Flow for creating Tx topology is the same as for VF port representors,
but the devlink port is stored in different place (sf->devlink_port).
When creating VF devlink lock isn't taken, when creating subfunction it
is. Setting Tx topology function needs to take this lock, check if it
was taken before to not do it twice.
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement attaching and detaching SF port representor. It is done in the
same way as the VF port representor.
SF port representor is always added or removed with devlink
lock taken.
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement subfunction driver. It is probe when subfunction port is
activated.
VSI is already created. During the probe VSI is being configured.
MAC unicast and broadcast filter is added to allow traffic to pass.
Store subfunction pointer in VSI struct. The same is done for VF
pointer. Make union of subfunction and VF pointer as only one of them
can be set with one VSI.
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Implement devlink port handlers responsible for ethernet type devlink
subfunctions. Create subfunction devlink port and setup all resources
needed for a subfunction netdev to operate. Configure new VSI for each
new subfunction, initialize and configure interrupts and Tx/Rx resources.
Set correct MAC filters and create new netdev.
For now, subfunction is limited to only one Tx/Rx queue pair.
Only allocate new subfunction VSI with devlink port new command.
Allocate and free subfunction MSIX interrupt vectors using new API
calls with pci_msix_alloc_irq_at and pci_msix_free_irq.
Support both automatic and manual subfunction numbers. If no subfunction
number is provided, use xa_alloc to pick a number automatically. This
will find the first free index and use that as the number. This reduces
burden on users in the simple case where a specific number is not
required. It may also be slightly faster to check that a number exists
since xarray lookup should be faster than a linear scan of the dyn_ports
xarray.
Co-developed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Changing the MAC address of the VFs is currently unsupported via devlink.
Add the function handlers to set and get the HW address for the VFs.
Signed-off-by: Karthik Sundaravel <ksundara@redhat.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
