[ Upstream commit a51d9f8fe7 ]
[Why]
In dc_link_is_dp_sink_present, if dal_ddc_open fails, then
dal_gpio_destroy_ddc is called, destroying pin_data and pin_clock. They
are created only on dc_construct, and next aux access will cause a panic.
[How]
Instead of calling dal_gpio_destroy_ddc, call dal_ddc_close.
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd998291db ]
[WHY]
During detection:
function: get_active_converter_info populates link->dpcd_caps.dongle_caps
only when dpcd_rev >= DPCD_REV_11 and DWN_STRM_PORTX_TYPE is
DOWN_STREAM_DETAILED_HDMI or DOWN_STREAM_DETAILED_DP_PLUS_PLUS.
Otherwise, it is not cleared, and stale information remains.
During mode validation:
function: dp_active_dongle_validate_timing reads
link->dpcd_caps.dongle_caps->dongle_type to determine the maximum
pixel clock to support. This information is now stale and no longer
valid.
[HOW]
dp_active_dongle_validate_timing should be using
link->dpcd_caps->dongle_type instead.
Signed-off-by: David Galiffi <david.galiffi@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc2fde42e2 ]
[WHY]
i2c_read is called to differentiate passive DP->HDMI and DP->DVI-D dongles
The call is expected to fail in DVI-D case but pass in HDMI case
Some HDMI dongles have a chance to fail as well, causing misdetection as DVI-D
[HOW]
Retry i2c_read to ensure failed result is valid
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e5382701c3 ]
[Why]
The vm config will be clear to 0 when system enter S4. It will
cause hubbub didn't know how to fetch data when system resume.
The flip always pending because earliest_inuse_address and
request_address are different.
[How]
Reprogram VM config when system resume
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1cbcfc9751 ]
[Why]
When endpoint is at the boundary of a region, such as at 2^0=1
we find that the last segment has a sharp slope and some points
are clipped at the top.
[How]
If end point is 1, which is exactly at the 2^0 region boundary, we
need to program an additional region beyond this point.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit bb264220d9 upstream.
Laptops with AMD APU doesn't restore display backlight brightness after
system resume.
This issue started when DC was introduced.
Let's use BL_CORE_SUSPENDRESUME so the backlight core calls
update_status callback after system resume to restore the backlight
level.
Tested on Dell Inspiron 3180 (Stoney Ridge) and Dell Latitude 5495
(Raven Ridge).
Cc: <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0f0727d971 ]
arch/x86/Makefile disables SSE and SSE2 for the whole kernel. The
AMDGPU drivers modified in this patch re-enable SSE but not SSE2. Turn
on SSE2 to support emitting double precision floating point instructions
rather than calls to non-existent (usually available from gcc_s or
compiler_rt) floating point helper routines for Clang.
This was originally landed in:
commit 1011745073 ("drm/amd/display: add -msse2 to prevent Clang from emitting libcalls to undefined SW FP routines")
but reverted in:
commit 193392ed9f ("Revert "drm/amd/display: add -msse2 to prevent Clang from emitting libcalls to undefined SW FP routines"")
due to bugreports from GCC builds. Add guards to only do so for Clang.
Link: https://bugs.freedesktop.org/show_bug.cgi?id=109487
Link: https://github.com/ClangBuiltLinux/linux/issues/327
Suggested-by: Sedat Dilek <sedat.dilek@gmail.com>
Suggested-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04ac4b0ed4 ]
Path property is used for userspace to know what MST connector goes to what actual DRM DisplayPort connector, the tiling property is for tiling configurations. Not sure what else there is to figure out.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7352193a33 ]
[Why]
The audios array defined in "struct resource_pool" is only 6 (MAX_PIPES)
but the max number of audio devices (num_audio) is 7. In some projects,
it will run out of audios array.
[How]
Incraese the audios array size to 7.
Signed-off-by: Tai Man <taiman.wong@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ac25e6d5b ]
[Why]
In dm_helpers_parse_edid_caps, there is a corner case where no speakers
can be allocated even though the audio mode count is greater than 0.
Enabling audio when no speaker allocations exists can cause issues in
the video stream.
[How]
Add a check to not enable audio unless one or more speaker allocations
exist (since doing this can cause issues in the video stream).
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0905f32977 ]
[Why]
It is possible (but very unlikely) that constructing dc fails
before current_state is created.
We support 666 color depth in some scenarios, but this
isn't handled in get_norm_pix_clk. It uses exactly the
same pixel clock as the 888 case.
[How]
Check for non null current_state before destructing.
Add case for 666 color depth to get_norm_pix_clk to
avoid assertion.
Signed-off-by: Julian Parkin <julian.parkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74eda776d7 ]
[Why]
On some platforms, the encoder id 3 is not populated. So the encoders
are not stored in right order as index (id: 0, 1, 2, 4, 5) at pool. This
would cause encoders id 4 & id 5 to fail when finding corresponding
audio device, defaulting to the first available audio device. As result,
we cannot stream audio into two DP ports with encoders id 4 & id 5.
[How]
It need to create enough audio device objects (0 - 5) to perform matching.
Then use encoder engine id to find matched audio device.
Signed-off-by: Tai Man <taiman.wong@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7990daebe ]
[WHY]
Currently we don't wait for blacklight programming completion in DMCU
when setting backlight level. Some sequences such as PSR static screen
event trigger reprogramming requires it to be complete.
[How]
Add generic wait for dmcu command completion in set backlight level.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f04bee34d6 ]
[Why]
Unlike our regular connectors, MST connectors don't start off with
an initial connector state. This causes a NULL pointer dereference to
occur when attaching the bpc property since it tries to modify the
connector state.
We need an initial connector state on the connector to avoid the crash.
[How]
Use our reset helper to allocate an initial state and reset the values
to their defaults. We were already doing this before, just not for
MST connectors.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1090d58d48 ]
[Why]
When disable driver, OS will set backlight optimization
then do stop device. But this flag will cause driver to
enable ABM when driver disabled.
[How]
Send ABM disable command before destroy ABM construct
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1352c779cb ]
[Why]
An assertion is thrown when using SURFACE_PIXEL_FORMAT_GRPH_RGB565
formats on DCE since the prescale_params->scale wasn't being filled.
Found by a dmesg-fail when running the
igt@kms_plane@pixel-format-pipe-a-planes test on Baffin.
[How]
Fill in the scale parameter.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a1e07ba89d ]
[Why]
The input color space for the plane was previously ignored even if it
was set.
If a limited range YUV format was given to DC then the
wrong color transformation matrix was being used since DC assumed that
it was full range instead.
[How]
Respect the given color_space format for the plane if it isn't
COLOR_SPACE_UNKNOWN. Otherwise, use the implicit default since DM
didn't specify.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9952f93cd ]
[Why]
The kms_plane@plane-position-covered-pipe-*-planes subtests can produce
a sequence of atomic commits such that neither active_changed nor
mode_changed but connectors_changed.
When this happens we remove the old stream from the context and add
a new stream but the new stream doesn't have mode_changed=true set.
This incorrect programming sequence causes CRC mismatches to occur in
the test.
The stream->mode_changed value should be set whenever a new stream
is created.
[How]
A new stream is created whenever drm_atomic_crtc_needs_modeset is true.
We previously covered the active_changed and mode_changed conditions
for the CRTC but connectors_changed is also checked within
drm_atomic_crtc_needs_modeset.
So just use drm_atomic_crtc_needs_modeset directly to determine the
mode_changed flag.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c238bfe0be ]
[Why]
On some compositors, with two monitors attached, VT terminal
switch can cause a graphical issue by the following means:
There are two streams, one for each monitor. Each stream has one
plane
current state:
M1:S1->P1
M2:S2->P2
The user calls for a terminal switch and a commit is made to
change both planes to linear swizzle mode. In atomic check,
a new dc_state is constructed with new planes on each stream
new state:
M1:S1->P3
M2:S2->P4
In commit tail, each stream is committed, one at a time. The first
stream (S1) updates properly, triggerring a full update and replacing
the state
current state:
M1:S1->P3
M2:S2->P4
The update for S2 comes in, but dc detects that there is no difference
between the stream and plane in the new and current states, and so
triggers a fast update. The fast update does not program swizzle,
so the second monitor is corrupted
[How]
Add a flag to dc_plane_state that forces full updates
When a stream undergoes a full update, set this flag on all changed
planes, then clear it on the current stream
Subsequent streams will get full updates as a result
Signed-off-by: David Francis <David.Francis@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet Lakha@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f4bbebf8e7 ]
[Why]
AUX takes longer to reply when using active DP-DVI dongle on some asics
resulting in up to 2000+ us edid read (timeout).
[How]
1. Adjust AUX poll to match spec
2. Extend the SW timeout. This does not affect normal
operation since we exit the loop as soon as AUX acks.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c1cefe115d ]
[Why]
the member sdr_white_level of struct dc_cursor_attributes was not
initialized, then the random value result that
dcn10_set_cursor_sdr_white_level() set error hw_scale value 0x20D9(normal
value is 0x3c00), this cause the black cursor issue.
[how]
just initilize the obj of struct dc_cursor_attributes to zero to avoid
the random value.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Tianci Yin <tianci.yin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 428da2bdb0 ]
[Why]
In order to read CRC events when CRC capture is enabled the vblank
interrput handler needs to be running for the CRTC. The handler is
enabled while there is an active vblank reference.
When running IGT tests there will often be no active vblank reference
but the test expects to read a CRC value. This is valid usage (and
works on i915 since they have a CRC interrupt handler) so the reference
to the vblank should be grabbed while capture is active.
This issue was found running:
igt@kms_plane_multiple@atomic-pipe-b-tiling-none
The pipe-b is the only one in the initial commit and was not previously
active so no vblank reference is grabbed. The vblank interrupt is
not enabled and the test times out.
[How]
Keep a reference to the vblank as long as CRC capture is enabled.
If userspace never explicitly disables it then the reference is
also dropped when removing the CRTC from the context (stream = NULL).
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 77476360f1 ]
[Why]
This fixes an mpc programming error for the following sequence of
atomic commits when pipe split is enabled:
Commit 1: CRTC0 (plane 4, plane 3)
Pipe 0: old_plane_state = A0, new_plane_state = A1, new_tg = T0
Pipe 1: old_plane_state = B0, new_plane_state = B1, new_tg = T0
Pipe 2: old_plane_state = A0, new_plane_state = A1, new_tg = T0
Pipe 3: old_plane_state = B0, new_plane_state = B1, new_tg = T0
Commit 2: CRTC0 (plane 3), CRTC1 (plane 2)
Pipe 0: old_plane_state = A1, new_plane_state = A2, new_tg = T0
Pipe 1: old_plane_state = B1, new_plane_state = B2, new_tg = T1
Pipe 2: old_plane_state = A1, new_plane_state = NULL, new_tg = NULL
Pipe 3: old_plane_state = B1, new_plane_state = NULL, new_tg = NULL
In the second commit the assertion for mpcc in use is hit because
mpcc disconnect never occurs for pipe 1. This is because the stream
changes for pipe 1 and the opp_list is empty.
This sequence occurs when running the
"igt@kms_plane_multiple@atomic-pipe-A-tiling-none" test with two
displays connected.
[How]
Expand the reset condition to include:
"old_pipe_ctx->stream_res.tg != new_pipe_ctx->stream_res.tg"
...but only when the plane state is non-NULL for both old and new.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5062b797db ]
[Why]
There are opt1c lock warnings and CRTC read timeouts when running the
"igt@kms_plane@plane-position-hole-dpms-pipe-*" tests. These are
caused by trying to reprogram planes that are not in the current
context.
DPMS off removes the stream from the context. In this case:
new_crtc_state->active_changed = true
new_crtc_state->mode_changed = false
The planes are reprogrammed before the stream is removed from the
context because stream_state->mode_changed = false.
For DPMS adds the stream and planes back to the context:
new_crtc_state->active_changed = true
new_crtc_state->mode_changed = false
The planes are also reprogrammed here before the stream is added to the
context because stream_state->mode_changed = true. They were not
previously in the current context so warnings occur here.
[How]
Set stream_state->mode_changed = true when
new_crtc_state->active_changed = true too.
This prevents reprogramming before the context is applied in DC. The
programming will be done after the context is applied.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8d2f174bc ]
[Why]
The stream->mode_changed flag can persist in the following sequence
of atomic commits:
Commit 1:
Enable CRTC0 (mode_changed = true), Enable CRTC1 (mode_changed = true)
Commit 2:
Disable CRTC1 (mode_changed = false)
In this sequence we want to keep the exiting CRTC0 but it's not in the
atomic state for the commit since it hasn't been modified. In this case
the stream->mode_changed flag persists as true and we don't re-program
the planes for the existing stream.
[How]
The flag needs to be cleared and it makes the most sense to do it within
DC after the state has been committed. Nothing following dc_commit_state
should think that the stream's mode has changed.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 59d3191f14 upstream.
Powerplay functions called from dm_pp_* functions tend to do a
mutex_lock which isn't safe to do inside a kernel_fpu_begin/end block as
those will disable/enable preemption.
Rearrange the dm_pp_get_clock_levels_by_type_with_voltage calls to make
sure they happen outside of kernel_fpu_begin/end.
Cc: stable@vger.kernel.org
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d2f0b53bda upstream.
[Why]
drm_dp_mst_topology_mgr_suspend() is added into the new reboot
sequence, which disables the UP request at the beginning.
Therefore sideband messages are blocked.
[How]
Finish MST sideband message transaction before UP request is
suppressed.
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 99b922f9ed ]
[why]
Some dongle doesn't have a valid extended dongle caps,
but we still set the extended dongle caps to be valid.
This causes validation fails for all timing.
[how]
If no dp_hdmi_max_pixel_clk is provided,
don't use extended dongle caps.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Abdoulaye Berthe <Abdoulaye.Berthe@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 12750d1647 ]
[Why]
YCbCr420 packing format uses two chanels for luma, and 1
channel for both chroma component. Our previous implementation
did not account for this and results in every other pixel having
very high luma value, showing greyish color instead of black.
YCbCr444 = <Y1, Cb1, Cr1>; <Y2, Cb2, Cr2> .....
YCbCr420 = <Y1, Y2, Cb1>; <Y3, Y4, Cr1> .....
[How]
Program the second channel with the black color value for luma
as well.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Hugo Hu <Hugo.Hu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bd4905a958 ]
[WHY]
On customer board, there is one pluse (1v , < 1ms) on
DDC_CLK pin when plug / unplug DP cable. Driver will read
it and config DP to HDMI/DVI dongle.
[HOW]
If there is a real dongle, DDC_CLK should be always pull high.
Try to read again to recovery this special case. Retry times = 3.
Need additional 3ms to detect DP passive dongle(3 failures)
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08e1c28dd5 ]
[why]
phy_pix_clk is one of the variable used to check if one PLL can be shared
with displays having common mode set configuration. As of now
phy_pix_clock varialbe is calculated in function dc_validate_stream().
dc_validate_stream() function is called after clocks are assigned for the
new display. Due to this during hotplug, when PLL sharing conditions are
checked for new display phy_pix_clk variable will be 0 and for displays
that are already enabled phy_pix_clk will have some value. Hence PLL will
not be shared and if the display hardware doesn't have any more PLL to
assign, mode set will fail due to resource unavailability.
[how]
Instead of only calculating the phy_pix_clk variable after the PLL is
assigned for new display, this patch calculates phy_pix_clk also during
the before assigning the PLL for new display.
Signed-off-by: Yogesh Mohan Marimuthu <yogesh.mohanmarimuthu@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8ce504b938 ]
[why]
Gamma was always being set as identity on SDR monitor,
leading to no changes in gamma. This caused nightlight to
not apply correctly.
[how]
Added a default gamma structure to compare against
in the sdr case.
Signed-off-by: Murton Liu <murton.liu@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f41a895026 ]
[Why]
The igt@kms_plane@pixel-format-pipe tests can create a sequence where
stream_state is NULL during amdgpu_dm_crtc_set_crc_source which results
in a null pointer dereference.
[How]
Guard against stream_state being NULL before accessing its fields. This
doesn't fix the root cause of the issue so a DRM_ERROR is generated
to still fail the tests.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2d1af6a11c upstream.
This is an ugly one unfortunately. Currently, all DRM drivers supporting
atomic modesetting will save the state that userspace had set before
suspending, then attempt to restore that state on resume. This probably
worked very well at one point, like many other things, until DP MST came
into the picture. While it's easy to restore state on normal display
connectors that were disconnected during suspend regardless of their
state post-resume, this can't really be done with MST because of the
fact that setting up a downstream sink requires performing sideband
transactions between the source and the MST hub, sending out the ACT
packets, etc.
Because of this, there isn't really a guarantee that we can restore the
atomic state we had before suspend once we've resumed. This sucks pretty
bad, but so far I haven't run into any compositors that this actually
causes serious issues with. Most compositors will notice the hotplug we
send afterwards, and then reprobe state.
Since nouveau and i915 also don't fail the suspend/resume process due to
failing to restore the atomic state, let's make amdgpu match this
behavior. Better to resume the GPU properly, then to stop the process
half way because of a potentially unavoidable atomic commit failure.
Eventually, we'll have a real fix for this problem on the DRM level. But
we've got some more important low-hanging fruit to deal with first.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Cc: Jerry Zuo <Jerry.Zuo@amd.com>
Cc: <stable@vger.kernel.org> # v4.15+
Link: https://patchwork.freedesktop.org/patch/msgid/20190108211133.32564-3-lyude@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fe7553bef8 upstream.
drm_dp_mst_topology_mgr_resume() returns whether or not it managed to
find the topology in question after a suspend resume cycle, and the
driver is supposed to check this value and disable MST accordingly if
it's gone-in addition to sending a hotplug in order to notify userspace
that something changed during suspend.
Currently, amdgpu just makes the mistake of ignoring the return code
from drm_dp_mst_topology_mgr_resume() which means that if a topology was
removed in suspend, amdgpu never notices and assumes it's still
connected which leads to all sorts of problems.
So, fix this by actually checking the rc from
drm_dp_mst_topology_mgr_resume(). Also, reformat the rest of the
function while we're at it to fix the over-indenting.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Cc: Jerry Zuo <Jerry.Zuo@amd.com>
Cc: <stable@vger.kernel.org> # v4.15+
Link: https://patchwork.freedesktop.org/patch/msgid/20190108211133.32564-2-lyude@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 49f1c44b58 upstream.
[Why]
If the "max bpc" isn't explicitly set in the atomic state then it
have a value of 0. This has the correct behavior of limiting a panel
to 8bpc in the case where the panel supports 8bpc. In the case of eDP
panels this isn't a true assumption - there are panels that can only
do 6bpc.
Banding occurs for these displays.
[How]
Initialize the max_bpc when the connector resets to 8bpc. Also carry
over the value when the state is duplicated.
Bugzilla: https://bugs.freedesktop.org/108825
Fixes: 307638884f72 ("drm/amd/display: Support amdgpu "max bpc" connector property")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 07e3a1cfb0 ]
[Why]
Many panels support more than 8bpc but some modes are unavailable while
running at greater than 8bpc due to DP/HDMI bandwidth constraints.
Support for more than 8bpc was added recently in the driver but it
defaults to the maximum supported bpc - locking out these modes.
This should be a user configurable option such that the user can select
what bpc configuration they would like.
[How]
This patch adds support for getting and setting the amdgpu driver
specific "max bpc" property on the connector.
It also adds support for limiting the output bpc based on the property
value. The default limitation is the lowest value in the range, 8bpc.
This was the old value before the range was uncapped.
This patch should be updated/replaced later once common drm support
for max bpc lands.
Bugzilla: https://bugs.freedesktop.org/108542
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201585
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=200645
Fixes: e03fd3f300 ("drm/amd/display: Do not limit color depth to 8bpc")
v2: rebase on upstream (Alex)
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c9e0ab86b2 upstream.
The change fixed huge delay in SST daisy chain and S3 soft hang
observed in 4.19 kernel rebase.
Regression point in drm:
drm/fb-helper: Eliminate the .best_encoder() usage
The aux sequence is altered due to the failure in
drm_connector_for_each_possible_encoder(). The failure is
caused by missing attached encoder in the process of adding
MST connector.
drm_dp_send_enum_path_resources() aux transaction is pushed after
mode probe, which causes conflict to drm_dp_mst_i2c_xfer(),
leading to the transaction timeout.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0e6613e46f ]
[why]
It is not safe to keep existing connector while entire topology
has been removed. Could lead potential impact to uapi.
Entirely unregister all the connectors on the topology,
and use a new set of connectors when the topology is plugged back
on.
[How]
Remove the drm connector entirely each time when the
corresponding MST topology is gone.
When hotunplug a connector (e.g., DP2)
1. Remove connector from userspace.
2. Drop it's reference.
When hotplug back on:
1. Detect new topology, and create new connectors.
2. Notify userspace with sysfs hotplug event.
3. Reprobe new connectors, and reassign CRTC from old (e.g., DP2)
to new (e.g., DP3) connector.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30049754ab ]
[WHY]
Previously night light forced a full update by
applying a transfer function update regardless of if it was changed.
This logic was removed,
Now gamma surface updates are only applied when there is also a plane
info update, this does not work in cases such as using the night light
slider.
[HOW]
When moving the night light slider we will perform a full update if
the gamma has changed and there is a surface, even when the surface
has not changed. Also get stream updates in setgamma prior to
update planes and stream.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
