Currently whenever link AP beacon is assigned, sdata->u.ap.active flag is
set and whenever it is brought down, the flag is reset. However, with MLO,
all the links of the same MLD would use the same sdata. Hence there is no
need to set/reset for each link up/down. Also, resetting it when only one
of the links went down is not desirable.
Add changes to set the active flag only when first link is assigned
beacon. Similarly, add changes to reset that flag only when last link is
brought down.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240409094017.3165560-1-quic_adisi@quicinc.com
[remove unnecessary check before constant true assignment]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's an issue in that when we disconnect from an AP
due to the AP switching to an unsupported channel, we
might not tell the driver about this before we try to
send the deauth. If the underlying implementation has
detected the quiet CSA, this may cause issues if this
is the only active link. Avoid this by transmitting
(and flushing) the deauth only when there's an active
link available that's not affected by quiet CSA.
Since this introduces link->u.mgd.csa_blocked_tx and we
no longer check sdata->csa_blocked_tx for the TX itself
also rename the latter to csa_blocked_queues.
Fixes: 6f0107d195 ("wifi: mac80211: introduce a feature flag for quiet in CSA")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240415112355.1d91db5e95aa.Iad3a5df3367f305dff48cd61776abfd6cf0fd4ab@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When doing CSA in multi-link, there really isn't a need to
stop transmissions entirely. Add a feature flag for drivers
to indicate they can handle quiet in CSA (be it by parsing
themselves, or by implementing drv_pre_channel_switch()),
to make that possible.
Also clean up the csa_block_tx handling: it clearly cannot
handle multi-link due to the way queues are stopped, move
it to the sdata. Drivers should be doing it themselves for
working properly during CSA in MLO anyway. Also rename it
to indicate that it reflects TX was blocked at mac80211.
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228095719.258439191541.I2469d206e2bf5cb244cfde2b4bbc2ae6d1cd3dd9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The CQM handling did not consider the MLO case and thus notified
a not-existing link with the CQM change. To fix this, propagate
the CQM notification to all the active links (handling both the
non-MLO and MLO cases).
TODO: this currently propagates the same configuration to all
links regardless of the band. This might not be the correct
approach as different links might need to be configured with
different values.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228094753.bf6a3fefe553.Id738810b73e1087e01d5885508b70a3631707627@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently whenever link AP is started, netif_carrier_up() function is
called and whenever it is brought down, netif_carrier_down() function is
called. However, with MLO, all the links of the same MLD would use the
same netdev. Hence there is no need to indicate for each link up/down.
Also, calling it down when only one of the links went down is not
desirable.
Add changes to call the netif_carrier_up() function only when first link
is brought up. Similarly, add changes to call the netif_carrier_down()
function only when last link is brought down.
In order to check the number of beaconing links in the given interface,
introduce a new helper function ieee80211_num_beaconing_links().
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240227042251.1511122-3-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We're currently tracking rx_nss for each station, and that
is meant to be initialized to the capability NSS and later
reduced by the operating mode notification NSS.
However, we're mixing up capabilities and operating mode
NSS in the same variable. This forces us to recalculate
the NSS capability on operating mode notification RX,
which is a bit strange; due to the previous fix I had to
never keep rx_nss as zero, it also means that the capa is
never taken into account properly.
Fix all this by storing the capability value, that can be
recalculated unconditionally whenever needed, and storing
the operating mode notification NSS separately, taking it
into account when assigning the final rx_nss value.
Cc: stable@vger.kernel.org
Fixes: dd6c064cfc ("wifi: mac80211: set station RX-NSS on reconfig")
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240228120157.0e1c41924d1d.I0acaa234e0267227b7e3ef81a59117c8792116bc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, whenever AP link is brought down via ieee80211_stop_ap()
function, all stations connected to the sdata are flushed. However, in case
of MLO there is a requirement to flush only stations connected to that link
and not all.
For instance - Consider 2 GHz and 5 GHz are AP MLD. Now due to some reason
5 GHz link of this AP is going down (link removal or any other case). All
stations connected, even legacy stations connected to 2 GHz link AP would
also be flushed. Flushing of other link stations is not desirable.
Fix this issue by passing self link ID to sta_flush() function. This would
then only remove the stations which are still using the passed link
ID as their link sta. Other stations will not be affected.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240205162952.1697646-4-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Whenever sta_flush() function is invoked, all STAs present in that
interface are flushed. In case of MLO, it is desirable to only flush such
STAs that are at least using a given link id as one of their links.
Add support for this by making change in the __sta_info_flush API argument
to accept a link ID. And then, only if the STA is using the given link as
one of its links, it would be flushed.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240205162952.1697646-3-quic_adisi@quicinc.com
[reword commit message, in particular this isn't about "active" links]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In order to support CSA with MLO, there is a need to handle the functions
ieee80211_set_csa_beacon() and ieee80211_set_after_csa_beacon() on a per
link basis.
Implement this by making the function argument accept the the link data
instead of the sdata.
Currently, deflink would only be passed. Proper link data will be passed in
a subsequent patch.
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240130140918.1172387-4-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For channel contexts, mac80211 currently uses the cfg80211
chandef struct (control channel, center freq(s), width) to
define towards drivers and internally how these behave. In
fact, there are _two_ such structs used, where the min_def
can reduce bandwidth according to the stations connected.
Unfortunately, with EHT this is longer be sufficient, at
least not for all hardware. EHT requires that non-AP STAs
that are connected to an AP with a lower bandwidth than it
(the AP) advertises (e.g. 160 MHz STA connected to 320 MHz
AP) still be able to receive downlink OFDMA and respond to
trigger frames for uplink OFDMA that specify the position
and bandwidth for the non-AP STA relative to the channel
the AP is using. Therefore, they need to be aware of this,
and at least for some hardware (e.g. Intel) this awareness
is in the hardware. As a result, use of the "same" channel
may need to be split over two channel contexts where they
differ by the AP being used.
As a first step, introduce a concept of a channel request
('chanreq') for each interface, to control the context it
requests. This step does nothing but reorganise the code,
so that later the AP's chandef can be added to the request
in order to handle the EHT case described above.
Link: https://msgid.link/20240129194108.2e88e48bd2e9.I4256183debe975c5ed71621611206fdbb69ba330@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are still surprisingly many non-chanctx drivers, but in
mac80211 that code is a bit awkward. Simplify this by having
those drivers assign 'emulated' ops, so that the mac80211 code
can be more unified between non-chanctx/chanctx drivers. This
cuts the number of places caring about it by about 15, which
are scattered across - now they're fewer and no longer in the
channel context handling.
Link: https://msgid.link/20240129194108.6d0ead50f5cf.I60d093b2fc81ca1853925a4d0ac3a2337d5baa5b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are some changes coming to wireless-next that will
otherwise cause conflicts, pull wireless in first to be
able to resolve that when applying the individual changes
rather than having to do merge resolution later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Resolve several conflicts, mostly between changes/fixes in
wireless and the locking rework in wireless-next. One of
the conflicts actually shows a bug in wireless that we'll
want to fix separately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Using the full struct cfg80211_ap_settings for an update is
misleading, since most settings cannot be updated. Split the
update case off into a new struct cfg80211_ap_update.
Change-Id: I3ba4dd9280938ab41252f145227a7005edf327e4
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When ieee80211_key_link() is called by ieee80211_gtk_rekey_add()
but returns 0 due to KRACK protection (identical key reinstall),
ieee80211_gtk_rekey_add() will still return a pointer into the
key, in a potential use-after-free. This normally doesn't happen
since it's only called by iwlwifi in case of WoWLAN rekey offload
which has its own KRACK protection, but still better to fix, do
that by returning an error code and converting that to success on
the cfg80211 boundary only, leaving the error for bad callers of
ieee80211_gtk_rekey_add().
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: fdf7cb4185 ("mac80211: accept key reinstall without changing anything")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We can get a UBSAN warning if ieee80211_get_tx_power() returns the
INT_MIN value mac80211 internally uses for "unset power level".
UBSAN: signed-integer-overflow in net/wireless/nl80211.c:3816:5
-2147483648 * 100 cannot be represented in type 'int'
CPU: 0 PID: 20433 Comm: insmod Tainted: G WC OE
Call Trace:
dump_stack+0x74/0x92
ubsan_epilogue+0x9/0x50
handle_overflow+0x8d/0xd0
__ubsan_handle_mul_overflow+0xe/0x10
nl80211_send_iface+0x688/0x6b0 [cfg80211]
[...]
cfg80211_register_wdev+0x78/0xb0 [cfg80211]
cfg80211_netdev_notifier_call+0x200/0x620 [cfg80211]
[...]
ieee80211_if_add+0x60e/0x8f0 [mac80211]
ieee80211_register_hw+0xda5/0x1170 [mac80211]
In this case, simply return an error instead, to indicate
that no data is available.
Cc: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://lore.kernel.org/r/20230203023636.4418-1-pkshih@realtek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Modify the prototype for change_beacon() in struct cfg80211_op to
accept cfg80211_ap_settings instead of cfg80211_beacon_data so that
it can process data in addition to beacons.
Modify the prototypes of ieee80211_change_beacon() and driver specific
functions accordingly.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20230727174100.11721-4-quic_alokad@quicinc.com
[while at it, remove pointless "if (info)" check in tracing that just
makes all the lines longer than they need be - it's never NULL]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
FILS discovery configuration gets updated only if the maximum interval
is set to a non-zero value, hence there is no way to reset this value
to 0 once set. Replace the check for interval with a new flag which is
set only if the configuration should be updated.
Add similar changes for the unsolicited broadcast probe response handling.
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Link: https://lore.kernel.org/r/20230727174100.11721-3-quic_alokad@quicinc.com
[move NULL'ing to else branch to not have intermediate NULL visible]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We really cannot even get into this as we can't have
a BSS with a 5/10 MHz (scan) width, and therefore all
the code handling shifted rates cannot happen. Remove
it all, since it's broken anyway, at least with MLO.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since we're now protecting everything with the wiphy mutex
(and were really using it for almost everything before),
there's no longer any real reason to have a separate wdev
mutex. It may feel better, but really has no value.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We now hold the wiphy mutex everywhere that we use or
needed the iflist_mtx, so we don't need this mutex any
more in mac80211. However, drivers may also iterate,
and in some cases (e.g. mt76) do so from high-priority
contexts. Thus, keep the mutex around but remove its
usage in mac80211 apart from those driver-visible parts
that are still needed.
Most of this change was done automatically with spatch,
with the parts that are still needed as described above
reverted manually.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We now hold the wiphy mutex everywhere that we use or
needed the local->mtx, so we don't need this mutex any
more. Remove it.
Most of this change was done automatically with spatch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
