) and the set of base registers.
The regulator setup is the same, because the DSI hardware is the same,
regardless of the SoC it was implemented in.
In addition to that, update the matching logic such that it will loop
over VARIANTS_MAX variants, making sure they are all taken into account.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/527652/
Link: https://lore.kernel.org/r/20230307-topic-dsi_qcm-v6-3-70e13b1214fa@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
DPU, DSI, MDSS:
- Support for SM8350, SM8450 SM8550 and SC8280XP platform
Core:
- Added bindings for SM8150 (driver support already present)
DPU:
- Partial support for DSC on SM8150 and SM8250
- Fixed color transformation matrix being lost on suspend/resume
DP:
- Support for DP on SDM845 and SC8280XP platforms
- HPD fixes
- Support for limiting DP link rate via DT property, this enables
support for HBR3 rates.
DSI:
- Validate display modes according to the DSI OPP table
- DSI PHY support for the SM6375 platform
- Fixed byte intf clock selection for 14nm PHYs
MDP5:
- Schema conversion to YAML
Misc fixes as usual
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
According to downstream the value to use for WORD_COUNT is
bytes_per_pkt, which denotes the number of bytes in a packet based on
how many slices have been configured by the panel driver times the
width of a slice times the number of bytes per pixel.
The DSC panels seen thus far use one byte per pixel, only one slice
per packet, and a slice width of half the panel width leading to the
desired bytes_per_pkt+1 value to be equal to hdisplay/2+1. This however
isn't the case anymore for panels that configure two slices per packet,
where the value should now be hdisplay+1.
Note that the aforementioned panel (on a Sony Xperia XZ3, sdm845) with
slice_count=1 has also been tested to successfully accept slice_count=2,
which would have shown corrupted output previously.
Fixes: 08802f515c ("drm/msm/dsi: Add support for DSC configuration")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/515694/
Link: https://lore.kernel.org/r/20221221231943.1961117-3-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
drm_dsc_config's bits_per_pixel field holds a fractional value with 4
bits, which all panel drivers should adhere to for
drm_dsc_pps_payload_pack() to generate a valid payload. All code in the
DSI driver here seems to assume that this field doesn't contain any
fractional bits, hence resulting in the wrong values being computed.
Since none of the calculations leave any room for fractional bits or
seem to indicate any possible area of support, disallow such values
altogether. calculate_rc_params() in intel_vdsc.c performs an identical
bitshift to get at this integer value.
Fixes: b9080324d6 ("drm/msm/dsi: add support for dsc data")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/508938/
Link: https://lore.kernel.org/r/20221026182824.876933-8-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
As per the FIXME this code is entirely duplicate with what is already
provided inside drm_dsc_compute_rc_parameters(), supposedly because that
function was yielding "incorrect" results while in reality the panel
driver(s?) used for testing were providing incorrect parameters.
For example, this code from downstream assumed dsc->bits_per_pixel to
contain an integer value, whereas the upstream drm_dsc_config struct
stores it with 4 fractional bits. drm_dsc_compute_rc_parameters()
already accounts for this feat while the panel driver used for testing
[1] wasn't, hence making drm_dsc_compute_rc_parameters() seem like it
was returning an incorrect result.
Other users of dsc->bits_per_pixel inside dsi_populate_dsc_params() also
treat it in the same erroneous way, and will be addressed in a separate
patch.
In the end, using drm_dsc_compute_rc_parameters() spares both a lot of
duplicate code and erratic behaviour.
[1]: https://git.linaro.org/people/vinod.koul/kernel.git/commit/?h=topic/pixel3_5.18-rc1&id=1d7d98ad564f1ec69e7525e07418918d90f247a1
Fixes: b9080324d6 ("drm/msm/dsi: add support for dsc data")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/508939/
Link: https://lore.kernel.org/r/20221026182824.876933-7-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
This field is currently unread but will come into effect when duplicated
code below is migrated to call drm_dsc_compute_rc_parameters(), which
uses the bpc-dependent value of the local variable mux_words_size in
much the same way.
The hardcoded constant seems to be a remnant from the `/* bpc 8 */`
comment right above, indicating that this group of field assignments is
applicable to bpc = 8 exclusively and should probably bail out on
different bpc values, until constants for other bpc values are added (or
the current ones are confirmed to be correct across multiple bpc's).
Fixes: b9080324d6 ("drm/msm/dsi: add support for dsc data")
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/508943/
Link: https://lore.kernel.org/r/20221026182824.876933-6-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
As of the commit 1de452a0ed ("regulator: core: Allow drivers to
define their init data as const") we no longer need to do copying of
regulator bulk data from initdata to something dynamic. Let's take
advantage of that.
In addition to saving some code, this also moves us to using
ARRAY_SIZE() to specify how many regulators we have which is less
error prone.
This gets rid of some layers of wrappers which makes it obvious that
we can get rid of an extra error print.
devm_regulator_bulk_get_const() prints errors for you so you don't
need an extra layer of printing.
In all cases here I have preserved the old settings without any
investigation about whether the loads being set are sensible. In the
cases of some of the PHYs if several PHYs in the same file used
exactly the same settings I had them point to the same data structure.
NOTE: Though I haven't done the math, this is likely an overall
savings in terms of "static const" data. We previously always
allocated space for 8 supplies. Each of these supplies took up 36
bytes of data (32 for name, 4 for an int).
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/496325/
Link: https://lore.kernel.org/r/20220804073608.v4.5.I55a9e65cb1c22221316629e98768ff473f47a067@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
As of commit 5451781dad ("regulator: core: Only count load for
enabled consumers"), a load isn't counted for a disabled
regulator. That means all the code in the DSI driver to specify and
set loads before disabling a regulator is not actually doing anything
useful. Let's remove it.
It should be noted that all of the loads set that were being specified
were pointless noise anyway. The only use for this number is to pick
between low power and high power modes of regulators. Regulators
appear to do this changeover at loads on the order of 10000 uA. You
would need a lot of clients of the same rail for that 100 uA number to
count for anything.
Note that now that we get rid of the setting of the load at disable
time, we can just set the load once when we first get the regulator
and then forget it.
It should also be noted that the regulator functions
regulator_bulk_enable() and regulator_set_load() already print error
messages when they encounter problems so while moving things around we
get rid of some extra error prints.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/496320/
Link: https://lore.kernel.org/r/20220804073608.v4.3.If1f94fbbdb7c1d0fb3961de61483a851ad1971a7@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Next for v5.20
GPU:
- a619 support
- Fix for unclocked GMU register access
- Devcore dump enhancements
Core:
- client utilization via fdinfo support
- fix fence rollover issue
- gem: Lockdep false-positive warning fix
- gem: Switch to pfn mappings
DPU:
- constification of HW catalog
- support for using encoder as CRC source
- WB support on sc7180
- WB resolution fixes
DP:
- dropped custom bulk clock implementation
- made dp_bridge_mode_valid() return MODE_CLOCK_HIGH where applicable
- fix link retraining on resolution change
MDP5:
- MSM8953 perf data
HDMI:
- YAML'ification of schema
- dropped obsolete GPIO support
- misc cleanups
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGtuqswBGPw-kCYzJvckK2RR1XTeUEgaXwVG_mvpbv3gPA@mail.gmail.com
