Backmerging to get v6.15-rc1 into drm-misc-next. Also fixes a
build issue when enabling CONFIG_DRM_SCHED_KUNIT_TEST.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
timer_delete[_sync]() replaces del_timer[_sync](). Convert the whole tree
over and remove the historical wrapper inlines.
Conversion was done with coccinelle plus manual fixups where necessary.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The drm_bridge structure contains an encoder pointer that is widely used
by bridge drivers. This pattern is largely documented as deprecated in
other KMS entities for atomic drivers.
However, one of the main use of that pointer is done in attach to just
call drm_bridge_attach on the next bridge to add it to the bridge list.
While this dereferences the bridge->encoder pointer, it's effectively
the same encoder the bridge was being attached to.
We can make it more explicit by adding the encoder the bridge is
attached to to the list of attach parameters. This also removes the need
to dereference bridge->encoder in most drivers.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250313-bridge-connector-v6-1-511c54a604fb@kernel.org
Signed-off-by: Maxime Ripard <mripard@kernel.org>
The continual trickle of small conversion patches is grating on me, and
is really not helping. Just get rid of the 'remove_new' member
function, which is just an alias for the plain 'remove', and had a
comment to that effect:
/*
* .remove_new() is a relic from a prototype conversion of .remove().
* New drivers are supposed to implement .remove(). Once all drivers are
* converted to not use .remove_new any more, it will be dropped.
*/
This was just a tree-wide 'sed' script that replaced '.remove_new' with
'.remove', with some care taken to turn a subsequent tab into two tabs
to make things line up.
I did do some minimal manual whitespace adjustment for places that used
spaces to line things up.
Then I just removed the old (sic) .remove_new member function, and this
is the end result. No more unnecessary conversion noise.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert the omap drm driver from always returning zero in the
remove callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230507162616.1368908-35-u.kleine-koenig@pengutronix.de
Using the SET_RUNTIME_PM_OPS() macro causes a warning about the
referenced functions when they are marked static but not __maybe_unused:
drivers/gpu/drm/omapdrm/dss/dss.c:1572:12: error: unused function 'dss_runtime_suspend' [-Werror,-Wunused-function]
drivers/gpu/drm/omapdrm/dss/dss.c:1584:12: error: unused function 'dss_runtime_resume' [-Werror,-Wunused-function]
drivers/gpu/drm/omapdrm/dss/dispc.c:4845:12: error: unused function 'dispc_runtime_suspend' [-Werror,-Wunused-function]
drivers/gpu/drm/omapdrm/dss/dispc.c:4860:12: error: unused function 'dispc_runtime_resume' [-Werror,-Wunused-function]
Fixes: b92f7ea556 ("drm/omap: dss: Make use of the helper macro SET_RUNTIME_PM_OPS()")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211205131612.3192652-1-arnd@kernel.org
msm-next pull request has a baseline with stuff from -fixes, roll
forward first.
Some simple conflicts in amdgpu, ttm and one in i915 where git gets
confused and tries to add the same function twice.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Panel drivers can send DSI commands in panel's prepare(), which happens
before the bridge's enable() is called. The OMAP DSI driver currently
only sets up the DSI interface at bridge's enable(), so prepare() cannot
be used to send DSI commands.
This patch fixes the issue by making it possible to enable the DSI
interface any time a command is about to be sent. Disabling the
interface is be done via delayed work.
Clarifications for the delayed disable work and the panel doing DSI
transactions:
bridge_enable: If the disable callback is called just before
bridge_enable takes the dsi_bus_lock, no problem, bridge_enable just
enables the interface again. If the callback is ran just after
bridge_enable's dsi_bus_unlock, no problem, dsi->video_enabled == true
so the callback does nothing.
bridge_disable: similar to bridge-enable, the callback won't do anything
if video_enabled == true, and after bridge-disable has turned the video
and the interface off, there's nothing to do for the callback.
omap_dsi_host_detach: this is called when the panel does
mipi_dsi_detach(), and we expect the panel to _not_ do any DSI
transactions after (or during) mipi_dsi_detatch(), so there are no
race conditions.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215104657.802264-85-tomi.valkeinen@ti.com
ULPS is a niche power-saving feature which only really affects command
mode panels showing a static picture. I know the ULPS code used to work
very long time ago, but I could not get it working with the current
driver. As the ULPS code is not trivial and includes delayed work (so
lots of chances for race issues), and just keeping DSI video and command
mode panels working has been challenging enough even without ULPS, lets
remove ULPS support.
When the DSI driver works reliably for command and video mode displays,
someone interested can work on ULPS and add it back if the power saving
is substantial enough.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215104657.802264-83-tomi.valkeinen@ti.com
The "channel" usage in omap dsi driver is confusing. We have three
different "channels":
1) DSI virtual channel ID. This is a number from 0 to 3, included in the
packet payload.
2) VC. This is a register block in the DSI IP. There are four of those
blocks. A VC is a DSI "pipeline", with defined fifo settings, data
source (cpu or dispc), and some other settings. It has no relation to
the 1).
3) dispc channel. It's the "pipeline" number dispc uses to send pixel
data.
The previous patch handled the third case.
To start fixing 1) and 2), we first rename all uses of 'channel' to
'vc', as in most of the cases that is the correct thing to use.
However, in some places 1) and 2) have gotten mixed up (i.e. the code
uses msg->channel when it should use vc), which will be fixed in the
following patch.
Note that mixing 1) and 2) currently is "fine", as at the moment we only
support DSI peripherals with DSI virtual channel 0, and we always use
VC0 to send data. So both 1) and 2) are always 0.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215104657.802264-66-tomi.valkeinen@ti.com
The OMAP DSI command mode panel driver used to send page & column
address before each frame update, and this code was moved into the DSI
host driver when converting it to the DRM bridge model.
However, it's not really required to send the page & column address
before each frame. It's also something that doesn't really belong to the
DSI host driver, so we should drop the code.
That said, frame updates break if we don't send _something_ between the
frames. A NOP command does the trick.
It is not clear if this behavior is as expected from a DSI command mode
frame transfer, or is it a feature/issue with OMAP DSI driver, or a
feature/issue in the command mode panel used.
Most likely this is related to the following from the DSI spec:
"To enable PHY synchronization the host processor should periodically
end HS transmission and drive the Data Lanes to the LP state. This
transition should take place at least once per frame."
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201215104657.802264-62-tomi.valkeinen@ti.com
