The vaddr field in struct ast_plane serves no purpose. Its value
can be calculated easily from the VRAM base plus the plane offset.
Do so and remove the field.
In ast_primary_plane_helper_get_scanout_buffer(), remove the test
for vaddr being NULL. This cannot legally happen.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://lore.kernel.org/r/20250324094520.192974-3-tzimmermann@suse.de
User-space cursor-image data is encoded in ARBG8888, while hardware
supports ARGB4444. Implement the format conversion as part of the
format-helper framework, so that other drivers can benefit.
This allows to respect the damage area of the cursor update. In
previous code, all cursor image data had to be converted on each
update. Now, only the changed areas require an update. The hardware
image is always updated completely, as it is required for the
checksum update.
The format-conversion helper still contains the old implementation's
optimization of writing 2 output pixels at the same time.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250217122336.230067-3-tzimmermann@suse.de
Setting the cursor image requires a 32-bit checksum of the cursor
image data. The current cursor code converts the image to ARGB4444
format and computes the checksum in a single step. Moving the
checksum calculation into a separate helper will allow to move the
format conversion into a shared helper.
v2:
- don't loop for checksum'ing final pixel (Jocelyn)
- fix typo in commit message (Jocelyn)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250217122336.230067-2-tzimmermann@suse.de
Mode lines are independent from hardware Gen or TX chip, so hide all
VBIOS mode tables in ast_vbios.c.
Move the look-up code for VBIOS modes from ast_vbios_get_mode_info()
to ast_vbios_find_mode(). The new look-up function respects the
supported-mode flags in struct ast_device. For example, if a device
does not have struct ast_device.support_fullhd set, the helper does
not return a valid mode for 1920x1080. Taking the supported-mode flags
into account allows for making the VBIOS tables the single reference
for validating and setting display modes against hardware capabilities.
v2:
- replace mode switch with look-up table (Jocelyn)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250131092257.115596-11-tzimmermann@suse.de
VBIOS mode tables are terminated by an entry with a refresh rate of
0xff. The code is hard to read and fragile to use. Therefore create
an empty entry with AST_VBIOS_MODE_INVALID to terminate each mode list.
Stop at the invalid entry when searching for modes in the tables.
Instead of testing for refresh == 0xff, test with a helper function if
the mode's size and refresh have meaningful values.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250131092257.115596-10-tzimmermann@suse.de
The ast driver looks up supplied display modes from an internal list of
display modes supported by the VBIOS.
Do not use the crtc_-prefixed display values from struct drm_display_mode
for looking up the VBIOS mode. The fields contain raw values that the
driver programs to hardware. They are affected by display settings like
double-scan or interlace.
Instead use the regular vdisplay and hdisplay fields for lookup. As the
programmed values can now differ from the values used for lookup, set
struct drm_display_mode.crtc_vdisplay and .crtc_hdisplay from the VBIOS
mode.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250131092257.115596-9-tzimmermann@suse.de
The ast driver matches DRM display modes against an internal list of
modes supported by the VBIOS. Matching H/V sync flags between modes is
preferred, but optional. If sync flags are not matching, the driver
would program the VBIOS settings to hardware and let the display handle
the difference.
DRM modes are generated from attached displays or standard mode lines.
Therefore differences to the VBIOS modes are not just cosmetical, but
signal possible incompatibility with the display hardware.
Hence make matching H/V sync flags mandatory. If the VBIOS does not
support a certain mode, we should report it as unsupported. Note that
the VBIOS mode tables all appear to refer to standard modes.
(If sync flags really make no difference to the VBIOS, the ast driver
shouldn't match them in the first place.)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250131092257.115596-8-tzimmermann@suse.de
Detect support for 1920x1080 (FullHD) in ast_detect_widescreen(). The
flag is cleared by default. The test logic has been taken from existing
code in ast_crtc_helper_mode_valid(). The code in that function is being
replaced by the new flag.
For Gen3, a new branch duplicates the Gen2 logic and adds a test for
AST2200. Gen2 adds a test for AST2100.
v2:
- use fullhd flag for setting max width/height
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250131092257.115596-6-tzimmermann@suse.de
Ast's BMC connector tracks the status of an underlying physical
connector and updates the BMC status accordingly. This functionality
works around GNOME's settings app, which cannot handle multiple
outputs on the same CRTC.
The workaround is now obsolete as all code for physical outputs
handle BMC support internally. Hence, remove the driver's code and
the BMC output entirely.
v3:
- remove struct ast_bmc_connector
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240815151953.184679-12-tzimmermann@suse.de
The place for link training is in the encoder's atomic_enable
helper. Remove all related tests from other helper ASTDP functions;
especially ast_astdp_is_connected(), which tests HPD status.
DP link training is controlled by the firmware. A status flag reports
success or failure. The process can be fragile on Aspeed hardware. Moving
the test from connector detection to the atomic_enable allows for several
retries and a longer timeout.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240717143319.104012-5-tzimmermann@suse.de
The function ast_crtc_dpms() is left over from when the ast driver
did not implement atomic modesetting. But DPMS is not supported by
atomic modesetting and the helper is only called to enable or
disable the CRTC sync pulses. Inline the function into its callers.
To disable the CRTC, ast sets (AST_DPMS_VSYNC_OFF | AST_DPMS_HSYNC_OFF)
in VGACRB6. Replace the constants with the correct register constants
for VGACRB6.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240627153638.8765-8-tzimmermann@suse.de
The SCREEN_DISABLE bit controls scanout from display memory. The bit
affects all planes, so set it only in the CRTC's atomic enable and
disable functions.
A number of bugs affect this fix. First of all, ast_set_std_regs()
tries to set VGASR1 except for the SD bit. But the read bitmask is
invert, so it preserves anything except the SD bit. Fix this by
re-inverting the read mask.
The second issue is that primary-plane and CRTC helpers modify the
SD bit. The bit controls scanout for all planes, primary and HW
cursor, so set it only in the CRTC code.
Further add a constant to represent the SD bit in VGASR1. Keep the
plane's atomic_disable around to make the DRM framework happy.
v2:
- fix typos in commit message
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240627153638.8765-7-tzimmermann@suse.de
Several color registers are programmed in the DPMS code of the CRTC's
atomic_enable helper and the primary plane's atomic_update. It requires
the color format and the display mode.
Both code paths handle different cases: the DPMS's code will not be
executed if the color format changes without a full mode switch. The
plane's code only runs if the color format changes, but ignores
display-mode changes.
The color format is a property of the primary plane, so consolidate all
color-format code in the plane's atomic_update. Remove it from the DPMS
helper.
v2:
- clarify commit message (Jocelyn)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240627153638.8765-5-tzimmermann@suse.de
Do all mode setting in ast_crtc_helper_mode_set_nofb(), which
always runs after disabling the CRTC and before programming the
planes. Removes implicit synchronization between the CRTC's
atomic disable, enable and the vertical retrace.
Display-mode updates require HW cursors to be disabled. The HW
cursor only picks up changes at vertical retrace periods. So the
CRTC's atomic_disable helper waited for the retrace to delay any
following mode-setting operations, which then happened in
atomic_enable. See [1] for a description of the problem.
With the CRTC helper callback mode_set_nofb, we can now synchronize
and reprogram in the same place. As it always runs before the plane
update, the plane code can be reordered with the CRTC's later
atomic_enable et al.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/series/79914/ # 1
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240627153638.8765-4-tzimmermann@suse.de
Add support for the drm_panic module, which displays a message to
the screen when a kernel panic occurs.
v7
* Use drm_for_each_primary_visible_plane()
v8:
* Replace get_scanout_buffer() logic with drm_panic_set_buffer()
(Thomas Zimmermann)
v9:
* Revert to using get_scanout_buffer() (Sima)
* move get_scanout_buffer() to plane helper functions
v12:
* Use array for map and pitch in struct drm_scanout_buffer
to support multi-planar format later. (Thomas Zimmermann)
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Acked-by: Sui Jingfeng <sui.jingfeng@linux.dev>
Tested-by: Sui Jingfeng <sui.jingfeng@linux.dev>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20240409163432.352518-10-jfalempe@redhat.com
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Implement polling for VGA and SIL164 connectors. Set the flag
DRM_CONNECTOR_POLL_DISCONNECT for each to detect the removal of the
monitor cable. Implement struct drm_connector_helper_funcs.detect_ctx
for each type of connector by testing for EDID data.
The helper drm_connector_helper_detect_ctx() implements .detect_ctx()
on top of the connector's DDC channel. The function can be used by
other drivers as companion to drm_connector_helper_get_modes().
v6:
- change helper name to drm_connector_helper_detec_from_ddc()
(Maxime, Sui)
v5:
- share implementation in drm_connector_helper_detect_ctx() (Maxime)
- test for DDC presence with drm_probe_ddc() (Maxime, Jani)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Acked-by: Sui Jingfeng <sui.jingfeng@linux.dev>
Acked-by: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240325200855.21150-13-tzimmermann@suse.de
The modeset lock protects the DDC code from concurrent modeset
operations, which use the same registers. Move that code from the
connector helpers into the DDC helpers .pre_xfer() and .post_xfer().
Both, .pre_xfer() and .post_xfer(), enclose the transfer of data blocks
over the I2C channel in the internal I2C function bit_xfer(). Both
calls are executed unconditionally if present. Invoking DDC transfers
from any where within the driver now takes the lock.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sui Jingfeng <sui.jingfeng@linux.dev>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Tested-by: Sui Jingfeng <sui.jingfeng@linux.dev>
Link: https://patchwork.freedesktop.org/patch/msgid/20240325200855.21150-11-tzimmermann@suse.de
Rename ast_i2c.c to ast_ddc.c and move its interface into the
new header ast_ddc.h. Update all include statements as necessary
and change the adapter name to 'AST DDC bus'.
This avoids including I2C headers in the driver's main header file,
which doesn't need them. Renaming files to _ddc indicates that the
code is about the DDC. I2C is really just the underlying bus here.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sui Jingfeng <sui.jingfeng@linux.dev>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240325200855.21150-6-tzimmermann@suse.de
