Support for FAN_CTL ON/OFF is currently disabled only for IT8603E but
there are severl chips that don't support the configuration bits to turn
off fan control entirely. Generalise this support for any chip.
Add feature flag FEAT_FANCTL_ONOFF for chips that support configuration
bits for management of fan control off and assign all chips that support
the configuration.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Link: https://lore.kernel.org/r/20230527094756.3464256-1-frank@crawford.emu.id.au
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Configure the IT8622E chip to disable/re-enable access via an SMBus when
reading or writing the chip's registers.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Disable/re-enable access through SMBus for chip registers when they are
are being read or written.
For simple cases this is done at the same time as when a mutex is set,
however, within loops or during initialisation it is done separately.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
[groeck: Fixed multi-line alignment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Handle errors from it87_update_device(), which currently only occurs if
SMBus access locking fails.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
[groeck: Fixed handling in show_temp_type()]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add functions to disable and re-enable access by the SMBus for specific
chips.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Disabling configuration mode on some chips can result in system
hang-ups and access failures to the Super-IO chip at the
second SIO address. Never exit configuration mode on these
chips to avoid the problem.
This patch should be applied in conjunction with a previous one to
initialise the second chip for certain mother boards.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Link: https://lore.kernel.org/r/20230128060308.1549707-2-frank@crawford.emu.id.au
[groeck: Change feature bit from 28 to 19 to be continuous]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On various Gigabyte AM4 boards (AB350, AX370), the second Super-IO chip
(IT8792E) needs to be in configuration mode before accessing the first
due to a bug in IT8792E which otherwise results in LPC bus access errors.
This needs to be done before accessing the first Super-IO chip since
the second chip may have been accessed prior to loading this driver.
The problem is also reported to affect IT8795E, which is used on X299
boards and has the same chip ID as IT8792E (0x8733). It also appears
to affect systems with IT8790E, which is used on some Z97X-Gaming boards
as well as Z87X-OC, and other more recent Gigabyte boards.
Signed-off-by: Frank Crawford <frank@crawford.emu.id.au>
Link: https://lore.kernel.org/r/20230104060926.619686-3-frank@crawford.emu.id.au
[groeck: Made description pass checkpatch]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We have bool so use it consistently in all the drivers.
The following Coccinelle script was used:
@@
identifier T;
type t = { char, int };
@@
struct T {
...
- t valid;
+ bool valid;
...
}
@@
identifier v;
@@
(
- v->valid = 0
+ v->valid = false
|
- v->valid = 1
+ v->valid = true
)
followed by sed to fixup the comments:
sed '/bool valid;/{s/!=0/true/;s/zero/false/}'
Few whitespace changes were fixed manually. All modified drivers were
compile-tested.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Link: https://lore.kernel.org/r/20210924195202.27917-1-fercerpav@gmail.com
[groeck: Fixed up 'u8 valid' to 'boool valid' in atxp1.c]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
coccinelle complains about
WARNING opportunity for kobj_to_dev()
in several files, resulting in one-by-one patch submissions.
Handle all remaining instances in one go.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After a suspend / resume cycle we possibly need to reapply chip registers
settings that we had set or fixed in a probe path, since they might have
been reset to default values or set incorrectly by a BIOS again.
Tested on a Gigabyte M720-US3 board, which requires routing internal VCCH5V
to in7 (and had it wrong again on resume from S3).
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
[groeck: Return value from it87_resume_sio() is unused; make it void]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This commit splits out chip registers setting code on probe path to
separate functions so they can be reused for setting the device properly
again when system resumes from suspend.
While we are at it let's also make clear that on IT8720 and IT8782 it's
the VCCH5V line that is (possibly) routed to in7.
This will make it consistent with a similar message that it printed on
IT8783.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8705F is known to respond on both SIO addresses. Registering it twice
may result in system lockups.
Reported-by: Russell King <linux@armlinux.org.uk>
Fixes: e84bd9535e ("hwmon: (it87) Add support for second Super-IO chip")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The chip is similar to IT8732E, but supports only three fans
and pwm outputs instead of four (the driver currently does not
support the 4th fan and pwm output of IT8732E).
Note that the chip ID is 0x8733, not 0x8792 as one would expect.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In IT8620E, after setting pwm control to manual, it was observed that
pwm values for fan 4..6 have reversed results (writing 0 results in fans
running at full speed, writing 255 results in fans turned off).
With the new PWM control, pwm polarity for pwm control 4..6 is specified
in its pwm control registers. Those registers are overwritten when setting
the pwm mode or the temperature mapping. Do not touch bit 2..6 of pwm
control registers on register writes to fix the problem.
Cc: stable@vger.kernel.org # 4.9+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pwm4 is enabled if bit 2 of GPIO control register 4 is disabled,
not when it is enabled. Since the check is for the skip condition,
it is reversed. This applies to both IT8620 and IT8628.
Fixes: 36c4d98a78 ("hwmon: (it87) Add support for all pwm channels ...")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If sensor attributes were never read, the pwm control data has not been
initiialized, which can cause wrong driver behavior. Ensure that cached
data is current before acting on it.
Cc: stable@vger.kernel.org # 4.4+
Reported-by: Kevin Folz <kfolz@evertz.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Configuration registers on ITE8622 are different to 8620 and 8628 and
require special handling. Also, the chip supports up to 5 pwm controls.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8622E is similar to IT8620E, but only supports five pwm controls and
five fan tachometers.
Originally-from: Kevin Folz <kfolz@evertz.com>.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On IT8622E and IT8628E, VIN3 is expected to be connected to +5V.
Add feature flag and reflect in input label.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Remove the index comments at the end of it87_attributes_in. They
serve no purpose (as there is no reference to them in
it87_in_is_visible) and some of them were obviously wrong.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Coverity reports:
result_independent_of_operands: data->features & (65536UL /* 1UL << 16 */)
is always 0 regardless of the values of its operands. This occurs as the
logical operand of if.
data->features needs to be 32 bit wide since there are more than 16 features.
Fixes: cc18da79d9 ("hwmon: (it87) Support up to 6 temperature sensors ... ");
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Several of the chips supported by this driver have a configuration
register to enable fan4 and fan5. Use those registers to determine
if fan4 and fan5 tachometers are supported.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On/Off mode is only supported for pwm controls 0-2, and not supported at all for
IT8603E/IT8623E. For pwm controls 3-6 and for IT8603E/IT8623E, SmartGuardian mode
is always enabled. Use it and set the pwm value to the maximum if fan control
is disabled.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix various checkpatch complaints to clean up the code and
make it easier to read.
CHECK: Do not include the paragraph about writing to the FSF
CHECK: Alignment should match open parenthesis
CHECK: Logical continuations should be on the previous line
CHECK: No space is necessary after a cast
CHECK: Please don't use multiple blank lines
CHECK: Please use a blank line after function/struct/union/enum
declarations
CHECK: spaces preferred around that '+' (ctx:VxV)
WARNING: Missing a blank line after declarations
No functional change.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Using array size defines makes it much easier to find errors
in index values and loop counts.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Using the BIT macro makes the code a little easier to read and has the
added benefit of making checkpatch happy.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
